[Why]
When an riommu invalidation request come at the same time as a pipe is
disabled there can be a case where DCN cannot ACK the request if only
one VMID is setup in the inuse list.
[How]
Setup a second unused VMID will work around the issue.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
DCN 3x increased Line buffer size for DCHUB latency hiding, from 4 lines
of 4K resolution lines to 5 lines of 4K resolution lines. All Line
Buffer can be used as extended memory for P State change latency hiding.
The maximum number of lines is increased to 32 lines. Finally,
LB_MEMORY_CONFIG_1 (LB memory piece 1) and LB_MEMORY _CONFIG_2 (LB
memory piece 2) are not affected, no change in size, only 3 pieces is
affected, i.e., when all 3 pieces are used in both LB_MEMORY_CONFIG_0
and LB_MEMORY_CONFIG_3 (for 4:2:0) modes.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
During S4/S5/reboot, sometimes riommu invalidation request arrive too
early, DCN may be unable to respond to the invalidation request
resulting in pstate hang.
[How]
VBIOS will force allow pstate for riommu invalidation and driver will
clear it after powering down display pipes.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Extend existing state collection functions to add some additional
registers useful for debug, and add state collection function for DC
hubbub
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When requesting clocks from SMU which takes MHz inputs, DC will round
down KHz when converting to MHz, thus potentially requesting too low a
clock value.
[How]
Round up (ceil) when converting KHz to MHz for clock requests to SMU.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a difference between our default behavior and override
behavior. For default behavior we need to decide link training settings
within specs' limitation and mandates.
For override behavior we do not need to follow all these requirements.
We are isolating override decision to its own function to maintain the
integrity of our specs compliant default behavior.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Hardware has handed down a new sequence requiring the value of this
register be read from clk_mgr.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Some DPCD addresses, notably LTTPR Capability registers, are expected to
be read all together in a single DPCD transaction. Rather than force callers to
read registers they don't need, we want to quietly extend the addresses
read, and only return back the values the caller asked for.
This does not affect DPCD writes.
[HOW]
Create an additional layer above AUX to perform 'checked' DPCD
transactions.
Iterate through an array of DPCD address ranges that are marked as being
contiguous. If a requested read falls within one of those ranges, extend
the read to include the entire range.
After DPCD has been queried, copy the requested bytes into the caller's
data buffer, and deallocate all resources used.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
SCR for DP 2.0 requires that LTTPR caps be read first on hotplug.
For the sake of consistency, this should also be the case on bootup.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Move mst start top mgr in dc_link_detect layer.
Remove unused same_dpcd variable.
Move PEAK_FACTOR_X1000 and LINK_TRAINING_MAX_VERIFY_RETRY
to the proper header for defining dc link internal constant.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support a new visual confirm mode: swizzle to show the specific
color at the screen border according to different surface swizzle mode.
Currently we only support the Linear mode with red color.
Signed-off-by: Po-Ting Chen <robin.chen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence that requires access to these
registers.
v2: squash in DCN3.1 fixes (Alex)
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HW has handed down a new sequence which requires access to the FIFO
ERRDET SW Override register.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How]
Add call to get the last used VTOTAL from DC
Signed-off-by: Jayendran Ramani <Jayendran.Ramani@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP equalization phase of link training to
public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why + How]
Visual confirm has no asic-specific logic,
so we can refactor and unify these functions
that are currently spread out across multiple
dcn files.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
This will allow visual confirm to updated independently
of MPCC blending updates.
v2: squash in DCN3.1 fixes
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add DCN3.1 specific hardware sequence programming - extending off of
our existing DCN3/DCN2 support.
Extend stream hardware sequencing to include new DCCG programming.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for programming the DCN3.1 OPTC (Output Timing Controller)
HW Blocks:
+--------+
| MPC |
+--------+
|
v
+-------+
| OPP |
+-------+
|
v
+--------+
| OPTC |
+--------+
|
v
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
There are no changes to OPP or MPC for DCN3.1, so the diagram will
include them in this patch.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support for the DIO (Display IO) block of DCN3.1 which controls
legacy HDMI/DP stream/link encoding.
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Includes some updates to core logic for link encoder assignment and
future support for new high bandwidth output.
v2: squash in unused variable fix (Alex)
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for clock requests for the various parts of the DCN3.1 IP
and the interfaces and definitions for sending messages to SMU/PMFW.
Includes new support for z9/10, detecting SMU timeout and p-state
support enablement.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit 3ca402375a.
Recent visual confirm changes are regressing the driver, causing a
black screen on boot in some green sardine configs, or visual confirm
is not updated at all.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two issues with scaling calculations, odm recout
calculation and matching viewport to actual recout.
This change fixes both issues. Odm recout calculation via
special casing and viewport matching issue by reworking
the viewport calcualtion to use scaling ratios and recout
to derrive the required offset and size.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP clock recovery phase of link training to
public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
- Update application of training settings for links whose encoders are
assigned dynamically.
- Add functionality useful for DP link configuration to public
interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Added support for individual control for multiple back-light instances.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Conditions that end up modifying the global dc state must be locked.
However, during mst allocate payload sequence, lock is already taken.
With StarTech 1.2 DP hub, we get an HPD RX interrupt for a reason other
than to indicate down reply availability right after sending payload
allocation. The handler again takes dc lock before calling the
dc's HPD RX handler. Due to this contention, the DRM thread which waits
for MST down reply never gets a chance to finish its waiting
successfully and ends up timing out. Once the lock is released, the hpd
rx handler fires and goes ahead to read from the MST HUB, but now its
too late and the HUB doesnt lightup all displays since DRM lacks error
handling when payload allocation fails.
[How]
Take lock only if there is a change in link status or if automated test
pattern bit is set. The latter fixes the null pointer dereference when
running certain DP Link Layer Compliance test.
Fixes: c8ea79a8a2 ("drm/amd/display: NULL pointer error during compliance test")
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Visual confirm will indicate if driver is programming
the surface address.
Refactor is required because much of the visual confirm
logic is buried deep in the mpcc files.
In addition, visual confirm is not updated during fast updates.
[How]
In order to have visual confirm for driver flips, visual confirm
needs to be updated on every frame, including fast updates.
Add a new hw sequencer interface update_visual_confirm_color,
and a new mpc function pointer set_bg_color.
v2: drop unused variable (Alex)
Signed-off-by: Wyatt Wood <wyatt.wood@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[how]
Implement a function that determines link encoding format
based on the link settings passed in.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
During the investigation on how to add visual confirmation on top of the
planes used by DCN, it becomes evident that the lack of information in
the code makes this work unnecessarily complicated. This commit
introduces a set of documentation related to the RECOUT operation in
order to make it easy for developers to navigate this set of functions.
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add functionality useful for DP link training to public interface.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling a DisplayPort stream:
- Optionally reducing link bandwidth between failed link training
attempts should progressively relax training requirements.
- Abandoning link training altogether if a sink is unplugged should
avoid unnecessary training attempts.
[How]
- Add fallback parameter to DP link training function and reduce link
bandwidth between failed training attempts as long as stream bandwidth
requirements are met.
- Add training status for sink unplug and abort training when this
status is reported.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some links are dynamically assigned link encoders on stream enablement.
[How]
Update DisplayPort training parameter determination stage that assumes
link encoder statically assigned to link.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Per DP spec, for active protocol convertor adaptor, DP source should enable audio
for DFP type is DP, HDMI or DP++. Current is_dp_active_dongle() checking is not
precise, which treat branch device default as active dongle. As a result, we will
mistakenly disable audio for DFP type is DP case.
[How]
Make is_dp_active_dongle() checking more precise for active dongle types.
Rename active diongle type as SST branch device in case confusion.
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Based on hardware team recommendation this additional dsc overhead
is only required for DP DSC.
[how]
Add a check for is_dp and only apply the overhead if this flag is set.
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DSC is enabled before reset link and potentially cause DSC enable fail problem.
[How]
Enable DSC after link is reseted
Signed-off-by: Mike Hsieh <chun-wei.hsieh@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
VBIOS currently sets the max link rate found in eDP 1.4 SUPPORTED_LINK_RATES table
If eDP fastboot optimizations are enabled, the link rate remains at max after init
[How]
Determine optimal link rate during boot, disable seamless boot
and eDP fastboot optimizations if link rate optimization is required
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Currently to view the DCC_EN bit the entire DTN log
must be dumped. A compact method to view the DCC_EN
bit is desirable.
[how]
Introduce new debugfs interface that only dumps the
DCC_EN bit.
Example usage:
cat /sys/kernel/debug/dri/0/amdgpu_dm_dcc_en
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bring-up purpose code to disable DMUB calling into
SMU and timeout for MALL when SMU is not present.
[How]
Disable MALL when SMU is not present.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
There is a bug in HW that causes P-State to hang when DPG is enabled in
certain conditions.
[HOW]
The solution is to force MIN_TTU_VBLANK register to maximum value
whenever DPG has been enabled.
Make stream do a full update on test pattern change, so that the TTUs
get updated.
When DPG is enabled, update the ttu_regs.min_ttu_vblank field of each
pipe in the stream's topology to the maximum value (0xffffff).
v2: squash in build fix for when DCN is not defined (Alex)
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display endpoints may be dynamically mapped to the link encoders
which drive them.
[How]
Update the code paths for display enabling/disabling to accommodate
the dynamic association between links and link encoders.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some display endpoints may be programmably mapped to compatible link
encoders. The assignment of link encoders to links has to be dynamic to
accommodate the increased flexibility in comparison to conventional
display endpoints.
[How]
- Add link encoder assignment tracking variables.
- Execute link encoder assignment algorithm before enabling link and
release link encoders from links once they are disabled.
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Change set_drr to pass in the entire dc_crtc_timing_adjust
structure instead of passing in the parameters individually.
This is to more easily pass in required parameters in the
adjust structure when it gets updated.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The pmfw structs are specific to the asic and should not be
present in base clk_mgr struct
v2: squash in SI fix (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SOC needs to be updated to the WM set A values before validation
happens.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Bernstein <Eric.Bernstein@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
pflip interrupt would not be enabled promptly if a pipe is disabled
and re-enabled, causing flip_done timeout error during DP
compliance tests
[How]
Enable pflip interrupt upon pipe enablement
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>