Commit 8d7ae22ae9 ("net: dsa: microchip: KSZ9477 register regmap
alignment to 32 bit boundaries") fixed an issue whereby regmap_reg_range
did not allow writes as 32 bit words to KSZ9477 PHY registers, this fix
for KSZ9896 is adapted from there as the same errata is present in
KSZ9896C as "Module 5: Certain PHY registers must be written as pairs
instead of singly" the explanation below is likewise taken from this
commit.
The commit provided code
to apply "Module 6: Certain PHY registers must be written as pairs instead
of singly" errata for KSZ9477 as this chip for certain PHY registers
(0xN120 to 0xN13F, N=1,2,3,4,5) must be accessed as 32 bit words instead
of 16 or 8 bit access.
Otherwise, adjacent registers (no matter if reserved or not) are
overwritten with 0x0.
Without this patch some registers (e.g. 0x113c or 0x1134) required for 32
bit access are out of valid regmap ranges.
As a result, following error is observed and KSZ9896 is not properly
configured:
ksz-switch spi1.0: can't rmw 32bit reg 0x113c: -EIO
ksz-switch spi1.0: can't rmw 32bit reg 0x1134: -EIO
ksz-switch spi1.0 lan1 (uninitialized): failed to connect to PHY: -EIO
ksz-switch spi1.0 lan1 (uninitialized): error -5 setting up PHY for tree 0, switch 0, port 0
The solution is to modify regmap_reg_range to allow accesses with 4 bytes
boundaries.
Fixes: 5c844d57aa ("net: dsa: microchip: fix writes to phy registers >= 0x10")
Signed-off-by: Jesse Van Gavere <jesse.vangavere@scioteq.com>
Link: https://patch.msgid.link/20241211092932.26881-1-jesse.vangavere@scioteq.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
LAN9646 switch is a 6-port switch with functions like KSZ9897. It has
4 internal PHYs and 1 SGMII port. The chip id read from hardware is
same as KSZ9477, so software driver needs to create a new chip id and
group allowable functions under its chip data structure to
differentiate the product.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://patch.msgid.link/20241109015705.82685-3-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce ksz_parse_dt_phy_config() to validate and parse PHY
configuration from the device tree for KSZ switches. This function
ensures proper setup of internal PHYs by checking `phy-handle`
properties, verifying expected PHY IDs, and handling parent node
mismatches. Sets the PHY mask on the MII bus if validation is
successful. Returns -EINVAL on configuration errors.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241106075942.1636998-7-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement side MDIO channel support for LAN937x switches, providing an
alternative to SPI for PHY management alongside existing SPI-based
switch configuration. This is needed to reduce SPI load, as SPI can be
relatively expensive for small packets compared to MDIO support.
Also, implemented static mappings for PHY addresses for various LAN937x
models to support different internal PHY configurations. Since the PHY
address mappings are not equal to the port indexes, this patch also
provides PHY address calculation based on hardware strapping
configuration.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Replace repeated cleanup code with a single error path using a label.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add support for accessing PHYs via a side MDIO interface in LAN937x
switches. The existing code already supports accessing PHYs via main
management interfaces, which can be SPI, I2C, or MDIO, depending on the
chip variant. This patch enables using a side MDIO bus, where SPI is
used for the main switch configuration and MDIO for managing the
integrated PHYs. On LAN937x, this is optional, allowing them to operate
in both configurations: SPI only, or SPI + MDIO. Typically, the SPI
interface is used for switch configuration, while MDIO handles PHY
management.
Additionally, update interrupt controller code to support non-linear
port to PHY address mapping, enabling correct interrupt handling for
configurations where PHY addresses do not directly correspond to port
indexes. This change ensures that the interrupt mechanism properly
aligns with the new, flexible PHY address mappings introduced by side
MDIO support.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241106075942.1636998-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
These are the preferred way to copy ethtool strings.
Avoids incrementing pointers all over the place.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
(for hellcreek driver)
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Link: https://patch.msgid.link/20241028044828.1639668-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The well-known errata regarding EEE not being functional on various KSZ
switches has been refactored a few times. Recently the refactoring has
excluded several switches that the errata should also apply to.
Disable EEE for additional switches with this errata and provide
additional comments referring to the public errata document.
The original workaround for the errata was applied with a register
write to manually disable the EEE feature in MMD 7:60 which was being
applied for KSZ9477/KSZ9897/KSZ9567 switch ID's.
Then came commit 26dd2974c5 ("net: phy: micrel: Move KSZ9477 errata
fixes to PHY driver") and commit 6068e6d7ba ("net: dsa: microchip:
remove KSZ9477 PHY errata handling") which moved the errata from the
switch driver to the PHY driver but only for PHY_ID_KSZ9477 (PHY ID)
however that PHY code was dead code because an entry was never added
for PHY_ID_KSZ9477 via MODULE_DEVICE_TABLE.
This was apparently realized much later and commit 54a4e5c163 ("net:
phy: micrel: add Microchip KSZ 9477 to the device table") added the
PHY_ID_KSZ9477 to the PHY driver but as the errata was only being
applied to PHY_ID_KSZ9477 it's not completely clear what switches
that relates to.
Later commit 6149db4997 ("net: phy: micrel: fix KSZ9477 PHY issues
after suspend/resume") breaks this again for all but KSZ9897 by only
applying the errata for that PHY ID.
Following that this was affected with commit 08c6d8bae48c("net: phy:
Provide Module 4 KSZ9477 errata (DS80000754C)") which removes
the blatant register write to MMD 7:60 and replaces it by
setting phydev->eee_broken_modes = -1 so that the generic phy-c45 code
disables EEE but this is only done for the KSZ9477_CHIP_ID (Switch ID).
Lastly commit 0411f73c13 ("net: dsa: microchip: disable EEE for
KSZ8567/KSZ9567/KSZ9896/KSZ9897.") adds some additional switches
that were missing to the errata due to the previous changes.
This commit adds an additional set of switches.
Fixes: 0411f73c13 ("net: dsa: microchip: disable EEE for KSZ8567/KSZ9567/KSZ9896/KSZ9897.")
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://patch.msgid.link/20241018160658.781564-1-tharvey@gateworks.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Replace ksz8830 with ksz88x3 for CHIP_ID definition and other
strings. This due to KSZ8830 not being an actual switch but the Chip
ID shared among KSZ8863/8873 switches, impossible to differentiate
from their Chip ID or Revision ID registers.
Now all KSZ*_CHIP_ID macros refer to actual, existing switches which
removes confusion.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoids the need for manual cleanup of_node_put() in early exits
from the loop by using for_each_available_child_of_node_scoped().
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Jinjie Ruan <ruanjinjie@huawei.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
KSZ8895/KSZ8864 is a switch family between KSZ8863/73 and KSZ8795, so it
shares some registers and functions in those switches already
implemented in the KSZ DSA driver.
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Tested-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The KSZ87xx switches have 32 static MAC address table entries and not
8. This fixes -ENOSPC non-critical errors from ksz8_add_sta_mac when
configured as a bridge.
Add a new ksz87xx_dev_ops structure to be able to use the
ksz_r_mib_stat64 pointer for this family; this corrects a wrong
mib->counters cast to ksz88xx_stats_raw. This fixes iproute2
statistics. Rename ksz8_dev_ops structure to ksz88x3_dev_ops, in line
with ksz_is_* naming conventions from ksz_common.h.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-6-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add WoL support for KSZ87xx family of switches. This code was tested
with a KSZ8794 chip.
Implement ksz_common usage of the new device-tree property
'microchip,pme-active-high'.
Make use of the now generalized ksz_common WoL functions, adding an
additional interrupt register write for KSZ87xx. Add helper functions
to convert from PME (port) read/writes to indirect register
read/writes in the dedicated ksz8795 sources. Add initial
configuration during (port) setup as per KSZ9477.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-5-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Generalize KSZ9477 WoL functions at ksz_common. Move dedicated registers
and generic masks to existing structures & defines for that purpose.
Introduction of PME (port) read/write helper functions, which happen
to be the generic read/write for KSZ9477 but not for the incoming
KSZ87xx patch.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-4-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Move KSZ9477 WoL functions to ksz_common, in preparation for adding
KSZ87xx family support.
Signed-off-by: Pieter Van Trappen <pieter.van.trappen@cern.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://patch.msgid.link/20240813142750.772781-3-vtpieter@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The wol variable in ksz_port_set_mac_address() is declared with random
data, but the code in ksz_get_wol call may not be executed so the
WAKE_MAGIC check may be invalid resulting in an error message when
setting a MAC address after starting the DSA driver.
Fixes: 3b454b6390 ("net: dsa: microchip: ksz9477: Add Wake on Magic Packet support")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://patch.msgid.link/20240805235200.24982-1-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver do not support in-band mode and in case of CPU<->Switch
link, this mode is not working any way. So, disable it otherwise ingress
path of the switch MAC will stay disabled.
Note: lan9372 manual do not document 0xN301 BIT(2) for the RGMII mode
and recommend[1] to disable in-band link status update for the RGMII RX
path by clearing 0xN302 BIT(0). But, 0xN301 BIT(2) seems to work too, so
keep it unified with other KSZ switches.
[1] https://microchip.my.site.com/s/article/LAN937X-The-required-configuration-for-the-external-MAC-port-to-operate-at-RGMII-to-RGMII-1Gbps-link-speed
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cross-merge networking fixes after downstream PR.
No conflicts.
Adjacent changes:
e3f02f32a0 ("ionic: fix kernel panic due to multi-buffer handling")
d9c0420999 ("ionic: Mark error paths in the data path as unlikely")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The switch global port interrupt mask, REG_SW_PORT_INT_MASK__4, is
defined as 0x001C in ksz9477_reg.h. The designers used 32-bit value in
anticipation for increase of port count in future product but currently
the maximum port count is 7 and the effective value is 0x7F in register
0x001F. Each port has its own interrupt mask and is defined as 0x#01F.
It uses only 4 bits for different interrupts.
The developer who implemented the current interrupt mechanism in the
switch driver noticed there are similarities between the mechanism to
mask port interrupts in global interrupt and individual interrupts in
each port and so used the same code to handle these interrupts. He
updated the code to use the new macro REG_SW_PORT_INT_MASK__1 which is
defined as 0x1F in ksz_common.h but he forgot to update the 32-bit write
to 8-bit as now the mask registers are 0x1F and 0x#01F.
In addition all KSZ switches other than the KSZ9897/KSZ9893 and LAN937X
families use only 8-bit access and so this common code will eventually
be changed to accommodate them.
Fixes: e1add7dd61 ("net: dsa: microchip: use common irq routines for girq and pirq")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Link: https://lore.kernel.org/r/1719009262-2948-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The errata DS80000754 recommends monitoring potential faults in
half-duplex mode for the KSZ9477 family.
half-duplex is not very common so I just added a critical message
when the fault conditions are detected. The switch can be expected
to be unable to communicate anymore in these states and a software
reset of the switch would be required which I did not implement.
Fixes: b987e98e50 ("dsa: add DSA switch driver for Microchip KSZ9477")
Signed-off-by: Enguerrand de Ribaucourt <enguerrand.de-ribaucourt@savoirfairelinux.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The KSZ9477 allows HSR in-HW offloading for any of two selected ports.
This patch adds check if one tries to use more than two ports with
HSR offloading enabled.
The problem is with RedBox configuration (HSR-SAN) - when configuring:
ip link add name hsr0 type hsr slave1 lan1 slave2 lan2 interlink lan3 \
supervision 45 version 1
The lan1 (port0) and lan2 (port1) are correctly configured as ports, which
can use HSR offloading on ksz9477.
However, when we do already have two bits set in hsr_ports, we need to
return (-ENOTSUPP), so the interlink port (lan3) would be used with
SW based HSR RedBox support.
Otherwise, I do see some strange network behavior, as some HSR frames are
visible on non-HSR network and vice versa.
This causes the switch connected to interlink port (lan3) to drop frames
and no communication is possible.
Moreover, conceptually - the interlink (i.e. HSR-SAN port - lan3/port2)
shall be only supported in software as it is also possible to use ksz9477
with only SW based HSR (i.e. port0/1 -> hsr0 with offloading, port2 ->
HSR-SAN/interlink, port4/5 -> hsr1 with SW based HSR).
Fixes: 5055cccfc2 ("net: hsr: Provide RedBox support (HSR-SAN)")
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver should return RMII interface when XMII is running in RMII mode.
Fixes: 0ab7f6bf16 ("net: dsa: microchip: ksz9477: use common xmii function")
Signed-off-by: Tristram Ha <tristram.ha@microchip.com>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Acked-by: Jerry Ray <jerry.ray@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/1716932066-3342-1-git-send-email-Tristram.Ha@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
IPV is added and used term in 802.1Qci PSFP and merged into 802.1Q (from
802.1Q-2018) for another functions.
Even it does similar operation holding temporal priority value
internally (as it is named), because KSZ datasheet doesn't use the term
of IPV (Internal Priority Value) and avoiding any confusion later when
PSFP is in the Linux world, it is better to rename IPV to IPM (Internal
Priority Mapping).
In addition, LAN937x documentation already use IPV for 802.1Qci PSFP
related functionality.
Suggested-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Woojung Huh <woojung.huh@microchip.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20240510053828.2412516-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Microchip KSZ and LAN variants do not have per port DSCP priority
configuration. Instead there is a global DSCP mapping table.
This patch provides write access to this global DSCP map. In case entry
is "deleted", we map corresponding DSCP entry to a best effort prio,
which is expected to be the default priority for all untagged traffic.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Init priority to queue mapping in the way as it shown in IEEE 802.1Q
mapping example.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I tested ETS support on KSZ9893, so it should work other KSZ989X
variants too, which was till not listed as support.
With this change we now officially not support only ksz8 family of
chips.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add DCB support to configure app trust sources and default port priority.
Following commands can be used for testing:
dcb apptrust set dev lan1 order pcp dscp
dcb app replace dev lan1 default-prio 3
Since it is not possible to configure DSCP-Prio mapping per port, this
patch provide only ability to read switch global dscp-prio mapping and
way to enable/disable app trust for DSCP.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most of Microchip KSZ switches use Internal Priority Value associated
with every frame. For example, it is possible to map any VLAN PCP or
DSCP value to IPV and at the end, map IPV to a queue.
Since amount of IPVs is not equal to amount of queues, add this
information and make use of it in some functions.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert ksz_common to provide its own phylink MAC operations, thus
avoiding the shim layer in DSA's port.c
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7H-009gpq-IF@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The phylink_mac_config function pointer member of struct ksz_dev_ops is
never initialised, so let's remove it to simplify the code.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/E1s0O7C-009gpk-Dh@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This driver has two separate reset sequence in different places:
- gpio/HW reset on start of ksz_switch_register()
- SW reset on start of ksz_setup()
The second one will overwrite drive strength configuration made in the
ksz_switch_register().
To fix it, move ksz_parse_drive_strength() from ksz_switch_register() to
ksz_setup().
Fixes: d67d7247f6 ("net: dsa: microchip: Add drive strength configuration")
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20240304135612.814404-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Implement bridge port isolation for KSZ switches. Enabling the isolation
of switch ports from each other while maintaining connectivity with the
CPU and other forwarding ports. For instance, to isolate swp1 and swp2
from each other, use the following commands:
- bridge link set dev swp1 isolated on
- bridge link set dev swp2 isolated on
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit introduces support for the KSZ8567, a robust 7-port
Ethernet switch. The KSZ8567 features two RGMII/MII/RMII interfaces,
each capable of gigabit speeds, complemented by five 10/100 Mbps
MAC/PHYs.
Signed-off-by: Philippe Schenker <philippe.schenker@impulsing.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Link: https://lore.kernel.org/r/20240130083419.135763-2-dev@pschenker.ch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
In order to pass EEE link modes beyond bit 32 to userspace we have to
complement the 32 bit bitmaps in struct ethtool_eee with linkmode
bitmaps. Therefore, similar to ethtool_link_settings and
ethtool_link_ksettings, add a struct ethtool_keee. In a first step
it's an identical copy of ethtool_eee. This patch simply does a
s/ethtool_eee/ethtool_keee/g for all users.
No functional change intended.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Correct the use of define DSA_TAG_PROTO_LAN937X_VALUE to
DSA_TAG_PROTO_LAN937X to improve readability.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Arun Ramadoss <arun.ramadoss@microchip.com>
Link: https://lore.kernel.org/r/20231206160124.1935451-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Provide a list of valid protocols for which the driver will provide
it's deferred xmit handler.
When using DSA_TAG_PROTO_KSZ8795 protocol, it does not provide a
"connect" method, therefor ksz_connect() is not allocating ksz_tagger_data.
This avoids the following null pointer dereference:
ksz_connect_tag_protocol from dsa_register_switch+0x9ac/0xee0
dsa_register_switch from ksz_switch_register+0x65c/0x828
ksz_switch_register from ksz_spi_probe+0x11c/0x168
ksz_spi_probe from spi_probe+0x84/0xa8
spi_probe from really_probe+0xc8/0x2d8
Fixes: ab32f56a41 ("net: dsa: microchip: ptp: add packet transmission timestamping")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231206071655.1626479-1-sean@geanix.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The ksz driver has bits and pieces of platform_data probing support, but
it doesn't work.
The conventional thing to do is to have an encapsulating structure for
struct dsa_chip_data that gets put into dev->platform_data. This driver
expects a struct ksz_platform_data, but that doesn't contain a struct
dsa_chip_data as first element, which will obviously not work with
dsa_switch_probe() -> dsa_switch_parse().
Pointing dev->platform_data to a struct dsa_chip_data directly is in
principle possible, but that doesn't work either. The driver has
ksz_switch_detect() to read the device ID from hardware, followed by
ksz_check_device_id() to compare it against a predetermined expected
value. This protects against early errors in the SPI/I2C communication.
With platform_data, the mechanism in ksz_check_device_id() doesn't work
and even leads to NULL pointer dereferences, since of_device_get_match_data()
doesn't work in that probe path.
So obviously, the platform_data support is actually missing, and the
existing handling of struct ksz_platform_data is bogus. Complete the
support by adding a struct dsa_chip_data as first element, and fixing up
ksz_check_device_id() to pick up the platform_data instead of the
unavailable of_device_get_match_data().
The early dev->chip_id assignment from ksz_switch_register() is also
bogus, because ksz_switch_detect() sets it to an initial value. So
remove it.
Also, ksz_platform_data :: enabled_ports isn't used anywhere, delete it.
Link: https://lore.kernel.org/netdev/20231204154315.3906267-1-dd@embedd.com/
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Daniel Danzberger <dd@embedd.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Last part of the driver do now support phylink_mac_link_up(). So, make it
not optional.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This patch introduces the function 'ksz8_phy_port_link_up' to the
Microchip KSZ8xxx driver. This function is responsible for setting up
flow control and duplex settings for the ports that are integrated with
PHYs.
The KSZ8795 switch supports asymmetric pause control, which can't be
fully utilized since a single bit controls both RX and TX pause. Despite
this, the flow control can be adjusted based on the auto-negotiation
process, taking into account the capabilities of both link partners.
On the other hand, the KSZ8873's PORT_FORCE_FLOW_CTRL bit can be set by
the hardware bootstrap, which ignores the auto-negotiation result.
Therefore, even in auto-negotiation mode, we need to ensure that this
bit is correctly set.
When auto-negotiation isn't in use, we enforce symmetric pause control
for the KSZ8795 switch.
Please note, forcing flow control disable on a port while still
advertising pause support isn't possible. While this scenario
might not be practical or desired, it's important to be aware of this
limitation when working with the KSZ8873 and similar devices.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-3-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow flow control, speed, and duplex settings on the CPU port to be
configurable. Previously, the speed and duplex relied on default switch
values, which limited flexibility. Additionally, flow control was
hardcoded and only functional in duplex mode. This update enhances the
configurability of these parameters.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/20231127145101.3039399-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ensures a stable PME (Power Management Event) pin state by disabling PME
on system start and enabling it on shutdown only if WoL (Wake-on-LAN) is
configured. This is needed to avoid issues with some PMICs (Power
Management ICs).
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231026051051.2316937-6-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Centralize the switch shutdown routine in a dedicated function,
ksz_switch_shutdown(), to enhance code maintainability and reduce
redundancy. This change abstracts the common shutdown operations
previously duplicated in ksz9477_i2c_shutdown() and ksz_spi_shutdown().
This refactoring is a preparatory step for an upcoming patch to avoid
reset on shutdown if Wake-on-LAN (WoL) is enabled.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231026051051.2316937-5-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Enhance the ksz_switch_macaddr_get() function to handle errors that may
occur during the call to ksz_write8(). Specifically, this update checks
the return value of ksz_write8(), which may fail if regmap ranges
validation is not passed and returns the error code.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231026051051.2316937-4-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Introduce Wake on Magic Packet (WoL) functionality to the ksz9477
driver.
Major changes include:
1. Extending the `ksz9477_handle_wake_reason` function to identify Magic
Packet wake events alongside existing wake reasons.
2. Updating the `ksz9477_get_wol` and `ksz9477_set_wol` functions to
handle WAKE_MAGIC alongside the existing WAKE_PHY option, and to
program the switch's MAC address register accordingly when Magic
Packet wake-up is enabled. This change will prevent WAKE_MAGIC
activation if the related port has a different MAC address compared
to a MAC address already used by HSR or an already active WAKE_MAGIC
on another port.
3. Adding a restriction in `ksz_port_set_mac_address` to prevent MAC
address changes on ports with active Wake on Magic Packet, as the
switch's MAC address register is utilized for this feature.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20231026051051.2316937-2-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
