While the rest of the generic DWC PCIe code uses the dedicated IO-mem
accessors, the dw_pcie_link_up() method for some unobvious reason directly
calls readl() to get PortLogic.DEBUG1 register content. Since the way the
DBI bus is accessed can be platform-specific, use dw_pcie_readl_dbi()
instead so dw_pcie_link_up() is slightly more generic.
Link: https://lore.kernel.org/r/20220624143428.8334-11-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
The unrolled version of the internal ATU has been available since the DWC
PCIe v4.80a IP core, but it may not be enabled. Per [1], if unrolled ATU
is enabled, the PCIE_ATU_VIEWPORT does not exist and reads as 0xffffffff;
while if unrolled ATU is disabled, PCIE_ATU_VIEWPORT will contain some
zeros.
Simplify dw_pcie_iatu_unroll_enabled() by checking the value of
PCIE_ATU_VIEWPORT.
[1] DesignWare Cores, PCI Express Controller, Register Desciptions,
v.4.90a, December 2016, p.855
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20220624143428.8334-10-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
If the "snps,enable-cdm-check" property exists, we should enable the CDM
check. But previously dw_pcie_setup() could exit before doing so if the
"num-lanes" property was absent or invalid.
Move the CDM enable earlier so we do it regardless of whether "num-lanes"
is present.
[bhelgaas: commit log]
Fixes: 07f123def7 ("PCI: dwc: Add support to enable CDM register check")
Link: https://lore.kernel.org/r/20220624143428.8334-7-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
If dw_pcie_ep_init() fails to perform any action after the EPC memory is
initialized and the MSI memory region is allocated, the latter parts won't
be undone thus causing a memory leak. Add a cleanup-on-error path to fix
these leaks.
[bhelgaas: commit log]
Fixes: 2fd0c9d966 ("PCI: designware-ep: Pre-allocate memory for MSI in dw_pcie_ep_init")
Link: https://lore.kernel.org/r/20220624143428.8334-6-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
We program the 64-bit ATU limit address (in PCIE_ATU_LIMIT/
PCIE_ATU_UPPER_LIMIT or PCIE_ATU_UNR_LOWER_LIMIT/PCIE_ATU_UNR_UPPER_LIMIT),
but in addition, the PCIE_ATU_INCREASE_REGION_SIZE bit must be set if the
upper 32 bits of the limit address differ from the upper 32 bits of the
base address (see [1,2]).
5b4cf0f653 ("PCI: dwc: Add upper limit address for outbound iATU") set
PCIE_ATU_INCREASE_REGION_SIZE, but only when the *size* was greater than
4GB. It did not set it when a smaller region crossed a 4GB boundary, e.g.,
[mem 0x0_f0000000-0x1_0fffffff].
Set PCIE_ATU_INCREASE_REGION_SIZE whenever PCIE_ATU_UPPER_LIMIT is
greater than PCIE_ATU_UPPER_BASE.
[1] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-36, p.175
[2] DesignWare Cores PCI Express Controller Databook - DWC PCIe Root Port,
v5.40a, March 2019, fig.3-37, p.176
[bhelgaas: commit log]
Fixes: 5b4cf0f653 ("PCI: dwc: Add upper limit address for outbound iATU")
Link: https://lore.kernel.org/r/20220624143428.8334-5-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Some DWC-based controllers (e.g., pcie-al.c and pci-keystone.c, identified
by the fact that they override the default dw_child_pcie_ops) use their own
address translation approach instead of the DWC internal ATU (iATU). For
those controllers, skip disabling the iATU outbound windows.
[bhelgaas: commit log, update multiple window comment]
Fixes: 458ad06c4c ("PCI: dwc: Ensure all outbound ATU windows are reset")
Link: https://lore.kernel.org/r/20220624143428.8334-4-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
dw_pcie_disable_atu() was introduced by f8aed6ec62 ("PCI: dwc:
designware: Add EP mode support") and supported only the viewport version
of the iATU CSRs.
DW PCIe IP cores v4.80a and newer also support unrolled iATU/eDMA space.
Callers of dw_pcie_disable_atu(), including pci_epc_ops.clear_bar(),
pci_epc_ops.unmap_addr(), and dw_pcie_setup_rc(), don't work correctly when
it is enabled.
Add dw_pcie_disable_atu() support for controllers with unrolled iATU CSRs
enabled.
[bhelgaas: commit log]
Fixes: f8aed6ec62 ("PCI: dwc: designware: Add EP mode support")
Link: https://lore.kernel.org/r/20220624143428.8334-3-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
It's logically correct to undo everything that was done when an error is
discovered or in the corresponding cleanup counterpart. Otherwise the host
controller will be left in an undetermined state. Since the link is set up
in the host_init method, deactivate it there in the cleanup-on-error block
and stop the link in the antagonistic routine - dw_pcie_host_deinit(). Link
deactivation is platform-specific and should be implemented in
dw_pcie_ops.stop_link().
Fixes: 886a9c1347 ("PCI: dwc: Move link handling into common code")
Link: https://lore.kernel.org/r/20220624143428.8334-2-Sergey.Semin@baikalelectronics.ru
Tested-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
pm_runtime_enable() will increase power disable depth. If
dw_pcie_ep_init() fails, we should use pm_runtime_disable() to balance it
with pm_runtime_enable().
Add missing pm_runtime_disable() for tegra_pcie_config_ep().
Fixes: c57247f940 ("PCI: tegra: Add support for PCIe endpoint mode in Tegra194")
Link: https://lore.kernel.org/r/20220602031910.55859-1-linmq006@gmail.com
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
-----BEGIN PGP SIGNATURE-----
iQJIBAABCgAyFiEEgMe7l+5h9hnxdsnuWYigwDrT+vwFAmKP/tQUHGJoZWxnYWFz
QGdvb2dsZS5jb20ACgkQWYigwDrT+vzH0xAAojQowrSWzZ5FKTqI+L/L9ZXoAb+e
9IvQljKc9taJldmXp+EB9wkS/5B+VtQcC2qUQuWEQXUoECF8qHlcB4l+XQyd1tWO
O0vZxETH22xjLLrjG2F3l5rrfkJZAf2nEugwbDk97YEgiimeOiRcv3bx6AUCtj6I
rPJ13Fop3Jke7sQMcXYJe3gQLT1o1AKiQGghiCFNi/gzx2lXI6mmHBgLxFoiqcby
WpfXbvbJti95HRaahUR3HaDFfHj4HVkQNLlTtIykJ3Tl2/rOhWEJjI8JOIQpAA+M
WBrWw9rfgbScTiGV+dZ3h7hKiPnHKl9YETIX7L0oA2sj0jZcIs0d6mSBZx0kYuI9
eAlx+qSK9xpbQQr/fdYaUdF1q4QdtU0BYOvOWOzWsqYCECMRJ1PUHFSMbmR/+PNB
P5lHnAbggRSoxdAtwFYv1HTr+VpGH9S+5oxHCz3ohpMjYy6mkCZwHpZn3doaU3ci
KG6yIoVKftm3fZdtFvL03qHl/I8+X24ZhT/T/278PRGjkhSyr56hZo8hg0gqqTct
ngip8qNABmSbqpr73/W6Vl42zAbYtNk1BykYahbKupgW8FbT7hqaZTB05V87pVu+
Ko1aJM6VoOP9rMlKHI9ba8eYCzDrZbLZUFn7ljNPDpzutf0tAwtgwzvZBXN3za6+
Z9+D5dxmvrZEIbA=
=hEti
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Resource management:
- Restrict E820 clipping to PCI host bridge windows (Bjorn Helgaas)
- Log E820 clipping better (Bjorn Helgaas)
- Add kernel cmdline options to enable/disable E820 clipping (Hans de
Goede)
- Disable E820 reserved region clipping for IdeaPads, Yoga, Yoga
Slip, Acer Spin 5, Clevo Barebone systems where clipping leaves no
usable address space for touchpads, Thunderbolt devices, etc (Hans
de Goede)
- Disable E820 clipping by default starting in 2023 (Hans de Goede)
PCI device hotplug:
- Include files to remove implicit dependencies (Christophe Leroy)
- Only put Root Ports in D3 if they can signal and wake from D3 so
AMD Yellow Carp doesn't miss hotplug events (Mario Limonciello)
Power management:
- Define pci_restore_standard_config() only for CONFIG_PM_SLEEP since
it's unused otherwise (Krzysztof Kozlowski)
- Power up devices completely, including anything platform firmware
needs to do, during runtime resume (Rafael J. Wysocki)
- Move pci_resume_bus() to PM callbacks so we observe the required
bridge power-up delays (Rafael J. Wysocki)
- Drop unneeded runtime_d3cold device flag (Rafael J. Wysocki)
- Split pci_raw_set_power_state() between pci_power_up() and a new
pci_set_low_power_state() (Rafael J. Wysocki)
- Set current_state to D3cold if config read returns ~0, indicating
the device is not accessible (Rafael J. Wysocki)
- Do not call pci_update_current_state() from pci_power_up() so BARs
and ASPM config are restored correctly (Rafael J. Wysocki)
- Write 0 to PMCSR in pci_power_up() in all cases (Rafael J. Wysocki)
- Split pci_power_up() to pci_set_full_power_state() to avoid some
redundant operations (Rafael J. Wysocki)
- Skip restoring BARs if device is not in D0 (Rafael J. Wysocki)
- Rearrange and clarify pci_set_power_state() (Rafael J. Wysocki)
- Remove redundant BAR restores from pci_pm_thaw_noirq() (Rafael J.
Wysocki)
Virtualization:
- Acquire device lock before config space access lock to avoid AB/BA
deadlock with sriov_numvfs_store() (Yicong Yang)
Error handling:
- Clear MULTI_ERR_COR/UNCOR_RCV bits, which a race could previously
leave permanently set (Kuppuswamy Sathyanarayanan)
Peer-to-peer DMA:
- Whitelist Intel Skylake-E Root Ports regardless of which devfn they
are (Shlomo Pongratz)
ASPM:
- Override L1 acceptable latency advertised by Intel DG2 so ASPM L1
can be enabled (Mika Westerberg)
Cadence PCIe controller driver:
- Set up device-specific register to allow PTM Responder to be
enabled by the normal architected bit (Christian Gmeiner)
- Override advertised FLR support since the controller doesn't
implement FLR correctly (Parshuram Thombare)
Cadence PCIe endpoint driver:
- Correct bitmap size for the ob_region_map of outbound window usage
(Dan Carpenter)
Freescale i.MX6 PCIe controller driver:
- Fix PERST# assertion/deassertion so we observe the required delays
before accessing device (Francesco Dolcini)
Freescale Layerscape PCIe controller driver:
- Add "big-endian" DT property (Hou Zhiqiang)
- Update SCFG DT property (Hou Zhiqiang)
- Add "aer", "pme", "intr" DT properties (Li Yang)
- Add DT compatible strings for ls1028a (Xiaowei Bao)
Intel VMD host bridge driver:
- Assign VMD IRQ domain before enumeration to avoid IOMMU interrupt
remapping errors when MSI-X remapping is disabled (Nirmal Patel)
- Revert VMD workaround that kept MSI-X remapping enabled when IOMMU
remapping was enabled (Nirmal Patel)
Marvell MVEBU PCIe controller driver:
- Add of_pci_get_slot_power_limit() to parse the
'slot-power-limit-milliwatt' DT property (Pali Rohár)
- Add mvebu support for sending Set_Slot_Power_Limit message (Pali
Rohár)
MediaTek PCIe controller driver:
- Fix refcount leak in mtk_pcie_subsys_powerup() (Miaoqian Lin)
MediaTek PCIe Gen3 controller driver:
- Reset PHY and MAC at probe time (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add chained_irq_enter()/chained_irq_exit() calls to mc_handle_msi()
and mc_handle_intx() to avoid lost interrupts (Conor Dooley)
- Fix interrupt handling race (Daire McNamara)
NVIDIA Tegra194 PCIe controller driver:
- Drop tegra194 MSI register save/restore, which is unnecessary since
the DWC core does it (Jisheng Zhang)
Qualcomm PCIe controller driver:
- Add SM8150 SoC DT binding and support (Bhupesh Sharma)
- Fix pipe clock imbalance (Johan Hovold)
- Fix runtime PM imbalance on probe errors (Johan Hovold)
- Fix PHY init imbalance on probe errors (Johan Hovold)
- Convert DT binding to YAML (Dmitry Baryshkov)
- Update DT binding to show that resets aren't required for
MSM8996/APQ8096 platforms (Dmitry Baryshkov)
- Add explicit register names per chipset in DT binding (Dmitry
Baryshkov)
- Add sc7280-specific clock and reset definitions to DT binding
(Dmitry Baryshkov)
Rockchip PCIe controller driver:
- Fix bitmap size when searching for free outbound region (Dan
Carpenter)
Rockchip DesignWare PCIe controller driver:
- Remove "snps,dw-pcie" from rockchip-dwc DT "compatible" property
because it's not fully compatible with rockchip (Peter Geis)
- Reset rockchip-dwc controller at probe (Peter Geis)
- Add rockchip-dwc INTx support (Peter Geis)
Synopsys DesignWare PCIe controller driver:
- Return error instead of success if DMA mapping of MSI area fails
(Jiantao Zhang)
Miscellaneous:
- Change pci_set_dma_mask() documentation references to
dma_set_mask() (Alex Williamson)"
* tag 'pci-v5.19-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (64 commits)
dt-bindings: PCI: qcom: Add schema for sc7280 chipset
dt-bindings: PCI: qcom: Specify reg-names explicitly
dt-bindings: PCI: qcom: Do not require resets on msm8996 platforms
dt-bindings: PCI: qcom: Convert to YAML
PCI: qcom: Fix unbalanced PHY init on probe errors
PCI: qcom: Fix runtime PM imbalance on probe errors
PCI: qcom: Fix pipe clock imbalance
PCI: qcom: Add SM8150 SoC support
dt-bindings: pci: qcom: Document PCIe bindings for SM8150 SoC
x86/PCI: Disable E820 reserved region clipping starting in 2023
x86/PCI: Disable E820 reserved region clipping via quirks
x86/PCI: Add kernel cmdline options to use/ignore E820 reserved regions
PCI: microchip: Fix potential race in interrupt handling
PCI/AER: Clear MULTI_ERR_COR/UNCOR_RCV bits
PCI: cadence: Clear FLR in device capabilities register
PCI: cadence: Allow PTM Responder to be enabled
PCI: vmd: Revert 2565e5b69c ("PCI: vmd: Do not disable MSI-X remapping if interrupt remapping is enabled by IOMMU.")
PCI: vmd: Assign VMD IRQ domain before enumeration
PCI: Avoid pci_dev_lock() AB/BA deadlock with sriov_numvfs_store()
PCI: rockchip-dwc: Add legacy interrupt support
...
Drop the leftover pm_runtime_disable() calls from the late probe error
paths that would, for example, prevent runtime PM from being reenabled
after a probe deferral.
Link: https://lore.kernel.org/r/20220401133854.10421-2-johan+linaro@kernel.org
Fixes: 6e5da6f7d8 ("PCI: qcom: Fix error handling in runtime PM support")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: stable@vger.kernel.org # 4.20
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Fix a clock imbalance introduced by ed8cc3b1fc ("PCI: qcom: Add support
for SDM845 PCIe controller"), which enables the pipe clock both in init()
and in post_init() but only disables in post_deinit().
Note that the pipe clock was also never disabled in the init() error
paths and that enabling the clock before powering up the PHY looks
questionable.
Link: https://lore.kernel.org/r/20220401133351.10113-1-johan+linaro@kernel.org
Fixes: ed8cc3b1fc ("PCI: qcom: Add support for SDM845 PCIe controller")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: stable@vger.kernel.org # 5.6
The PCIe IP (rev 1.5.0) on SM8150 SoC is similar to the one used on
SM8250. Add SM8150 support, reusing the members of ops_1_9_0.
Link: https://lore.kernel.org/r/20220326060810.1797516-3-bhupesh.sharma@linaro.org
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Vinod Koul <vkoul@kernel.org>
The legacy interrupts on the rk356x PCIe controller are handled by a
single muxed interrupt. Add IRQ domain support to the pcie-dw-rockchip
driver to support the virtual domain.
Link: https://lore.kernel.org/r/20220429123832.2376381-4-pgwipeout@gmail.com
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Marc Zyngier <maz@kernel.org>
The PCIe controller is in an unknown state at driver probe. This can
lead to undesireable effects when the driver attempts to configure the
controller.
Prevent issues in the future by resetting the core during probe.
Link: https://lore.kernel.org/r/20220429123832.2376381-3-pgwipeout@gmail.com
Tested-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Peter Geis <pgwipeout@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
According to the PCIe standard the PERST# signal (reset-gpio in
fsl,imx* compatible dts) should be kept asserted for at least 100 usec
before the PCIe refclock is stable, should be kept asserted for at
least 100 msec after the power rails are stable and the host should wait
at least 100 msec after it is de-asserted before accessing the
configuration space of any attached device.
From PCIe CEM r2.0, sec 2.6.2
T-PVPERL: Power stable to PERST# inactive - 100 msec
T-PERST-CLK: REFCLK stable before PERST# inactive - 100 usec.
From PCIe r5.0, sec 6.6.1
With a Downstream Port that does not support Link speeds greater than
5.0 GT/s, software must wait a minimum of 100 ms before sending a
Configuration Request to the device immediately below that Port.
Failure to do so could prevent PCIe devices to be working correctly,
and this was experienced with real devices.
Move reset assert to imx6_pcie_assert_core_reset(), this way we ensure
that PERST# is asserted before enabling any clock, move de-assert to the
end of imx6_pcie_deassert_core_reset() after the clock is enabled and
deemed stable and add a new delay of 100 msec just afterward.
Link: https://lore.kernel.org/all/20220211152550.286821-1-francesco.dolcini@toradex.com
Link: https://lore.kernel.org/r/20220404081509.94356-1-francesco.dolcini@toradex.com
Fixes: bb38919ec5 ("PCI: imx6: Add support for i.MX6 PCIe controller")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Richard Zhu <hongxing.zhu@nxp.com>
Remove code duplication by moving the code related to enabling/disabling
the resources (PHY, CLK, Reset) to common functions so that they can be
called from multiple places.
[mani: renamed the functions and reworded the commit message]
Link: https://lore.kernel.org/r/20220502104938.97033-1-manivannan.sadhasivam@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
The Qualcomm SC8180X platform was piggy-backing on the SM8250
qcom_pcie_cfg, but SC8180X doesn't have the ddrss_sf_tbu clock, so
it now fails to probe due to the missing clock.
Give SC8180X its own qcom_pcie_cfg, without the ddrss_sf_tbu flag set.
Fixes: 0614f98bbb ("PCI: qcom: Add ddrss_sf_tbu flag")
Link: https://lore.kernel.org/r/20220331013415.592748-1-bjorn.andersson@linaro.org
Tested-by: Steev Klimaszewski <steev@kali.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
The integrated MSI Receiver enable register is always initialized in
dw_pcie_setup_rc() which is also called in resume code path, so we
don't need to save/restore the enable register during suspend/resume.
Link: https://lore.kernel.org/r/20211226074910.2722-1-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Vidya Sagar <vidyas@nvidia.com>
When dma_mapping_error() returns error because of no enough memory,
but dw_pcie_host_init() returns success, which will mislead the callers.
Link: https://lore.kernel.org/r/30170911-0e2f-98ce-9266-70465b9073e5@huawei.com
Fixes: 07940c369a ("PCI: dwc: Fix MSI page leakage in suspend/resume")
Signed-off-by: Jianrong Zhang <zhangjianrong5@huawei.com>
Signed-off-by: Jiantao Zhang <water.zhangjiantao@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
-----BEGIN PGP SIGNATURE-----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=5Q9H
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Move the VGA arbiter from drivers/gpu to drivers/pci because it's
PCI-specific, not GPU-specific (Bjorn Helgaas)
- Select the default VGA device consistently whether it's enumerated
before or after VGA arbiter init, which fixes arches that enumerate
PCI devices late (Huacai Chen)
Resource management:
- Support BAR sizes up to 8TB (Dongdong Liu)
PCIe native device hotplug:
- Fix "Command Completed" tracking to avoid spurious timouts when
powering off empty slots (Liguang Zhang)
- Quirk Qualcomm devices that don't implement Command Completed
correctly, again to avoid spurious timeouts (Manivannan Sadhasivam)
Peer-to-peer DMA:
- Add Intel 3rd Gen Intel Xeon Scalable Processors to whitelist
(Michael J. Ruhl)
APM X-Gene PCIe controller driver:
- Revert generic DT parsing changes that broke some machines in the
field (Marc Zyngier)
Freescale i.MX6 PCIe controller driver:
- Allow controller probe to succeed even when no devices currently
present to allow hot-add later (Fabio Estevam)
- Enable power management on i.MX6QP (Richard Zhu)
- Assert CLKREQ# on i.MX8MM so enumeration doesn't hang when no
device is connected (Richard Zhu)
Marvell Aardvark PCIe controller driver:
- Fix MSI and MSI-X support (Marek Behún, Pali Rohár)
- Add support for ERR and PME interrupts (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Add DT binding and support for "num-lanes" (Pali Rohár)
- Add support for INTx interrupts (Pali Rohár)
Microsoft Hyper-V host bridge driver:
- Avoid unnecessary hypercalls when unmasking IRQs on ARM64 (Boqun
Feng)
Qualcomm PCIe controller driver:
- Add SM8450 DT binding and driver support (Dmitry Baryshkov)
Renesas R-Car PCIe controller driver:
- Help the controller get to the L1 state since the hardware can't do
it on its own (Marek Vasut)
- Return PCI_ERROR_RESPONSE (~0) for reads that fail on PCIe (Marek
Vasut)
SiFive FU740 PCIe controller driver:
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe (Ben Dooks)
Socionext UniPhier Pro5 controller driver:
- Add NX1 DT binding and driver support (Kunihiko Hayashi)
Synopsys DesignWare PCIe controller driver:
- Restore MSI configuration so MSI works after resume (Jisheng
Zhang)"
* tag 'pci-v5.18-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (94 commits)
x86/PCI: Add #includes to asm/pci_x86.h
PCI: ibmphp: Remove unused assignments
PCI: cpqphp: Remove unused assignments
PCI: fu740: Remove unused assignments
PCI: kirin: Remove unused assignments
PCI: Remove unused assignments
PCI: Declare pci_filp_private only when HAVE_PCI_MMAP
PCI: Avoid broken MSI on SB600 USB devices
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: xgene: Revert "PCI: xgene: Fix IB window setup"
PCI: xgene: Revert "PCI: xgene: Use inbound resources for setup"
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: rcar: Use PCI_SET_ERROR_RESPONSE after read which triggered an exception
PCI: rcar: Finish transition to L1 state in rcar_pcie_config_access()
PCI: dwc: Restore MSI Receiver mask during resume
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
PCI/VGA: Replace full MIT license text with SPDX identifier
PCI/VGA: Use unsigned format string to print lock counts
PCI/VGA: Log bridge control messages when adding devices
...
- Save pointer to device match data instead of copying it (Dmitry
Baryshkov)
- Add ddrss_sf_tbu flag to device match data instead of checking OF
compatible string (Dmitry Baryshkov)
- Add SM8450 SoC PCIe DT bindings (Dmitry Baryshkov)
- Add SM8450 PCIe support (Dmitry Baryshkov)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Add SM8450 PCIe support
PCI: qcom: Add ddrss_sf_tbu flag
PCI: qcom: Remove redundancy between qcom_pcie and qcom_pcie_cfg
dt-bindings: pci: qcom: Document PCIe bindings for SM8450
- Allow host controller driver to probe successfully (as other drivers do)
even if link is currently down (Fabio Estevam)
- Enable i.MX6QP PCIe power management (Richard Zhu)
- Invoke PHY exit function after PHY power off (Richard Zhu)
- Assert i.MX8MM CLKREQ# even if no device present to avoid boot hangs
(Richard Zhu)
* remotes/lorenzo/pci/imx6:
PCI: imx6: Assert i.MX8MM CLKREQ# even if no device present
PCI: imx6: Invoke the PHY exit function after PHY power off
PCI: imx6: Enable i.MX6QP PCIe power management support
PCI: imx6: Allow to probe when dw_pcie_wait_for_link() fails
- Drop redundant '-gpios' from DT GPIO lookup (Ben Dooks)
- Force 2.5GT/s for initial device probe to workaround enumeration issue on
SiFive Unmatched board (Ben Dooks)
* pci/host/fu740:
PCI: fu740: Force 2.5GT/s for initial device probe
PCI: fu740: Drop redundant '-gpios' from DT GPIO lookup
fu740_pcie_host_init() assigned "ret", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-fu740.c:227 Variable 'ret' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-4-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
hi3660_pcie_phy_init() assigned "pdev", but never used the value. Drop it.
Found by Krzysztof using cppcheck:
$ cppcheck --enable=all --force
unreadVariable drivers/pci/controller/dwc/pcie-kirin.c:336 Variable 'pdev' is assigned a value that is never used.
Reported-by: Krzysztof Wilczyński <kw@linux.com>
Link: https://lore.kernel.org/r/20220313192933.434746-3-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The fu740 PCIe core does not probe any devices on the SiFive Unmatched
board without this fix (or having U-Boot explicitly start the PCIe via
either boot-script or user command). The fix is to start the link at
2.5GT/s speeds and once the link is up then change the maximum speed back
to the default.
The U-Boot driver claims to set the link-speed to 2.5GT/s to get the probe
to work (and U-Boot does print link up at 2.5GT/s) in the following code:
https://source.denx.de/u-boot/u-boot/-/blob/master/drivers/pci/pcie_dw_sifive.c?id=v2022.01#L271
Link: https://lore.kernel.org/r/20220318152430.526320-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Palmer Dabbelt <palmer@rivosinc.com>
The CLKREQ# signal is an open drain, active low signal that is driven
low by the remote Endpoint device. But it might not be driven low if no
Endpoint device is connected.
On i.MX8MM PCIe, phy_init() may fail and system boot may hang if no
Endpoint is connected to assert CLKREQ#.
Handle this as on i.MX8MQ, where we explicitly assert CLKREQ# so the
PHY can be initialized.
Link: https://lore.kernel.org/r/1645672013-8949-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
To balance phy->init_count, invoke the phy_exit() after phy_power_off().
Link: https://lore.kernel.org/r/1646289275-17813-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 178e244cb6 ("PCI: imx: Add the imx8mm pcie support")
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
If a host that uses the IP's integrated MSI Receiver lost power
during suspend, we call dw_pcie_setup_rc() to reinit the RC. But
dw_pcie_setup_rc() always sets pp->irq_mask[ctrl] to ~0, so the mask
register is always set as 0xffffffff incorrectly, thus the MSI can't
work after resume.
Fix this issue by moving pp->irq_mask[ctrl] initialization to
dw_pcie_host_init() so we can correctly set the mask reg during both
boot and resume.
Tested-by: Richard Zhu <hongxing.zhu@nxp.com>
Link: https://lore.kernel.org/r/20211226074019.2556-1-jszhang@kernel.org
Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The calls to devm_gpiod_get_optional() have the -gpios at the end of the
name but the GPIO core code is already adding the suffix during the lookup.
This means the PCIe driver is not finding the necessary reset or power
lines to allow initialisation of the PCIe.
Drop the redundant '-gpios' when we look up GPIOs from the DT.
This bug has not been noticed because if U-Boot has setup the GPIO lines
for the hardware when it does the PCIe initialisation (either by booting
from PCIe or user command to access PCIe) then the PCIe will work in Linux.
The U-Boot as supplied by SiFive does not by default initialise any PCIe
component.
Link: https://lore.kernel.org/r/20220221210347.1335004-1-ben.dooks@codethink.co.uk
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
i.MX6QP PCIe supports the reset logic, thus it can reset itself to the
initialized state when exit from L2 or L3 states.
Enable the i.MX6QP PCIe suspend/resume operations support.
Link: https://lore.kernel.org/r/1645425237-4071-2-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
On SM8450 platform PCIe hosts do not use all the clocks (and add several
additional clocks), so expand the driver to handle these requirements.
PCIe0 and PCIe1 hosts use different sets of clocks, so separate entries
are required.
Link: https://lore.kernel.org/r/20220223101435.447839-5-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Qualcomm PCIe driver uses compatible string to check if the ddrss_sf_tbu
clock should be used. Since sc7280 support has added flags, switch to
the new mechanism to check if this clock should be used.
Link: https://lore.kernel.org/r/20220223101435.447839-4-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
In preparation to adding more flags to configuration data, use pointer
to struct qcom_pcie_cfg directly inside struct qcom_pcie, rather than
duplicating all its fields. This would save us from the boilerplate code
that just copies flag values from one struct to another one.
Link: https://lore.kernel.org/r/20220223101435.447839-3-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Add these PCI class codes to pci_ids.h:
PCI_CLASS_BRIDGE_PCI_NORMAL
PCI_CLASS_BRIDGE_PCI_SUBTRACTIVE
Use these defines in all kernel code for describing PCI class codes for
normal and subtractive PCI bridges.
[bhelgaas: similar change in pci-mvebu.c]
Link: https://lore.kernel.org/r/20220214114109.26809-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Add basic support for UniPhier NX1 SoC as non-legacy SoC. This includes
a compatible string, SoC-dependent data containing init() and wait()
functions for the controller.
Link: https://lore.kernel.org/r/1644480596-20037-4-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Define SoC data structure that includes pci_epc_features, SoC-dependent
callback functions and flags to distinguish the behavior of each SoC.
The callback functions define init() to initialize the controller and
wait() to wait until initialization is completed.
Rename uniphier_pcie_init_ep() to uniphier_pcie_pro5_init_ep() for
initializing PCIe controller implemented in Pro5 SoC. And Pro5 SoC
doesn't have wait() function.
Link: https://lore.kernel.org/r/1644480596-20037-3-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Bean reported that a622435fbe ("PCI: kirin: Prefer
of_device_get_match_data()") broke kirin_pcie_probe() because it assumed
match data of 0 was a failure when in fact, it meant the match data was
"(void *)PCIE_KIRIN_INTERNAL_PHY".
Therefore, probing of "hisilicon,kirin960-pcie" devices failed with -EINVAL
and an "OF data missing" message.
Add a struct kirin_pcie_data to encode the PHY type. Then the result of
of_device_get_match_data() should always be a non-NULL pointer to a struct
kirin_pcie_data that contains the PHY type.
Fixes: a622435fbe ("PCI: kirin: Prefer of_device_get_match_data()")
Link: https://lore.kernel.org/r/20220202162659.GA12603@bhelgaas
Link: https://lore.kernel.org/r/20220201215941.1203155-1-huobean@gmail.com
Reported-by: Bean Huo <beanhuo@micron.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The intention of commit 886a9c1347 ("PCI: dwc: Move link handling into
common code") was to standardize the behavior of link down as explained
in its commit log:
"The behavior for a link down was inconsistent as some drivers would fail
probe in that case while others succeed. Let's standardize this to
succeed as there are usecases where devices (and the link) appear later
even without hotplug. For example, a reconfigured FPGA device."
The pci-imx6 still fails to probe when the link is not present, which
causes the following warning:
imx6q-pcie 8ffc000.pcie: Phy link never came up
imx6q-pcie: probe of 8ffc000.pcie failed with error -110
------------[ cut here ]------------
WARNING: CPU: 0 PID: 30 at drivers/regulator/core.c:2257 _regulator_put.part.0+0x1b8/0x1dc
Modules linked in:
CPU: 0 PID: 30 Comm: kworker/u2:2 Not tainted 5.15.0-next-20211103 #1
Hardware name: Freescale i.MX6 SoloX (Device Tree)
Workqueue: events_unbound async_run_entry_fn
[<c0111730>] (unwind_backtrace) from [<c010bb74>] (show_stack+0x10/0x14)
[<c010bb74>] (show_stack) from [<c0f90290>] (dump_stack_lvl+0x58/0x70)
[<c0f90290>] (dump_stack_lvl) from [<c012631c>] (__warn+0xd4/0x154)
[<c012631c>] (__warn) from [<c0f87b00>] (warn_slowpath_fmt+0x74/0xa8)
[<c0f87b00>] (warn_slowpath_fmt) from [<c076b4bc>] (_regulator_put.part.0+0x1b8/0x1dc)
[<c076b4bc>] (_regulator_put.part.0) from [<c076b574>] (regulator_put+0x2c/0x3c)
[<c076b574>] (regulator_put) from [<c08c3740>] (release_nodes+0x50/0x178)
Fix this problem by ignoring the dw_pcie_wait_for_link() error like
it is done on the other dwc drivers.
Tested on imx6sx-sdb and imx6q-sabresd boards.
Link: https://lore.kernel.org/r/20220106103645.2790803-1-festevam@gmail.com
Fixes: 886a9c1347 ("PCI: dwc: Move link handling into common code")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Richard Zhu <hongxing.zhu@nxp.com>
Cc: <stable@vger.kernel.org>
-----BEGIN PGP SIGNATURE-----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=RKW4
-----END PGP SIGNATURE-----
Merge tag 'bitmap-5.17-rc1' of git://github.com/norov/linux
Pull bitmap updates from Yury Norov:
- introduce for_each_set_bitrange()
- use find_first_*_bit() instead of find_next_*_bit() where possible
- unify for_each_bit() macros
* tag 'bitmap-5.17-rc1' of git://github.com/norov/linux:
vsprintf: rework bitmap_list_string
lib: bitmap: add performance test for bitmap_print_to_pagebuf
bitmap: unify find_bit operations
mm/percpu: micro-optimize pcpu_is_populated()
Replace for_each_*_bit_from() with for_each_*_bit() where appropriate
find: micro-optimize for_each_{set,clear}_bit()
include/linux: move for_each_bit() macros from bitops.h to find.h
cpumask: replace cpumask_next_* with cpumask_first_* where appropriate
tools: sync tools/bitmap with mother linux
all: replace find_next{,_zero}_bit with find_first{,_zero}_bit where appropriate
cpumask: use find_first_and_bit()
lib: add find_first_and_bit()
arch: remove GENERIC_FIND_FIRST_BIT entirely
include: move find.h from asm_generic to linux
bitops: move find_bit_*_le functions from le.h to find.h
bitops: protect find_first_{,zero}_bit properly
-----BEGIN PGP SIGNATURE-----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=Vgg4
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use pci_find_vsec_capability() instead of open-coding it (Andy
Shevchenko)
- Convert pci_dev_present() stub from macro to static inline to avoid
'unused variable' errors (Hans de Goede)
- Convert sysfs slot attributes from default_attrs to default_groups
(Greg Kroah-Hartman)
- Use DWORD accesses for LTR, L1 SS to avoid BayHub OZ711LV2 erratum
(Rajat Jain)
- Remove unnecessary initialization of static variables (Longji Guo)
Resource management:
- Always write Intel I210 ROM BAR on update to work around device
defect (Bjorn Helgaas)
PCIe native device hotplug:
- Fix pciehp lockdep errors on Thunderbolt undock (Hans de Goede)
- Fix infinite loop in pciehp IRQ handler on power fault (Lukas
Wunner)
Power management:
- Convert amd64-agp, sis-agp, via-agp from legacy PCI power
management to generic power management (Vaibhav Gupta)
IOMMU:
- Add function 1 DMA alias quirk for Marvell 88SE9125 SATA controller
so it can work with an IOMMU (Yifeng Li)
Error handling:
- Add PCI_ERROR_RESPONSE and related definitions for signaling and
checking for transaction errors on PCI (Naveen Naidu)
- Fabricate PCI_ERROR_RESPONSE data (~0) in config read wrappers,
instead of in host controller drivers, when transactions fail on
PCI (Naveen Naidu)
- Use PCI_POSSIBLE_ERROR() to check for possible failure of config
reads (Naveen Naidu)
Peer-to-peer DMA:
- Add Logan Gunthorpe as P2PDMA maintainer (Bjorn Helgaas)
ASPM:
- Calculate link L0s and L1 exit latencies when needed instead of
caching them (Saheed O. Bolarinwa)
- Calculate device L0s and L1 acceptable exit latencies when needed
instead of caching them (Saheed O. Bolarinwa)
- Remove struct aspm_latency since it's no longer needed (Saheed O.
Bolarinwa)
APM X-Gene PCIe controller driver:
- Fix IB window setup, which was broken by the fact that IB resources
are now sorted in address order instead of DT dma-ranges order (Rob
Herring)
Apple PCIe controller driver:
- Enable clock gating to save power (Hector Martin)
- Fix REFCLK1 enable/poll logic (Hector Martin)
Broadcom STB PCIe controller driver:
- Declare bitmap correctly for use by bitmap interfaces (Christophe
JAILLET)
- Clean up computation of legacy and non-legacy MSI bitmasks (Florian
Fainelli)
- Update suspend/resume/remove error handling to warn about errors
and not fail the operation (Jim Quinlan)
- Correct the "pcie" and "msi" interrupt descriptions in DT binding
(Jim Quinlan)
- Add DT bindings for endpoint voltage regulators (Jim Quinlan)
- Split brcm_pcie_setup() into two functions (Jim Quinlan)
- Add mechanism for turning on voltage regulators for connected
devices (Jim Quinlan)
- Turn voltage regulators for connected devices on/off when bus is
added or removed (Jim Quinlan)
- When suspending, don't turn off voltage regulators for wakeup
devices (Jim Quinlan)
Freescale i.MX6 PCIe controller driver:
- Add i.MX8MM support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Use DWC common ops instead of layerscape-specific link-up functions
(Hou Zhiqiang)
Intel VMD host bridge driver:
- Honor platform ACPI _OSC feature negotiation for Root Ports below
VMD (Kai-Heng Feng)
- Add support for Raptor Lake SKUs (Karthik L Gopalakrishnan)
- Reset everything below VMD before enumerating to work around
failure to enumerate NVMe devices when guest OS reboots (Nirmal
Patel)
Bridge emulation (used by Marvell Aardvark and MVEBU):
- Make emulated ROM BAR read-only by default (Pali Rohár)
- Make some emulated legacy PCI bits read-only for PCIe devices (Pali
Rohár)
- Update reserved bits in emulated PCIe Capability (Pali Rohár)
- Allow drivers to emulate different PCIe Capability versions (Pali
Rohár)
- Set emulated Capabilities List bit for all PCIe devices, since they
must have at least a PCIe Capability (Pali Rohár)
Marvell Aardvark PCIe controller driver:
- Add bridge emulation definitions for PCIe DEVCAP2, DEVCTL2,
DEVSTA2, LNKCAP2, LNKCTL2, LNKSTA2, SLTCAP2, SLTCTL2, SLTSTA2 (Pali
Rohár)
- Add aardvark support for DEVCAP2, DEVCTL2, LNKCAP2 and LNKCTL2
registers (Pali Rohár)
- Clear all MSIs at setup to avoid spurious interrupts (Pali Rohár)
- Disable bus mastering when unbinding host controller driver (Pali
Rohár)
- Mask all interrupts when unbinding host controller driver (Pali
Rohár)
- Fix memory leak in host controller unbind (Pali Rohár)
- Assert PERST# when unbinding host controller driver (Pali Rohár)
- Disable link training when unbinding host controller driver (Pali
Rohár)
- Disable common PHY when unbinding host controller driver (Pali
Rohár)
- Fix resource type checking to check only IORESOURCE_MEM, not
IORESOURCE_MEM_64, which is a flavor of IORESOURCE_MEM (Pali Rohár)
Marvell MVEBU PCIe controller driver:
- Implement pci_remap_iospace() for ARM so mvebu can use
devm_pci_remap_iospace() instead of the previous ARM-specific
pci_ioremap_io() interface (Pali Rohár)
- Use the standard pci_host_probe() instead of the device-specific
mvebu_pci_host_probe() (Pali Rohár)
- Replace all uses of ARM-specific pci_ioremap_io() with the ARM
implementation of the standard pci_remap_iospace() interface and
remove pci_ioremap_io() (Pali Rohár)
- Skip initializing invalid Root Ports (Pali Rohár)
- Check for errors from pci_bridge_emul_init() (Pali Rohár)
- Ignore any bridges at non-zero function numbers (Pali Rohár)
- Return ~0 data for invalid config read size (Pali Rohár)
- Disallow mapping interrupts on emulated bridges (Pali Rohár)
- Clear Root Port Memory & I/O Space Enable and Bus Master Enable at
initialization (Pali Rohár)
- Make type bits in Root Port I/O Base register read-only (Pali
Rohár)
- Disable Root Port windows when base/limit set to invalid values
(Pali Rohár)
- Set controller to Root Complex mode (Pali Rohár)
- Set Root Port Class Code to PCI Bridge (Pali Rohár)
- Update emulated Root Port secondary bus numbers to better reflect
the actual topology (Pali Rohár)
- Add PCI_BRIDGE_CTL_BUS_RESET support to emulated Root Ports so
pci_reset_secondary_bus() can reset connected devices (Pali Rohár)
- Add PCI_EXP_DEVCTL Error Reporting Enable support to emulated Root
Ports (Pali Rohár)
- Add PCI_EXP_RTSTA PME Status bit support to emulated Root Ports
(Pali Rohár)
- Add DEVCAP2, DEVCTL2 and LNKCTL2 support to emulated Root Ports on
Armada XP and newer devices (Pali Rohár)
- Export mvebu-mbus.c symbols to allow pci-mvebu.c to be a module
(Pali Rohár)
- Add support for compiling as a module (Pali Rohár)
MediaTek PCIe controller driver:
- Assert PERST# for 100ms to allow power and clock to stabilize
(qizhong cheng)
MediaTek PCIe Gen3 controller driver:
- Disable Mediatek DVFSRC voltage request since lack of DVFSRC to
respond to the request causes failure to exit L1 PM Substate
(Jianjun Wang)
MediaTek MT7621 PCIe controller driver:
- Declare mt7621_pci_ops static (Sergio Paracuellos)
- Give pcibios_root_bridge_prepare() access to host bridge windows
(Sergio Paracuellos)
- Move MIPS I/O coherency unit setup from driver to
pcibios_root_bridge_prepare() (Sergio Paracuellos)
- Add missing MODULE_LICENSE() (Sergio Paracuellos)
- Allow COMPILE_TEST for all arches (Sergio Paracuellos)
Microsoft Hyper-V host bridge driver:
- Add hv-internal interfaces to encapsulate arch IRQ dependencies
(Sunil Muthuswamy)
- Add arm64 Hyper-V vPCI support (Sunil Muthuswamy)
Qualcomm PCIe controller driver:
- Undo PM setup in qcom_pcie_probe() error handling path (Christophe
JAILLET)
- Use __be16 type to store return value from cpu_to_be16()
(Manivannan Sadhasivam)
- Constify static dw_pcie_ep_ops (Rikard Falkeborn)
Renesas R-Car PCIe controller driver:
- Fix aarch32 abort handler so it doesn't check the wrong bus clock
before accessing the host controller (Marek Vasut)
TI Keystone PCIe controller driver:
- Add register offset for ti,syscon-pcie-id and ti,syscon-pcie-mode
DT properties (Kishon Vijay Abraham I)
MicroSemi Switchtec management driver:
- Add Gen4 automotive device IDs (Kelvin Cao)
- Declare state_names[] as static so it's not allocated and
initialized for every call (Kelvin Cao)
Host controller driver cleanups:
- Use of_device_get_match_data(), not of_match_device(), when we only
need the device data in altera, artpec6, cadence, designware-plat,
dra7xx, keystone, kirin (Fan Fei)
- Drop pointless of_device_get_match_data() cast in j721e (Bjorn
Helgaas)
- Drop redundant struct device * from j721e since struct cdns_pcie
already has one (Bjorn Helgaas)
- Rename driver structs to *_pcie in intel-gw, iproc, ls-gen4,
mediatek-gen3, microchip, mt7621, rcar-gen2, tegra194, uniphier,
xgene, xilinx, xilinx-cpm for consistency across drivers (Fan Fei)
- Fix invalid address space conversions in hisi, spear13xx (Bjorn
Helgaas)
Miscellaneous:
- Sort Intel Device IDs by value (Andy Shevchenko)
- Change Capability offsets to hex to match spec (Baruch Siach)
- Correct misspellings (Krzysztof Wilczyński)
- Terminate statement with semicolon in pci_endpoint_test.c (Ming
Wang)"
* tag 'pci-v5.17-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (151 commits)
PCI: mt7621: Allow COMPILE_TEST for all arches
PCI: mt7621: Add missing MODULE_LICENSE()
PCI: mt7621: Move MIPS setup to pcibios_root_bridge_prepare()
PCI: Let pcibios_root_bridge_prepare() access bridge->windows
PCI: mt7621: Declare mt7621_pci_ops static
PCI: brcmstb: Do not turn off WOL regulators on suspend
PCI: brcmstb: Add control of subdevice voltage regulators
PCI: brcmstb: Add mechanism to turn on subdev regulators
PCI: brcmstb: Split brcm_pcie_setup() into two funcs
dt-bindings: PCI: Add bindings for Brcmstb EP voltage regulators
dt-bindings: PCI: Correct brcmstb interrupts, interrupt-map.
PCI: brcmstb: Fix function return value handling
PCI: brcmstb: Do not use __GENMASK
PCI: brcmstb: Declare 'used' as bitmap, not unsigned long
PCI: hv: Add arm64 Hyper-V vPCI support
PCI: hv: Make the code arch neutral by adding arch specific interfaces
PCI: pciehp: Use down_read/write_nested(reset_lock) to fix lockdep errors
x86/PCI: Remove initialization of static variables to false
PCI: Use DWORD accesses for LTR, L1 SS to avoid erratum
misc: pci_endpoint_test: Terminate statement with semicolon
...
