When we have 256 block-ack support, we may need to be very fast
to provide a lot of frames to the hardware to transmit, but that
cannot be guaranteed. Use a longer queue size to have more time,
and the next possible queue size is 1024 since it must be a power
of two.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.851866c7e4c4.I13fa678929431f1694fd202c1da40aa476ab70fe@changeid
The hardware needs a byte-count table with the size of each frame
on the queue to build A-MPDUs, but:
* newer generation no longer have the duplicated space at the end,
they can deal with the wrap properly - and we don't even fill
the dup anyway
* we have a maximum queue size of 512 right now and don't use the
theoretical hardware maximum of 65536.
Together, this reduces the byte count table DMA allocation from
64KiB (65536*2 + 64*2 rounded up) to 1 KiB (though that might be
rounded up to a full 4 KiB page by the allocator, not sure it can
share the allocations.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200425130140.c263b787b5ab.I059507a9760b1ce1d45d84dcaa91629a5cfb58e0@changeid
For HE-capable devices, we need to allocate more receive buffers as
there could be 256 frames aggregated into a single A-MPDU, and then
they might contain A-MSDUs as well. Until 22000 family, the devices
are able to put multiple frames into a single RB and the default RB
size is 4k, but starting from AX210 family this is no longer true.
On the other hand, those newer devices only use 2k receive buffers
(by default).
Modify the code and configuration to allocate an appropriate number
of RBs depending on the device capabilities:
* 4096 for AX210 HE devices, which use 2k buffers by default,
* 2048 for 22000 family devices which use 4k buffers by default,
* 512 for existing 9000 family devices, which doesn't really
change anything since that's the default before this patch,
* 512 also for AX210/22000 family devices that don't do HE.
Theoretically, for devices lower than AX210, we wouldn't have to
allocate that many RBs if the RB size was manually increased, but
to support that the code got more complex, and it didn't really
seem necessary as that's a use case for monitor mode only, where
hopefully the wasted memory isn't really much of a concern.
Note that AX210 devices actually support bigger than 12-bit VID,
which is required here as we want to allocate 4096 buffers plus
some for quick recycling, so adjust the code for that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This is dead code, nothing uses the IWL_DEVICE_22560 macro and
thus nothing every uses IWL_DEVICE_FAMILY_22560. Remove it all.
While at it, remove some code and definitions used only in this
case, and clean up some comments/names that still refer to it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fix various misspellings of "configuration" and "configure".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Some variables are used in iwl-fh.h, but their type's definition
isn't included. This may break compilation when using the file
without including the necessary dependencies first.
Add the required include to iwl-fh.h.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22560 devices the firmware will do all the hw configurations,
but that's not ready yet.
Update the correct registers in the driver until the FW is ready
and does it by itself.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22560 devices tfd queue max size is 2^16. Allow a configurable
max size in the driver for supporting different devices.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The family name A000 was just a place-holder when we didn't know what
the official name would be yet. Now we know that the family name is
22000, so rename all occurrences accordingly.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Properly document the transmit buffer bits using an enum and
kernel-doc documentation.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Letting the preprocessor/compiler generate the shift/mask by itself
is a win for readability, so use bitfield.h for some registers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FH in A000 HW are placed in a different location,
and need to be read as prph, rather than direct.
Support A000 dumping as well as legacy.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Context information structure is going to be used in a000
devices for firmware self init.
The self init includes firmware self loading from DRAM by
ROM.
This means the TFH relevant firmware loading can be cleaned up.
The firmware loading includes the paging memory as well, so op
mode can stop initializing the paging and sending the DRAM_BLOCK_CMD.
Firmware is doing RFH, TFH and SCD configuration, while driver
only fills the required configurations and addresses in the
context information structure.
The only remaining access to RFH is the write pointer, which
is updated upon alive interrupt after FW configured the RFH.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Since TFD was enlarged to 256 bytes, the fetch of the TFD
itself is very expensive.
To make DRAM to SRAM more efficient, bits 12-13 will indicate
the number of 64 byte chunks that should be transferred to
SRAM.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New hardware supports bigger TFDs and TBs.
Introduce the new formats and adjust defines and code
relying on old format.
Changing the actual TFD allocation is trickier and
deferred to the next patch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Turns out we should access TFH relative addresses.
Also, the FH_UCODE_LOAD_STATUS was replaced by
UREG_UCODE_LOAD_STATUS.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 device the FH was replaced by the TFH.
This is the first patch in a series introducing the
changes stemming from this change.
This patch initializes the TFQ queue table with the new
64 bit register and the relevant TFH configuration
registers.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Somehow we ended up stopping RX using legacy RX registers
even for devices that support RFH. Fix it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For 9000 devices we can have PCIe bus for discrete
devices and IOSF bus for integrated devices.
PCIe supports maximum transfer size of 128B while IOSF
bus supports maximum transfer size of 64B.
Configure RB size accordingly.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The RX queues have a shadow register for the write pointer
that enables updates without grabbing NIC access. Use them
instead of the periphery registers because accessing those
is much more expensive.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We kick the allocator when we have 2 RBDs that don't have
attached RBs, and the allocator allocates 8 RBs meaning
that it needs another 6 RBDs to attach the RBs to.
The design is that allocator should always have enough RBDs
to fulfill requests, so we give in advance 6 RBDs to the
allocator so that when it is kicked, it gets additional 2 RBDs
and has enough RBDs.
These RBDs were taken from the Rx queue itself, meaning
that each Rx queue didn't have the maximal number of
RBDs, but MAX - 6.
Change initial number of RBDs in the system to include both
queue size and allocator reserves.
Note the multi-queue is always 511 instead of 512 to avoid a
full queue since we cannot detect this state easily enough in
the 9000 arch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fine tune RFH registers further:
* Set default queue explicitly
* Set RFH to drop frames exceeding RB size
* Set the maximum rx transfer size to DRAM to 128 instead of 64
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The 9000 series introduces several changes in the device
DMA operation.
As the device now supports multi-queue rx, several DMA channels
should be configured.
The flows of providing the device with the allocated RBDs now
changes as well - the device maintains a separate table of used
and free table.
The hardware may use the free table to feed RBDs to any queue.
This requires maintaing a shared table to map returned RBDs to
the original RXB - for that purpose the VID is introduced - an
internal identifier of the RB placed in the lower 12 bits and
returned by HW in the used data.
Another change is the support of 64 bit DMA address.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
ilw@linux.intel.com is not available anymore.
linuxwifi@intel.com should be used instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
