[why]
Original change 594b237b9a ("drm/amd/display: Add
interface to track PHY state") was implemented by assuming stream's
dpms off is equivalent to PHY power off.
This assumption doesn't hold in following situations:
1. MST multiple stream scenario, where multiple streams are sharing the
same PHY output. Toggle dpms off for one of the stream doesn't power
off the PHY due to the presence of other streams.
2. enable stream failure scenario, where enable stream fails due to
failure of link training. This will cause DPMS off is set to false, while
the actual PHY power state is off in certain cases.
Due to the problematic assumption, the logic will skip disabling
other streams for MST multiple stream scenario, therefore PHY is
not actually powered off.
[how]
1. Rework this refactor by moving PHY state update down to hardware
level, where we update PHY state in place when hardware sequencer
is actually changing the power state of the PHY hardware.
2. Reimplement symclk on TX off workaround in place when we are actually
calling transmitter control to power off PHY in dcn32. Note the workaround is
added due to the lack of proper software interface to set TX while keeping
symclk on. We plan to address this interface problem so we can set TX off
only without affecting symclk in future dcn versions.
Fixes: 594b237b9a ("drm/amd/display: Add interface to track PHY state")
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The interpretation of the number of memory channels
differ by memory type, and this affects channel width
for the DML input.
[How]
Set dram channel width according to memory type for
dcn314.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Sometimes pixel clock needs to remain active after transmitter disable.
[How]
Use update_phy_state to track PHY state after stream
enable/disable and program pixel clock as needed.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Brian Chang <Brian.Chang@amd.com>
Signed-off-by: Taimur Hassan <Syed.Hassan@amd.com>
Signed-off-by: Alvin Lee <alvin.lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Describe structs and enums used to set blend mode properties to MPC
blocks. Some pieces of information are already available as code
comments, and were just formatted. Others were collected and summarised
from discussions on AMD issue tracker[1][2].
[1] https://gitlab.freedesktop.org/drm/amd/-/issues/1734
[2] https://gitlab.freedesktop.org/drm/amd/-/issues/1769
v2:
- fix typos (Tales)
- add MPCC to MPC entry in the glossary
Signed-off-by: Melissa Wen <mwen@igalia.com>
Reviewed-by: Tales Aparecida <tales.aparecida@gmail.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We got a report from Stephen/Michael that the PowerPC build was failing
with the following error:
ld: drivers/gpu/drm/amd/display/dc/dml/display_mode_lib.o uses hard float, drivers/gpu/drm/amd/display/dc/dcn30/dcn30_optc.o uses soft float
ld: failed to merge target specific data of file drivers/gpu/drm/amd/display/dc/dcn30/dcn30_optc.o
This error happened because of the function optc3_set_vrr_m_const. This
function expects a double as a parameter in a code that is not allowed
to have FPU operations. After further investigation, it became clear
that optc3_set_vrr_m_const was never invoked, so we can safely drop this
function and fix the ld issue.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Melissa Wen <mwen@igalia.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Tested-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When Static screen from MALL, the cursor needs to be
cached if cursor exceeds 64x64 size.
[How]
Program the bit that cache cursor in MALL when size
of the cursor exceeds 64x64.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently programming incorrect hpo inst as well as selecting incorrect source
[HOW]
Use hpo inst instead of otg inst to select dpstreamclk inst
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We don't write out attributes after disabling and re-enabling the link
on some monitors, causing some, but not all, HDMI displays to fail to
lightup on DCN314.
[How]
Firmware used to do this after DIG link setup.
Since firmware is no longer doing this to support USB4 and dynamic link
remapping we'll need to add this to driver in the equivalent paths.
New optional callbacks were created in the stream encoder interface and
implementations were added for DCN314.
Reviewed-by: Michael Strauss <Michael.Strauss@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Setup the shift and mask of HDMI_ACP_SEND register
- Program the register in hdmi stream encoder
- Also update ACP register in azalia configuration
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alan Liu <HaoPing.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we tried to compile DCN32/321 for 32-bit architecture, we got this
error message:
ERROR: modpost: "__floatunsidf" [drivers/gpu/drm/amd/amdgpu/amdgpu.ko] undefined!
This was caused because we were trying to assign an unsigned int to a
double value which causes issues for 32-bit architecture. This issue can
be fixed by changing the value type.
Cc: Aurabindo Pillai <aurabindo.pillai@amd.com>
Cc: Harry Wentland <harry.wentland@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Randy Dunlap <rdunlap@infradead.org>
Fixes: 265280b998 ("drm/amd/display: add CLKMGR changes for DCN32/321")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add support to get VCO frequency from registers.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aurabindo Jayamohanan Pillai <Aurabindo.Pillai@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Video Timing Extended Metadata packet (VTEM) is required for features
like VRR and FVA
[How]
Adding support for VTEM transmission to stream encoders in DCN20 and DCN30
as part of FVA support
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Ahmad Othman <ahmad.othman@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and How]
dwbc_funcs.set/get_privacy_mask isn't being used anymore, drop it
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Alan Liu <HaoPing.Liu@amd.com>
Signed-off-by: Oliver Logush <oliver.logush@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PSR-SU Rate Control - or PSR-SU-RC - enables PSR-SU panels to work with
variable refresh rate to allow for more power savings. Lowering the
refresh rate can increase PSR residency by expanding the eDP main link
shut down duration. It can also lower panel power consumption.
There is a complication with PSR, since the eDP main link can be shut
down. Therefore, the timing controller (TCON) on the eDP sink nees to be
able to scan out its remote buffer independent of the main link. To
allow the eDP source to specify the sink's refresh rate while the link
is off, vendor-specific DPCD registers are used. This allows the eDP
source to then "Rate Control" the panel during PSR active.
[How]
Add DC support to communicate with PSR-SU-RC supported eDP sinks. The
sink will need to know the desired VTotal during PSR active.
This change only adds support to DC, support in amdgpu_dm is still
pending to enable this fully.
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Signed-off-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For Pixel Rate control, when on HDMI, HDMI DTO
should be selected instead of DP DTO.
[How]
Add HDMI member to dtbclk_dto_params, so it can be used tell apart HDMI
and DP DTO in the future.
Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Chris Park <chris.park@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
To involve the cursor position into dirty rectangle calculation.
[how]
- separate plane and cursor update by different DMUB command
- send the cursor information while cursor updating, when updating
cursor position/attribute, store cursor pos/attr to hubp, and
notify dmub FW to exit psr before program cursor registers
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To support PSR2 Source DPCD configuration
[How]
Update the PSR2 Source DPCD settings while the PSR2 enabled
Signed-off-by: David Zhang <dingchen.zhang@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Revised validation logic when marking for seamless boot. Init resources
accordingly when Pre-OS has ODM enabled. Reset ODM when transitioning
Pre-OS odm to Post-OS non-odm to avoid corruption. Apply logic to set
odm accordingly upon commit.
Signed-off-by: Duncan Ma <duncan.ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY & HOW]
Implements DTB ref clock switching with reg key default to OFF.
Refactors dccg DTBCLK logic to not store redundant state information
dccg. Also removes duplicated functions that should be inherited from
other dcn versions.
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
New dividers in DCCG need to be programmed depending
on encoder/stream type since pixels per clock in
OTG/DIO is different
DIO also needs additional programming depending on
pixels per clock
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Use DTBCLK for valid pixel clock generation
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Acked-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Description]
Add USBC connector ID to align with new VBIOS parsing.
Add seperate DCN321 link encoder due to different PHY version affecting
DP ALT related registers.
Signed-off-by: Dillon Varone <dillon.varone@amd.com>
Acked-by: Jerry Zuo <jerry.zuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
This patch adds necessary changes needed in DC files outside DCN32/321
specific tree
v2: squash in updates (Alex)
Signed-off-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
lut pipeline will be hooked up differently in some asics
need to add new interfaces
how:
add them
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin <martin.leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Very low rate to cause memory access issue while resetting
DMCUB after the halt command was sent to it.
The process of stopping fw of DMCUB may be timeout, that means
it is not in idle state, such as the window frames may still be
kept in cache, so reset by force will cause MMHUB hang.
[HOW]
After the halt command was sent, keep checking the DMCUB state until
it is idle.
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: hengzhou <Hengyong.Zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When enabling an HPO stream for the first time after having previously
enabled a DIO stream there may be lingering DIO FIFO errors even though
the DIO is no longer enabled.
These can cause display clock change to hang if we don't apply the
OTG disable workaround since the ramping logic is tied to OTG on.
[How]
The workaround wasn't being applied in the sequence of:
1 DIO stream
0 streams
1 HPO stream
because current_state has no stream or planes in its context - and
it's only swapped after optimize has finished.
We should be using the incoming context instead to determine whether
this logic is needed or not.
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why and how:
Revert this change. It was causing a black screen with certain blocks
Reviewed-by: George Shen <George.Shen@amd.com>
Acked-by: Jasdeep Dhillon <jdhillon@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Leung, Martin <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add new DSC interface to disconnect from pipe.
Reviewed-by: Alvin Lee <alvin.lee2@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clean up the sequence by making sure clk_mgr always builds a
reasonable clock table regardless of what we read from smu
by moving all defaults from resource soc struct to clk_mgr.
Now the only thing resource soc update does is read
the clock table and apply any DC specific policy decisions
to how clocks are populated in dml soc.
Reviewed-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Implement changes to transition from Pre-OS odm to
Post-OS odm support. Seamless boot case is also
considered.
[HOW]
Revised validation logic when marking for seamless
boot. Init resources accordingly when Pre-OS has
odm enabled. Reset odm and det size when transitioning
Pre-OS odm to Post-OS non-odm to avoid corruption.
Apply logic to set odm accordingly upon commit.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Signed-off-by: Duncan Ma <Duncan.Ma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When we enter FREESYNC_STATE_VIDEO, we want to use the extra vblank
portion to enter zstate if possible.
[how]
When we enter freesync, a full update is triggered and the new vtotal
with extra lines is passed to dml in a stream update. The time gained
from extra vblank lines is calculated in microseconds. We allow zstate
entry if the time gained is greater than 5 ms, which is the current
policy. Furthermore, an optimized value for min_dst_y_next_start is
calculated and written to its register. When exiting freesync, another
full update is triggered and default values are restored.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Gabe Teeger <gabe.teeger@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
DCN31 has this in zstate save/restore sequence.
need for non_zstate supported ASIC
[how]
add this PANEL_PWRSEQ_REF_DIV2 to existing panel_cntl_hw_init structure.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Underflow occurred while hubp ret pipe read is idle and the
second pipe is powered up and added. Flickering and underflow
are only observed on Pollock.
[How]
Check the hubp ret pipe read prior to unlock pipes.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Becle Lee <becle.lee@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To debug when p-state is being blocked and avoid PMFW hangs when
it does occur.
[How]
Re-use the DCN10 hardware sequencer by adding a new interface for
verifying p-state high on the hubbub. The interface is mostly the
same as the DCN10 interface, but the bit definitions have changed for
the debug bus.
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Factor set dp lane settings to link_hwss.
v2: fix statement with no effect warning (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change causes regression, that prevents some systems
from lighting up internal displays.
[How]
Revert this patch until a new solution is ready.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Zhan Liu <Zhan.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Current we have hundreds of if/else or switch statement to check
encoder type in dc_link level. The reason is because depending
on the type of encoder dc_link needs to perform similar programming
task but with different encoder interfaces. The story is to abstract
these interfaces so dc_link can just perform the programming task
without knowing the detail of which encoder it's dealing with.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
DCN guard is not necessary for DP2.x relevant logic.
Drop them.
v2: squash in fix for misplaced #endif (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Reviewed-by: Jerry Zuo <Jerry.Zuo@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
When there are more DP2.0 RXs connected than the number HPO DP link
encoders we have, we need to dynamically allocate HPO DP link encoder to
the port that needs it.
[how]
Only allocate HPO DP link encoder when it is needed.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
why:
Need interface to lower clocks when in dc (power save)
mode. Must be able to work with p_state unsupported cases
Can cause flicker when OS notifies us of dc state change
how:
added dal3 interface for KMD
added pathway to query smu for this softmax
added blank before clock change to override underflow
added logic to change clk based on pstatesupport and softmax
added logic in prepare/optimize_bw to conform while changing
clocks
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Pavle Kotarac <Pavle.Kotarac@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <Martin.Leung@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
After unloading driver, driver would not disable DSC function.
At next loading driver, driver would power all DSC engines off.
When driver powered the active DSC off, the screen would be gray
until reprograming DSC relatived register correcntly.
[HOW]
1. Remove DSC Power down code into init_pipes()
2. Depend on the OTG mapping information and DSC status to skip
power off for the working DSC.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Yi-Ling Chen <Yi-Ling.Chen2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
- Adding a DM interface to enable DSC over eDP on Linux
- DSC over eDP will allow to power savings by reducing
the bandwidth required to support panel's modes
- Apply link optimization algorithm to reduce link bandwidth
when DSC is enabled
[how]
- Read eDP panel's DSC capabilities
- Apply DSC policy on eDP panel based on its DSC capabilities
- Enable DSC encoder's on the pipe
- Enable DSC on panel's side by setting DSC_ENABLE DPCD register
- Adding link optimization algorithm to reduce link rate or lane
count based
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In fast boot sequence, when change dispclk, otg is disabled but digfe
is enabled. This may cause dig fifo error.
[How]
Reset dig fifo after enable otg.
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: JinZe.Xu <JinZe.Xu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
The MPC memory clocks should be powered down when not in use.
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Every other CM LUT power down sequence is deferred to next vupdate as
memory powerdown updates immediately while selecting LUTs is double
buffered. Previous update to defer LUT power down missed GAMCOR and
DSCL, causing some visible flicker when entering/exiting fullscreen
video playback.
[HOW]
Update dpp deferred update loop to check for valid DPPs in res_pool
instead of referencing dcn_ip which turns out to not be populated during
runtime. Move GAMCOR and DSCL powerdown to dpp deferred updates.
Reviewed-by: Haonan Wang <Haonan.Wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Disable root clock for dsc when not being used.
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
add display related cyan_skillfish files in.
makefile controlled by CONFIG_DRM_AMD_DC_DCN201 flag.
v2: squash in clang fixes from Harry, Nathan
v3: squash in missing CONFIG_DRM_AMD_DC check (Alex)
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Jun Lei <jun.lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Blnd, 3dlut, and shaper LUT select registers are double buffered, however
their accompanying LUT memory shutdown registers are not. As a result,
shutting down LUT memory immediately after setting a block to bypass causes
corruption as bypass only happens at next Vupdate.
[HOW]
Re-enable mem low power for CM block
Force optimization on next flip and disable LUT memory during optimization
sequence if LUT select field is then set to bypass
v2: squash in CONFIG_DRM_AMD_DC_DCN fix (Alex)
Reviewed-by: Eric Yang <Eric.Yang2@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
