spectral scan control interface is exposed through debugfs eentry.
Relayfs is used to collect the spectral data. These interfaces are
similar to ath10k spectral.
spectral debugfs interfaces are below,
echo background > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
echo trigger > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
iw dev wlan0 scan
echo disable > /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan_ctl
cat /sys/kernel/debug/ieee80211/phy0/ath11k/spectral_scan0 > fft_samples.dump
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-2-git-send-email-periyasa@codeaurora.org
Add direct buffer ring (dbring) with helper API, which is used by the
spectral scan. Initialise the direct buffer ring based on the dma ring
capability, which get announced in the wmi service ready extended event.
This ring is slightly changed from data path rings. Compare to data path
ring this ring shares the hp and tp address to firmware though WMI commands.
Also the replenish buffer size is derived from firmware announcement.
driver receive indication through WMI event
WMI_PDEV_DMA_RING_BUF_RELEASE_EVENTID.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591688014-26441-1-git-send-email-periyasa@codeaurora.org
With addition of 6Ghz channels, it is possible that wmi buffer size can
exceed the maximum wmi buffer size. So iterate over the channel list,
and send multiple messages till channel list is empty.
Also mark PSC channel flag for 6GHz channels accordingly.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-8-pradeepc@codeaurora.org
If 6 ghz channel is a Preferred Scanning Channel(PSC), mark
the channel flag accordingly when updating channel list to firmware.
This will be used when making scanning decision in 6GHz channels.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-6-pradeepc@codeaurora.org
This adds support required for configuring min_data_rate of 6GHz oper IE
and peer_he_caps_6ghz in peer assoc command. The Minimum Rate field
indicates the minimum rate, in units of 1 Mb/s, that the non-AP STA is
allowed to use for sending PPDUs as defined in IEEE P802.11ax™/D6.0.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-5-pradeepc@codeaurora.org
As 6GHz cahnnel numbers overlap with those of 5GHz and 2GHz bands,
it is necessary to use frequency when determining the band info
in rx path.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200603001724.12161-4-pradeepc@codeaurora.org
The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:
struct foo {
int stuff;
struct boo array[];
};
By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.
Also, notice that, dynamic memory allocations won't be affected by
this change:
"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]
sizeof(flexible-array-member) triggers a warning because flexible array
members have incomplete type[1]. There are some instances of code in
which the sizeof operator is being incorrectly/erroneously applied to
zero-length arrays and the result is zero. Such instances may be hiding
some bugs. So, this work (flexible-array member conversions) will also
help to get completely rid of those sorts of issues.
This issue was found with the help of Coccinelle.
[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 7649773293 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200504201224.GA32282@embeddedor
This patch add supports to reset the per peer htt stats.
Usage:
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/<peer MAC addr>/htt_peer_stats_reset
While doing so, sync the wmi services between FW and host.
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1588610147-20231-1-git-send-email-tamizhr@codeaurora.org
This patch adds support for ethernet rxtx mode to the driver. The feature
is enabled via a new module parameter. If enabled to driver will enable
the feature on a per vif basis if all other requirements were met.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200430152814.18481-1-john@phrozen.org
Pktlog data are different among the chipset & chipset versions.
As part of enhancing the user space script to decode the pktlog
trace events generated, it is desirable to know which chipset or
which chipset version has provided the events and thereby decode
the pktlogs appropriately.
Pktlog checksum helps to determine the chipset variant which is
given by the firmware in the struct wmi_ready_event.
Pktlog checksums are computed during the firmware build.
So, adding that pktlog checksum in the pklog trace events.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585234155-30574-1-git-send-email-mkenna@codeaurora.org
Add support to test aggregation procedures (addba/addba_resp/delba)
manually by adding the required callbacks in sta debugfs files.
To enable automatic aggregation in target,
echo 0 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
For manual mode,
echo 1 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/aggr_mode
To send addba response,
echo 0 25 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba_resp
To send addba,
echo 1 32 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/addba
To send delba,
echo 0 1 37 > /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/
stations/XX:XX:XX:XX:XX:XX/delba
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1585213026-28406-1-git-send-email-mkenna@codeaurora.org
Current implementation of pdev based reo destination ring
selection is replaced by hash based ring selection so as to
ensure all the available rings are utilized for better performance.
The 4 reo destination rings are selected by the HW based on the
hash value computed from the received packet based on the 5 tuple
{ip src/ip dst/src port/dst port/protocol}. Out of the 32 hash values
used by the hw, the driver assigns 8 values per reo destination ring
to each of the 4 reo destination rings.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the he_operation field of the beacon sets a BSS color, we need to inform
the FW of the settings. This patch adds the WMI command handlers required
to do so.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Temperature sensor generates electrical analog voltage from temperature
of each chain. The analog voltage is converted to digital value through
ADC. For reading temperature values fom user space, hw monitoring device
is used.
Whenever the user requests for current temperature, the driver sends WMI
command and wait for response. For reading temperature,
cat /sys/class/ieee80211/phy*/device/hwmon/hwmon2/temp1_input
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Thermal cooling device support is added to control the temperature by
throttling the data transmission for the given duration. Throttling is
done by suspending all data tx queues by given percentage of time. The
thermal device allows user to configure duty cycle.
Throttling can be disabled by setting the duty cycle to 0. The cooling
device can be found under /sys/class/thermal/cooling_deviceX/.
Corresponding soft link to this device can be found under phy folder.
/sys/class/ieee80211/phy*/device/cooling_device.
To set duty cycle as 40%,
echo 40 >/sys/class/ieee80211/phy*/device/cooling_device/cur_state
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FIELD_SIZEOF() macro was redundant, and is being removed from the
kernel. Since commit c593642c8b ("treewide: Use sizeof_field() macro")
this is one of the last users of the old macro, so replace it.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Clang warns:
drivers/net/wireless/ath/ath11k/wmi.c:1827:23: warning: implicit
conversion from enumeration type 'enum wmi_scan_priority' to different
enumeration type 'enum scan_priority' [-Wenum-conversion]
arg->scan_priority = WMI_SCAN_PRIORITY_LOW;
~ ^~~~~~~~~~~~~~~~~~~~~
1 warning generated.
wmi_scan_priority and scan_priority have the same values but the wmi one
has WMI prefixed to the names. Since that enum is already being used,
get rid of scan_priority and switch its one use to wmi_scan_priority to
fix this warning.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Link: https://github.com/ClangBuiltLinux/linux/issues/808
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch sets the correct BA buffer size when we are in HE mode.
Without this change we are not able to receive 256 bitmapped BA frames.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This makes the code consistent with the recent sc to ab rename.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a WMI call helper to set the powersave mode of a STA interface.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In conf_tx() mac operation callback, we are truncating the tx
params cw_min and cw_max due to lower data type cast. so modified
the data type of cwmin and cwmax to avoid the trucation issue.
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The current ath11k driver failed to parse
wmi_tlv_svc_rdy_ext_parse if there is change in
wmi_mac_phy_capabilities length with below error.
ath11k c000000.wifi1: failed to extract mac caps, idx :0
ath11k c000000.wifi1: failed to parse tlv -22
This is needed to get firmware version
WLAN.HK.2.0.0.1-00240-QCAHKSWPL_SILICONZ-1 working.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Trigger the WMI call en/disabling OBSS PD when the bss config changes or we
assoc to an AP that broadcasts the IE.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add target wait time wmi calls to the driver. En/disable the support
from when the bss_config changes. We ignore the cmd completion events.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add basic HE support to the driver. The sband_iftype data is generated from
the capabilities read from the FW.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Everytime a new peer gets associated, we see the following message in the log
- ath11k c000000.wifi1: Unknown eventid: 0x6017
Ignore this event for now. We probably need to handle the event properly when
we add OMI support.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.
Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.
Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.
Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.
The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:
https://github.com/kvalo/ath11k-firmware
This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.
The driver has had multiple authors who are listed in alphabetical
order below.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
