Add GPIO support to the simple helpers for the I2C OF component prober.
Components that the prober intends to probe likely require their
regulator supplies be enabled, and GPIOs be toggled to enable them or
bring them out of reset before they will respond to probe attempts.
Regulator supplies were handled in the previous patch.
The assumption is that the same class of components to be probed are
always connected in the same fashion with the same regulator supply
and GPIO. The names may vary due to binding differences, but the
physical layout does not change.
This supports at most one GPIO pin. The user must specify the GPIO name,
the polarity, and the amount of time to wait after the GPIO is toggled.
Devices with more than one GPIO pin likely require specific power
sequencing beyond what generic code can easily support.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Andrey Skvortsov <andrej.skvortzov@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Add helpers to do regulator management for the I2C OF component prober.
Components that the prober intends to probe likely require their
regulator supplies be enabled, and GPIOs be toggled to enable them or
bring them out of reset before they will respond to probe attempts.
GPIOs will be handled in the next patch.
The assumption is that the same class of components to be probed are
always connected in the same fashion with the same regulator supply
and GPIO. The names may vary due to binding differences, but the
physical layout does not change.
This set of helpers supports at most one regulator supply. The user
must specify the node from which the supply is retrieved. The supply
name and the amount of time to wait after the supply is enabled are
also given by the user.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Some devices are designed and manufactured with some components having
multiple drop-in replacement options. These components are often
connected to the mainboard via ribbon cables, having the same signals
and pin assignments across all options. These may include the display
panel and touchscreen on laptops and tablets, and the trackpad on
laptops. Sometimes which component option is used in a particular device
can be detected by some firmware provided identifier, other times that
information is not available, and the kernel has to try to probe each
device.
This change attempts to make the "probe each device" case cleaner. The
current approach is to have all options added and enabled in the device
tree. The kernel would then bind each device and run each driver's probe
function. This works, but has been broken before due to the introduction
of asynchronous probing, causing multiple instances requesting "shared"
resources, such as pinmuxes, GPIO pins, interrupt lines, at the same
time, with only one instance succeeding. Work arounds for these include
moving the pinmux to the parent I2C controller, using GPIO hogs or
pinmux settings to keep the GPIO pins in some fixed configuration, and
requesting the interrupt line very late. Such configurations can be seen
on the MT8183 Krane Chromebook tablets, and the Qualcomm sc8280xp-based
Lenovo Thinkpad 13S.
Instead of this delicate dance between drivers and device tree quirks,
this change introduces a simple I2C component probe function. For a
given class of devices on the same I2C bus, it will go through all of
them, doing a simple I2C read transfer and see which one of them responds.
It will then enable the device that responds.
This requires some minor modifications in the existing device tree. The
status for all the device nodes for the component options must be set
to "fail-needs-probe". This makes it clear that some mechanism is
needed to enable one of them, and also prevents the prober and device
drivers running at the same time.
Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
