GCMP MIC length is not filled for GCMP/GCMP-256 cipher suites in
PMF enabled case. Due to mismatch in MIC length, deauth/disassoc frames
are unencrypted.
This patch fills proper MIC length for GCMP/GCMP-256 cipher suites.
Tested HW: QCA9984, QCA9888
Tested FW: 10.4-3.6-00104
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Co-developed-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Sowmiya Sree Elavalagan <ssreeela@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
BTCOEX feature is not supported by all QCA4019 chipsets.
Since btcoex enabled by default in firmware, host needs to
enable COEX support depends on the hardware. Enabling it
by default in unsupported hardware will cause some
feature disabled in hardware.
This patch will read btcoex_support flag and
wlan priority gpio pin number from DT. Depends on the
btcoex_support flag value host will expose BTCOEX support
and wlan priority gpio pin number to target.
Testing:
* Tested HW : QCA4019
* Tested FW : 10.4-3.2.1.1-00017
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
So far, frames were forwarded regardless of the FCS correctness leading
to userspace applications listening on the monitor mode interface to
receive potentially broken frames, even with the "fcsfail" flag unset.
By default, with the "fcsfail" flag of a monitor mode interface
unset, frames with FCS errors should be dropped. With this patch, the
fcsfail flag is taken into account correctly.
Tested-on: QCA4019 firmware-5-ct-full-community-12.bin-lede.011
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For RX, it has two parts, one is to read data from sdio, another
is to indicate the packets to upper stack. Recently it has only
one thread to do all RX things, it results that it is sequential
for RX and low throughout, change RX to parallel for the two parts
will increase throughout.
This patch move the indication to a workqueue, it results in
significant performance improvement on RX path.
Udp rx throughout is 200Mbps without this patch, and it arrives
400Mbps with this patch.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_TLV_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath10k will check the capability, and if it is enabled then
ath10k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath10k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware to enable/disable the radio
and also notifies cfg80211.
We can't power off the device when rfkill is enabled, as otherwise the
firmware would not be able to detect GPIO changes and report them to the
host. So when rfkill is enabled, we need to keep the firmware running.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add vht_supp_mcs argument to service ready structure and print
supported MCS rates in WMI service ready debug message.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add lowest/highest 2ghz channel arguments for use within WMI service
ready structure.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The peer param id for PEER_PARAM_USE_FIXED_PWR
is different for tlv and non-tlv firmware. This
causes incorrect peer param to be set by the driver
to the firmware(tlv/non-tlv).
Create seperate peer param map for tlv and non-tlv
firmware and attach the peer param id based on the
firmware type during the init.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Integrated WiFi chipset ex:WCN399x supports fw logging
using WMI copy engine and shared mem DIAG based fw logging.
By default shared mem DIAG based fw logging is enabled.
To support WMI copy engine based fw logging add QMI
control message to enable WMI copy engine based fw logging.
Enable WMI based fw logging using fw_diag_log module parameter.
insmod ath10k_core.ko fw_diag_log=1
DIAG utility(https://github.com/andersson/diag) implements extraction
of diagnostics related messages between application processor and
various subsystems while shared mem DIAG based fw logging is enabled.
Testing: Tested on WCN3990/QCA6174 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Peer creation in firmware fails if last peer deletion is still
in progress.
The firmware sends a peer delete response event if it advertises
the service WMI_SERVICE_SYNC_DELETE_CMDS. This peer delete response
event is used to synchronize the peer deletion.
Add peer delete response event and wait for the event after
deleting every peer from host driver to synchronize with firmware.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Dundi Raviteja <dundi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we add an interface immediately after removing
the interface the vdev deletion in firmware might not
have been completed. We need to synchronize the vdev creation
with the firmware.
Wait for vdev delete response from firmware when we
remove an interface.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, below fixed rate commands are broken,
iw wlanx set bitrates legacy-<2.4|5> ht-mcs-<2.4|5> vht-mcs-<2.4|5> \
<NSS:MCSx>
iw wlanx set bitrates legacy-<2.4|5> <legacy rate> ht-mcs-<2.4|5> \
vht-mcs-<2.4|5> <NSS:MCSx>
There are two methods to set fixed rate, both failed,
- Use vdev fixed rate command
This command only support one single rate, but it's broken due to
mac80211 change commit e8e4f5280d ("mac80211: reject/clear user
rate mask if not usable"), which requires user to specify at least
one legacy rate. So we can't use this command to set ht/vht single
rate any more.
- Use peer_assoc command
This command can update rx capability for multiple rates, it will
work fine for ht mcs rates, as each supported mcs can be advertised
in ht_mcs index mask. But this will not work with vht rates because,
as per the vht mcs capability advertisement, there are only two bits
to indicate the supported mcs. E.g. only support 0-7, 0-8, 0-9.
So introduced new WMI command: WMI_PEER_PARAM_FIXED_RATE. After peer
assoc, the peer fixed rate cmd will work for that specific peer.
Remaining peers will use auto rate. If both vdev fixed rate and peer
fixed rates are given, peer fixed rate will take effect to peers for
which this cmd is given. Remaining peers in that vdev, will use vdev
fixed rate.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently instant rx_duration always fetching as zero
in fw_stats debugfs entry if extended peer stats event
supports.
This patch updates instant rx_duration in fw_stats entry
based on extended peer stats and maintaining backward
compatibility for 10.2/10.x.
Tested HW: QCA9984.
Tested FW: 10.4-3.6.0.1-00004.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset HTT stats helps to get the aggregated HTT stats via
tracing and also we can clear the accumulated HTT stats with
this debugfs file.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the struct for PN replay protection and fragment packet
handler.
Also fix the bitmask of HTT_RX_DESC_HL_INFO_MCAST_BCAST to match what's currently
used by SDIO firmware. The defines are not used yet so it's safe to modify
them. Remove the conflicting HTT_RX_DESC_HL_INFO_FRAGMENT as
it's not either used in ath10k.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE
polling") introduced a regression where we try to sleep (grab a mutex)
in an atomic context:
[ 233.602619] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
[ 233.602626] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[ 233.602636] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.1.0-rc2 #4
[ 233.602642] Hardware name: Google Scarlet (DT)
[ 233.602647] Call trace:
[ 233.602663] dump_backtrace+0x0/0x11c
[ 233.602672] show_stack+0x20/0x28
[ 233.602681] dump_stack+0x98/0xbc
[ 233.602690] ___might_sleep+0x154/0x16c
[ 233.602696] __might_sleep+0x78/0x88
[ 233.602704] mutex_lock+0x2c/0x5c
[ 233.602717] ath10k_pci_diag_read_mem+0x68/0x21c [ath10k_pci]
[ 233.602725] ath10k_pci_diag_read32+0x48/0x74 [ath10k_pci]
[ 233.602733] ath10k_pci_dump_registers+0x5c/0x16c [ath10k_pci]
[ 233.602741] ath10k_pci_fw_crashed_dump+0xb8/0x548 [ath10k_pci]
[ 233.602749] ath10k_pci_napi_poll+0x60/0x128 [ath10k_pci]
[ 233.602757] net_rx_action+0x140/0x388
[ 233.602766] __do_softirq+0x1b0/0x35c
[...]
ath10k_pci_fw_crashed_dump() is called from NAPI contexts, and firmware
memory dumps are retrieved using the diag memory interface.
A simple reproduction case is to run this on QCA6174A /
WLAN.RM.4.4.1-00132-QCARMSWP-1, which happens to be a way to b0rk the
firmware:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value bs=4K count=1
of=/dev/null
(NB: simulated firmware crashes, via debugfs, don't trigger firmware
dumps.)
The fix is to move the crash-dump into a workqueue context, and avoid
relying on 'data_lock' for most mutual exclusion. We only keep using it
here for protecting 'fw_crash_counter', while the rest of the coredump
buffers are protected by a new 'dump_mutex'.
I've tested the above with simulated firmware crashes (debugfs 'reset'
file), real firmware crashes (the 'dd' command above), and a variety of
reboot and suspend/resume configurations on QCA6174A.
Reported here:
http://lkml.kernel.org/linux-wireless/20190325202706.GA68720@google.com
Fixes: 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE polling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Transmit completion for SDIO is similar to PCIe, modify the high
latency path to allow SDIO modules to use the msdu id.
kvalo: the original patch from Alagu enabled this only for SDIO but I'm not
sure should we also enable this with USB. I'll use bus params to enable this
for so that it's easy to enable also for USB later.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast/broadcast traffic destined for a particular vlan group will
always be encrypted in software. To enable dynamic VLANs, it requires
driver support for sending software encrypted packets.
In ath10k, sending software encrypted frames is allowed only when we insmod
the driver with cryptmode param set to 1, this configuration disables
hardware crypto and enables RAW mode implicitly. Since, enabling raw
mode has performance impact, this cannot be considered as an ideal
solution for supporting VLANs in the driver.
As an alternative take, in this approach, cryptographic keys for
unicast traffic (per peer PTKs) and keys for non-vlan group traffic
will be configured in hardware, allowing hardware encryption for unicast
and non-vlan group traffic. Only vlan group traffic will be encrypted in
software and pushed to the target with encap mode set to RAW in the TX
descriptors.
Not all firmwares can support this type of key configuration(having few
keys installed in hardware and few only in software); for this purpose a
new WMI service flag "WMI_SERVICE_PER_PACKET_SW_ENCRYPT" is introduced to
advertise this support.
Also, adding the logic required to send sw encrypted frames in raw mode.
Hardwares Tested : QCA9984, QCA988X
Firmwares Tested : 10.4-3.5.3-00057, 10.2.4-1.0-00042
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure fine timing measurement (FTM) responder role from the
ftm_responder bss param sent by mac80211. With FTM functionality offloaded
to firmware, adding the interface allows userspace to enable or disable
FTM responder functionality. ath10k disables it at the time of interface
creation.
Supported FW: 10.4
Tested on IPQ4019 with firmware: 10.4-3.2.1.1-00022
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The airtime of a transmitted frame will be estimated from last used tx rate
which the firmware reports with the peer stats feature
(WMI_SERVICE_PEER_STATS). The airtime is computed on the tx path and it
will be reported to mac80211 upon tx completion.
This change is based on Kan's orginal commit in Chromium tree
("CHROMIUM: ath10k: Implementing airtime fairness based TX scheduler")
ref: https://chromium-review.googlesource.com/588190
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Signed-off-by: Kan Yan <kyan@google.com>
[rmanohar@codeaurora.org: ported only the airtime computation]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[toke@redhat.com: Rebase to mac80211-next, add test note]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k maintains common txqs list for all stations. This txq
management can be removed by migrating to mac80211 txq APIs
and let mac80211 handle txqs reordering based on reported airtime.
By doing this, txq fairness maintained in ath10k i.e processing
N frames per txq is removed. By adapting to mac80211 APIs,
ath10k will support mac80211 based airtime fairness algorithm.
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Tested-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Mesh path metric needs tx rate information from ieee80211_tx_status()
call but in ath10k there is no mechanism to report tx rate information
via ieee80211_tx_status(), the tx rate is only accessible via
sta_statiscs() op.
Per peer tx stats has tx rate info available, Tx rate is available
to ath10k driver after every 4 PPDU sent in the air. For each PPDU,
ath10k driver updates rate informattion to mac80211 using
ieee80211_tx_rate_update().
Per peer txrate information is updated through per peer statistics
and is available for QCA9888/QCA9984/QCA4019/QCA998X only
Tested on QCA9984 with firmware-5.bin_10.4-3.5.3-00053
Tested on QCA998X with firmware-5.bin_10.2.4-1.0-00036
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The host driver currently expects the channel info event to be
received in pairs for all the channels, i.e. the first
chan_info event for a particular channel will not have the
COMPLETE flag set and the second chan_info event for the
same channel will have the COMPLETE flag set.
The HL2.0 firmware sends only one channel info event per channel
which is scanned without the COMPLETE flag set. After sending the
chan_info_event for all the channels, the HL2.0 firmware sends a
chan_info_event with COMPLETE flag set to indicate the completion
of the channel info event.
The firmware does not indicate this behavior with any service bitmap
and hence a new firmware feature flag is used to handle the modified
parsing of the channel info events, in the host driver, for the
firmware which sends single channel info event per scanned channel.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Co-developed-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds the tx statistics pkts/bytes dump
in rate table format.
Dump format table is similar to http://mcsindex.com/
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
command:
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan0/
stations/<MACADDR>/tx_stats
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Whenever the WCN3990 firmware becomes unavailable,
the host driver receives a FW down indication, post
which all the direct hardware register access should
be avoided, in order to prevent improper behavior in
the host driver.
Set the crash_flush flag when the host driver receives
a FW_DOWN_IND via qmi, in order to stop the untimely
hardware register access. Also handle the case, where
we need to do core register only for the first FW_READY
indication, which is when we initialize the host driver.
All the subsequent FW_READY indication will be received
in subsystem recovery case and we only need to do the
restart work. The state of driver is maintained using
flags to distinguish between first and subsequent FW_READY
indication received.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add WCN3990 QMI client handshakes for Q6 integrated WLAN connectivity
subsystem. This layer is responsible for communicating qmi control
messages to wifi fw QMI service using QMI messaging protocol.
Qualcomm MSM Interface(QMI) is a messaging format used to communicate
between components running between remote processors with underlying
transport layer based on integrated chipset(shared memory) or
discrete chipset(PCI/USB/SDIO/UART).
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add support to create the boardname for non-bmi targets
like WCN3990, which uses qmi for bdf download. This
boardname is used to parse the board data from board-2.bin.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Acked-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For WoWLAN support it is expected to support wake up based on discovery of
one or more known SSIDs. This is the WIPHY_WOWLAN_NET_DETECT feature,
which shows up as an NL80211 feature flag.
This shows up in 'iw phy' as:
WoWLAN support:
* wake up on network detection, up to 16 match sets
And it can be enabled with command:
iw phy0 wowlan enable net-detect interval 5000 delay 30 freqs 2412 matches ssid foo
Firmware will do scan by the configured parameters after suspend and
wakeup if it found matched SSIDs. Tested with QCA6174 hw3.0 with
firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
[kvalo@codeaurora.org: fix lots of endian bugs, whitespace, commit log and style cleanup]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch helps to get the power save state change of each peer
connected to the AP. With WMI_10_4_PEER_STA_PS_STATECHG_EVENTID
event, ps state of each peer is reported to user space via
debugfs.
Use the below command to get the ps state of each sta:
cat /sys/kernel/debug/ieee80211/phyX/netdev::wlanX/stations/
XX:XX:XX:XX:XX:XX/peer_ps_state
If STA is in power save state, we get the peer_ps_state value as 1.
if STA is not in power save state, we get the peer_ps_state value as 0.
If ps_state event is disabled, we get the peer_ps_state value as 2.
We can enable/disable the ps_state events using the debugfs flag
"ps_state_enable"
echo Y > /sys/kernel/debug/ieee80211/phyX/ath10k/ps_state_enable
Y = 1 to enable and Y = 0 to disable
Tested in QCA4019 with firmware ver 10.4-3.2.1.1-00011
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The vdev-start-response message should cause the
completion to fire, even in the error case. Otherwise,
the user still gets no useful information and everything
is blocked until the timeout period.
Add some warning text to print out the invalid status
code to aid debugging, and propagate failure code.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The bus type is used together with the other hw parameters
to find a matching entry in ath10k_hw_params_list for the device.
This is necessary since HL devices can have the same dev_id and
target_version as a corresponding LL device (same chipset) and
yet use a totally different configuration.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add dev_type parameter to struct ath10k_bus_params.
The dev type specifies if the device is a high latency device (usb and
sdio) or low latency device (pci, ahb and snoc)
The setup of high latency chips is sometimes different than
for chips using low latency interfaces.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This struct is used as argument to ath10k_core_register in order to
make it easier to add more bus parameters in the future.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds per station tx statistics support.
Per station tx stats include
- pkts/bytes transmitted at all possible rates(mcs/nss/bw/gi).
- ACK fails count
- ampdu bytes/pkts transmitted at all possible rates(mcs/nss/bw/gi).
- BA fails count
Tested on QCA9984/QCA4019/QCA988x
Firmware: 10.4-3.5.3-00057
10.2.4-1.0-00037
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch adds debugfs entry to enable/disable extended
tx statistics. Extended tx statistics are from peer stats
feature.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
To support dual-band variant of QCA9984, new extended board data (eBDF)
is introduced since existing board data ran out of space.
Below is the brief implementation & design detail,
----------------------------------------------------
1. New OTP changes to inform eBDF support in existing OTP download to
fetch board ID and chip ID. This is backward compatible and older
card sends 0 by default for eBDF support bit (bit 18 of OTP response) we
check in ath10k driver.
2. If eBDF is supported, then we need to fetch eBDF ID which is bundled
in downloaded board data. So again OTP is executed for knowing the eBDF ID.
This is done once we set 'board_data_initialized' bit. If eBDF ID
returned is zero, we continue booting with previous board data downloaded.
3. Based on the eBDF ID fetched, ath10k driver tries to download the
extended board data to a new offset ahead of already downloaded board
data address.
4. A new BD IE type, ATH10K_BD_IE_BOARD_EXT is added to differentiate in
bundling eBDF separately in board-2.bin and also to parse through
board bundle for eBDF download in ath10k boot.
5. If eBDF is not present in the board-2.bin bundle or when board ID is
zero, we do a fallback boot to "eboard.bin" in the same QCA9984/hw1.0 dir.
This is same as done to existing "board.bin" if board ID is not present
in board-2.bin bundle.
Current design is that eBDF size will be 2KB and eBDF ID will be
byte value.
Tested the above changes with dual-band variant of QCA9984 card. OTP
update needed for the test will be part of next FW release 10.4-3.6-xxxx.
Below are the logs with ath10k BOOT debugs enabled.
First OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for board id
boot get otp board id result 0x00040400 board_id 1 chip_id 0 ext_bid_support 1
..
Second OTP response :
---------------------
..
boot upload otp to 0x1234 len 9478 for ext board id
boot get otp ext board id result 0x00000005 ext_board_id 5
boot using eboard name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
..
Extended board data download:
------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 65 62 6f 61 72 64 -id=0,bmi-eboard
00000020: 2d 69 64 3d 35 -id=5
boot found match for name 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
boot found eboard data for 'bus=pci,bmi-chip-id=0,bmi-eboard-id=5'
using board api 2
boot writing ext board data to addr 0xc3000
..
Fallback Extended board data download from "eboard.bin":
---------------------------------------------------------
..
board name
00000000: 62 75 73 3d 70 63 69 2c 62 6d 69 2d 63 68 69 70 bus=pci,bmi-chip
00000010: 2d 69 64 3d 30 2c 62 6d 69 2d 62 6f 61 72 64 2d -id=0,bmi-board-
00000020: 69 64 3d 31 30 id=10
failed to fetch board data for bus=pci,bmi-chip-id=0,bmi-eboard-id=5 from ath10k/QCA9984/hw1.0/board-2.bin
boot fw request 'ath10k/QCA9984/hw1.0/eboard.bin': 0
using board api 1
boot writing ext board data to addr 0xc3000
..
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 transmits management frames via WMI
with reference. Currently, with the management
tx completion not being handled, these frames are
not getting freed even after the transmission status
is returned by the firmware.
The transmitted management frames should be freed
when the firmware sends the over-the-air tx status of
the corresponding management frames.
Handle the wmi mgmt tx completion event and free
the corresponding management frame.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The India regulatory domain allows CH 173, so add that to the
available channel list. I verified basic connectivity between
a 9880 and 9984 NIC.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In the 10.4-3.6 firmware branch there's a new DFS Host confirmation
feature which is advertised using WMI_SERVICE_HOST_DFS_CHECK_SUPPORT flag.
This new features enables the ath10k host to send information to the
firmware on the specifications of detected radar type. This allows the
firmware to validate if the host's radar pattern detector unit is
operational and check if the radar information shared by host matches
the radar pulses sent as phy error events from firmware. If the check
fails the firmware won't allow use of DFS channels on AP mode when using
FCC regulatory region.
Hence this patch is mandatory when using a firmware from 10.4-3.6 branch.
Else, DFS channels on FCC regions cannot be used.
Supported Chipsets : QCA9984/QCA9888/QCA4019
Firmware Version : 10.4-3.6-00104
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure channel dwell time from duration of the scan request
received from mac80211 when the duration is non-zero. When the
scan request does not have duration value, use the default ones,
the current implementation.
Corresponding flag NL80211_EXT_FEATURE_SET_SCAN_DWELL is
advertized.
Supported Chipsets:
-QCA988X/QCA9887 PCI
-QCA99X0/QCA9984/QCA9888/QCA4019 PCI
-QCA6174/QCA9377 PCI/USB/SDIO
-WCN3990 SNOC
Tested on QCA9984 with firmware ver 10.4-3.6-0010
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch add support to get RSSI from acknowledgment
frames for transmitted management frames.
hardware_used: QCA4019, QCA9984.
firmware version: 10.4-3.5.3-00052.
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently vdev stats displayed in fw_stats are applicable
only for TLV based firmware and fix it for 10.4 firmware
as of now. The vdev stats in 10.4 firmware is split into two
parts (vdev_stats, vdev_stats_extended). The actual stats
are captured only in extended vdev stats. In order to enable
vdev stats, appropriate feature bit will be set on extended
resource config. As FTM related counters are available only on
newer 10.4 based firmware, these counters will be displayed
only on valid data.
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Export the final Transmit Power Control (TPC) value, which is the
minimum of control power and existing TPC value to user space via
a new debugfs file "tpc_stats_final" to help with debugging.
It works with the new wmi cmd and event introduced in 10.4 firmware
branch.
WMI command ID: WMI_PDEV_GET_TPC_TABLE_CMDID
WMI event ID: WMI_PDEV_TPC_TABLE_EVENTID
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
$ cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats_final
TPC config for channel 5180 mode 10
CTL = 0x 0 Reg. Domain = 58
Antenna Gain = 0 Reg. Max Antenna Gain = 0
Power Limit = 60 Reg. Max Power = 60
Num tx chains = 2 Num supported rates = 109
******************* CDD POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
******************* STBC POWER TABLE ****************
No. Preamble Rate_code tpc_value1 tpc_value2 tpc_value3
0 CCK 0x40 0 0
1 CCK 0x41 0 0
[...]
107 HTCUP 0x 0 46 46
108 HTCUP 0x 0 46 46
***********************************
TXBF not supported
**********************************
The existing tpc_stats debugfs file provides the dump
which is minimum of target power and regulatory domain.
cat /sys/kernel/debug/ieee80211/phyX/ath10k/tpc_stats
Hardware_used: QCA4019
Firmware version: firmware-5.bin_10.4-3.0-00209
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Added per tid sta counters for the following
- Total number MSDUs received from firmware
- Number of MSDUs received with errors like decryption, crc, mic ,etc.
- Number of MSDUs dropped in the driver
- A-MPDU/A-MSDU subframe stats
- Number of MSDUS passed to mac80211
All stats other than A-MPDU stats are only for received data frames.
A-MPDU stats might have stats for management frames when monitor
interface is active where management frames are notified both in wmi
and HTT interfaces.
These per tid stats can be enabled with tid bitmask through a debugfs
like below
echo <tid_bitmask> > /sys/kernel/debug/ieee80211/phyX/ath10k/sta_tid_stats_mask
tid 16 (tid_bitmask 0x10000) is used for non-qos data/management frames
The stats are read from
/sys/kernel/debug/ieee80211/phyX/netdev\:wlanX/stations/<sta_mac>/dump_tid_stats
Sample output:
To enable rx stats for tid 0, 5 and 6,
echo 0x00000061 > /sys/kernel/debug/ieee80211/phy0/ath10k/sta_tid_stats_mask
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wlan15/stations/8c\:fd\:f0\:0a\:8e\:df/dump_tid_stats
Driver Rx pkt stats per tid, ([tid] count)
------------------------------------------
MSDUs from FW [00] 2567 [05] 3178 [06] 1089
MSDUs unchained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:chained [00] 0 [05] 0 [06] 0
MSDUs locally dropped:filtered [00] 0 [05] 0 [06] 0
MSDUs queued for mac80211 [00] 2567 [05] 3178 [06] 1089
MSDUs with error:fcs_err [00] 0 [05] 0 [06] 2
MSDUs with error:tkip_err [00] 0 [05] 0 [06] 0
MSDUs with error:crypt_err [00] 0 [05] 0 [06] 0
MSDUs with error:peer_idx_inval [00] 0 [05] 0 [06] 0
A-MPDU num subframes upto 10 [00] 2567 [05] 3178 [06] 1087
A-MPDU num subframes 11-20 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 21-30 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 31-40 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 41-50 [00] 0 [05] 0 [06] 0
A-MPDU num subframes 51-60 [00] 0 [05] 0 [06] 0
A-MPDU num subframes >60 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 1 [00] 2567 [05] 3178 [06] 1089
A-MSDU num subframes 2 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 3 [00] 0 [05] 0 [06] 0
A-MSDU num subframes 4 [00] 0 [05] 0 [06] 0
A-MSDU num subframes >4 [00] 0 [05] 0 [06] 0
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
