First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJetAhAAAoJEG4XJFUm622bADEH/A1OjAD3H1iZyTmXHP4T7yZe
TKJ+9I6B3BDR1czUTm+kUhrgBDNpdLLtu+b+5QXfpPLrtZ0FF/zjuazgueyqQpZ1
zudj+rG72njHpU0RKtO7wIBrCtckLPV0be+3026hztatJmJ7XQ9FvsanFPPsrrNv
0lh8E8kDUSynOW2me8FW1GBgDkGaBaicAs4FSjwNJC31Wo/VN5m9gEFkGpT1VJWP
l0xeEQ/N2mknQVuTR4CuMT9VJ0SNlJrLZpBVAqkmc170c3pKChl3LTNCnP925ye9
Nfqw2sQKgUPJKRbZR5wZTphGuu4krFv0ldWCvb0oFtZlCLIkiOz6+AA7b33oV2A=
=7ewK
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-05-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.8
First set of patches for v5.8. Changes all over, ath10k apparently
seeing most new features this time. rtw88 also had lots of changes due
to preparation for new hardware support.
In this pull request there's also a new macro to include/linux/iopoll:
read_poll_timeout_atomic(). This is needed by rtw88 for atomic
polling.
Major changes:
ath11k
* add debugfs file for testing ADDBA and DELBA
* add 802.11 encapsulation offload on hardware support
* add htt_peer_stats_reset debugfs file
ath10k
* enable VHT160 and VHT80+80 modes
* enable radar detection in secondary segment
* sdio: disable TX complete indication to improve throughput
* sdio: decrease power consumption
* sdio: add HTT TX bundle support to increase throughput
* sdio: add rx bitrate reporting
ath9k
* improvements to AR9002 calibration logic
carl9170
* remove buggy P2P_GO support
p54usb
* add support for AirVasT USB stick
rtw88
* add support for antenna configuration
ti wlcore
* add support for AES_CMAC cipher
iwlwifi
* support for a few new FW API versions
* new hw configs
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add framework for supporting specific PHY filter configuration,
which allows for application of various FW defined PHY filters
(one per antenna). Change phy_cfg_cmd to the new API (ver3).
Reading of configuration from platform's ACPI tables to be added
later when tables are defined.
Signed-off-by: Gil Adam <gil.adam@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200418110539.242a8f979592.I13c77a8a8dbf1a169b5052c7af1f8401ff3991ad@changeid
Add support for the new WOWLAN_GET_STATUS notification that contains a
new element that informs the driver of TIDs whose BA sessions were
closed during suspend.
Note that the new functionality of handling these closed sessions is not
implemented in this patch it. It only aligns to the new API version.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200417131727.b02153b94c1d.Ieb6291586d60f372d5a505604b18227ef97e7202@changeid
The API version lookup is parsed from a TLV and should be in shared code
make make it reusable across all opmodes.
Also change the function names from mvm to fw, since this is not
mvm-specific anymore.
Additionally, since this function is not just a single line of code, it
shouldn't be inline. Convert them to actual functions.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200421133326.cf94672dfcdb.I5ede9cc25ee8de7b8d2b5c574f917a18971da734@changeid
Due to some hardware issues, queue 31 isn't usable on devices that have
32 queues (7000, 8000, 9000 families), which is correctly reflected in
the configuration and TX queue initialization.
However, the firmware API and queue allocation code assumes that there
are 32 queues, and if something actually attempts to use #31 this leads
to a NULL-pointer dereference since it's not allocated.
Fix this by limiting to 31 in the IWL_MVM_DQA_MAX_DATA_QUEUE, and also
add some code to catch this earlier in the future, if the configuration
changes perhaps.
Cc: stable@vger.kernel.org # v4.9+
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200417100405.98a79be2db6a.I3a4af6b03b87a6bc18db9b1ff9a812f397bee1fc@changeid
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJefdsZAAoJEG4XJFUm622blekH/2fIoUtl8Kdih38hNjz63PLD
x+LCPjZdRjrmFGTSxnS1rZiIM7v2yXyLGiyq+yr2ltzkpTi8xWOkKL6US8RCew9R
otRtZyLrhgMLG2ExDna1fI5ZJAtLnxV31TCy6yrSUDZ8t4VxMNIB4si3WRzKvAfU
c+cQcsnWr+pCDnbxh53BcYIyiEqKlttw/fGuIKchKuYMQy7DV6nxMdTaAym5Szzi
Nlb8fhXWFaPrPQ6NtHb5WWm4Er3wtMzN/AG8aFVxjrik07vTxQKWamdT9CeK2tDT
iDbx2HaNCWFMulXeZMrc9+inoAzj3UjbPqH3OTUk9iHbVA0unc3CdEBFD9h928Q=
=D/FA
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-03-27' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.7
Third set of patches for v5.7. Nothing really special this time,
business as usual.
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
Major changes:
brcmfmac
* add USB autosuspend support
ath11k
* handle RX fragments
* enable PN offload
* add support for HE BSS color
iwlwifi
* support new FW API version
* support for EDCA measurements
* new scan API features
* enable new firmware debugging code
====================
Kalle gave me directions on how to resolve the iwlwifi conflict
as follows:
====================
When pulling this to net-next there's again a conflict in:
drivers/net/wireless/intel/iwlwifi/pcie/drv.c
To solve this drop these three lines from the conflict (the first hunk
from "HEAD") as the whole AX200 block was moved above in the same
file:
IWL_DEV_INFO(0x2723, 0x1653, iwl_ax200_cfg_cc, iwl_ax200_killer_1650w_name),
IWL_DEV_INFO(0x2723, 0x1654, iwl_ax200_cfg_cc, iwl_ax200_killer_1650x_name),
IWL_DEV_INFO(0x2723, IWL_CFG_ANY, iwl_ax200_cfg_cc, iwl_ax200_name),
And keep all the __IWL_DEV_INFO() entries (the second hunk). In other
words, take everything from wireless-drivers-next. When running 'git
diff' after the resolution the output should be empty.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is used to initialize the default value, but refers back
to the value itself, essentially leading to a
val = val
assignment at init time ... that's useless, remove it and use
_NODEF.
Change-Id: I725923016563c34ce2fa057bf7c12984e1041c49
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The FW changed the maximum number of scan offload profiles to 8 in new
APIs. Support it by changing the scan_offload_profile_cfg struct to be
more dynamic, so we can reuse most of the code and only change size of
the profiles array.
Change-Id: I65210cf541af46e2675a8c764d5871f7f5b070d6
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we have an assert during D3 we want to dump the internal
buffer memory even if are we working in DRAM debug mode. We should not
block dumping it.
Change-Id: I69aad2d4904c4f8bb653c61e8781a2e07780054f
Signed-off-by: Rotem Saado <rotem.saado@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This new command is mostly backwards compatible, with the exception
that the device_type element was changed into a bitmask. The device
type bit remains the same (because we only had 0 and 1 anyway), but
when using v1 we can't set any other bits, because that would change
the integer.
Other than that, the struct remains the same and the driver can set
the device_type bit in both cases, but it can only set the low_latency
bit if VER_2 is used.
Change-Id: Ib68d4c821ebcce253b42ed0ea15881fb4e3e01da
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Modify adaptive dwell number of APs override API
Instead of using channel to index mapping, add the adaptive dwell
override parameters as part of the configuration per channel in the scan
request command.
Support 2 different override values and use them as follows:
1. 10 APs for friendly GO channels in p2p scan.
2. 2 APs for social channels in p2p scan.
Change-Id: I3b461108abf2306c3d054099112f2c3afce1cc92
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a new region type that allows us to dump the PCI config space.
This is mostly the same as dumping a memory region, but reading from
the device's config space instead.
In order to make this generic and independent of the trans type, we
make a function called iwl_dump_ini_config_iter() that calls a new op
in the transport to read its config space.
Change-Id: I15151bddf589f13b0e0a45c28b96bbcd73bcfdeb
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some devices require longer time to stabilize the power and XTAL.
This is especially true for devices integrated in the SoC. Add
support for a new firmware API that allows the driver to set the
latency value accordingly.
Change-Id: I6829a46b89e4e701f80a0e4033f4dd41ee44ed12
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The GEO_TX_POWER_LIMIT command was sent although
there is no wgds table, so the fw got wrong SAR values
from the driver.
Fix this by avoiding sending the command if no wgds
tables are available.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Fixes: 39c1a9728f ("iwlwifi: refactor the SAR tables from mvm to acpi")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Tested-By: Jonathan McDowell <noodles@earth.li>
Tested-by: Len Brown <len.brown@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20200318081237.46db40617cc6.Id5cf852ec8c5dbf20ba86bad7b165a0c828f8b2e@changeid
If the firmware is in a bad state or not initialized fully, sending
the DBGC_SUSPEND_RESUME command fails but we can still collect logs.
Instead of aborting the entire dump process, simply ignore the error.
By removing the last callpoint that was checking the return value, we
can also convert the function to return void.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: 576058330f ("iwlwifi: dbg: support debug recording suspend resume command")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.dcec37b2efd4.I8dcd190431d110a6a0e88095ce93591ccfb3d78d@changeid
The TLV offset is only used to read registers, while the offset used for
the FIFO addresses are hard coded in the driver and not given by the
TLV.
If we try to apply the TLV offset when reading the FIFOs, we'll read
from invalid addresses, causing the driver to hang.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: 8d7dea25ad ("iwlwifi: dbg_ini: implement Rx fifos dump")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200306151129.fbab869c26fa.I4ddac20d02f9bce41855a816aa6855c89bc3874e@changeid
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeLcWsAAoJEG4XJFUm622bDGUIAJuhM4LiDAzOGnDjH5cMosOC
/qwDpGD19cEeVAhNSMKUn7Uo9+qbQYIleiO7XXxzCuJceYbxbT5s3Vb/fWsRUPjS
cBDmGuK8/giqMQJshXvfCTsoF83CyirCjY/MJvomK2BRlXM8hQ3s6hAcfU0zQ96e
OU1akcfZzUwjaBKaDYLncxLuGbeUXMy8AZwFdgQlQRMoObpen/IIwx6jDK/A+3l6
VCOJF+JTkDytfNWmTpZ65uJrYEXoLe6G4028FjOI4BDFmEgvdHC5vTm7VOBhrkuB
9tsKcYNvECCNn2WI96V+etD8kaZPscQIW8hgOrYyGxw43lJg5zH4Z9eWAmHojxE=
=UOhb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We have a lot of mostly duplicated data structures that are repeated
only because the device name string is different. To avoid this, move
the string from the cfg to the trans structure and add it
independently from the rest of the configuration to the PCI mapping
tables.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We have many different firmware images with the same version,
and it's sometimes cumbersome to figure out which image was
really used, especially as the marketing strings that we do
print out can be the same for (slightly) different hardware
using different firmware images.
Incorporate the firmware filename into the fw_version so it's
printed out all the time. Unfortunately, this will make the
string be longer than the 32 characters for ethtool, but we
almost never really use ethtool, so strip the "iwlwifi-"
prefix (if not overridden), and the remaining data that may
then be stripped at the end is not usually useful anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we don't have dynamically changing domains anymore, we can
simply skip all the TLVs with domains that are not enabled. To do so,
remove the checks from the functions that handle the TLVs when a
timepoint is reached to the top allocation function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that we can't change the domain at runtime anymore, we don't have
to protect the active trigger status. Remove it. Additionally, we
don't need to flush the dumps at this point anymore, since this only
runs during initialization and there shouldn't be any dumps running.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't want to allow changing the domain via debugfs so that we can
apply the domain to all TLV types more easily (doing some at runtime
is difficult due to buffer allocations etc.). Change the
fw_dbg_domain debugfs file to be read-only and remove the write
function.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API version adds support for FILS discovery frames.
It adds a new flag and a field for short SSID configuration.
The new API is backward compatible, so we can just switch to it.
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the for loop where we are supposed to go through the entire table,
we are using a non-static local to keep the pos index. This makes
each iteration start with 3, so we always access the first item on the
table. Fix this by moving the variable outside of the loo so it
doesn't lose its value at every iteration.
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fixes: ba3224db78 ("iwlwifi: mvm: fix an out-of-bound access")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver is required to stop the debug monitor HW recording regardless
of the debug configuration since the driver is responsible to halt the
FW DBGC.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API requires the driver to config the supported frame format
(legacy, HT, VHT etc.).
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The new API requires the driver to set the frame format
(legacy, HT, VHT etc.) to be used for the measurement.
The new API also supports 11az and secured measurement, but
these are not supported by the driver for now.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The fw already support scan api v12,
v11 is not needed anymore.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Before we start looping over the internal TX FIFOs increase the fifo
number, but that's incorrect and causes a FIFO to be skipped. This is
probably due to a copy and paste from the previous loop.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
1. Modify channel config flags to be used for legacy bands channels
as well, to indicate SSIDs elements from ssidIEsArray.
2. Add new general flag.
3. Remove ssidNum from probe params.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware API has changed a little bit but this change
has no impact on the flow and is backward compatible.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Refactored the SAR related functions from iwlmvm to acpi
in order to make it shared between different opmodes
in addition to removing unused variable ppag_rev.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement scan request command version 12.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
