The code from [1] sets SYS_CTRL_1 to different values depending on the
desired clock phase (0, 1/4, 1/2 or 3/4). A clock phase of 0 aligns the
positive edge of the clock with the pixel data while other values delay
the clock by a fraction of the clock period. A clock phase of 1/2 aligns
the negative edge of the clock with the pixel data.
The driver currently hard codes SYS_CTRL_1 to 0x88 which corresponds to
aligning the positive edge of the clock with the pixel data. This won't
work correctly for panels that require aligning the negative edge of the
clock with the pixel data.
Adjust the clock phase to 0 if DRM_BUS_FLAG_PIXDATA_DRIVE_POSEDGE is
present in bus_flags, otherwise adjust the clock phase to 1/2 as
appropriate for DRM_BUS_FLAG_PIXDATA_DRIVE_NEGEDGE.
[1] https://github.com/tdjastrzebski/ICN6211-Configurator
Signed-off-by: Jonathan Liu <net147@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220523130144.444225-1-net147@gmail.com
ADV7511_REG_CEC_RX_FRAME_HDR[] and ADV7511_REG_CEC_RX_FRAME_LEN[]
are only used inside adv7511_cec.c.
Move their definitions to this file to avoid the following build
warnings when CONFIG_DRM_I2C_ADV7511_CEC is not selected:
drivers/gpu/drm/bridge/adv7511/adv7511.h:229:17: warning: 'ADV7511_REG_CEC_RX_FRAME_HDR' defined but not used [-Wunused-const-variable=]
drivers/gpu/drm/bridge/adv7511/adv7511.h:235:17: warning: 'ADV7511_REG_CEC_RX_FRAME_LEN' defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Fixes: ab0af093bf ("drm: bridge: adv7511: use non-legacy mode for CEC RX")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220525215316.1133057-1-festevam@gmail.com
This reverts commit a77c2af099.
This patch depends on the patches just aplied to the media tree, and will
not build without them, which leaves drm-misc-next in a broken state.
Let's revert the two latter patches until rc1 has been branched,
and rc1 has been backmerged into drm-misc-next.
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20220523161520.354687-1-robert.foss@linaro.org
In commit 19cf41b64e ("lontium-lt9611: check a different
register bit for HDMI sensing"), the bit flag used to detect
HDMI cable connect was switched from BIT(2) to BIT(0) to improve
compatibility with some monitors that didn't seem to set BIT(2).
However, with that change, I've seen occasional issues where the
detection failed, because BIT(2) was set, but not BIT(0).
Unfortunately, as I understand it, the bits and their function
was never clearly documented. So lets instead check both
(BIT(2) | BIT(0)) when checking the register.
Cc: Yongqin Liu <yongqin.liu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: kernel-team@android.com
Fixes: 19cf41b64e ("lontium-lt9611: check a different register bit for HDMI sensing")
Signed-off-by: John Stultz <jstultz@google.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220511012612.3297577-2-jstultz@google.com
This patch simply consolidates the duplicated detection
functionality in the driver.
Cc: Yongqin Liu <yongqin.liu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Peter Collingbourne <pcc@google.com>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: kernel-team@android.com
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: John Stultz <jstultz@google.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220511012612.3297577-1-jstultz@google.com
Add of_node_put call on the endpoint node after it is not needed.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Javier Martinez Canillas <javierm@redhat.com>
Cc: Lyude Paul <lyude@redhat.com>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
Cc: Xin Ji <xji@analogixsemi.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220519112337.62198-1-marex@denx.de
Handle empty data-lanes = < >; property, which translates to
dsi_lanes = 0 as invalid.
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220518233844.248504-1-marex@denx.de
The Refclk may be supplied by SoC clock output instead of crystal
oscillator, make sure the clock are enabled before any other action
is performed with the bridge chip, otherwise it may either fail to
operate at all, or miss reset GPIO toggle.
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 7caff0fc42 ("drm/bridge: tc358767: Add DPI to eDP bridge driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220520121543.11550-1-marex@denx.de
The DSI-to-e(DP) mode is now supported, update the driver comment
to reflect this. No functional change.
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Fixes: 3080c21a04 ("drm/bridge: tc358767: Add DSI-to-(e)DP mode support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220519095137.11896-2-marex@denx.de
Handle empty data-lanes = < >; property, which translates to
dsi_lanes = 0 as invalid.
Fixes: ceb515ba29 ("drm/bridge: ti-sn65dsi83: Add TI SN65DSI83 and SN65DSI84 driver")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Andrzej Hajda <andrzej.hajda@intel.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220518233844.248504-1-marex@denx.de
As V4L2_FWNODE_BUS_TYPE_PARALLEL not properly descript for DPI
interface, this patch use new defined V4L2_FWNODE_BUS_TYPE_DPI for it.
Fixes: fd0310b6fe ("drm/bridge: anx7625: add MIPI DPI input feature")
Signed-off-by: Xin Ji <xji@analogixsemi.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220422084720.959271-4-xji@analogixsemi.com
The Freescale i.MX8MP LDB bridge is only present on Freescale i.MX8MP
SoCs. Hence add a dependency on ARCH_MXC, to prevent asking the user
about this driver when configuring a kernel without i.MX SoC support.
Fixes: 463db5c2ed ("drm: bridge: ldb: Implement simple Freescale i.MX8MP LDB bridge")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/449e08ca791a3ca308de5477c1bdc1f6eb1b34e7.1652104211.git.geert+renesas@glider.be
Drop two unused register macros, ICN6211_MAX_REGISTER and MIPI_ATE_STATUS_1,
neither of which is used and where the later should be specified using macro
MIPI_ATE_STATUS(1) instead. Drop the _(n) underscore and keep only the (n)
part of register macros. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220430025020.640277-1-marex@denx.de
Implement DSI-to-e(DP) mode, which is a mix of currently supported
DSI-to-DPI and DPI-to-(e)DP modes. The input side is configured as
either DSI or DPI, the DP AUX channel is registered for both input
side options, and the DSI host is attached for both DPI and (e)DP
output side options.
One notable detail is that the DSI-to-(e)DP mode requires the Pixel
PLL to be always enabled, which is not needed for DPI-to-(e)DP mode
which gets the matching clock direct from DPI Pixel Clock instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429205644.245480-2-marex@denx.de
Factor out register programming to configure the chip video RX side for
reception of video data from DSI or DPI. This is particularly useful in
the (e)DP output mode, where the video data can be received from either
DPI or DSI. While only the former is supported in (e)DP output mode so
far, this patch is added in preparation for addition of the later.
There is a change in the order or register programming in case of the
DSI-to-DPI mode. The DSI RX side is now programmed and enabled all in
one place after the output mode has been configured. Before this change,
the DSI RX has been programmed before the output mode has been set and
only enabled afterward. The order makes no difference however, since the
DSI RX is only enabled at the end either way.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429205644.245480-1-marex@denx.de
Add support for pre_enable and post_enable drm bridge control functions.
Making sure that host to be prepared before panel is powered up,
for the panels like TC358762.
Signed-off-by: Jayshri Pawar <jpawar@cadence.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220411140606.15654-1-jpawar@cadence.com
The Northwest Logic MIPI DSI host controller embedded in i.MX8qxp
works with a Mixel MIPI DPHY + LVDS PHY combo to support either
a MIPI DSI display or a LVDS display. So, this patch calls
phy_set_mode() from nwl_dsi_mode_set() to set PHY mode to MIPI DPHY
explicitly.
Cc: Guido Günther <agx@sigxcpu.org>
Cc: Robert Chiras <robert.chiras@nxp.com>
Cc: Martin Kepplinger <martin.kepplinger@puri.sm>
Cc: Andrzej Hajda <andrzej.hajda@intel.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: NXP Linux Team <linux-imx@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Acked-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419010852.452169-2-victor.liu@nxp.com
Per toshiba,tc358767.yaml DT binding document, port@2 the output (e)DP
port is optional. In case this port is not described in DT, the bridge
driver operates in DPI-to-DP mode. Make sure the driver treats this as
a valid mode of operation instead of reporting invalid mode.
Fixes: 71f7d9c031 ("drm/bridge: tc358767: Detect bridge mode from connected endpoints in DT")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220429204625.241591-1-marex@denx.de
The IT6505 is using functions provided by the DRM_DP_HELPER driver.
In order to avoid having the bridge enabled but the helper disabled,
let's add a select in order to be sure that the DP helper functions are
always available.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Signed-off-by: Fabien Parent <fparent@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426141536.274727-1-fparent@baylibre.com
tfp410_fini() always returns zero. Make it return no value which makes it
easier to see in the callers that there is no error to handle.
Also the return value of i2c and platform driver remove callbacks is
ignored anyway. This prepares making i2c and platform remove callbacks
return void, too.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428162803.185275-1-u.kleine-koenig@pengutronix.de
The i.MX8MP contains two syscon registers which are responsible
for configuring the on-SoC DPI-to-LVDS serializer. Implement a
simple bridge driver for this serializer.
--
- Add sentinel of_device_table
- Add RB from Sam
- Rename to fsl-ldb altogether
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Robby Cai <robby.cai@nxp.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
V2: - Rename syscon to fsl,syscon
V3: - Consistently use MX8MP
V4: - Fix MODULE_DESCRIPTION to also use MX8MP
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220426193645.244792-2-marex@denx.de
The ADV7511 family of bridges supports two modes for CEC RX: legacy and
non-legacy mode. The only difference is whether the chip uses a single
CEC RX buffer, or uses all three available RX buffers. Currently the
adv7511 driver uses legacy mode.
While debugging a stall in CEC RX on an ADV7535, we reached out to
Analog Devices, who suggested to use non-legacy mode instead. According
to the programming guide for the ADV7511 [1], and the register control
manual of the ADV7535 [2], this is the default behaviour on reset. As
previously stated, the adv7511 driver currently overrides this to legacy
mode.
This patch updates the adv7511 driver to instead use non-legacy mode
with all three CEC RX buffers. As a result of this change, we no longer
experience any stalling of CEC RX with the ADV7535. It is not known why
non-legacy mode solves this particular issue, but besides this, no
functional change is to be expected by this patch. Please note that this
has only been tested on an ADV7535.
What follows is a brief description of the non-legacy mode interrupt
handling behaviour. The programming guide in [1] gives a more detailed
explanation.
With three RX buffers, the interrupt handler checks the CEC_RX_STATUS
register (renamed from CEC_RX_ENABLE in this patch), which contains
2-bit psuedo-timestamps for each of the RX buffers. The RX timestamps
for each buffer represent the time of arrival for the CEC frame held in
a given buffer, with lower timestamp values indicating chronologically
older frames. A special value of 0 indicates that the given RX buffer
is inactive and should be skipped. The interrupt handler parses these
timestamps and then reads the active RX buffers in the prescribed order
using the same logic as before. Changes have been made to ensure that
the correct RX buffer is cleared after processing. This clearing
procesure also sets the timestamp of the given RX buffer to 0 to mark it
as inactive.
[1] https://www.analog.com/media/en/technical-documentation/user-guides/ADV7511_Programming_Guide.pdf
cf. CEC Map, register 0x4A, bit 3, default value 1:
0 = Use only buffer 0 to store CEC frames (Legacy mode)
1 = Use all 3 buffers to stores the CEC frames (Non-legacy mode)
[2] The ADV7535 register control manual is under NDA, but trust me when
I say that non-legacy CEC RX mode is the default here too. Here the
register is offset by 0x70 and has an address of 0xBA in the DSI_CEC
regiser map.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220423120854.1503163-3-alvin@pqrs.dk
Like the ADV7533, the ADV7535 has an offset for the CEC register map,
and it is the same value (ADV7533_REG_CEC_OFFSET = 0x70).
Rather than testing for numerous chip types in the offset calculations
throughout the driver, just compute it during driver probe and put it in
the private adv7511 data structure.
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220423120854.1503163-2-alvin@pqrs.dk
Send DPCD SET_POWER command to downstream in .atomic_disable to make the
downstream monitor enter the power down mode, so the device suspend won't
be affected.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Signed-off-by: Pin-Yen Lin <treapking@chromium.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220425134424.1150965-1-treapking@chromium.org
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Per toshiba,tc358767.yaml DT binding document, port@2 the output (e)DP
port is optional. In case this port is not described in DT, the bridge
driver operates in DPI-to-DP mode. The drm_of_find_panel_or_bridge()
call in tc_probe_edp_bridge_endpoint() returns -ENODEV in case port@2
is not present in DT and this specific return value is incorrectly
propagated outside of tc_probe_edp_bridge_endpoint() function. All
other error values must be propagated and are propagated correctly.
Return 0 in case the port@2 is missing instead, that reinstates the
original behavior before the commit this patch fixes.
Fixes: 8478095a8c ("drm/bridge: tc358767: Move (e)DP bridge endpoint parsing into dedicated function")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jonas Karlman <jonas@kwiboo.se>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220428213132.447890-1-marex@denx.de
SCDC is the Status and Control Data Channel for HDMI. Move the SCDC
helpers into display/ and split the header into files for core and
helpers. Update all affected drivers. No functional changes.
To avoid the proliferation of Kconfig options, SCDC is part of DRM's
support for HDMI. If necessary, a new option could make SCDC an
independent feature.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-9-tzimmermann@suse.de
Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.
The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.
Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.
v3:
* fix Kconfig dependencies (Javier)
v2:
* reduce HDMI helpers to avoid exporting functions (Jani)
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-8-tzimmermann@suse.de
Move DRM's HDCP helper library into the display/ subdirectory and add
it to DRM's display helpers. Split the header file into core and helpers.
Update all affected drivers. No functional changes.
v3:
* fix Kconfig dependencies
v2:
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-7-tzimmermann@suse.de
Replace the DP-helper module with a display-helper module. The
support for DisplayPort becomes an internal option that drivers
have to select. Update all related Kconfig and Makefile rules.
Besides the existing code for DisplayPort, the new module will
contain helpers for other video-output standards, such as HDMI.
Drivers will have to select their required video-output helpers.
Linking all display-related code into a single module avoids the
proliferation of small kernel modules.
The module parameters drm_dp_cec_unregister_delay, dp_aux_i2c_speed_khz,
and dp_aux_i2c_transfer_size are moving from the drm_dp_helper namespace
to drm_display_helper.
v2:
* mention module parameters in commit message (Javier)
* distiguish between display module and DP support in Kconfig
* update Makefile rules for DP helpers
* move Kconfig rules into separate file under display/
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-4-tzimmermann@suse.de
Rename dp/ to display/ to account for additional display-related
helpers, such as HDMI. Update all related include statements. No
functional changes.
Various drivers, such as i915 and amdgpu, use similar naming scheme
by putting code for video-output standards into a local display/
directory. The new directory's name is aligned with this convention.
v2:
* update commit message (Javier)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-3-tzimmermann@suse.de
it6505 depends on DRM_DP_AUX_BUS, the kconfig for it6505 should
reflect this dependency using 'select'.
Fixes: b5c84a9edc ("drm/bridge: add it6505 driver")
Reported-by: kernel test robot <lkp@intel.com>
Suggested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421131415.1289469-1-robert.foss@linaro.org
In the error handling path, the clk_prepare_enable() function
call should be balanced by a corresponding 'clk_disable_unprepare()'
call, as already done in the remove function.
Fixes: 3424e3a4f8 ("drm: bridge: analogix/dp: split exynos dp driver to bridge directory")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220420011644.25730-1-linmq006@gmail.com
The driver currently hard-codes DSI lane count to two, however the chip
is capable of operating in 1..4 DSI lanes mode. Parse 'data-lanes' DT
property and program the result into DSI_CTRL register.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220407185617.179573-2-marex@denx.de
As defined in the anx7625 dt-binding, the analogix,lane0-swing and
analogix,lane1-swing properties are uint8 arrays. Yet, the driver was
reading the array as if it were of uint32 and masking to 8-bit before
writing to the registers. This means that a devicetree written in
accordance to the dt-binding would have its values incorrectly parsed.
Fix the issue by reading the array as uint8 and storing them as uint8
internally, so that we can also drop the masking when writing the
registers.
Fixes: fd0310b6fe ("drm/bridge: anx7625: add MIPI DPI input feature")
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220408013034.673418-1-nfraprado@collabora.com
General Parallel Audio (GPA) interface is one of the supported
audio interface for synopsys HDMI module, which has verified for
i.MX8MPlus platform.
This is initial version for GPA.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/f21ba3e8c4d9d028ac74c6f3c588ddbffe739399.1649989179.git.Sandor.yu@nxp.com
PHY reset register(MC_PHYRSTZ) active high reset control for PHY GEN2,
and active low reset control for PHY GEN1.
Rename function dw_hdmi_phy_reset to dw_hdmi_phy_gen2_reset.
Add dw_hdmi_phy_gen1_reset function for PHY GEN1.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/e0b3be2d63fe3e95246fb8b8b0dcd57415b29e04.1649989179.git.Sandor.yu@nxp.com
HDMI1.4b specification section 6.5.3:
Source shall only send GCPs with non-zero CD to sinks
that indicate support for Deep Color.
DW HDMI GCP default enabled, but only transmit CD
and do not handle AVMUTE, PP norDefault_Phase (yet).
Disable Auto GCP when 24-bit color for sinks that not support Deep Color.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/78fa41e4fb3d3d53354034bc221fcf870dbac617.1649989179.git.Sandor.yu@nxp.com
i.MX8MPlus (v2.13a) has verified need the workaround to clear the
overflow with one iteration.
Only i.MX6Q(v1.30a) need the workaround with 4 iterations,
the others versions later than v1.3a have been identified as needing
the workaround with a single iteration.
Default enable the workaround with one iteration for all versions
later than v1.30a.
Signed-off-by: Sandor Yu <Sandor.yu@nxp.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/561951005a85574dcdd108e5d6a3a87df930ea3d.1649989179.git.Sandor.yu@nxp.com
If panel_bridge_attach() happens after DRM device registration, the
created connector will not be registered by the DRM core anymore. Fix
this by registering it explicitly in such case.
This fixes the following issue observed on Samsung Exynos4210-based Trats
board with a DSI panel (the panel driver is registered after the Exynos DRM
component device is bound):
$ ./modetest -c -Mexynos
could not get connector 56: No such file or directory
Segmentation fault
While touching this, move the connector reset() call also under the DRM
device registered check, because otherwise it is not really needed.
Fixes: 934aef885f ("drm: bridge: panel: Reset the connector state pointer")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419091422.4255-1-m.szyprowski@samsung.com
Connector detection using poll method won't work in case of bridge
attached to the encoder with the flag DRM_BRIDGE_ATTACH_NO_CONNECTOR, as
the code defaults to HPD.
Enable DRM_BRIDGE_OP_HPD based on HPD interrupt availability, so that
it will fall back to polling, if HPD is not available.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419142453.48839-1-biju.das.jz@bp.renesas.com
Add driver for Lontium LT9211 Single/Dual-Link DSI/LVDS or Single DPI to
Single-link/Dual-Link DSI/LVDS or Single DPI bridge. This chip is highly
capable at converting formats, but sadly it is also highly undocumented.
This driver is written without any documentation from Lontium and based
only on shreds of information available in various obscure example codes,
hence long runs of unknown register patches and lengthy delays in various
places. Whichever register meaning could be divined from its behavior has
at least a comment around it.
Currently the only mode tested is Single-link DSI to Single-link LVDS.
Dual-link LVDS might work as well, the register programming is in place,
but is untested.
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220419143958.94873-2-marex@denx.de
Speaker may share I2S with DP and .get_eld callback will be called when
speaker is playing. When HDMI wans't connected, the connector will be
null. Instead of return an error, fill in empty ELD.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Reviewed-by: Xin Ji <xji@analogixsemi.com>
Signed-off-by: Robert Foss <robert.foss@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220414090003.1806535-1-hsinyi@chromium.org
To make debugging easier, convert driver to regmap. Implement read and write
regmap tables for known registers, keep all known register readable and mark
those which are obviously read-only as not writeable.
Use common I2C regmap for the I2C configuration, implement custom regmap bus
for DSI configuration. The later is mandatory as this chip requires one extra
byte set to read access length between register address and data.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Mark Brown <broonie@kernel.org>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220403171004.368464-1-marex@denx.de
"hdmi-connector.yaml" bindings defines an optional property
"ddc-en-gpios" for a single gpio to enable DDC operation.
Usually this controls +5V power on the HDMI connector.
This +5V may also be needed for HPD.
This was not reflected in code but is needed to make the CI20
board work.
Now, the driver activates the ddc gpio after probe and
deactivates after remove so it is "almost on".
But only if this driver is loaded (and not e.g. blacklisted
as module).
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://patchwork.freedesktop.org/patch/msgid/3607e924b7c0cf0be956c0d49894be1442dbda41.1649330171.git.hns@goldelico.com
The module owner = THIS_MODULE is set by I2C core, drop duplicate assignment.
Fixes: 8dde6f7452 ("drm: bridge: icn6211: Add I2C configuration support")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Robert Foss <robert.foss@linaro.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Zimmermann <tzimmermann@suse.de>
To: dri-devel@lists.freedesktop.org
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220401113317.7033-1-marex@denx.de
