9178e3dcb121 ("mm: discard __GFP_ATOMIC") removed __GFP_ATOMIC,
replacing it with a check for not __GFP_DIRECT_RECLAIM.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220929161404.2769414-1-robdclark@gmail.com
msm-next for v6.1
DPU:
- simplified VBIF configuration
- cleaned up CTL interfaces to accept indices rather than flush masks
DSI:
- removed unused msm_display_dsc_config struct
- switch regulator calls to new bulk API
- switched to use PANEL_BRIDGE for directly attached panels
DSI PHY:
- converted drivers to use parent_hws instead of parent_names
DP:
- cleaned up pixel_rate handling
HDMI PHY:
- turned hdmi-phy-8996 into OF clk provider
core:
- misc dt-bindings fixes
- choose eDP as primary display if it's available
- support getting interconnects from either the mdss or the mdp5/dpu
device nodes
gpu+gem:
- Shrinker + LRU re-work:
- adds a shared GEM LRU+shrinker helper and moves msm over to that
- reduces lock contention between retire and submit by avoiding the
need to acquire obj lock in retire path (and instead using resv
seeing obj's busyness in the shrinker
- fix reclaim vs submit issues
- GEM fault injection for triggering userspace error paths
- Map/unmap optimization
- Improved robustness for a6xx GPU recovery
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGsrfrr9v1oR9S4oYfOs9jm=jbKQiwPBTrCRHrjYerJJFA@mail.gmail.com
On MSM8996 the HDMI PHY provides the PLL clock to the MMCC. As we are
preparing to convert the MSM8996 to use DT clocks properties (rather
than global clock names), register the OF clock provider.
While we are at it, also change the driver to use clk_parent_data rather
parent_names to setup a link to the XO clock.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/492318/
Link: https://lore.kernel.org/r/20220704161148.814510-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Clang warns:
drivers/gpu/drm/msm/dsi/dsi_host.c:1903:14: error: variable 'device_node' is uninitialized when used here [-Werror,-Wuninitialized]
of_node_put(device_node);
^~~~~~~~~~~
drivers/gpu/drm/msm/dsi/dsi_host.c:1870:44: note: initialize the variable 'device_node' to silence this warning
struct device_node *endpoint, *device_node;
^
= NULL
1 error generated.
device_node's assignment was removed but not all of its uses. Remove the
call to of_node_put() and the variable declaration to clean up the
warning.
Fixes: 36246dd50225 ("drm/msm/dsi: switch to DRM_PANEL_BRIDGE")
Link: https://github.com/ClangBuiltLinux/linux/issues/1700
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/500182/
Link: https://lore.kernel.org/r/20220829165450.217628-1-nathan@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Currently the DSI driver has two separate paths: one if the next device
in a chain is a bridge and another one if the panel is connected
directly to the DSI host. Simplify the code path by using panel-bridge
driver (already selected in Kconfig) and dropping support for
handling the panel directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/493608/
Link: https://lore.kernel.org/r/20220712132258.671263-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that struct mipi_dsi_device provides DSC data, fetch it from the
mentioned struct rather than from the struct drm_panel itself. This
would allow supporting MIPI DSI bridges handling DSC on their input
side.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/493307/
Link: https://lore.kernel.org/r/20220711094320.368062-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Return the value msm_dsi_phy_enable() directly instead of storing it in
another redundant variable.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/499621/
Link: https://lore.kernel.org/r/20220826072821.253150-1-ye.xingchen@zte.com.cn
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
It makes no sense to have the HPD worker in the MSM DSI driver anymore.
It is only queued from the dsi_host_attach/detach() callbacks, where
it plays no useful role. Either way the panel or next bridge will be
present and will report it's status directly.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/498740/
Link: https://lore.kernel.org/r/20220822174417.292926-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The dsi_phy_driver_probe() function has a "goto fail" for no
reason. Change it to just always return directly when it sees an
error. Make this simpler by leveraging dev_err_probe() which is
designed to make code like this shorter / simpler.
NOTE: as part of this, we now pass through error codes directly from
msm_ioremap_size() rather than translating to -ENOMEM. This changed
mostly because it's much more convenient when using dev_err_probe()
and also it's usually encouraged not to hide error codes like the old
code was doing unless there is a good reason. I can't see any reason
why we'd need to return -ENOMEM instead of -EINVAL from the probe
function.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496324/
Link: https://lore.kernel.org/r/20220804073608.v4.6.I969118a35934a0e5007fe4f80e3e28e9c0b7602a@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of the commit 1de452a0ed ("regulator: core: Allow drivers to
define their init data as const") we no longer need to do copying of
regulator bulk data from initdata to something dynamic. Let's take
advantage of that.
In addition to saving some code, this also moves us to using
ARRAY_SIZE() to specify how many regulators we have which is less
error prone.
This gets rid of some layers of wrappers which makes it obvious that
we can get rid of an extra error print.
devm_regulator_bulk_get_const() prints errors for you so you don't
need an extra layer of printing.
In all cases here I have preserved the old settings without any
investigation about whether the loads being set are sensible. In the
cases of some of the PHYs if several PHYs in the same file used
exactly the same settings I had them point to the same data structure.
NOTE: Though I haven't done the math, this is likely an overall
savings in terms of "static const" data. We previously always
allocated space for 8 supplies. Each of these supplies took up 36
bytes of data (32 for name, 4 for an int).
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496325/
Link: https://lore.kernel.org/r/20220804073608.v4.5.I55a9e65cb1c22221316629e98768ff473f47a067@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 6eabfc018e ("regulator: core: Allow specifying an
initial load w/ the bulk API") we can now specify the initial load in
the bulk data rather than having to manually call regulator_set_load()
on each regulator. Let's use it.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496319/
Link: https://lore.kernel.org/r/20220804073608.v4.4.I7b3c72949883846badb073cfeae985c55239da1d@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
As of commit 5451781dad ("regulator: core: Only count load for
enabled consumers"), a load isn't counted for a disabled
regulator. That means all the code in the DSI driver to specify and
set loads before disabling a regulator is not actually doing anything
useful. Let's remove it.
It should be noted that all of the loads set that were being specified
were pointless noise anyway. The only use for this number is to pick
between low power and high power modes of regulators. Regulators
appear to do this changeover at loads on the order of 10000 uA. You
would need a lot of clients of the same rail for that 100 uA number to
count for anything.
Note that now that we get rid of the setting of the load at disable
time, we can just set the load once when we first get the regulator
and then forget it.
It should also be noted that the regulator functions
regulator_bulk_enable() and regulator_set_load() already print error
messages when they encounter problems so while moving things around we
get rid of some extra error prints.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496320/
Link: https://lore.kernel.org/r/20220804073608.v4.3.If1f94fbbdb7c1d0fb3961de61483a851ad1971a7@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491927/
Link: https://lore.kernel.org/r/20220629225331.357308-12-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491923/
Link: https://lore.kernel.org/r/20220629225331.357308-11-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491921/
Link: https://lore.kernel.org/r/20220629225331.357308-10-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491925/
Link: https://lore.kernel.org/r/20220629225331.357308-9-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
parent_hw pointers are easier to manage and cheaper to use than
repeatedly formatting the parent name and subsequently leaving the clk
framework to perform lookups based on that name.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491929/
Link: https://lore.kernel.org/r/20220629225331.357308-8-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Now that the last DSI PHY PLL driver (dsi_phy_28nm_8960) has been
converted to use a simple stack-local char-array instead of a
devm_kzalloc heap allocation we can safely call sizeof() on every string
variable (that's now a sized array instead of a pointer) passed into
snprintf instead of hardcoding the size.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491920/
Link: https://lore.kernel.org/r/20220629225331.357308-7-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The clock names formatted into the hw_clk's init structure are only used
for the duration of the registration function where they are kstrdup'ed,
making it unnecessary to keep the allocations alive for the duration of
the device (through devm).
Just like the other DSI PHY PLL clock trees, use a stack-local char
array and save on memory outside of the pll_28nm_register function.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491917/
Link: https://lore.kernel.org/r/20220629225331.357308-6-marijn.suijten@somainline.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The commit 613cbd1da3 ("drm/msm/dsi: use devm_clk_*register to registe
DSI PHY clocks") introduced the devm_ prefix to clk_hw registration
calls, without updating the indentation of the arguments on the
following lines.
Similarly commit e55b3fbbbb ("drm/msm/dsi: drop PLL accessor
functions") moved from pll_write to dsi_phy_write without updating the
indentation of followup arguments either.
Preparing for a series that heavily touches the clk calls, reflow and
reindent function calls that are adhering to an 80-char column limit by
spanning multiple lines. Where function names are very long the
arguments are indented with a fixed number of two tab characters instead
of aligning with the opening parenthesis of the function call.
Signed-off-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/491931/
Link: https://lore.kernel.org/r/20220629225331.357308-5-marijn.suijten@somainline.org
[DB: adjusted commit message to make checkpatch happy]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
At current implementation there is an extra 0 at 1.62G link rate which
cause no correct pixel_div selected for 1.62G link rate to calculate
mvid and nvid. This patch delete the extra 0 to have mvid and nvid be
calculated correctly.
Changes in v2:
-- fix Fixes tag's text
Changes in v3:
-- fix misspelling of "Reviewed-by"
Fixes: 937f941ca0 ("drm/msm/dp: Use qmp phy for DP PLL and PHY")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/499328/
Link: https://lore.kernel.org/r/1661372150-3764-1-git-send-email-quic_khsieh@quicinc.com
[DB: rewrapped commit message]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Build robots complain
smatch warnings:
drivers/gpu/drm/msm/dp/dp_link.c:969 dp_link_process_link_status_update() warn: inconsistent indenting
Fix it along with a trailing space from the same commit.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Fixes: ea530388e6 ("drm/msm/dp: skip checking LINK_STATUS_UPDATED bit")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/498954/
Link: https://lore.kernel.org/r/20220823212302.1744145-1-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This API isn't really more than a couple lines now that we don't store
the pixel_rate to the struct member. Inline it into the caller.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/490775/
Link: https://lore.kernel.org/r/20220623002540.871994-4-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
This struct member is stored to in the function that calls the function
which uses it. That's possible with a function argument instead of
storing to a struct member. Pass the pixel_rate as an argument instead
to simplify the code. Note that dp_ctrl_link_maintenance() was storing
the pixel_rate but never using it so we just remove the assignment from
there.
Cc: Kuogee Hsieh <quic_khsieh@quicinc.com>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/490772/
Link: https://lore.kernel.org/r/20220623002540.871994-3-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Let's move these functions around to avoid having to forward declare
dp_ctrl_on_stream_phy_test_report(). Also remove
dp_ctrl_reinitialize_mainlink() forward declaration because we're doing
that sort of task.
Reviewed-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/490771/
Link: https://lore.kernel.org/r/20220623002540.871994-2-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Instead of querying the CTL for the flush mask (for SSPP, LM or DSPP),
storing the mask in the mixer configuration and then pushing the mask to
the CTL, tell CTL to cache the flush in place.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/473159/
Link: https://lore.kernel.org/r/20220209172520.3719906-9-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is no need to keep a separate function for calling into the ctl if
we already know all the details. Inline this function in the dpu_crtc.c
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/473152/
Link: https://lore.kernel.org/r/20220209172520.3719906-7-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Stop limiting zpos property values, we use normalized_zpos anyway. And
nothing stops userspace from assigning several planes to a single zpos
(it is a userspace bug, but the kernel is forgiving about it).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/473147/
Link: https://lore.kernel.org/r/20220209172520.3719906-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Master/virtual planes were used for multirect support. In preparation to
reworking DPU planes, drop support for master planes (which was not used
anyway).
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/473146/
Link: https://lore.kernel.org/r/20220209172520.3719906-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Follow up the merge of address fields and drop the variable that became
unused after the commit 9403f9a42c ("drm/msm/dpu: merge base_off with
blk_off in struct dpu_hw_blk_reg_map").
Fixes: 9403f9a42c ("drm/msm/dpu: merge base_off with blk_off in struct dpu_hw_blk_reg_map")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/498736/
Link: https://lore.kernel.org/r/20220822172204.281045-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drivers' .remove and .shutdown callbacks are executed on different code
paths. The former is called when a device is removed from the bus, while
the latter is called at system shutdown time to quiesce the device.
This means that some overlap exists between the two, because both have to
take care of properly shutting down the hardware. But currently the logic
used in these two callbacks isn't consistent in msm drivers, which could
lead to kernel panic.
For example, on .remove the component is deleted and its .unbind callback
leads to the hardware being shutdown but only if the DRM device has been
marked as registered.
That check doesn't exist in the .shutdown logic and this can lead to the
driver calling drm_atomic_helper_shutdown() for a DRM device that hasn't
been properly initialized.
A situation like this can happen if drivers for expected sub-devices fail
to probe, since the .bind callback will never be executed. If that is the
case, drm_atomic_helper_shutdown() will attempt to take mutexes that are
only initialized if drm_mode_config_init() is called during a device bind.
This bug was attempted to be fixed in commit 623f279c77 ("drm/msm: fix
shutdown hook in case GPU components failed to bind"), but unfortunately
it still happens in some cases as the one mentioned above, i.e:
systemd-shutdown[1]: Powering off.
kvm: exiting hardware virtualization
platform wifi-firmware.0: Removing from iommu group 12
platform video-firmware.0: Removing from iommu group 10
------------[ cut here ]------------
WARNING: CPU: 6 PID: 1 at drivers/gpu/drm/drm_modeset_lock.c:317 drm_modeset_lock_all_ctx+0x3c4/0x3d0
...
Hardware name: Google CoachZ (rev3+) (DT)
pstate: a0400009 (NzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : drm_modeset_lock_all_ctx+0x3c4/0x3d0
lr : drm_modeset_lock_all_ctx+0x48/0x3d0
sp : ffff80000805bb80
x29: ffff80000805bb80 x28: ffff327c00128000 x27: 0000000000000000
x26: 0000000000000000 x25: 0000000000000001 x24: ffffc95d820ec030
x23: ffff327c00bbd090 x22: ffffc95d8215eca0 x21: ffff327c039c5800
x20: ffff327c039c5988 x19: ffff80000805bbe8 x18: 0000000000000034
x17: 000000040044ffff x16: ffffc95d80cac920 x15: 0000000000000000
x14: 0000000000000315 x13: 0000000000000315 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : ffff80000805bc28 x7 : 0000000000000000 x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : ffff327c00128000 x1 : 0000000000000000 x0 : ffff327c039c59b0
Call trace:
drm_modeset_lock_all_ctx+0x3c4/0x3d0
drm_atomic_helper_shutdown+0x70/0x134
msm_drv_shutdown+0x30/0x40
platform_shutdown+0x28/0x40
device_shutdown+0x148/0x350
kernel_power_off+0x38/0x80
__do_sys_reboot+0x288/0x2c0
__arm64_sys_reboot+0x28/0x34
invoke_syscall+0x48/0x114
el0_svc_common.constprop.0+0x44/0xec
do_el0_svc+0x2c/0xc0
el0_svc+0x2c/0x84
el0t_64_sync_handler+0x11c/0x150
el0t_64_sync+0x18c/0x190
---[ end trace 0000000000000000 ]---
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000018
Mem abort info:
ESR = 0x0000000096000004
EC = 0x25: DABT (current EL), IL = 32 bits
SET = 0, FnV = 0
EA = 0, S1PTW = 0
FSC = 0x04: level 0 translation fault
Data abort info:
ISV = 0, ISS = 0x00000004
CM = 0, WnR = 0
user pgtable: 4k pages, 48-bit VAs, pgdp=000000010eab1000
[0000000000000018] pgd=0000000000000000, p4d=0000000000000000
Internal error: Oops: 96000004 [#1] PREEMPT SMP
...
Hardware name: Google CoachZ (rev3+) (DT)
pstate: a0400009 (NzCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : ww_mutex_lock+0x28/0x32c
lr : drm_modeset_lock_all_ctx+0x1b0/0x3d0
sp : ffff80000805bb50
x29: ffff80000805bb50 x28: ffff327c00128000 x27: 0000000000000000
x26: 0000000000000000 x25: 0000000000000001 x24: 0000000000000018
x23: ffff80000805bc10 x22: ffff327c039c5ad8 x21: ffff327c039c5800
x20: ffff80000805bbe8 x19: 0000000000000018 x18: 0000000000000034
x17: 000000040044ffff x16: ffffc95d80cac920 x15: 0000000000000000
x14: 0000000000000315 x13: 0000000000000315 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000000 x9 : 0000000000000000
x8 : ffff80000805bc28 x7 : 0000000000000000 x6 : 0000000000000000
x5 : 0000000000000000 x4 : 0000000000000000 x3 : 0000000000000000
x2 : ffff327c00128000 x1 : 0000000000000000 x0 : 0000000000000018
Call trace:
ww_mutex_lock+0x28/0x32c
drm_modeset_lock_all_ctx+0x1b0/0x3d0
drm_atomic_helper_shutdown+0x70/0x134
msm_drv_shutdown+0x30/0x40
platform_shutdown+0x28/0x40
device_shutdown+0x148/0x350
kernel_power_off+0x38/0x80
__do_sys_reboot+0x288/0x2c0
__arm64_sys_reboot+0x28/0x34
invoke_syscall+0x48/0x114
el0_svc_common.constprop.0+0x44/0xec
do_el0_svc+0x2c/0xc0
el0_svc+0x2c/0x84
el0t_64_sync_handler+0x11c/0x150
el0t_64_sync+0x18c/0x190
Code: aa0103f4 d503201f d2800001 aa0103e3 (c8e37c02)
---[ end trace 0000000000000000 ]---
Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b
Kernel Offset: 0x495d77c00000 from 0xffff800008000000
PHYS_OFFSET: 0xffffcd8500000000
CPU features: 0x800,00c2a015,19801c82
Memory Limit: none
---[ end Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b ]---
Fixes: 9d5cbf5fe4 ("drm/msm: add shutdown support for display platform_driver")
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/497842/
Link: https://lore.kernel.org/r/20220816134612.916527-1-javierm@redhat.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Drop the dpu_cfg variable and corresponding kzalloc, which became unused
after changing hw catalog to static configuration.
Fixes: de7d480f5e ("drm/msm/dpu: make dpu hardware catalog static const")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/498738/
Link: https://lore.kernel.org/r/20220822172455.282923-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Using IS_ERR_OR_NULL() together with PTR_ERR() is a typical mistake. If
the value is NULL, then the function will return 0 instead of a proper
return code. Moreover dpu_hw_vbif_init() function can not return NULL.
So, replace corresponding IS_ERR_OR_NULL() call with IS_ERR().
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/489570/
Link: https://lore.kernel.org/r/20220615125703.24647-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Remove loops over hw_vbif. Instead always VBIF's idx as an index in the
array. This fixes an error in dpu_kms_hw_init(), where we fill
dpu_kms->hw_vbif[i], but check for an error pointer at
dpu_kms->hw_vbif[vbif_idx].
Fixes: 25fdd5933e ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/489569/
Link: https://lore.kernel.org/r/20220615125703.24647-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
The commit 6874f48bb8 ("drm/msm: make mdp5/dpu devices master
components") changed the MDP5 driver to look for the interconnect paths
in the MDSS device rather than in the MDP5 device itself. This was left
unnoticed since on my testing devices the interconnects probably didn't
reach the sync state.
Rather than just using the MDP5 device for ICC path lookups for the MDP5
devices, introduce an additional helper to check both MDP5/DPU and MDSS
nodes. This will be helpful for the MDP5->DPU conversion, since the
driver will have to check both nodes.
Fixes: 6874f48bb8 ("drm/msm: make mdp5/dpu devices master components")
Reported-by: Marijn Suijten <marijn.suijten@somainline.org>
Reported-by: Yassine Oudjana <y.oudjana@protonmail.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Tested-by: Marijn Suijten <marijn.suijten@somainline.org> # On sdm630
Tested-by: Yassine Oudjana <y.oudjana@protonmail.com> # msm8996
Patchwork: https://patchwork.freedesktop.org/patch/496488/
Link: https://lore.kernel.org/r/20220805115630.506391-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is no need to use the struct msm_display_dsc_config wrapper inside
the dsi driver, use the struct drm_dsc_config directly to pass pps data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/493341/
Link: https://lore.kernel.org/r/20220711100432.455268-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
There is no need to use the struct msm_display_dsc_config wrapper inside
the dpu driver, use the struct drm_dsc_config directly to pass pps data.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Patchwork: https://patchwork.freedesktop.org/patch/493340/
Link: https://lore.kernel.org/r/20220711100432.455268-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
If the previous thing cat'ing $debugfs/rd left the FIFO full, then
subsequent open could deadlock in rd_write() (because open is blocked,
not giving a chance for read() to consume any data in the FIFO). Also
it is generally a good idea to clear out old data from the FIFO.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Patchwork: https://patchwork.freedesktop.org/patch/496706/
Link: https://lore.kernel.org/r/20220807160901.2353471-2-robdclark@gmail.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
In the event that devm_devfreq_add_device() fails the device's qos freq
list is left referencing df->idle_freq and df->boost_freq. Attempting to
initialize devfreq again after a probe deferral will then cause invalid
memory accesses in dev_pm_qos_add_request().
Fix this by dropping the requests in the error path.
Fixes: 7c0ffcd40b ("drm/msm/gpu: Respect PM QoS constraints")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/493001/
Link: https://lore.kernel.org/r/20220708162632.3529864-1-bjorn.andersson@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
1 regulator is listed but the number 2 is specified. This presumably
means we try to get a regulator with no name. Fix it.
Fixes: 462f7017a6 ("drm/msm/dsi: Fix DSI and DSI PHY regulator config from SDM660")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Marijn Suijten <marijn.suijten@somainline.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/496323/
Link: https://lore.kernel.org/r/20220804073608.v4.2.I94b3c3e412b7c208061349f05659e126483171b1@changeid
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Data Symbols scrambled is required for tps4 at link training 2.
Therefore SCRAMBLING_DISABLE bit should not be set for tps4 to
work.
RECOVERED_CLOCK_OUT_EN is for enable simple EYE test for jitter
measurement with minimal equipment for embedded applications purpose
and is not required to be set during normal operation. Current
implementation always have RECOVERED_CLOCK_OUT_EN bit set which
cause SCRAMBLING_DISABLE bit wrongly set at tps4 which prevent
tps4 from working.
This patch delete setting RECOVERED_CLOCK_OUT_EN to fix
SCRAMBLING_DISABLE be wrongly set at tps4.
Changes in v2:
-- fix Fixes tag
Changes in v3:
-- revise commit text
Changes in v4:
-- fix commit text newline
Changes in v5:
-- fix commit text line over 75 chars
Fixes: c943b4948b ("drm/msm/dp: add displayPort driver support")
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/497194/
Link: https://lore.kernel.org/r/1660258670-4200-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
dpu_encoder_helper_phys_cleanup() was not populating neither
wb or intf to the intf_cfg before calling the reset_intf_cfg().
This causes the reset of the active bits of wb/intf to be
skipped which is incorrect.
Fix this by populating the relevant wb or intf indices correctly.
Fixes: ae4d721ce1 ("drm/msm/dpu: add an API to reset the encoder related hw blocks")
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Jessica Zhang <quic_jesszhan@quicinc.com>
Tested-by: Jessica Zhang <quic_jesszhan@quicinc.com> # Trogdor (SC8170)
Patchwork: https://patchwork.freedesktop.org/patch/494298/
Link: https://lore.kernel.org/r/1657912468-17254-1-git-send-email-quic_abhinavk@quicinc.com
Signed-off-by: Rob Clark <robdclark@chromium.org>
Some userspace presumes that the first connected connector is the main
display, where it's supposed to display e.g. the login screen. For
laptops, this should be the main panel.
This patch call drm_helper_move_panel_connectors_to_head() after
drm_bridge_connector_init() to make sure eDP stay at head of
connected connector list. This fixes unexpected corruption happen
at eDP panel if eDP is not placed at head of connected connector
list.
Changes in v2:
-- move drm_helper_move_panel_connectors_to_head() to
dpu_kms_drm_obj_init()
Changes in v4:
-- move drm_helper_move_panel_connectors_to_head() to msm_drm_init()
Signed-off-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Fixes: ef7837ff09 ("drm/msm/dp: Add DP controllers for sc7280")
Patchwork: https://patchwork.freedesktop.org/patch/492581/
Link: https://lore.kernel.org/r/1657135928-31195-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
drm-misc-next for v6.1-rc1:
[airlied - fix sun4i_tv build]
UAPI Changes:
- Hide unregistered connectors from GETCONNECTOR ioctl.
- drm/virtio no longer advertises LINEAR modifier, as it doesn't work.
-
Cross-subsystem Changes:
- Fix GPF in udmabuf failure path.
Core Changes:
- Rework TTM placement to use intersect/compatible functions.
- Drop legacy DP-MST support.
- More DP-MST related fixes, and move all state into atomic.
- Make DRM_MIPI_DBI select DRM_KMS_HELPER.
- Add audio_infoframe packing for DP.
- Add logging when some atomic check functions fail.
- Assorted documentation updates and fixes.
Driver Changes:
- Assorted cleanups and fixes in msm, lcdif, nouveau, virtio,
panel/ilitek, bridge/icn6211, tve200, gma500, bridge/*, panfrost, via,
bochs, qxl, sun4i.
- Add add AUO B133UAN02.1, IVO M133NW4J-R3, Innolux N120ACA-EA1 eDP panels.
- Improve DP-MST modeset state handling in amdgpu, nouveau, i915.
- Drop DP-MST from radeon driver, it was broken and only user of legacy
DP-MST.
- Handle unplugging better in vc4.
- Simplify drm cmdparser tests.
- Add DP support to ti-sn65dsi86.
- Add MT8195 DP support to mediatek.
- Support RGB565, XRGB64, and ARGB64 formats in vkms.
- Convert sun4i tv support to atomic.
- Refactor vc4/vec TV Modesetting, and fix timings.
- Use atomic helpers instead of simple display helpers in ssd130x.
Maintainer changes:
- Add Douglas Anderson as reviewer for panel-edp.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a489485b-3ebc-c734-0f80-aed963d89efe@linux.intel.com
UAPI Changes:
Cross-subsystem Changes:
- DMA-buf: documentation updates.
- Assorted small fixes to vga16fb
- Fix fbdev drivers to use the aperture helpers.
- Make removal of conflicting drivers work correctly without fbdev enabled.
Core Changes:
- bridge, scheduler, dp-mst: Assorted small fixes.
- Add more format helpers to fourcc, and use it to replace the cpp usage.
- Add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx (single channel), and DRM_FORMAT_Dxx
("darkness", inverted single channel)
- Add packed AYUV8888 and XYUV8888 formats.
- Assorted documentation updates.
- Rename ttm_bo_init to ttm_bo_init_validate.
- Allow TTM bo's to exist without backing store.
- Convert drm selftests to kunit.
- Add managed init functions for (panel) bridge, crtc, encoder and connector.
- Fix endianness handling in various format conversion helpers.
- Make tests pass on big-endian platforms, and add test for rgb888 -> rgb565
- Move DRM_PLANE_HELPER_NO_SCALING to atomic helpers and rename, so
drm_plane_helper is no longer needed in most drivers.
- Use idr_init_base instead of idr_init.
- Rename FB and GEM CMA helpers to DMA helpers.
- Rework XRGB8888 related conversion helpers, and add drm_fb_blit() that
takes a iosys_map. Make drm_fb_memcpy take an iosys_map too.
- Move edid luminance calculation to core, and use it in i915.
Driver Changes:
- bridge/{adv7511,ti-sn65dsi86,parade-ps8640}, panel/{simple,nt35510,tc358767},
nouveau, sun4i, mipi-dsi, mgag200, bochs, arm, komeda, vmwgfx, pl111:
Assorted small fixes and doc updates.
- vc4: Rework hdmi power up, and depend on PM.
- panel/simple: Add Samsung LTL101AL01.
- ingenic: Add JZ4760(B) support, avoid a modeset when sharpness property
is unchanged, and use the new PM ops.
- Revert some amdgpu commits that cause garbaged graphics when starting
X, and reapply them with the real problem fixed.
- Completely rework vc4 init to use managed helpers.
- Rename via_drv to via_dri1, and move all stuff there only used by the
dri1 implementation in preperation for atomic modeset.
- Use regmap bulk write in ssd130x.
- Power sequence and clock updates to it6505.
- Split panel-sitrox-st7701 init sequence and rework mode programming code.
- virtio: Improve error and edge conditions handling, and convert to use managed
helpers.
- Add Samsung LTL101AL01, B120XAN01.0, R140NWF5 RH, DMT028VGHMCMI-1A T, panels.
- Add generic fbdev support to komeda.
- Split mgag200 modeset handling to make it more model-specific.
- Convert simpledrm to use atomic helpers.
- Improve udl suspend/disconnect handling.
-----BEGIN PGP SIGNATURE-----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=kU/l
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2022-08-20-1' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v6.1:
UAPI Changes:
Cross-subsystem Changes:
- DMA-buf: documentation updates.
- Assorted small fixes to vga16fb
- Fix fbdev drivers to use the aperture helpers.
- Make removal of conflicting drivers work correctly without fbdev enabled.
Core Changes:
- bridge, scheduler, dp-mst: Assorted small fixes.
- Add more format helpers to fourcc, and use it to replace the cpp usage.
- Add DRM_FORMAT_Cxx, DRM_FORMAT_Rxx (single channel), and DRM_FORMAT_Dxx
("darkness", inverted single channel)
- Add packed AYUV8888 and XYUV8888 formats.
- Assorted documentation updates.
- Rename ttm_bo_init to ttm_bo_init_validate.
- Allow TTM bo's to exist without backing store.
- Convert drm selftests to kunit.
- Add managed init functions for (panel) bridge, crtc, encoder and connector.
- Fix endianness handling in various format conversion helpers.
- Make tests pass on big-endian platforms, and add test for rgb888 -> rgb565
- Move DRM_PLANE_HELPER_NO_SCALING to atomic helpers and rename, so
drm_plane_helper is no longer needed in most drivers.
- Use idr_init_base instead of idr_init.
- Rename FB and GEM CMA helpers to DMA helpers.
- Rework XRGB8888 related conversion helpers, and add drm_fb_blit() that
takes a iosys_map. Make drm_fb_memcpy take an iosys_map too.
- Move edid luminance calculation to core, and use it in i915.
Driver Changes:
- bridge/{adv7511,ti-sn65dsi86,parade-ps8640}, panel/{simple,nt35510,tc358767},
nouveau, sun4i, mipi-dsi, mgag200, bochs, arm, komeda, vmwgfx, pl111:
Assorted small fixes and doc updates.
- vc4: Rework hdmi power up, and depend on PM.
- panel/simple: Add Samsung LTL101AL01.
- ingenic: Add JZ4760(B) support, avoid a modeset when sharpness property
is unchanged, and use the new PM ops.
- Revert some amdgpu commits that cause garbaged graphics when starting
X, and reapply them with the real problem fixed.
- Completely rework vc4 init to use managed helpers.
- Rename via_drv to via_dri1, and move all stuff there only used by the
dri1 implementation in preperation for atomic modeset.
- Use regmap bulk write in ssd130x.
- Power sequence and clock updates to it6505.
- Split panel-sitrox-st7701 init sequence and rework mode programming code.
- virtio: Improve error and edge conditions handling, and convert to use managed
helpers.
- Add Samsung LTL101AL01, B120XAN01.0, R140NWF5 RH, DMT028VGHMCMI-1A T, panels.
- Add generic fbdev support to komeda.
- Split mgag200 modeset handling to make it more model-specific.
- Convert simpledrm to use atomic helpers.
- Improve udl suspend/disconnect handling.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/f0c71766-61e8-19b7-763a-5fbcdefc633d@linux.intel.com
