The IGTK keys are only removed by mac80211 after it has already
removed the AP station. This causes the driver to throw an error
because mac80211 is trying to remove the IGTK when the station doesn't
exist anymore.
The firmware is aware that the station has been removed and can deal
with it the next time we try to add an IGTK for a station, so we
shouldn't try to remove the key if the station ID is
IWL_MVM_INVALID_STA. Do this by removing the check for mvm_sta before
calling iwl_mvm_send_sta_igtk() and check return from that function
gracefully if the station ID is invalid.
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The only slightly tricky merge conflict was the netdevsim because the
mutex locking fix overlapped a lot of driver reload reorganization.
The rest were (relatively) trivial in nature.
Signed-off-by: David S. Miller <davem@davemloft.net>
iwl_mvm_tvqm_enable_txq() can return an error, notably if unable
to allocate memory for the queue. Handle this error throughout,
avoiding storing the invalid value into a u16 which later leads
to a disable of an invalid queue ("queue 65524 not used", where
65524 is just -ENOMEM in a u16).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There really is no need to make drivers call the
ieee80211_start_tx_ba_cb_irqsafe() function and then
schedule the worker if all we want is to set a bit.
Add a new return value (that was previously considered
invalid) to indicate that the driver is immediately
ready for the session, and make drivers use it. The
only drivers that remain different are the Intel ones
as they need to negotiate more with the firmware.
Link: https://lore.kernel.org/r/1570007543-I152912660131cbab2e5d80b4218238c20f8a06e5@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We're now left with a status bit that is never set and a few
other leftovers.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This variable read, but never set. Remove it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
These static functions are only used after their definition,
so we don't need the forward declarations.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The solution with the worker still had a bug, as in order
to get sta, rcu_read_lock should be used and thus no mutex
can be used inside iwl_mvm_rs_rate_init.
Also, spin_lock is a simpler solution, no need to spawn a
dedicated worker.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The only place where the command was sent as SYNC is during
init and this is not really critical. This change is required
for replacing RS mutex with a spinlock (in the subsequent patch),
since SYNC comamnd requres sleeping and thus the flow cannot
be done when holding a spinlock.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We will need a new type of synchronization message going
through all the RSS queues. Prepare the ground for this.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Rate perform uses the lq_sta table to calculate the next rate to scale
while rate init resets the same table,
Rate perform is done in soft irq context in parallel to rate init
that can be called in case we are doing changes like AP changes BW
or moving state for auth to assoc.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When building with -Wsometimes-uninitialized, Clang warns:
drivers/net/wireless/intel/iwlwifi/mvm/sta.c:2114:12: warning: variable
'queue' is used uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
Clang can't evaluate at this point that WARN(1, ...) always returns true
because __ret_warn_on is defined as !!(condition), which isn't
immediately evaluated as 1. Change this branch to else so that it's
clear to Clang that we intend to bail out here.
Link: https://github.com/ClangBuiltLinux/linux/issues/399
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
[added a few more braces]
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
AX210 devices support 256 BA (256 MPDUs in an AMPDU).
The firmware requires that the number of TFDs will be
minimum twice as big as the BA size (2 * 256 = 512).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcuHgsAAoJEG4XJFUm622bfo8H/3uRRxsQBHGg6e3NpELaxpNV
IfrPDtvxyfILzIepBBhnZYUY0OrlTHKfMmzFBD9FFMojsxBYddnLZ/0iKUNKfwLm
KzToW/64YJ784dc+tw85gjh8I3MB+RRoD0l01M1HuOkzQ4hDNEGK3IsMHsBs/oTZ
huiqTYsTxStOj53vOpQiBFZ1pYBtvGLMxBdSepDcR27bgT1gwriynCSkSNglDH8z
/t3m6hDGtZa6uVkoIVH+BAMu6+vt+vIkU/TOdmiW/zqBL2JYq6cDE0uIb3bLAzN6
uvS1Rj42P3OwHUwFavlUBdr5Rdcj6P24S5ZhtVaGGWCBjMZI5/nO7IjzwyQnQuQ=
=/6q9
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-04-18' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.2
Nothing really special standing out this time, iwlwifi being the most
active driver.
Major changes:
iwlwifi
* send NO_DATA events so they can be captured in radiotap
* support for multiple BSSID
* support for some new FW API versions
* support new hardware
* debugfs cleanups by Greg-KH
qtnfmac
* allow each MAC to specify its own regulatory rules
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Back in commit 4d339989ac ("iwlwifi: mvm: support ibss in dqa mode")
we changed queue selection for IBSS to be:
if (ieee80211_is_probe_resp(fc) || ieee80211_is_auth(fc) ||
ieee80211_is_deauth(fc))
return IWL_MVM_DQA_AP_PROBE_RESP_QUEUE;
if (info->hw_queue == info->control.vif->cab_queue)
return info->hw_queue;
return IWL_MVM_DQA_AP_PROBE_RESP_QUEUE;
Clearly, the thought at the time must've been that mac80211 will
select the hw_queue as the cab_queue, so that we'll return and use
that, where we store the multicast queue for IBSS. This, however,
isn't true because mac80211 doesn't implement powersave for IBSS
and thus selects the normal IBSS interface AC queue (best effort).
This therefore always used the probe response queue, which maps to
the BE FIFO.
In commit cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
we rethought this code, and as a consequence now started mapping the
multicast traffic to the multicast hardware queue since we no longer
relied on mac80211 selecting the queue, doing it ourselves instead.
This queue is mapped to the MCAST FIFO. however, this isn't actually
enabled/controlled by the firmware in IBSS mode because we don't
implement powersave, and frames from this queue can never go out in
this case.
Therefore, we got queue hang reports such as
https://bugzilla.kernel.org/show_bug.cgi?id=201707
Fix this by mapping the multicast queue to the BE FIFO in IBSS so
that all the frames can go out.
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
iwl_mvm_tx_mpdu() may run from iwl_mvm_add_new_dqa_stream_wk(), where
soft-IRQs aren't disabled. In this case, it may hold the station lock
and be interrupted by a soft-IRQ that also wants to acquire said lock,
leading to a deadlock.
Fix it by disabling soft-IRQs in iwl_mvm_add_new_dqa_stream_wk().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the old days, we could transmit with HW crypto with an arbitrary
key by filling it into TX_CMD. This was broken first with the advent
of CCMP/GCMP-256 keys which don't fit there.
This was broken *again* with the newer TX_CMD format on 22560+,
where we simply cannot pass key material anymore. However, we forgot
to update all the cases when we get a key from mac80211 and don't
program it into the hardware but still return 0 for HW crypto on TX.
In AP mode with WEP, we tried to fix this by programming the keys
separately for each station later, but this ultimately turns out to
be buggy, for example now it leaks memory when we have more than one
WEP key.
Fix this by simply using only SW crypto for WEP in newer devices by
returning -EOPNOTSUPP instead of trying to program WEP keys later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add new device family AX210.
Make the needed changes for this family.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In iwl_mvm_sta_alloc_queue_tvqm(), we know that we have a
station, so no need to check it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Recently we started to send the WEP keys to the firmware so
that we could use hardware Tx encryption also on newer
devices that require the keys to be installed in the firmware
for encryption (as opposed to older devices that can get
the key in the Tx command for each Tx).
When we implemented that, we forgot to remove the key when
we remove a station leading to a situation where a station
that connects and disconnects a lot of times exhausts the
key database inside the firmware.
A fix was made for that, but we always removed the same
key: mvmvif->ap_wep_key which means that we removed the
same key entry in the firmware. This can make sense since
in WEP, the key is the same for all the stations, but the
internal implementation of iwl_mvm_set_sta_key and
iwl_mvm_remove_sta_key assumes that each station uses a
different key in the firmware's key database.
So now we got to the situation where we have a single
ieee80211_key_conf instance that means, a single
ieee80211_key_conf.hw_key_idx index for several stations
and hence for several keys.
ieee80211_key_conf.hw_key_idx is set to 0 when the first
station associates, and then it is overwritten to 1 when
the second station associates which is a buggy of course.
This led to the following message upon the removal of the
second station:
iwlwifi 0000:00:03.0: offset 1 not used in fw key table.
WARNING: CPU: 2 PID: 27883 at net/mac80211/sta_info.c:1122 __sta_info_destroy_part2+0x16b/0x180 [mac80211]
RIP: 0010:__sta_info_destroy_part2+0x16b/0x180 [mac80211]
Call Trace:
__sta_info_destroy+0x2a/0x40 [mac80211]
sta_info_destroy_addr_bss+0x38/0x60 [mac80211]
ieee80211_del_station+0x1d/0x30 [mac80211]
nl80211_del_station+0xe0/0x1f0 [cfg80211]
Fix this by copying the ieee80211_key_conf structure for
each and every station. This is the easiest way to properly
remove the keys with the right index. Another solution
would have been to allow several stations to use the same
key offset in the firmware. That would require to change
the way we track keys in iwlmvm and not really worth it.
Also, maintain correctly fw_key_table when we add a key
for the multicast station.
Remove the key when we remove the multicast station.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Fixes: 337bfc9881 ("iwlwifi: mvm: set wep key for all stations in soft ap mode")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Simplify some return conditions found by running a semantic patch
to detect unnecessary assignments to local variables.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TX path lock was introduced in order to prevent out of order
invocations of TX.
This can happen in the following flow:
TX path invoked from net dev
Packet dequeued
TX path invoked from RX path
Packet dequeued
Packet TXed
Packet TXed
However, we don't really need a lock. If TX path is already
invoked from some location, other paths can simply abort their
execution, instead of waiting to the first path to finish, and
then discover queue is (likely) empty or stopped.
Replace the lock with an atomic variable to track TX ownership.
This simplifies the locking dependencies between RX and TX paths,
and should improve performance.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The value in txq_id can be out of array scope,
validate it before accessing the array.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move to use the new mac80211 TXQs implementation. This has
quite a few benefits for us. We can get rid of the awkward
mapping of DQA to mac80211 queues. We can stop buffering
traffic while waiting for the queue to be allocated. We can
also use mac80211 AMSDUs instead of building it ourselves.
The usage is pretty simple:
Each ieee80211_txq contains iwl_mvm_txq. There is such a
queue for each TID, and one for management frames. We keep
having static AP queues for probes and non-bufferable MMPDUs,
along with broadcast and multicast queues. Those are being
used from the "old" TX invocation path - iwl_mvm_mac_tx.
When there is a new frame in a TXQ, iwl_mvm_mac_wake_tx is
being called, and either invokes the TX path, or allocates
the queue if it does not exist.
Most of the TX path is left untouched, although we can consider
cleaning it up some more, for example get rid of the duplication
of txq_id in both iwl_mvm_txq and iwl_mvm_dqa_txq_info.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Sometimes, due to SCD bug, we need to start the queue with an
higher SSN. The queue allocation function currently increments
the SSN in the packet itself, but it is pointless, since this
value is overridden later by iwl_mvm_tx_mpdu with the value
from mvmsta->tid_data[tid].seq_number. Updating tid data is
sufficient.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If tx fails during connection establishment, try another antenna for
the next tx. This will increase the chance to establish connection if
one of the antennas is blocked. Note that the antenna is toggled even
when failing to tx data frames since connection establishment may use
EAPOLs for 802.1X authentication/ 4 way handshake.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the queue management code runs under mvm->mutex, so there are
only very few cases of accessing the data structures without it:
* TX path, which doesn't take any locks anyway
* iwl_mvm_wake_sw_queue() and iwl_mvm_stop_sw_queue() where we
just (atomically) read a bitmap, so the lock isn't needed.
Therefore, we can remove the spinlock. This enables some cleanup
in the ugly locking in iwl_mvm_inactivity_check().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we mark a TID as no longer having a queue, there's no
guarantee the TX path isn't using this txq_id right now,
having accessed it just before we reset the value. To fix
this, add synchronize_net() when we change the TIDs from
having a queue to not having one, so that we can then be
sure that the TX path is no longer accessing that queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We don't really need this state: instead of having an inactive
state where we can awaken zombie queues again if needed, just
keep them in their normal state unless a new queue is actually
needed and there's no other way of getting one.
We do this here by making the inactivity check not free queues
unless instructed that we now really need to allocate one to a
specific station, and in that case it'll just free the queue
immediately, without doing any inactivity step inbetween.
The only downside is a little bit more processing in this case,
but the code complexity is lower.
Additionally, this fixes a corner case: due to the way the code
worked, we could only ever reuse an inactive queue if it was
the reserved queue for a station, as iwl_mvm_find_free_queue()
would never consider returning an inactive queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We want to call iwl_mvm_inactivity_check() from here in the
next patch, so need to move the code down to be able to.
Fix a minor checkpatch complaint while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This function is only used in the file where it's declared,
so just make it static.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Instead of iterating all the queues after having potentially
changed some queue configurations, rechecking if that was done,
mark the ones that do need a TID change explicitly in a bitmap
and use that to send the change to the firmware.
While at it, also rename iwl_mvm_change_queue_owner() to
iwl_mvm_change_queue_tid() since that's more obvious - the
"kind" of owner isn't immediately clear right now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We set the queue to this state, only to pretty much immediately
move it out of it again. However, we can't even hit any of the
code that checks if the queue is reconfiguring, because all of
this happens under mvm->mutex and we hold the all the way from
marking the queue as RECONFIGURING to marking it as READY again.
Additionally, the queue that became RECONFIGURING would've been
in SHARED state before, and it can safely stay in that state. In
case of errors, it previously would have stayed in RECONFIGURING
which it could never have left again.
Remove the state entirely and just track the queues that need to
be reconfigured in a separate, local, bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We currently reconfigure the queues after the inactivity check,
but only in one of the two callers. This might leave queues in
a state where the TID owner is wrong, if called when reserving
a queue for a new station.
Clean this up and do the reconfiguration inside the inactivity
check function. This requires changing the locking, but one of
the two places already holds the mvm mutex and the other easily
can.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If TVQM is used we skip over this, move the code into a new
function to get rid of the label.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to build a bitmap first and then iterate,
just do the iteration with the right locking directly.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to have a hw refcount if we just mark the
command queue with a (fake) TID; at that point, the refcount
becomes equivalent to the hweight() of the TID bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
None of these functions really need to be separate, they're all
only used in sta.c, move them there and make them static.
Fix a small typo in related code while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support for setting keys for TKIP cipher suite was mistakenly removed
for AP mode. Fix this.
Fixes: 85aeb58cec ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When operating as a soft ap with wep security, the key was not
configured to the fw for the stations, based on the fact that the
key will be specified in the tx command.
However, in the new tx api the tx command does not include the key,
which resulted in all data frames going out un-encrypted.
Fix it by configuring the key for all the stations as they are added.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently, a BA session is opened when the tx traffic exceeds
10 frames per second. As a result of inter-op problems with some
APs, add a condition to open BA session only when station is
already authorized.
Fixes: 482e48440a ("iwlwifi: mvm: change open and close criteria of a BA session")
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When trying to open aggregations on 22000 HW before
traffic had actually passed, the driver will discover
it is missing a queue to aggregate on. In such a case -
allocate a queue.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
22000 devices rely on this flag to install the key to the right
queues. For earlier devices we didn't have a key / queue mapping and
the key was sent along with the Tx command for each Tx hence the
problem didn't arise.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When starting aggregation, the code checks the status of the queue
allocated to the aggregation tid, which might not yet be allocated
and thus the queue index may be invalid.
Fix this by reserving a new queue in case the queue id is invalid.
While at it, clean up some unreachable code (a condition that is
already handled earlier) and remove all the non-DQA comments since
non-DQA mode is no longer supported.
Fixes: cf961e1662 ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the driver failed to resume from D3, it is possible that it has
no valid aux station. In such case, fw restart will end up in sending
station related commands with an invalid station id, which will
result in an assert.
Fix this by allocating a new station id for the aux station if it
does not have a valid id even in the case of fw restart.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
