VF was not able to send tagged traffic when it didn't
have any VLAN interfaces and VLAN anti-spoofing was enabled.
Fix this by allowing VFs with no VLAN filters to send tagged
traffic. After VF adds a VLAN interface it will be able to
send tagged traffic matching VLAN filters only.
Testing hints:
1. Spawn VF
2. Send tagged packet from a VF
3. The packet should be sent out and not dropped
4. Add a VLAN interface on VF
5. Send tagged packet on that VLAN interface
6. Packet should be sent out and not dropped
7. Send tagged packet with id different than VLAN interface
8. Packet should be dropped
Fixes: daf4dd1643 ("ice: Refactor spoofcheck configuration functions")
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 1273f89578 ("ice: Fix broken IFF_ALLMULTI handling")
introduced new checks when setting/clearing promiscuous mode. But if the
requested promiscuous mode setting already exists, an -EEXIST error
message would be printed. This is incorrect because promiscuous mode is
either on/off and shouldn't print an error when the requested
configuration is already set.
This can happen when removing a bridge with two bonded interfaces and
promiscuous most isn't fully cleared from VLAN VSI in hardware.
Fix this by ignoring cases where requested promiscuous mode exists.
Fixes: 1273f89578 ("ice: Fix broken IFF_ALLMULTI handling")
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Link: https://lore.kernel.org/all/CAK8fFZ7m-KR57M_rYX6xZN39K89O=LGooYkKsu6HKt0Bs+x6xQ@mail.gmail.com/
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When at least two interfaces are bonded and a bridge is enabled on the
bond, an error can occur when the bridge is removed and re-added. The
reason for the error is because promiscuous mode was not fully cleared from
the VLAN VSI in the hardware. With this change, promiscuous mode is
properly removed when the bridge disconnects from bonding.
[ 1033.676359] bond1: link status definitely down for interface enp95s0f0, disabling it
[ 1033.676366] bond1: making interface enp175s0f0 the new active one
[ 1033.676369] device enp95s0f0 left promiscuous mode
[ 1033.676522] device enp175s0f0 entered promiscuous mode
[ 1033.676901] ice 0000:af:00.0 enp175s0f0: Error setting Multicast promiscuous mode on VSI 6
[ 1041.795662] ice 0000:af:00.0 enp175s0f0: Error setting Multicast promiscuous mode on VSI 6
[ 1041.944826] bond1: link status definitely down for interface enp175s0f0, disabling it
[ 1041.944874] device enp175s0f0 left promiscuous mode
[ 1041.944918] bond1: now running without any active interface!
Fixes: c31af68a1b ("ice: Add outer_vlan_ops and VSI specific VLAN ops implementations")
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Link: https://lore.kernel.org/all/CAK8fFZ7m-KR57M_rYX6xZN39K89O=LGooYkKsu6HKt0Bs+x6xQ@mail.gmail.com/
Tested-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Tested-by: Igor Raits <igor@gooddata.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Ignore EEXIST error when setting promiscuous mode.
This fix is needed because the driver could set promiscuous mode
when it still has not cleared properly.
Promiscuous mode could be set only once, so setting it second
time will be rejected.
Fixes: 5eda8afd6b ("ice: Add support for PF/VF promiscuous mode")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Link: https://lore.kernel.org/all/CAK8fFZ7m-KR57M_rYX6xZN39K89O=LGooYkKsu6HKt0Bs+x6xQ@mail.gmail.com/
Tested-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Tested-by: Igor Raits <igor@gooddata.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Avoid enabling or disabling VLAN 0 when trying to set promiscuous
VLAN mode if double VLAN mode is enabled. This fix is needed
because the driver tries to add the VLAN 0 filter twice (once for
inner and once for outer) when double VLAN mode is enabled. The
filter program is rejected by the firmware when double VLAN is
enabled, because the promiscuous filter only needs to be set once.
This issue was missed in the initial implementation of double VLAN
mode.
Fixes: 5eda8afd6b ("ice: Add support for PF/VF promiscuous mode")
Signed-off-by: Grzegorz Siwik <grzegorz.siwik@intel.com>
Link: https://lore.kernel.org/all/CAK8fFZ7m-KR57M_rYX6xZN39K89O=LGooYkKsu6HKt0Bs+x6xQ@mail.gmail.com/
Tested-by: Jaroslav Pulchart <jaroslav.pulchart@gooddata.com>
Tested-by: Igor Raits <igor@gooddata.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
-queue
Tony Nguyen says:
====================
Intel Wired LAN Driver Updates 2022-08-11 (ice)
This series contains updates to ice driver only.
Benjamin corrects a misplaced parenthesis for a WARN_ON check.
Michal removes WARN_ON from a check as its recoverable and not
warranting of a call trace.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit b03d519d34 ("ice: store VF pointer instead of VF ID")
WARN_ON checks were added to validate the vsi->vf pointer and
catch programming errors. However, one check to vsi->vf was missed.
This caused a call trace when resetting VFs.
Fix ice_vsi_rebuild by encompassing VF pointer in WARN_ON check.
Fixes: b03d519d34 ("ice: store VF pointer instead of VF ID")
Signed-off-by: Benjamin Mikailenko <benjamin.mikailenko@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
This branch consists of:
Qu Wenruo:
lib: bitmap: fix the duplicated comments on bitmap_to_arr64()
https://lore.kernel.org/lkml/0d85e1dbad52ad7fb5787c4432bdb36cbd24f632.1656063005.git.wqu@suse.com/
Alexander Lobakin:
bitops: let optimize out non-atomic bitops on compile-time constants
https://lore.kernel.org/lkml/20220624121313.2382500-1-alexandr.lobakin@intel.com/T/
Yury Norov:
lib: cleanup bitmap-related headers
https://lore.kernel.org/linux-arm-kernel/YtCVeOGLiQ4gNPSf@yury-laptop/T/#m305522194c4d38edfdaffa71fcaaf2e2ca00a961
Alexander Lobakin:
x86/olpc: fix 'logical not is only applied to the left hand side'
https://www.spinics.net/lists/kernel/msg4440064.html
Yury Norov:
lib/nodemask: inline wrappers around bitmap
https://lore.kernel.org/all/20220723214537.2054208-1-yury.norov@gmail.com/
-----BEGIN PGP SIGNATURE-----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=4dTW
-----END PGP SIGNATURE-----
Merge tag 'bitmap-6.0-rc1' of https://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- fix the duplicated comments on bitmap_to_arr64() (Qu Wenruo)
- optimize out non-atomic bitops on compile-time constants (Alexander
Lobakin)
- cleanup bitmap-related headers (Yury Norov)
- x86/olpc: fix 'logical not is only applied to the left hand side'
(Alexander Lobakin)
- lib/nodemask: inline wrappers around bitmap (Yury Norov)
* tag 'bitmap-6.0-rc1' of https://github.com/norov/linux: (26 commits)
lib/nodemask: inline next_node_in() and node_random()
powerpc: drop dependency on <asm/machdep.h> in archrandom.h
x86/olpc: fix 'logical not is only applied to the left hand side'
lib/cpumask: move some one-line wrappers to header file
headers/deps: mm: align MANITAINERS and Docs with new gfp.h structure
headers/deps: mm: Split <linux/gfp_types.h> out of <linux/gfp.h>
headers/deps: mm: Optimize <linux/gfp.h> header dependencies
lib/cpumask: move trivial wrappers around find_bit to the header
lib/cpumask: change return types to unsigned where appropriate
cpumask: change return types to bool where appropriate
lib/bitmap: change type of bitmap_weight to unsigned long
lib/bitmap: change return types to bool where appropriate
arm: align find_bit declarations with generic kernel
iommu/vt-d: avoid invalid memory access via node_online(NUMA_NO_NODE)
lib/test_bitmap: test the tail after bitmap_to_arr64()
lib/bitmap: fix off-by-one in bitmap_to_arr64()
lib: test_bitmap: add compile-time optimization/evaluations assertions
bitmap: don't assume compiler evaluates small mem*() builtins calls
net/ice: fix initializing the bitmap in the switch code
bitops: let optimize out non-atomic bitops on compile-time constants
...
vsi->current_netdev_flags is used store the current net device
flags, not the active netdevice features. So it should use
vsi->netdev->featurs, rather than vsi->current_netdev_flags
to check NETIF_F_HW_VLAN_CTAG_FILTER.
Fixes: 1babaf77f4 ("ice: Advertise 802.1ad VLAN filtering and offloads for PF netdev")
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Acked-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
1GbE Intel Wired LAN Driver Updates 2022-07-28
Jacob Keller says:
Convert all of the Intel drivers with PTP support to the newer .adjfine
implementation which uses scaled parts per million.
This improves the precision of the frequency adjustments by taking advantage
of the full scaled parts per million input coming from user space.
In addition, all implementations are converted to using the
mul_u64_u64_div_u64 function which better handles the intermediate value.
This function supports architecture specific instructions where possible to
avoid loss of precision if the normal 64-bit multiplication would overflow.
Of note, the i40e implementation is now able to avoid loss of precision on
slower link speeds by taking advantage of this to multiply by the link speed
factor first. This results in a significantly more precise adjustment by
allowing the calculation to impact the lower bits.
This also gets us a step closer to being able to remove the .adjfreq
entirely by removing its use from many drivers.
I plan to follow this up with a series to update the drivers from other
vendors and drop the .adjfreq implementation entirely.
* '1GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
igb: convert .adjfreq to .adjfine
ixgbe: convert .adjfreq to .adjfine
i40e: convert .adjfreq to .adjfine
i40e: use mul_u64_u64_div_u64 for PTP frequency calculation
e1000e: convert .adjfreq to .adjfine
e1000e: remove unnecessary range check in e1000e_phc_adjfreq
ice: implement adjfine with mul_u64_u64_div_u64
====================
Link: https://lore.kernel.org/r/20220728181836.3387862-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-07-28
This series contains updates to ice driver only.
Michal allows for VF true promiscuous mode to be set for multiple VFs
and adds clearing of promiscuous filters when VF trust is removed.
Maciej refactors ice_set_features() to track/check changed features
instead of constantly checking against netdev features and adds support for
NETIF_F_LOOPBACK.
* '100GbE' of git://git.kernel.org/pub/scm/linux/kernel/git/tnguy/next-queue:
ice: allow toggling loopback mode via ndo_set_features callback
ice: compress branches in ice_set_features()
ice: Fix promiscuous mode not turning off
ice: Introduce enabling promiscuous mode on multiple VF's
====================
Link: https://lore.kernel.org/r/20220728195538.3391360-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for NETIF_F_LOOPBACK. This feature can be set via:
$ ethtool -K eth0 loopback <on|off>
Feature can be useful for local data path tests.
Acked-by: Jakub Kicinski <kuba@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Instead of rather verbose comparison of current netdev->features bits vs
the incoming ones from user, let us compress them by a helper features
set that will be the result of netdev->features XOR features. This way,
current, extensive branches:
if (features & NETIF_F_BIT && !(netdev->features & NETIF_F_BIT))
set_feature(true);
else if (!(features & NETIF_F_BIT) && netdev->features & NETIF_F_BIT)
set_feature(false);
can become:
netdev_features_t changed = netdev->features ^ features;
if (changed & NETIF_F_BIT)
set_feature(!!(features & NETIF_F_BIT));
This is nothing new as currently several other drivers use this
approach, which I find much more convenient.
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When trust is turned off for the VF, the expectation is that promiscuous
and allmulticast filters are removed. Currently default VSI filter is not
getting cleared in this flow.
Example:
ip link set enp236s0f0 vf 0 trust on
ip link set enp236s0f0v0 promisc on
ip link set enp236s0f0 vf 0 trust off
/* promiscuous mode is still enabled on VF0 */
Remove switch filters for both cases.
This commit fixes above behavior by removing default VSI filters and
allmulticast filters when vf-true-promisc-support is OFF.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In current implementation default VSI switch filter is only able to
forward traffic to a single VSI. This limits promiscuous mode with
private flag 'vf-true-promisc-support' to a single VF. Enabling it on
the second VF won't work. Also allmulticast support doesn't seem to be
properly implemented when vf-true-promisc-support is true.
Use standard ice_add_rule_internal() function that already implements
forwarding to multiple VSI's instead of constructing AQ call manually.
Add switch filter for allmulticast mode when vf-true-promisc-support is
enabled. The same filter is added regardless of the flag - it doesn't
matter for this case.
Remove unnecessary fields in switch structure. From now on book keeping
will be done by ice_add_rule_internal().
Refactor unnecessarily passed function arguments.
To test:
1) Create 2 VM's, and two VF's. Attach VF's to VM's.
2) Enable promiscuous mode on both of them and check if
traffic is seen on both of them.
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The PTP frequency adjustment code needs to determine an appropriate
adjustment given an input scaled_ppm adjustment.
We calculate the adjustment to the register by multiplying the base
(nominal) increment value by the scaled_ppm and then dividing by the
scaled one million value.
For very large adjustments, this might overflow. To avoid this, both the
scaled_ppm and divisor values are downshifted.
We can avoid that on X86 architectures by using mul_u64_u64_div_u64. This
helper function will perform the multiplication and division with 128bit
intermediate values. We know that scaled_ppm is never larger than the
divisor so this operation will never result in an overflow.
This improves the accuracy of the calculations for large adjustment values
on X86. It is likely an improvement on other architectures as well because
the default implementation of mul_u64_u64_div_u64 is smarter than the
original approach taken in the ice code.
Additionally, this implementation is easier to read, using fewer local
variables and lines of code to implement.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Currently loopback test is failiing due to the error returned from
ice_vsi_vlan_setup(). Skip calling it when preparing loopback VSI.
Fixes: 0e674aeb0b ("ice: Add handler for ethtool selftest")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tx side sets EOP and RS bits on descriptors to indicate that a
particular descriptor is the last one and needs to generate an irq when
it was sent. These bits should not be checked on completion path
regardless whether it's the Tx or the Rx. DD bit serves this purpose and
it indicates that a particular descriptor is either for Rx or was
successfully Txed. EOF is also set as loopback test does not xmit
fragmented frames.
Look at (DD | EOF) bits setting in ice_lbtest_receive_frames() instead
of EOP and RS pair.
Fixes: 0e674aeb0b ("ice: Add handler for ethtool selftest")
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: George Kuruvinakunnel <george.kuruvinakunnel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver currently does not allow two VSIs in the same PF domain
to have the same unicast MAC address. This is incorrect in the sense
that a policy decision is being made in the driver when it must be
left to the user. This approach was causing issues when rebooting
the system with VFs spawned not being able to change their MAC addresses.
Such errors were present in dmesg:
[ 7921.068237] ice 0000:b6:00.2 ens2f2: Unicast MAC 6a:0d:e4:70:ca:d1 already
exists on this PF. Preventing setting VF 7 unicast MAC address to 6a:0d:e4:70:ca:d1
Fix that by removing this restriction. Doing this also allows
us to remove some additional code that's checking if a unicast MAC
filter already exists.
Fixes: 47ebc7b024 ("ice: Check if unicast MAC exists before setting VF MAC")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Sylwester Dziedziuch <sylwesterx.dziedziuch@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Fix checksum offload on VXLAN tunnels.
In case, when mpls protocol is not used, set l4 header to transport
header of skb. This fixes case, when user tries to offload checksums
of VXLAN tunneled traffic.
Steps for reproduction (requires link partner with tunnels):
ip l s enp130s0f0 up
ip a f enp130s0f0
ip a a 10.10.110.2/24 dev enp130s0f0
ip l s enp130s0f0 mtu 1600
ip link add vxlan12_sut type vxlan id 12 group 238.168.100.100 dev enp130s0f0 dstport 4789
ip l s vxlan12_sut up
ip a a 20.10.110.2/24 dev vxlan12_sut
iperf3 -c 20.10.110.1 #should connect
Offload params: td_offset, cd_tunnel_params were
corrupted, due to l4 header pointing wrong address. NIC would then drop
those packets internally, due to incorrect TX descriptor data,
which increased GLV_TEPC register.
Fixes: 69e66c04c6 ("ice: Add mpls+tso support")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Legacy VLAN implementation allows for untrusted VF to have 8 VLAN
filters, not counting VLAN 0 filters. Current VLAN_V2 implementation
lowers available filters for VF, by counting in VLAN 0 filter for both
TPIDs.
Fix this by counting only non zero VLAN filters.
Without this patch, untrusted VF would not be able to access 8 VLAN
filters.
Fixes: cc71de8fa1 ("ice: Add support for VIRTCHNL_VF_OFFLOAD_VLAN_V2")
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Marek Szlosek <marek.szlosek@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add support for creating PPPoE filters in switchdev mode. Add support
for parsing PPPoE and PPP-specific tc options: pppoe_sid and ppp_proto.
Example filter:
tc filter add dev $PF1 ingress protocol ppp_ses prio 1 flower pppoe_sid \
1234 ppp_proto ip skip_sw action mirred egress redirect dev $VF1_PR
Changes in iproute2 are required to use the new fields.
ICE COMMS DDP package is required to create a filter as it contains PPPoE
profiles. Added a warning message when loaded DDP package does not contain
required profiles.
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the possibility to write raw bytes to the GNSS module through the
first TTY device. This allows user to configure the module.
Create a second read-only TTY device.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Add the possibility to write to connected i2c devices using the AQ
command. FW may reject the write if the device is not on allowlist.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
After commit 62b36c3ea6 ("PCI/AER: Remove
pci_cleanup_aer_uncorrect_error_status() calls"), calls to
pci_cleanup_aer_uncorrect_error_status() have already been removed. But in
commit 5995b6d0c6 ("ice: Implement pci_error_handler ops")
pci_cleanup_aer_uncorrect_error_status was used again, so remove it in
this patch.
Signed-off-by: Zhuo Chen <chenzhuo.1@bytedance.com>
Cc: Muchun Song <songmuchun@bytedance.com>
Cc: Sen Wang <wangsen.harry@bytedance.com>
Cc: Wenliang Wang <wangwenliang.1995@bytedance.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
External time stamp sources are supported only on certain devices. Enforce
the right support matrix by adding the ICE_F_PTP_EXTTS bit to the feature
bitmap set.
Co-developed-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Maciej Machnikowski <maciej.machnikowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When creating a snapshot of the NVM the driver needs to read the entire
contents from the NVM and store it. The NVM reads are protected by a lock
that is shared between the driver and the firmware.
If the driver takes too long to read the entire NVM (which can happen on
some systems) then the firmware could reclaim the lock and cause subsequent
reads from the driver to fail.
We could fix this by increasing the timeout that we pass to the firmware,
but we could end up in the same situation again if the system is slow.
Instead have the driver break the reading of the NVM into blocks that are
small enough that we have confidence that the read will complete within the
timeout time, but large enough not to cause significant AQ overhead.
Fixes: dce730f178 ("ice: add a devlink region for dumping NVM contents")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver currently presumes that the record data in the PLDM header
of the firmware image will match the device ID of the running device.
This is true for E810 devices. It appears that for E822 devices that
this is not guaranteed to be true.
Fix this by adding a check for the generic E822 device.
Fixes: d69ea414c9 ("ice: implement device flash update via devlink")
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
t-queue
Tony Nguyen says:
====================
100GbE Intel Wired LAN Driver Updates 2022-06-30
This series contains updates to ice driver only.
Martyna adds support for VLAN related TC switchdev filters and reworks
dummy packet implementation of VLANs to enable dynamic header insertion to
allow for more rule types.
Lu Wei utilizes eth_broadcast_addr() helper over an open coded version.
Ziyang Xuan removes unneeded NULL checks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Kbuild spotted the following bug during the testing of one of
the optimizations:
In file included from include/linux/cpumask.h:12,
[...]
from drivers/net/ethernet/intel/ice/ice_switch.c:4:
drivers/net/ethernet/intel/ice/ice_switch.c: In function 'ice_find_free_recp_res_idx.constprop':
include/linux/bitmap.h:447:22: warning: 'possible_idx[0]' is used uninitialized [-Wuninitialized]
447 | *map |= GENMASK(start + nbits - 1, start);
| ^~
In file included from drivers/net/ethernet/intel/ice/ice.h:7,
from drivers/net/ethernet/intel/ice/ice_lib.h:7,
from drivers/net/ethernet/intel/ice/ice_switch.c:4:
drivers/net/ethernet/intel/ice/ice_switch.c:4929:24: note: 'possible_idx[0]' was declared here
4929 | DECLARE_BITMAP(possible_idx, ICE_MAX_FV_WORDS);
| ^~~~~~~~~~~~
include/linux/types.h:11:23: note: in definition of macro 'DECLARE_BITMAP'
11 | unsigned long name[BITS_TO_LONGS(bits)]
| ^~~~
%ICE_MAX_FV_WORDS is 48, so bitmap_set() here was initializing only
48 bits, leaving a junk in the rest 16.
It was previously hidden due to that filling 48 bits makes
bitmap_set() call external __bitmap_set(), but after making it use
plain bit arithmetics on small bitmaps, compilers started seeing
the issue. It was still working because those 16 weren't used
anywhere anyhow.
bitmap_{clear,set}() are not really intended to initialize bitmaps,
rather to modify already initialized ones, as they don't do anything
past the passed number of bits. The correct function to do this in
that particular case is bitmap_fill(), so use it here. It will do
`*possible_idx = ~0UL` instead of `*possible_idx |= GENMASK(47, 0)`,
not leaving anything in an undefined state.
Fixes: fd2a6b71e3 ("ice: create advanced switch recipe")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Signed-off-by: Yury Norov <yury.norov@gmail.com>
Since commit b37a466837 ("netdevice: add the case if dev is NULL"),
dev_put(NULL) is safe, check NULL before dev_put() is not needed.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Use eth_broadcast_addr() to set broadcast address instead of memset().
Signed-off-by: Lu Wei <luwei32@huawei.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable the support of creating all kinds of declared dummy packets
with the VLAN tags by inserting VLAN headers (single VLAN and QinQ
cases) if needed.
Decrease the number of declared dummy packets and increase in the
possible packet's combinations for adding switch rules.
This change enables support of creating filters that match both on
VLAN + tunnels properties in switchdev.
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable support for adding TC rules that filter on the VLAN tag type
in switchdev mode.
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Enable support for adding TC rules with both C-tag and S-tag that can
filter on the inner and outer VLAN in QinQ for basic packets (not
tunneled cases).
Signed-off-by: Wiktor Pilarczyk <wiktor.pilarczyk@intel.com>
Signed-off-by: Martyna Szapar-Mudlaw <martyna.szapar-mudlaw@intel.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
In current implementation ice_update_phy_type enables all link modes
for selected speed. This approach doesn't work for 1000M speeds,
because both copper (1000baseT) and optical (1000baseX) standards
cannot be enabled at once.
Fix this, by adding the function `ice_set_phy_type_from_speed()`
for 1000M speeds.
Fixes: 48cb27f2fd ("ice: Implement handlers for ethtool PHY/link operations")
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Adding two filters with same matching criteria ends up with
one rule in hardware with act = ICE_FWD_TO_VSI_LIST.
In order to remove them properly we have to keep the
information about vsi handle which is used in VSI bitmap
(ice_adv_fltr_mgmt_list_entry::vsi_list_info::vsi_map).
Fixes: 0d08a441fb ("ice: ndo_setup_tc implementation for PF")
Reported-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 34a897758e ("ice: Add support for inner etype in switchdev")
added the ability to match on inner ethertype. A side effect of that change
is that it is now impossible to add some filters for protocols which do not
contain inner ethtype field. tc requires the protocol field to be specified
when providing certain other options, e.g. src_ip. This is a problem in
case of GTP - when user wants to specify e.g. src_ip, they also need to
specify protocol in tc command (otherwise tc fails with: Illegal "src_ip").
Because GTP is a tunnel, the protocol field is treated as inner protocol.
GTP does not contain inner ethtype field and the filter cannot be added.
To fix this, ignore the ethertype field in case of GTP filters.
Fixes: 9a225f81f5 ("ice: Support GTP-U and GTP-C offload in switchdev")
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Tested-by: Sandeep Penigalapati <sandeep.penigalapati@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Disable VF's RX/TX queues, when VIRTCHNL_OP_CONFIG_VSI_QUEUES fail.
Not disabling them might lead to scenario, where PF driver leaves VF
queues enabled, when VF's VSI failed queue config.
In this scenario VF should not have RX/TX queues enabled. If PF failed
to set up VF's queues, VF will reset due to TX timeouts in VF driver.
Initialize iterator 'i' to -1, so if error happens prior to configuring
queues then error path code will not disable queue 0. Loop that
configures queues will is using same iterator, so error path code will
only disable queues that were configured.
Fixes: 77ca27c417 ("ice: add support for virtchnl_queue_select.[tx|rx]_queues bitmap")
Suggested-by: Slawomir Laba <slawomirx.laba@intel.com>
Signed-off-by: Przemyslaw Patynowski <przemyslawx.patynowski@intel.com>
Signed-off-by: Mateusz Palczewski <mateusz.palczewski@intel.com>
Tested-by: Konrad Jankowski <konrad0.jankowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
VLAN filtering features, that is C-Tag and S-Tag, in DVM mode must be
both enabled or disabled.
In case of turning off/on only one of the features, another feature must
be turned off/on automatically with issuing an appropriate message to
the kernel log.
Fixes: 1babaf77f4 ("ice: Advertise 802.1ad VLAN filtering and offloads for PF netdev")
Signed-off-by: Roman Storozhenko <roman.storozhenko@intel.com>
Co-developed-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Signed-off-by: Anatolii Gerasymenko <anatolii.gerasymenko@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The offset was being incorrectly calculated for E822 - that led to
collisions in choosing TX timestamp register location when more than
one port was trying to use timestamping mechanism.
In E822 one quad is being logically split between ports, so quad 0 is
having trackers for ports 0-3, quad 1 ports 4-7 etc. Each port should
have separate memory location for tracking timestamps. Due to error for
example ports 1 and 2 had been assigned to quad 0 with same offset (0),
while port 1 should have offset 0 and 1 offset 16.
Fix it by correctly calculating quad offset.
Fixes: 3a7496234d ("ice: implement basic E822 PTP support")
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
