Now that fw_devlink=on by default and fw_devlink supports interrupt
properties, the execution will never get to the point where
driver_deferred_probe_check_state() is called before the supplier has
probed successfully or before deferred probe timeout has expired.
So, delete the call and replace it with -ENODEV.
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Saravana Kannan <saravanak@google.com>
Link: https://lore.kernel.org/r/20220601070707.3946847-4-saravanak@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a driver for an interrupt controller is missing, of_irq_get()
returns -EPROBE_DEFER ad infinitum, causing
fwnode_mdiobus_phy_device_register(), and ultimately, the entire
of_mdiobus_register() call, to fail. In turn, any phy_connect() call
towards a PHY on this MDIO bus will also fail.
This is not what is expected to happen, because the PHY library falls
back to poll mode when of_irq_get() returns a hard error code, and the
MDIO bus, PHY and attached Ethernet controller work fine, albeit
suboptimally, when the PHY library polls for link status. However,
-EPROBE_DEFER has special handling given the assumption that at some
point probe deferral will stop, and the driver for the supplier will
kick in and create the IRQ domain.
Reasons for which the interrupt controller may be missing:
- It is not yet written. This may happen if a more recent DT blob (with
an interrupt-parent for the PHY) is used to boot an old kernel where
the driver didn't exist, and that kernel worked with the
vintage-correct DT blob using poll mode.
- It is compiled out. Behavior is the same as above.
- It is compiled as a module. The kernel will wait for a number of
seconds specified in the "deferred_probe_timeout" boot parameter for
user space to load the required module. The current default is 0,
which times out at the end of initcalls. It is possible that this
might cause regressions unless users adjust this boot parameter.
The proposed solution is to use the driver_deferred_probe_check_state()
helper function provided by the driver core, which gives up after some
-EPROBE_DEFER attempts, taking "deferred_probe_timeout" into consideration.
The return code is changed from -EPROBE_DEFER into -ENODEV or
-ETIMEDOUT, depending on whether the kernel is compiled with support for
modules or not.
Fixes: 66bdede495 ("of_mdio: Fix broken PHY IRQ in case of probe deferral")
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20220407165538.4084809-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The newly implemented fwnode_mdbiobus_register turned out to be
problematic - in case the fwnode_/of_/acpi_mdio are built as
modules, a dependency cycle can be observed during the depmod phase of
modules_install, eg.:
depmod: ERROR: Cycle detected: fwnode_mdio -> of_mdio -> fwnode_mdio
depmod: ERROR: Found 2 modules in dependency cycles!
OR:
depmod: ERROR: Cycle detected: acpi_mdio -> fwnode_mdio -> acpi_mdio
depmod: ERROR: Found 2 modules in dependency cycles!
A possible solution could be to rework fwnode_mdiobus_register,
so that to merge the contents of acpi_mdiobus_register and
of_mdiobus_register. However feasible, such change would
be very intrusive and affect huge amount of the of_mdiobus_register
users.
Since there are currently 2 users of ACPI and MDIO
(xgmac_mdio and mvmdio), withdraw the fwnode_mdbiobus_register
and roll back to a simple 'if' condition in affected drivers.
Fixes: 62a6ef6a99 ("net: mdiobus: Introduce fwnode_mdbiobus_register()")
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces a new helper function that
wraps acpi_/of_ mdiobus_register() and allows its
usage via common fwnode_ interface.
Fall back to raw mdiobus_register() in case CONFIG_FWNODE_MDIO
is not enabled, in order to satisfy compatibility
in all future user drivers.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the newly introduced helper to setup both the of_node and the
fwnode for a given device.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By mistake, the of_node of the MDIO device was not setup in the patch
linked below. As a consequence, any PHY driver that depends on the
of_node in its probe callback was not be able to successfully finish its
probe on a PHY, thus the Generic PHY driver was used instead.
Fix this by actually setting up the of_node.
Fixes: bc1bee3b87 ("net: mdiobus: Introduce fwnode_mdiobus_register_phy()")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce fwnode_mdiobus_register_phy() to register PHYs on the
mdiobus. From the compatible string, identify whether the PHY is
c45 and based on this create a PHY device instance which is
registered on the mdiobus.
Along with fwnode_mdiobus_register_phy() also introduce
fwnode_find_mii_timestamper() and fwnode_mdiobus_phy_device_register()
since they are needed.
While at it, also use the newly introduced fwnode operation in
of_mdiobus_phy_device_register().
Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Acked-by: Grant Likely <grant.likely@arm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
