This is a small update to fix an error I saw where a few functions do not
have a blank line in between them.
Affects smd.c and main.c - no logic is affected by this change.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-3-bryan.odonoghue@linaro.org
This commit marks all smd.c functions that are only used inside of smd.c as
static. Previous commits added some VHT specific setup functions non-static
which is the right thing to do in terms of having granular git commits that
compile warning free. What we really want is for local not global scope on
those functions.
This patch makes the conversion from global to local scope.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150845.2179320-2-bryan.odonoghue@linaro.org
In order to send VHT parameters to wcn3680 we need to pass the extended V1
parameter structures to the firmware. These commands need to have the
version number set to 1.
This patch makes the conversion. The conversion consists of
1. Setting the version number for wcn3680 or leaving it at 0 otherwise
2. Setting the size of the packet header lower for wcn3620 and wcn3660
Once done all three chips can continue to use the same code to pass
parameters to their respective firmware. In the case of the wcn3680 the
passed structures will be slightly larger to accommodate communication of
VHT descriptors.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-3-bryan.odonoghue@linaro.org
In order to pass 802.11ac VHT parameters from the SoC to wcn36xx we need to
use the V1 data structures associated with BSS and STA parameters.
The means of identifying a V1 data-structure is via the SMD version field.
This patch defines a INIT_HAL_MSG_V1() which operates the same way as
INIT_HAL_MSG() with the exception that it defines VERSION1 as opposed to
VERSION0.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150822.2179261-2-bryan.odonoghue@linaro.org
This commit makes use of wcn36xx_smd_set_bss_vht_params() to extract VHT
parameters from the 80211_sta structure and latch appropriate bits in the
bss_params_v1 structure for transmission to the wcnss firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-5-bryan.odonoghue@linaro.org
This commit modifies wcn36xx_smd_start() so that it can download wcn3680
specific firmware parameters if we are talking to the wcn3680. If not the
original generic firmware parameter table should continue to be used for
wcn3620 and wcn3660.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-4-bryan.odonoghue@linaro.org
This commit defines a firmware configuration for the wcn3680 which
represents a working downstream configuration. This configuration has been
successfully applied to the upstream driver with antecedent patches
resulting in the same or better through-put in comparison to the
downstream driver on the test hardware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150747.2179122-3-bryan.odonoghue@linaro.org
For the 80MHz channel we need to set the PHY mode to one of four PHY modes
that span the 80MHz range.
This patch latches the hw_value PHY field previously defined for 5GHz
channels directly to the parameter passed to the firmware.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-6-bryan.odonoghue@linaro.org
Uses HW_VALUE_CHANNEL() to extract the channel number from a
struct ieee80211_channel->hw_value. Once done we can use the upper bits of
the hw_value to encode PHY related data.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150708.2179043-3-bryan.odonoghue@linaro.org
wcn36xx_smd_config_bss_v0() and wcn36xx_smd_config_bss_v1() have been
designed to operate in standalone fashion. As a result we can drop the
dead code now present in wcn36xx_smd_config_bss() and happily remove one
kzalloc from the BSS config path as we do so.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-8-bryan.odonoghue@linaro.org
A previous patch added wcn36xx_smd_config_bss_v0() this patch converts the
version 0 data-path in wcn36xx_smd_config_bss() to use
wcn36xx_smd_config_bss_v0().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-7-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_config_bss_v0() as a step along the road of
functionally decomposing wcn36xx_smd_config_bss().
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-6-bryan.odonoghue@linaro.org
This patch updates wcn36xx_smd_config_bss_v1() to update on internally
derived parameters only, specifically making use of STA v1 wrapper routines
previously added.
Once done we no longer need to pass a struct wcn36xx_hal_config_bss_req_msg
which gives us options in later patches to eliminate the kzalloc() in
wcn36xx_smd_config_bss entirely.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-5-bryan.odonoghue@linaro.org
This commit moves BSS parameter setup to a separate function
wcn36xx_smd_set_bss_params(). This will allow for further functional
decomposition and fewer kzalloc() operations in subsequent patches.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-4-bryan.odonoghue@linaro.org
In order to facilitate functional decomposition of
wcn36xx_smd_config_bss() we need to move wcn36xx_smd_set_sta_params() later
in function.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-3-bryan.odonoghue@linaro.org
This commit functionally decomposes wcn36xx_smd_config_sta into a clearly
defined wcn36xx_smd_config_sta_v0 and wcn36xx_smd_config_sta_v1 path.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150631.2178970-2-bryan.odonoghue@linaro.org
This commit adds a wrapper function wcn36xx_smd_set_sta_params_v1() which
calls into wcn36xx_smd_set_sta_params() and then subsequently sets
version-1 specific parameters.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-8-bryan.odonoghue@linaro.org
This commit adds wcn36xx_smd_set_bss_vht_params(). The job of this function
is to decide if the BSS is VHT capable and if so set the appropriate bit
in the BSS parameter structure for passing to the firmware.
VHT Channel width set is not set since we don't support 160MHz.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-7-bryan.odonoghue@linaro.org
Adds a routine to allow setting the LDPC bit for HT parameter passing
inside the version 1 STA parameters data structure.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-6-bryan.odonoghue@linaro.org
This commit adds support for setting VHT parameters based on the declared
VHT capability bits in the VHT capability structure.
We cannot do 160MHz so VHT Channel width set should be zero.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-5-bryan.odonoghue@linaro.org
Toggling the LDPC enabled bit is possible only via the extended V1
data-structure. This function provides a means of setting the default
depending on chip-type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-4-bryan.odonoghue@linaro.org
This commit adds support for setting default VHT parameters, which are
exposed by the extended version 1 STA parameter type.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150552.2178882-3-bryan.odonoghue@linaro.org
This patch converts the internal data structure used to store data-rates
from version 0 to version 1.
This allows us to extend out the internal storage to represent VHT
parameters.
Using the extended version 1 data-structure allows us to avoid a whole raft
of version 1 specific fixup functions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-3-bryan.odonoghue@linaro.org
In order to pass VHT parameters to wcn3680 we need to use a super-set of
the V1 data-structures with additional VHT parameters tacked on.
This patch adds the additional fields to the STA and BSS parameter
structures.
Since neither wcn3620 nor wcn3660 support VHT the size of the passed
message is fixed to the previous message length. Subsequent changes will
differentiate between wcn3620/wcn3660 and wcn3680 which does use the larger
message size.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910150450.2178784-2-bryan.odonoghue@linaro.org
In order for the firmware to process extended V1 parameters with the
addtional VHT fields added we need to first enable the feature bit DOT11AC.
Once done the version number in the HAL message header will be acted upon
by the firmware.
Extended V1 parameters are a prerequisite for 802.11ac speeds since we
cannot communicate VHT parameters to the firmware absent the extended data
structures.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-11-bryan.odonoghue@linaro.org
Two pointers are already defined in this function "bss" and "sta" which
point to fields within msg_body->bss_params.
We can substantially reduce the amount of extraneous text in this function
by making use of those pointers. This change makes the code easier to read
and modify.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200829033846.2167619-10-bryan.odonoghue@linaro.org
By default, after associated to an AP, the wcn36xx bitrate adjustment
algorithm starts sending data at 1Mbps, and increases the rate slowly
(1Mbps, 2Mbps, 6Mbps...) over the further TX packets.
Starting at 1Mbps usually causes the initial throughput to be really
low and the maximum possible bitrate to be reached after about hundreed
of TX packets.
That can be improved by setting a different initial bitrate for data
packets via the ENABLE_DYNAMIC_RA_START_RATE configuration value, this
value can be a legacy or MCS rate.
This patch sets the starting bitrate value to MCS-5, which seems to be
a good compromise given it can be quickly adjusted low or up if necessary.
(and based on what I observed in the wild with some mobile devices)
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598345341-4505-1-git-send-email-loic.poulain@linaro.org
For software-driven scan, rely on mac80211 software scan instead
of internal driver implementation. The internal implementation
cause connection trouble since it keep the antenna busy during
the entire scan duration, moreover it's only a passive scanning
(no probe request). Therefore, let mac80211 manages sw scan.
Note: we fallback to software scan if firmware does not report
scan offload support or if we need to scan the 5Ghz band (currently
not supported by the offload scan...).
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1598288035-19790-1-git-send-email-loic.poulain@linaro.org
Increase the short/long retry limit to 15 in order to impove TX
robustness in noisy/busy environment. 15 is the default value
defined in the downstream driver. Observed number of ack timeout
is reduced with this change.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-4-git-send-email-loic.poulain@linaro.org
Several AMPDU sessions can be started, e.g. for different TIDs.
Currently the driver does not take care of the session ID when
requesting block-ack (statically set to 0), which leads to never
block-acked packet with sessions other than 0.
Fix this by saving the session id when creating the ba session and
use it in subsequent ba operations.
This issue can be reproduced with iperf in two steps (tid 0 strem
then tid 6 stream).
1.0 iperf -s # wcn36xx side
1.1 iperf -c ${IP_ADDR} # host side
Then
2.0 iperf -s -u -S 0xC0 # wcn36xx side
2.1 iperf -c ${IP_ADDR} -u -S 0xC0 -l 2000 # host side
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1595586052-16081-2-git-send-email-loic.poulain@linaro.org
There is a spelling mistake in a wcn36xx_err message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
clang triggers a warning about oversized stack frames that gcc does not
notice because of slightly different inlining decisions:
ath/wcn36xx/smd.c:1409:5: error: stack frame size of 1040 bytes in function 'wcn36xx_smd_config_bss' [-Werror,-Wframe-larger-than=]
ath/wcn36xx/smd.c:640:5: error: stack frame size of 1032 bytes in function 'wcn36xx_smd_start_hw_scan' [-Werror,-Wframe-larger-than=]
Basically the wcn36xx_hal_start_scan_offload_req_msg,
wcn36xx_hal_config_bss_req_msg_v1, and wcn36xx_hal_config_bss_req_msg
structures are too large to be put on the kernel stack, but small
enough that gcc does not warn about them.
Use kzalloc() to allocate them all. There are similar structures in other
parts of this driver, but they are all smaller, with the next largest
stack frame at 480 bytes for wcn36xx_smd_send_beacon.
Fixes: 8e84c25821 ("wcn36xx: mac80211 driver for Qualcomm WCN3660/WCN3680 hardware")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Replace calls to kmalloc followed by a memcpy with a direct call to
kmemdup.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Initialization is unneccessary when the variable is written before it is
read. There were some occasions in which the driver would initialize `ret'
during declaration without need.
Purely a cosmetic change with no functional impact.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case of WEP encryption, driver has to configure shared key for
associated station(s). Note that sta pointer is NULL in case of non
pairwise key, causing NULL pointer dereference with existing code
(sta_priv->is_data_encrypted). Fix this by using associated sta list
instead. This enables WEP support as client, WEP AP is non-functional.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce infrastructure for supporting Factory Test Mode (FTM) of the
wireless LAN subsystem. In order for the user space to access the
firmware in test mode the relevant netlink channel needs to be exposed
from the kernel driver.
The above is achieved as follows:
1) Register wcn36xx driver to testmode callback from netlink
2) Add testmode callback implementation to handle incoming FTM commands
3) Add FTM command packet structure
4) Add handling for GET_BUILD_RELEASE_NUMBER (msgid=0x32A2)
5) Add generic handling for all PTT_MSG packets
Signed-off-by: Eyal Ilsar <eilsar@codeaurora.org>
Signed-off-by: Ramon Fried <ramon.fried@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add a missing newline in wcn36xx_smd_send_and_wait() and also log the
command request and response type that was processed.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Drop the extra warning about failed allocations, both the core and the
only caller of this function will warn loud enough in such cases.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the interface is shut down, wcn36xx_smd_close() potentially races
against the queue worker. Make sure to cancel the work, and then free all
the remnants in hal_ind_queue manually.
This is again just a theoretical issue, not something that was triggered in
the wild.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the wifi driver core passes IE elements in the scan request, append
them to the firmware message. The driver currently tells the core that
it is capable of attaching up to WCN36XX_MAX_SCAN_IE_LEN octets, but
doesn't actually pass them to the the hardware.
Note that this patch doesn't fix a bug that was observed. The change is
merely done for the sake of completeness as the hardware supports
appending IEs in scans. Tests show that network scans work fine with
this patch applied.
Some defines were moved around to avoid cyclic include dependencies.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Pass the bss_type of the currently configured BSS in the message for the
scan request. Therefore, that setting needs to be kept in struct
wcn36xx_vif.
This seems to be only interesting when scanning for a specific SSID
and doesn't matter for regular wildcard scans.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the firmware sends a WCN36XX_HAL_SCAN_IND_DEQUEUED indication,
the request is apparently no longer valid. Attempts to stop the hardware
scan request subsequently will lead to the following error message, and
the hardware is no longer able to communicate with any AP:
[ 57.917186] wcn36xx: ERROR hal_stop_scan_offload response failed err=5
Interpreting this indicator message as scan abortion fixes this.
While at it, add a newline to a debug print.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware message to delete BSS keys expects a BSS index to be passed.
This field is currently hard-coded to 0. Fix this by passing in the index
we received from the firmware when the BSS was configured.
The encryption type in that message also needs to be set to what was used
when the key was set, so the assignment of vif_priv->encrypt_type is now
done after the firmware command was sent. This reportedly fixes the
following error in AP mode:
wcn36xx: ERROR hal_remove_bsskey response failed err=6
Also, AFAIU, when a BSS is deleted, the firmware apparently drops all the
keys associated with it. Trying to remove the key explicitly afterwards
will hence lead to the following message:
wcn36xx: ERROR hal_remove_bsskey response failed err=16
This is now suppressed with an extra check for the BSS index validity.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This prevents GCC warning.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware code cannot cope with requests to remove BSS indices that have
not previously been added. This primarily happens when the device is
suspended and then resumed. ieee80211_reconfig() then calls into
wcn36xx_bss_info_changed() with an empty bssid and BSS_CHANGED_BSSID set,
which subsequently leads to a firmware crash:
[ 43.647928] qcom-wcnss-pil a204000.wcnss: fatal error received: halMsg.c:4964:halMsg_DelBss: Invalid BSSIndex 0
[ 43.647959] remoteproc remoteproc0: crash detected in a204000.wcnss: type fatal error
To fix this, set bss_index to WCN36XX_HAL_BSS_INVALID_IDX for all bss
that have not been configured in the firmware, and don't call into the
firmware with invalid indices.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In case wcn36xx_smd_rsp_process() is called more than once before
hal_ind_work was dispatched, the messages will end up in hal_ind_queue,
but wcn36xx_ind_smd_work() will only look at the first message in that
list.
Fix this by dequeing the messages from the list in a loop, and only stop
when it's empty.
This issue was found during a review of the driver. In my tests, that
race never actually occured.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the WLAN interface is started the FW
version and caps are printed.
The caps now will be displayed only in debug mode.
Firmware version will be displayed only once on first
startup of the interface.
Change-Id: I4db6ea7f384fe15eebe4c3ddb1d1ccab00094332
Signed-off-by: Ramon Fried <rfried@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The wcn36xx_cancel_hw_scan method stops the hw scan and notify the
scan completion via ieee80211_scan_completed.
However, on scan offload cancellation, firmware sends a scan complete
indication, triggering a new call to ieee80211_scan_completed.
This leads to kernel warn since the scan has already been completed.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The second assignment to msg_body.min_ch_time is incorrect, it
should actually be to msg_body.max_ch_time.
Thanks to Bjorn Andersson for identifying the correct way to fix
this as my original fix was incorrect.
Detected by CoverityScan, CID#1463042 ("Unused Value")
Fixes: 2f3bef4b24 ("wcn36xx: Add hardware scan offload support")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The purpose of pushing indication on a list and handle these in a
separate worker is to allow the handlers to sleep. It does therefor not
make much sense to hold the queue spinlock through the entire indication
worker function.
By removing items from the queue early we don't need to hold the lock
throughout the indication worker, allowing the individual handlers to
sleep.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
