When a frame was acked and probe frames were sent, the connection monitoring
needs to be reset, otherwise it will keep probing until the connection is
considered dead, even though frames have been acked in the mean time.
Fixes: 9abf4e4983 ("mac80211: optimize station connection monitor")
Reported-by: Georgi Valkov <gvalkov@abv.bg>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200927105605.97954-1-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Recently channels gained a potential frequency offset, so
include this in the per-channel survey info.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-16-thomas@adapt-ip.com
[add the offset only if non-zero]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The changes required for associating in S1G are:
- apply S1G BSS channel info before assoc
- mark all S1G STAs as QoS STAs
- include and parse AID request element
- handle new Association Response format
- don't fail assoc if supported rates element is missing
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-15-thomas@adapt-ip.com
[pass skb to ieee80211_add_aid_request_ie(), remove unused variable 'bss']
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G beacons are 802.11 Extension Frames, so the fixed
header part differs from regular beacons.
Add a handler to process S1G beacons and abstract out the
fetching of BSSID and element start locations in the
beacon body handler.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-14-thomas@adapt-ip.com
[don't rename, small coding style cleanups]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
minstrel_ht is confused by the lack of sband->bitrates,
and S1G will likely require a unique RC algorithm, so
avoid rate init for now if STA is on the S1G band.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-13-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G doesn't have legacy (sband->bitrates) rates, only MCS.
For now, just send a frame at MCS 0 if a low rate is
requested. Note we also redefine (since we're out of TX
flags) TX_RC_VHT_MCS as TX_RC_S1G_MCS to indicate an S1G
MCS. This is probably OK as VHT MCS is not valid on S1G
band and vice versa.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-12-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now just skip the duration calculation for frames
transmitted on the S1G band and avoid a warning.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-11-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
S1G allows listen interval up to 2^14 * 10000 beacon
intervals. In order to do this listen interval needs a
scaling factor applied to the lower 14 bits. Calculate
this and properly encode the listen interval for S1G STAs.
See IEEE802.11ah-2016 Table 9-44a for reference.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-10-thomas@adapt-ip.com
[move listen_int_usf into function using it]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The sending STA type is implicit based on beacon or probe
response content. If sending STA was an S1G STA, adjust
the Information Element location accordingly.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-9-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This commit finds the correct offset for Information
Elements in S1G beacon frames so they can be reported in
scan results.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-8-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The S1G beacon is an extension frame as opposed to
management frame for the regular beacon. This means we may
have to occasionally cast the frame buffer to a different
header type. Luckily this isn't too bad as scan results
mostly only care about the IEs.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-6-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Include the S1G Capabilities element in an association
request, and support the cfg80211 capability overrides.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-5-thomas@adapt-ip.com
[pass skb to ieee80211_add_s1g_capab_ie(), small code style edits]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
NL80211_ATTR_S1G_CAPABILITY can be passed along with
NL80211_ATTR_S1G_CAPABILITY_MASK to NL80211_CMD_ASSOCIATE
to indicate S1G capabilities which should override the
hardware capabilities in eg. the association request.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-4-thomas@adapt-ip.com
[johannes: always require both attributes together, commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
An S1G BSS can beacon at either 1 or 2 MHz and the channel
width is unique to a given frequency. Ignore scan channel
width for now and use the allowed channel width.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-3-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When deleting a channel context, mac80211 would assing
NL80211_CHAN_WIDTH_20_NOHT as the default channel width.
This is wrong in S1G however, so instead get the allowed
channel width for a given channel.
Fixes eg. configuring strange (20Mhz) width during a scan
on the S1G band.
Signed-off-by: Thomas Pedersen <thomas@adapt-ip.com>
Link: https://lore.kernel.org/r/20200922022818.15855-2-thomas@adapt-ip.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Support 6 GHz scanning, by
* a new scan flag to scan for colocated BSSes advertised
by (and found) APs on 2.4 & 5 GHz
* doing the necessary reduced neighbor report parsing for
this, to find them
* adding the ability to split the scan request in case the
device by itself cannot support this.
Also add some necessary bits in mac80211 to not break with
these changes.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Link: https://lore.kernel.org/r/20200918113313.232917c93af9.Ida22f0212f9122f47094d81659e879a50434a6a2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Because we can miss AP wakeup (beacon) while scanning other channels,
it's better go into wakeup state and inform the AP of that upon
returning to the operating channel, rather than staying asleep and
waiting for the next TIM indicating traffic for us.
This saves precious time, especially when we only have 200ms inter-
scan period for monitoring the active connection.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Link: https://lore.kernel.org/r/1593420923-26668-1-git-send-email-loic.poulain@linaro.org
[rewrite commit message a bit]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
After commit d0186842ec ("net: vlan: Avoid using BUG() in
vlan_proto_idx()"), vlan_proto_idx() was changed to return a signed
integer, however one of its called: vlan_group_prealloc_vid() was still
using an unsigned integer for its return value, fix that.
Fixes: d0186842ec ("net: vlan: Avoid using BUG() in vlan_proto_idx()")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Mauri Sandberg <sandberg@mailfence.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sja1105 is a bit of a special snowflake, in that not all frames are
transmitted/received in the same way. L2 link-local frames are received
with the source port/switch ID information put in the destination MAC
address. For the rest, a tag_8021q header is used. So only the latter
frames displace the rest of the headers and need to use the generic flow
dissector procedure.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: John Crispin <john@phrozen.org>
Cc: Alexander Lobakin <alobakin@pm.me>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: DENG Qingfang <dqfext@gmail.com>
Cc: Sean Wang <sean.wang@mediatek.com>
Cc: John Crispin <john@phrozen.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove the .flow_dissect procedure, so the flow dissector will call the
generic variant which works for this tagging protocol.
Cc: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 Broadcom tags in use, one places the DSA tag before the
Ethernet destination MAC address, and the other before the EtherType.
Nonetheless, both displace the rest of the headers, so this tagger can
use the generic flow dissector procedure which accounts for that.
The ASCII art drawing is a good reference though, so keep it but move it
somewhere else.
Cc: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the recent mitigations against speculative execution exploits,
indirect function calls are more expensive and it would be good to avoid
them where possible.
In the case of DSA, most switch taggers will shift the EtherType and
next headers by a fixed amount equal to that tag's length in bytes.
So we can use a generic procedure to determine that, without calling
into custom tagger code. However we still leave the flow_dissect method
inside struct dsa_device_ops as an override for the generic function.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Marvell 88E6060 uses tag_trailer.c and the KSZ8795, KSZ9477 and
KSZ9893 switches also use tail tags.
Tell that to the DSA core, since this makes a difference for the flow
dissector. Most switches break the parsing of frame headers, but these
ones don't, so no flow dissector adjustment needs to be done for them.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no tagger that returns anything other than zero, so just change
the return type appropriately.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 goals that we follow:
- Reduce the header size
- Make the header size equal between RX and TX
The issue that required long prefix on RX was the fact that the ocelot
DSA tag, being put before Ethernet as it is, would overlap with the area
that a DSA master uses for RX filtering (destination MAC address
mainly).
Now that we can ask DSA to put the master in promiscuous mode, in theory
we could remove the prefix altogether and call it a day, but it looks
like we can't. Using no prefix on ingress, some packets (such as ICMP)
would be received, while others (such as PTP) would not be received.
This is because the DSA master we use (enetc) triggers parse errors
("MAC rx frame errors") presumably because it sees Ethernet frames with
a bad length. And indeed, when using no prefix, the EtherType (bytes
12-13 of the frame, bits 96-111) falls over the REW_VAL field from the
extraction header, aka the PTP timestamp.
When turning the short (32-bit) prefix on, the EtherType overlaps with
bits 64-79 of the extraction header, which are a reserved area
transmitted as zero by the switch. The packets are not dropped by the
DSA master with a short prefix. Actually, the frames look like this in
tcpdump (below is a PTP frame, with an extra dsa_8021q tag - dadb 0482 -
added by a downstream sja1105).
89:0c:a9:f2:01:00 > 88:80:00:0a:00:1d, 802.3, length 0: LLC, \
dsap Unknown (0x10) Individual, ssap ProWay NM (0x0e) Response, \
ctrl 0x0004: Information, send seq 2, rcv seq 0, \
Flags [Response], length 78
0x0000: 8880 000a 001d 890c a9f2 0100 0000 100f ................
0x0010: 0400 0000 0180 c200 000e 001f 7b63 0248 ............{c.H
0x0020: dadb 0482 88f7 1202 0036 0000 0000 0000 .........6......
0x0030: 0000 0000 0000 0000 0000 001f 7bff fe63 ............{..c
0x0040: 0248 0001 1f81 0500 0000 0000 0000 0000 .H..............
0x0050: 0000 0000 0000 0000 0000 0000 ............
So the short prefix is our new default: we've shortened our RX frames by
12 octets, increased TX by 4, and headers are now equal between RX and
TX. Note that we still need promiscuous mode for the DSA master to not
drop it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently PTP is broken when ports are in standalone mode (the tagger
keeps printing this message):
sja1105 spi0.1: Expected meta frame, is 01-80-c2-00-00-0e in the DSA master multicast filter?
Sure, one might say "simply add 01-80-c2-00-00-0e to the master's RX
filter" but things become more complicated because:
- Actually all frames in the 01-80-c2-xx-xx-xx and 01-1b-19-xx-xx-xx
range are trapped to the CPU automatically
- The switch mangles bytes 3 and 4 of the MAC address via the incl_srcpt
("include source port [in the DMAC]") option, which is how source port
and switch id identification is done for link-local traffic on RX. But
this means that an address installed to the RX filter would, at the
end of the day, not correspond to the final address seen by the DSA
master.
Assume RX filtering lists on DSA masters are typically too small to
include all necessary addresses for PTP to work properly on sja1105, and
just request promiscuous mode unconditionally.
Just an example:
Assuming the following addresses are trapped to the CPU:
01-80-c2-00-00-00 to 01-80-c2-00-00-ff
01-1b-19-00-00-00 to 01-1b-19-00-00-ff
These are 512 addresses.
Now let's say this is a board with 3 switches, and 4 ports per switch.
The 512 addresses become 6144 addresses that must be managed by the DSA
master's RX filtering lists.
This may be refined in the future, but for now, it is simply not worth
it to add the additional addresses to the master's RX filter, so simply
request it to become promiscuous as soon as the driver probes.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently DSA assumes that taggers don't mess with the destination MAC
address of the frames on RX. That is not always the case. Some DSA
headers are placed before the Ethernet header (ocelot), and others
simply mangle random bytes from the destination MAC address (sja1105
with its incl_srcpt option).
Currently the DSA master goes to promiscuous mode automatically when the
slave devices go too (such as when enslaved to a bridge), but in
standalone mode this is a problem that needs to be dealt with.
So give drivers the possibility to signal that their tagging protocol
will get randomly dropped otherwise, and let DSA deal with fixing that.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Sections of device flash may contain settings or device identifying
information. When performing a flash update, it is generally expected
that these settings and identifiers are not overwritten.
However, it may sometimes be useful to allow overwriting these fields
when performing a flash update. Some examples include, 1) customizing
the initial device config on first programming, such as overwriting
default device identifying information, or 2) reverting a device
configuration to known good state provided in the new firmware image, or
3) in case it is suspected that current firmware logic for managing the
preservation of fields during an update is broken.
Although some devices are able to completely separate these types of
settings and fields into separate components, this is not true for all
hardware.
To support controlling this behavior, a new
DEVLINK_ATTR_FLASH_UPDATE_OVERWRITE_MASK is defined. This is an
nla_bitfield32 which will define what subset of fields in a component
should be overwritten during an update.
If no bits are specified, or of the overwrite mask is not provided, then
an update should not overwrite anything, and should maintain the
settings and identifiers as they are in the previous image.
If the overwrite mask has the DEVLINK_FLASH_OVERWRITE_SETTINGS bit set,
then the device should be configured to overwrite any of the settings in
the requested component with settings found in the provided image.
Similarly, if the DEVLINK_FLASH_OVERWRITE_IDENTIFIERS bit is set, the
device should be configured to overwrite any device identifiers in the
requested component with the identifiers from the image.
Multiple overwrite modes may be combined to indicate that a combination
of the set of fields that should be overwritten.
Drivers which support the new overwrite mask must set the
DEVLINK_SUPPORT_FLASH_UPDATE_OVERWRITE_MASK in the
supported_flash_update_params field of their devlink_ops.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The devlink core recently gained support for checking whether the driver
supports a flash_update parameter, via `supported_flash_update_params`.
However, parameters are specified as function arguments. Adding a new
parameter still requires modifying the signature of the .flash_update
callback in all drivers.
Convert the .flash_update function to take a new `struct
devlink_flash_update_params` instead. By using this structure, and the
`supported_flash_update_params` bit field, a new parameter to
flash_update can be added without requiring modification to existing
drivers.
As before, all parameters except file_name will require driver opt-in.
Because file_name is a necessary field to for the flash_update to make
sense, no "SUPPORTED" bitflag is provided and it is always considered
valid. All future additional parameters will require a new bit in the
supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When implementing .flash_update, drivers which do not support
per-component update are manually checking the component parameter to
verify that it is NULL. Without this check, the driver might accept an
update request with a component specified even though it will not honor
such a request.
Instead of having each driver check this, move the logic into
net/core/devlink.c, and use a new `supported_flash_update_params` field
in the devlink_ops. Drivers which will support per-component update must
now specify this by setting DEVLINK_SUPPORT_FLASH_UPDATE_COMPONENT in
the supported_flash_update_params in their devlink_ops.
This helps ensure that drivers do not forget to check for a NULL
component if they do not support per-component update. This also enables
a slightly better error message by enabling the core stack to set the
netlink bad attribute message to indicate precisely the unsupported
attribute in the message.
Going forward, any new additional parameter to flash update will require
a bit in the supported_flash_update_params bitfield.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Cc: Jiri Pirko <jiri@mellanox.com>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Bin Luo <luobin9@huawei.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: Ido Schimmel <idosch@mellanox.com>
Cc: Danielle Ratson <danieller@mellanox.com>
Cc: Shannon Nelson <snelson@pensando.io>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_skb_mark_lost is used by RFC6675-SACK and can easily be replaced
with the new tcp_mark_skb_lost handler.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates and simplifes the loss marking logic used
by a few loss detections (RACK, RFC6675, NewReno). Previously
each detection uses a subset of several intertwined subroutines.
This unncessary complexity has led to bugs (and fixes of bug fixes).
tcp_mark_skb_lost now is the single one routine to mark a packet loss
when a loss detection caller deems an skb ist lost:
1. rewind tp->retransmit_hint_skb if skb has lower sequence or
all lost ones have been retransmitted.
2. book-keeping: adjust flags and counts depending on if skb was
retransmitted or not.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A pure refactor to move tcp_mark_skb_lost to tcp_input.c to prepare
for the later loss marking consolidation.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_simple_retransmit() used for path MTU discovery may not adjust
the retransmit hint properly by deducting retrans_out before checking
it to adjust the hint. This patch fixes this by a correct routine
tcp_mark_skb_lost() already used by the RACK loss detection.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should remove a group from the sg_port hash only if it's an S,G
entry. This makes it correct and more symmetric with group add. Also
since *,G groups are not added to that hash we can hide a bug.
Fixes: 085b53c8be ("net: bridge: mcast: add sg_port rhashtable")
Signed-off-by: Nikolay Aleksandrov <nikolay@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Is it just me, or is the logic written in a slightly convoluted way?
I find it a little easier to read this way.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
seq_puts is a lot cheaper than seq_printf, so use that to print
literal strings.
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Reserving space for a large READ payload requires special handling when
reserving space in the xdr buffer pages. One problem we can have is use
of the scratch buffer, which is used to get a pointer to a contiguous
region of data up to PAGE_SIZE. When using the scratch buffer, calls to
xdr_commit_encode() shift the data to it's proper alignment in the xdr
buffer. If we've reserved several pages in a vector, then this could
potentially invalidate earlier pointers and result in incorrect READ
data being sent to the client.
I get around this by looking at the amount of space left in the current
page, and never reserve more than that for each entry in the read
vector. This lets us place data directly where it needs to go in the
buffer pages.
Signed-off-by: Anna Schumaker <Anna.Schumaker@Netapp.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Drop duplicate words in net/sunrpc/.
Also fix "Anyone" to be "Any one".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: linux-nfs@vger.kernel.org
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
While we should always make sure that we specify a valid VLAN protocol
to vlan_proto_idx(), killing the machine when an invalid value is
specified is too harsh and not helpful for debugging. All callers are
capable of dealing with an error returned by vlan_proto_idx() so check
the index value and propagate it accordingly.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the bpf_sk_assign() to take
ARG_PTR_TO_BTF_ID_SOCK_COMMON such that they will work with the pointer
returned by the bpf_skc_to_*() helpers also.
The bpf_sk_lookup_assign() is taking ARG_PTR_TO_SOCKET_"OR_NULL". Meaning
it specifically takes a literal NULL. ARG_PTR_TO_BTF_ID_SOCK_COMMON
does not allow a literal NULL, so another ARG type is required
for this purpose and another follow-up patch can be used if
there is such need.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200925000415.3857374-1-kafai@fb.com
This patch changes the bpf_tcp_*_syncookie() to take
ARG_PTR_TO_BTF_ID_SOCK_COMMON such that they will work with the pointer
returned by the bpf_skc_to_*() helpers also.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20200925000409.3856725-1-kafai@fb.com
This patch changes the bpf_sk_storage_*() to take
ARG_PTR_TO_BTF_ID_SOCK_COMMON such that they will work with the pointer
returned by the bpf_skc_to_*() helpers also.
A micro benchmark has been done on a "cgroup_skb/egress" bpf program
which does a bpf_sk_storage_get(). It was driven by netperf doing
a 4096 connected UDP_STREAM test with 64bytes packet.
The stats from "kernel.bpf_stats_enabled" shows no meaningful difference.
The sk_storage_get_btf_proto, sk_storage_delete_btf_proto,
btf_sk_storage_get_proto, and btf_sk_storage_delete_proto are
no longer needed, so they are removed.
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenz Bauer <lmb@cloudflare.com>
Link: https://lore.kernel.org/bpf/20200925000402.3856307-1-kafai@fb.com
