1
0
Fork 0
mirror of synced 2025-03-06 20:59:54 +01:00
Commit graph

166 commits

Author SHA1 Message Date
Sherry Sun
707f816f25 tty: serial: fsl_lpuart: correct the count of break characters
The LPUART can't distinguish between a break signal and a framing error,
so need to count the break characters if there is a framing error and
received data is zero instead of the parity error.

Fixes: 5541a9bacf ("serial: fsl_lpuart: handle break and make sysrq work")
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220725050115.12396-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-07-28 10:35:32 +02:00
Shenwei Wang
070298c84e serial: fsl_lpuart: zero out parity bit in CS7 mode
The LPUART hardware doesn't zero out the parity bit on the received
characters. This behavior won't impact the use cases of CS8 because
the parity bit is the 9th bit which is not currently used by software.
But the parity bit for CS7 must be zeroed out by software in order to
get the correct raw data.

Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20220714185858.615373-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-07-28 10:34:04 +02:00
Ilpo Järvinen
0139da50dc serial: Embed rs485_supported to uart_port
Embed rs485_supported to uart_port to allow serial core to tweak it as
needed.

Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-07-08 15:14:09 +02:00
Ilpo Järvinen
ae50bb2752 serial: take termios_rwsem for ->rs485_config() & pass termios as param
To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-27 14:44:20 +02:00
Ilpo Järvinen
7195eefb38 serial: fsl_lpuart: Call core's sanitization and remove custom one
Serial core handles serial_rs485 sanitization. Remove custom
sanitization from lpuart_config_rs485.

This change loses dev_err when SER_RS485_RX_DURING_TX is set due to
incorrect configuration. Other drivers do not do similar prinout for
full-duplex case and it should be done in serial core if it is
desirable to notify on this condition. Personally, I doesn't see it
important because the kernel gracefully downgrades to half-duplex.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-31-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-10 13:49:57 +02:00
Ilpo Järvinen
07481f448b serial: fsl_lpuart: Fill in rs485_supported
Add information on supported serial_rs485 features.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-16-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-10 13:49:25 +02:00
Ilpo Järvinen
8322b1f527 serial: Add uart_rs485_config()
A few serial drivers make a call to rs485_config() themselves (all
these seem to relate to init). Convert them all to use a common helper
which makes it easy to make adjustments on tasks related to it as
serial_rs485 struct sanitization is going to be added.

In pci_fintek_setup() (in 8250_pci.c), the rs485_config() call was made
with NULL, however, it can be changed to pass uart_port's rs485 struct.
No other callers should pass NULL into rs485_config() so the NULL check
can now be eliminated.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-06-10 13:49:24 +02:00
Ilpo Järvinen
503f418b10 serial: fsl_lpuart: Remove unnecessary clearing for CRTSCTS
if (termios->c_cflag & CRTSCTS) guarantees that CRTSCTS is not ever set
in the else block so clearing it is unnecessary.

While at it, remove also one pair of extra parenthesis.

Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220513082906.11096-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-19 18:26:17 +02:00
Greg Kroah-Hartman
d6da35e0c6 Merge 5.18-rc7 into usb-next
We need the tty fixes in here as well, as we need to revert one of them :(

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-16 15:39:23 +02:00
Indan Zupancic
401fb66a35 fsl_lpuart: Don't enable interrupts too early
If an irq is pending when devm_request_irq() is called, the irq
handler will cause a NULL pointer access because initialisation
is not done yet.

Fixes: 9d7ee0e28d ("tty: serial: lpuart: avoid report NULL interrupt")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Indan Zupancic <Indan.Zupancic@mep-info.com>
Link: https://lore.kernel.org/r/20220505114750.45423-1-Indan.Zupancic@mep-info.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-05-05 23:00:21 +02:00
Sherry Sun
c1b4148135 tty: serial: fsl_lpuart: remove the count initialization as it is not needed
No need to initialize the count variable in lpuart_copy_rx_to_tty(),
so let's remove it here.

Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220418021844.29591-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-22 16:22:38 +02:00
Sherry Sun
f398e0aa32 tty: serial: fsl_lpuart: fix potential bug when using both of_alias_get_id and ida_simple_get
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.

    aliases {
	...
        serial0 = &lpuart4;
        serial1 = &lpuart5;
        serial2 = &lpuart6;
        serial3 = &lpuart7;
    }

So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.

Fixes: 3bc3206e1c ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15 11:41:12 +02:00
Lino Sanfilippo
e5d4d733fc serial: fsl_lpuart: remove redundant code in rs485_config functions
In uart_set_rs485_config() the serial core already ensures that only one of
both options RTS on send or RTS after send is set. It also assigns the
passed serial_rs485 struct to the uart port.

So remove the check and the assignment from the drivers rs485_config()
function to avoid redundancy.

Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-9-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-04-15 11:30:22 +02:00
Jiri Slaby
3f8bab174c serial: make uart_console_write->putchar()'s character an unsigned char
Currently, uart_console_write->putchar's second parameter (the
character) is of type int. It makes little sense, provided uart_console_write()
accepts the input string as "const char *s" and passes its content -- the
characters -- to putchar(). So switch the character's type to unsigned
char.

We don't use char as that is signed on some platforms. That would cause
troubles for drivers which (implicitly) cast the char to u16 when
writing to the device. Sign extension would happen in that case and the
value written would be completely different to the provided char. DZ is
an example of such a driver -- on MIPS, it uses u16 for dz_out in
dz_console_putchar().

Note we do the char -> uchar conversion implicitly in
uart_console_write(). Provided we do not change size of the data type,
sign extension does not happen there, so the problem is void.

This makes the types consistent and unified with the rest of the uart
layer, which uses unsigned char in most places already. One exception is
xmit_buf, but that is going to be converted later.

Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-03-03 15:06:31 +01:00
Sherry Sun
93cf538e23 tty: serial: fsl_lpuart: count tty buffer overruns
Added support for counting the tty buffer overruns in fsl_lpuart driver
like other uart drivers.

Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220111085130.5817-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-01-26 14:54:12 +01:00
Jesse Taube
443df57b31 tty: serial: fsl_lpuart: Add i.MXRT1050 support
Add support for i.MXRT1050's uart.

Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Link: https://lore.kernel.org/r/20211215220538.4180616-8-Mr.Bossman075@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-17 18:00:21 +01:00
Greg Kroah-Hartman
f5bced9f34 Merge 5.16-rc4 into tty-next
We need the tty/serial driver fixes in here as well.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-06 09:32:47 +01:00
Sherry Sun
ffccc78a58 tty: serial: fsl_lpuart: add timeout for wait_event_interruptible in .shutdown()
Use wait_event_interruptible in lpuart_dma_shutdown isn't a reasonable
behavior, since it may cause the system hang here if the condition
!sport->dma_tx_in_progress never to be true in some corner case, such as
when enable the flow control, the dma tx request may never be completed
due to the peer's CTS setting when run .shutdown().

So here change to use wait_event_interruptible_timeout instead of
wait_event_interruptible, the tx dma will be forcibly terminated if the
tx dma request cannot be completed within 300ms.
Considering the worst tx dma case is to have a 4K bytes tx buffer, which
would require about 300ms to complete when the baudrate is 115200.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211203030441.22873-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-12-03 14:00:05 +01:00
Alexander Stein
4e9679738a Revert "tty: serial: fsl_lpuart: drop earlycon entry for i.MX8QXP"
Revert commit b4b844930f ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-11-25 18:27:44 +01:00
Fugang Duan
bd5305dcab tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp
Do software reset for communication port on imx7ulp and imx8qxp after
the port is registered if the UART controller support the feature.

Do partition reset with LPUART's power on, LPUART registers will
keep the previous status, like on i.MX8QXP platform, which is not
expected action, so need to set the RST bit of GLOBAL register to reset
all uart internal logic and registers.

Currently, only i.MX7ULP and i.MX8QXP LPUART controllers include
global register that support the software reset.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210823091801.17447-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-08-26 14:49:20 +02:00
Fugang Duan
48422152a8 tty: serial: fsl_lpuart: enable two stop bits for lpuart32
Add two stop bits support.
User can run the command to enable two stop bits for test:
stty  cstopb  -F /dev/ttyLPx

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210823081733.31941-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-08-26 14:49:14 +02:00
Andy Duan
d5c3894844 tty: serial: fsl_lpuart: fix the wrong mapbase value
Register offset needs to be applied on mapbase also.
dma_tx/rx_request use the physical address of UARTDATA.
Register offset is currently only applied to membase (the
corresponding virtual addr) but not on mapbase.

Fixes: 24b1e5f0e8 ("tty: serial: lpuart: add imx7ulp support")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Adriana Reus <adriana.reus@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Andy Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20210819021033.32606-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-08-26 14:49:03 +02:00
Fugang Duan
88c1d2478e tty: serial: fsl_lpuart: check dma_tx_in_progress in tx dma callback
There have a corner case that tx DMA .callback() is coming after
.flush_buffer(), then .callback() should check dma_tx_in_progress
flag and return in directly.

Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Vipul Kumar <vipul_kumar@mentor.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210817100203.21300-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-08-18 16:05:27 +02:00
Sherry Sun
06e91df16f tty: serial: fsl_lpuart: fix the wrong return value in lpuart32_get_mctrl
Patch e60c2991f1 make the lpuart32_get_mctrl always return 0, actually
this will break the functions of device which use flow control such as
Bluetooth.
For lpuart32 plaform, the hardware can handle the CTS automatically.
So we should set TIOCM_CTS active. Also need to set CAR and DSR active.

Patch has been tested on lpuart32 platforms such as imx8qm and imx8ulp.

Fixes: e60c2991f1 ("serial: fsl_lpuart: remove RTSCTS handling from get_mctrl()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210729083109.31541-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-07-29 17:05:59 +02:00
Michael Walle
8cac2f6eb8 serial: fsl_lpuart: disable DMA for console and fix sysrq
SYSRQ doesn't work with DMA. This is because there is no error
indication whether a symbol had a framing error or not. Actually,
this is not completely correct, there is a bit in the data register
which is set in this case, but we'd have to read change the DMA access
to 16 bit and we'd need to post process the data, thus make the DMA
pointless in the first place.

Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-10-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:08:26 +02:00
Michael Walle
8a0c810d94 serial: fsl_lpuart: add loopback support
The LPUART can loop the RX and TX signal. Add support for it.

Please note, this was only tested on the 32 bit version of the LPUART.

Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-9-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:08:26 +02:00
Michael Walle
fa35407354 serial: fsl_lpuart: remove manual RTSCTS control from 8-bit LPUART
The LPUART doesn't have the ability to control the RTS or CTS line
manually. Instead it will set it automatically when data is send or
handle it when data is received. Thus drop the wrong code in set_mctrl.
For the 32 bit version this was already done in the commit 2b30efe2e8
("tty: serial: lpuart: Remove unnecessary code from set_mctrl"). Keep
the 8-bit version in sync and remove it there, too.

Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-8-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:08:26 +02:00
Michael Walle
e60c2991f1 serial: fsl_lpuart: remove RTSCTS handling from get_mctrl()
The wrong code in set_mctrl() was already removed in commit 2b30efe2e8
("tty: serial: lpuart: Remove unnecessary code from set_mctrl"), but the
code in get_mctrl() wasn't removed. It will not return the state of the
RTS or CTS line but whether automatic flow control is enabled, which is
wrong for the get_mctrl(). Thus remove it.

Fixes: 2b30efe2e8 ("tty: serial: lpuart: Remove unnecessary code from set_mctrl")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-7-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:08:26 +02:00
Michael Walle
5541a9bacf serial: fsl_lpuart: handle break and make sysrq work
Although there is already sysrq characters handling, a break condition
was never detected. Add support for it.

The LPUART can't distinguish between a framing error and a break
condition. We assume it is a break if the received data is all zero.

Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-6-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:08:26 +02:00
Michael Walle
5697df7322 serial: fsl_lpuart: split sysrq handling
Instead of uart_handle_sysrq_char() use uart_prepare_sysrq_char() and
uart_unlock_and_check_sysrq(). This will call handle_sysrq() without
holding the port lock, which in turn let us drop the spin_trylock hack.

Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-5-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:08:26 +02:00
Michael Walle
0d84f62220 serial: fsl_lpuart: don't restore interrupt state in ISR
>From commit 75f4e830fa ("serial: do not restore interrupt state in
sysrq helper"):

  Since commit 81e2073c17 ("genirq: Disable interrupts for force
  threaded handlers") interrupt handlers that are not explicitly
  requested as threaded are always called with interrupts disabled and
  there is no need to save the interrupt state when taking the port
  lock.

Apply this also to fsl_lpuart in prepartion for sysrq handling with
uart_unlock_and_check_sysrq().

Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-4-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:08:26 +02:00
Michael Walle
ec22c3eec5 serial: fsl_lpuart: use UARTDATA_MASK macro
Use the corresponding macro instead of the magic number. While at it,
drop the useless cast to "unsigned char".

Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:08:26 +02:00
Michael Walle
ccf08fd120 serial: fsl_lpuart: don't modify arbitrary data on lpuart32
lpuart_rx_dma_startup() is used for both the 8 bit and the 32 bit
version of the LPUART. Modify the UARTCR only for the 8 bit version.

Fixes: f4eef224a0 ("serial: fsl_lpuart: add sysrq support when using dma")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:08:26 +02:00
Sherry Sun
fcb10ee27f tty: serial: fsl_lpuart: fix the potential risk of division or modulo by zero
We should be very careful about the register values that will be used
for division or modulo operations, althrough the possibility that the
UARTBAUD register value is zero is very low, but we had better to deal
with the "bad data" of hardware in advance to avoid division or modulo
by zero leading to undefined kernel behavior.

Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210427021226.27468-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-05-13 16:07:57 +02:00
Fabio Estevam
e8372c4f51 serial: fsl_lpuart: Use of_device_get_match_data()
The retrieval of driver data via of_device_get_match_data() can make
the code simpler.

Use of_device_get_match_data() to simplify the code.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20210118124447.1632092-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2021-01-20 18:48:15 +01:00
Vladimir Oltean
c97f2a6fb3 tty: serial: fsl_lpuart: LS1021A has a FIFO size of 16 words, like LS1028A
Prior to the commit that this one fixes, the FIFO size was derived from
the read-only register LPUARTx_FIFO[TXFIFOSIZE] using the following
formula:

TX FIFO size = 2 ^ (LPUARTx_FIFO[TXFIFOSIZE] - 1)

The documentation for LS1021A is a mess. Under chapter 26.1.3 LS1021A
LPUART module special consideration, it mentions TXFIFO_SZ and RXFIFO_SZ
being equal to 4, and in the register description for LPUARTx_FIFO, it
shows the out-of-reset value of TXFIFOSIZE and RXFIFOSIZE fields as "011",
even though these registers read as "101" in reality.

And when LPUART on LS1021A was working, the "101" value did correspond
to "16 datawords", by applying the formula above, even though the
documentation is wrong again (!!!!) and says that "101" means 64 datawords
(hint: it doesn't).

So the "new" formula created by commit f77ebb241c has all the premises
of being wrong for LS1021A, because it relied only on false data and no
actual experimentation.

Interestingly, in commit c2f448cff2 ("tty: serial: fsl_lpuart: add
LS1028A support"), Michael Walle applied a workaround to this by manually
setting the FIFO widths for LS1028A. It looks like the same values are
used by LS1021A as well, in fact.

When the driver thinks that it has a deeper FIFO than it really has,
getty (user space) output gets truncated.

Many thanks to Michael for pointing out where to look.

Fixes: f77ebb241c ("tty: serial: fsl_lpuart: correct the FIFO depth size")
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201023013429.3551026-1-vladimir.oltean@nxp.com
Reviewed-by:Fugang Duan <fugang.duan@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-28 13:40:25 +01:00
Angelo Dureghello
f4eef224a0 serial: fsl_lpuart: add sysrq support when using dma
Add handling of magic sysrq keys when using dma/edma.

Tested by sending BREAK followed by a sysrq command inside
a 5 secs time window, by:

echo 1 > /proc/sys/kernel/sysrq

BREAK + h, t, e, b, c

Tested also sending a command after 5 secs after BREAK, that's
properly ignored.

Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20201004161144.1307174-1-angelo.dureghello@timesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-10-05 13:32:30 +02:00
Peng Fan
29788ab1d2 tty: serial: fsl_lpuart: fix lpuart32_poll_get_char
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.

Suggested-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30 14:29:36 +02:00
Peng Fan
9ea40db477 tty: serial: lpuart: fix lpuart32_write usage
The 2nd and 3rd parameter were wrongly used, and cause kernel abort when
doing kgdb debug.

Fixes: 1da17d7cf8 ("tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929091920.22612-1-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-09-30 14:29:21 +02:00
Fabio Estevam
c9fe14ac8b serial: fsl_lpuart: Fix typo in "transfer"
Fix two occurrences where "transfer" is spelled incorrectly.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200818224457.16507-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-08-28 10:26:47 +02:00
Vabhav Sharma
d10ee1d191 tty: serial: fsl_lpuart: minimum baud rate support
The formula for the baud rate is
baud rate = "baud clock / ((OSR+1) × SBR)

Algorithm used in function lpuart32_serial_setbrg() only changes
the SBR. Even with maxmum value put in, OSR stays at 0x7 and the
lowest baud rate would be ~ 2600 bps

Update the algorithm to allow driver operation at 1200,2400 or 600 bps

Signed-off-by: Vabhav Sharma <vabhav.sharma@nxp.com>
Link: https://lore.kernel.org/r/1593170434-13524-1-git-send-email-vabhav.sharma@oss.nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-06-27 13:52:29 +02:00
Anson Huang
b14109f302 tty: serial: fsl_lpuart: Use __maybe_unused instead of #if CONFIG_PM_SLEEP
Use __maybe_unused for power management related functions to simplify
the code.

Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Link: https://lore.kernel.org/r/1589547481-25932-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-15 15:46:29 +02:00
Lukas Wunner
c150c0f362 serial: Allow uart_get_rs485_mode() to return errno
We're about to amend uart_get_rs485_mode() to support a GPIO pin for
rs485 bus termination.  Retrieving the GPIO descriptor may fail, so
allow uart_get_rs485_mode() to return an errno and change all callers
to check for failure.

The GPIO descriptor is going to be stored in struct uart_port.  Pass
that struct to uart_get_rs485_mode() in lieu of a struct device and
struct serial_rs485, both of which are directly accessible from struct
uart_port.

A few drivers call uart_get_rs485_mode() before setting the struct
device pointer in struct uart_port.  Shuffle those calls around where
necessary.

[Heiko Stuebner did the ar933x_uart.c portion, hence his Signed-off-by.]

Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/271e814af4b0db3bffbbb74abf2b46b75add4516.1589285873.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-05-15 14:47:05 +02:00
Fabio Estevam
44da03628b serial: fsl_lpuart: Change DMA failure messages to debug level
Currently the following messages are seen when booting i.MX8QXP:

fsl-lpuart 5a060000.serial: DMA tx channel request failed, operating without tx DMA (-19)
fsl-lpuart 5a060000.serial: DMA rx channel request failed, operating without rx DMA (-19)

It is not really useful to have such messages on every boot, so change
them to debug level instead.

Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200416153453.18825-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-04-23 15:53:44 +02:00
Michael Walle
810bc0a5fa tty: serial: fsl_lpuart: make coverity happy
Coverity reports the following:

  var_compare_op: Comparing chan to null implies that chan might be null.

  1234        if (chan)
  1235                dmaengine_terminate_all(chan);
  1236

  Dereference after null check (FORWARD_NULL)
  var_deref_op: Dereferencing null pointer chan.

  1237        dma_unmap_sg(chan->device->dev, &sport->rx_sgl, 1, DMA_FROM_DEVICE);

Technically, this is correct. But lpuart_dma_rx_free() is guarded by
lpuart_dma_rx_use which is only true if there is a dma channel, see
lpuart_rx_dma_startup(). In any way, this looks bogus. So remove
the superfluous "if (chan)" check and make coverity happy.

Fixes: a092ab25fd ("tty: serial: fsl_lpuart: fix DMA mapping")
Signed-off-by: Michael Walle <michael@walle.cc>
Reported-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20200403174942.9594-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-04-16 16:12:34 +02:00
Michael Walle
d7c53fb081 tty: serial: fsl_lpuart: fix return value checking
The return value of lpuart_dma_tx_request() is an negative errno on
failure and zero on success.

Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-2-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-26 15:34:05 +01:00
Michael Walle
d0e7600b91 tty: serial: fsl_lpuart: move dma_request_chan()
Move dma_request_chan() out of the atomic context. First this call
should not be in the atomic context at all and second the
dev_info_once() may cause a hang because because the console takes this
spinlock, too.

Fixes: 159381df14 ("tty: serial: fsl_lpuart: fix DMA operation when using IOMMU")
Reported-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Tested-by: Leonard Crestez <leonard.crestez@nxp.com>
Link: https://lore.kernel.org/r/20200325090658.25967-1-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-26 15:34:05 +01:00
Michael Walle
e33253f3b7 tty: serial: fsl_lpuart: add LS1028A earlycon support
Add a early_console_setup() for the LS1028A SoC with 32bit, little
endian access. If the bootloader does a fixup of the clock-frequency
node the baudrate divisor register will automatically be set.

Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-5-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12 10:02:00 +01:00
Michael Walle
c2f448cff2 tty: serial: fsl_lpuart: add LS1028A support
The LS1028A uses little endian register access and has a different FIFO
size encoding.

Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-4-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12 10:02:00 +01:00
Michael Walle
a092ab25fd tty: serial: fsl_lpuart: fix DMA mapping
Use the correct device to request the DMA mapping. Otherwise the IOMMU
doesn't get the mapping and it will generate a page fault.

The error messages look like:
[   19.012140] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xbbfff800, fsynr=0x3e0021, cbfrsynra=0x828, cb=9
[   19.023593] arm-smmu 5000000.iommu: Unhandled context fault: fsr=0x402, iova=0xbbfff800, fsynr=0x3e0021, cbfrsynra=0x828, cb=9

This was tested on a custom board with a LS1028A SoC.

Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20200306214433.23215-3-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2020-03-12 10:02:00 +01:00