To prepare the driver for MLO support, split the driver vif data structure to
scale for multiple links. This requires changing the use of arvif to per link
and not per hw which can now comprise of multiple links. Also since most
configurations from mac80211 are done per link, do refactoring of the driver
functions to apply these configurations at link level.
Split ath12k_vif which is the driver private of ieee80211_vif to store link
specific information as ath12k_link_vif. For default use cases the ath12k vif
will have a preallocated link vif called deflink which will be used by non ML
and the first link vif of ML vif.
With MLO support to be added, remaining link vifs will be allocated during
channel assignment where vdev create/start happens. These link vifs will be
freed during interface down.
Current ath12k_vif(arvif) structure
+---------------+ +---------------+ +---------------+
| ieee80211_vif | | ieee80211_vif | | ieee80211_vif |
| private data | | private data | | private data |
| | | | | |
| ath12k_vif | | ath12k_vif | | ath12k_vif |
| (arvif) | | (arvif) | | (arvif) |
| | | | | |
| +----------+ | | +----------+ | | +----------+ |
| |*ar (2GHz)| | | |*ar (5GHz)| | | |*ar (2GHz)| |
| +----------+ | | +----------+ | | +----------+ |
| | | | | |
+---------------+ +---------------+ +---------------+
The new ath12k_vif (ahvif) containing ath12k_link_vif(s) (arvif) (deflink is
preallocated member which is always the first link if ieee80211_vif is MLD and
is the only link otherwise):
+---------------------------------+
| ieee80211_vif |
| private data |
| |
| ath12k_vif(ahvif) |
| |
| +-------------------------------+
| |ath12k_link_vif deflink (arvif)|
| | +---------------+ |
| | | *ar(2GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(5GHz) | |
| +-------------------------------+
| +-------------------------------+
| | ath12k_link_vif *link (arvif)|
| | +---------------+ |
| | | *ar(6GHz) | |
| +-------------------------------+
| |
+---------------------------------+
To refactor existing ath12k_vif to make use of link vifs, following
changes are made:
1. ath12k_vif now called by variable name ahvif storing multiple
arvifs (struct ah12k_link_vif) and also has a back pointer to ieee80211_vif.
2. In this patch set, only deflink is used to be on par with the
existing code. When MLO support is added the link id will be used to fetch
the arvif.
3. For mac80211 ops which doesn't use specific link_id, the config or info
is common for the vif, hence apply the config to all link vifs.
The links_map in the ahvif, will be used to identify all the link vifs that
are setup.
4. Change ath12k_vif_to_arvif() as ath12k_vif_to_ahvif() to fetch the
hw level vif. The link vif can be fetched from ahvif->link[], or the
deflink can be accessed via ahvif->deflink. API to access link
vif (arvif) by passing link_id can be introduced with MLO Support.
5. The ieee80211_vif can be accessed from ahvif using ath12k_ahvif_to_vif().
The locking continues to use wiphy_lock() for protecting access to most data in
struct ath12k&co, there are no changes in that regard. Though struct
ath12k_vif::link[] is protected with RCU.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20241015171416.518022-2-kvalo@kernel.org
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
struct wmi_pdev_bss_chan_info_event is not similar to the firmware
struct definition, this will cause some random failures.
Fix by matching the struct wmi_pdev_bss_chan_info_event with the
firmware structure definition.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240331183232.2158756-3-quic_kathirve@quicinc.com
Currently, the firmware returns incorrect pdev_id information in
WMI_PDEV_BSS_CHAN_INFO_EVENTID, leading to incorrect filling of
the pdev's survey information.
To prevent this issue, when requesting BSS channel information
through WMI_PDEV_BSS_CHAN_INFO_REQUEST_CMDID, firmware expects
pdev_id as one of the arguments in this WMI command.
Add pdev_id to the struct wmi_pdev_bss_chan_info_req_cmd and fill it
during ath12k_wmi_pdev_bss_chan_info_request(). This resolves the
issue of sending the correct pdev_id in WMI_PDEV_BSS_CHAN_INFO_EVENTID.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240331183232.2158756-2-quic_kathirve@quicinc.com
Currently, the Rx data path only supports parsing peer metadata of version
zero. However, the QCN9274 platform configures the peer metadata version
as V1B. When V1B peer metadata is parsed using the version zero logic,
invalid data is populated, causing valid packets to be dropped. To address
this issue, refactor the peer metadata version and add the version based
parsing to populate the data from peer metadata correctly.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Fixes: 2870338109 ("wifi: ath12k: add support for peer meta data version")
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240624145418.2043461-1-quic_periyasa@quicinc.com
With WoWLAN enabled and after sleeping for a rather long time,
we are seeing that with some APs, it is not able to wake up
the STA though the correct wake up pattern has been configured.
This is because the host doesn't send keepalive command to
firmware, thus firmware will not send any packet to the AP and
after a specific time the AP kicks out the STA.
So enable keepalive before going to suspend and disable it after
resume back.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-9-quic_bqiang@quicinc.com
Host sets GTK related info to firmware before WoW is enabled, and
gets rekey replay_count and then disables GTK rekey when WoW quits.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-8-quic_bqiang@quicinc.com
Support ARP and NS offload in WoW state.
Tested this way: put machine A with QCA6390 to WoW state,
ping/ping6 machine A from another machine B, check sniffer to see
any ARP response and Neighbor Advertisement from machine A.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-7-quic_bqiang@quicinc.com
Host needs to set hardware data filter before entering WoW to
let firmware drop needless broadcast/multicast frames to avoid
frequent wakeup. Host clears hardware data filter when leaving WoW.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-6-quic_bqiang@quicinc.com
Implement net-detect feature by setting flag
WIPHY_WOWLAN_NET_DETECT if firmware supports this
feature. Driver sets the related PNO configuration
to firmware before entering WoW and firmware then
scans periodically and wakes up host if a specific
SSID is found.
Note that firmware crashes if we enable it for both
P2P vdev and station vdev simultaneously because
firmware can only support one vdev at a time. Since
there is rare scenario for a P2P vdev to do net-detect,
skip it for P2P vdevs.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-5-quic_bqiang@quicinc.com
Implement basic WoW functionalities such as magic-packet, disconnect
and pattern. The logic is very similar to ath11k.
When WoW is configured, ath12k_core_suspend and ath12k_core_resume
are skipped (by checking ar->state) as we are not allowed to power
cycle firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-4-quic_bqiang@quicinc.com
Implement WoW enable and WoW wakeup commands which are needed
for suspend/resume.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://patch.msgid.link/20240604055407.12506-3-quic_bqiang@quicinc.com
The current value of the MAX_RADIOS definition is 3. This is incorrect
because no device supports more than 2 radios.
An incorrect MAX_RADIOS value can lead to:
- unnecessary memory allocation for pdev related entities.
- invalid pdev id validation.
- Misconceptions for code readers.
Therefore, modify the MAX_RADIOS definition as 2.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240514063412.3483723-3-quic_periyasa@quicinc.com
Add new function ath12k_mac_setup_bcn_tmpl_ema() which retrieves
a list of EMA (Enhanced Multi-BSSID Advertisements) beacon templates
from mac80211 and sends all to firmware. Add support to send EMA
configurations to firmware by adding a new parameter 'ema_params' in
struct wmi_bcn_tmpl_cmd.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-9-quic_alokad@quicinc.com
Include MBSSID parameters in WMI vdev up operation.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-6-quic_alokad@quicinc.com
Host needs to send multiple BSSID configurations to firmware for
each vdev in ath12k_wmi_vdev_up() for AP mode. This function accepts
individual input parameters hence any new argument will require changes
to all callers. Most of these will use default value (0 or NULL).
Create a structure for the function arguments and include objects with
all members initialized to zero to minimize future changes.
Tested-on : QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-5-quic_alokad@quicinc.com
Rename trans_bssid to tx_vdev_bssid to make it similar to vdev_bssid.
Rename profile_num to nontx_profile_cnt, and profile_idx to
nontx_profile_idx which make it clear that these configurations
correspond to nontransmitted MBSSID profiles.
These members are currently unused in the driver.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-4-quic_alokad@quicinc.com
Configure multiple BSSID flags and vdev_id of the transmited profile
in vdev create/start commands depending on the service bit
WMI_TLV_SERVICE_MBSS_PARAM_IN_VDEV_START_SUPPORT.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-3-quic_alokad@quicinc.com
Advertise the driver support for multiple BSSID (MBSSID) and
enhanced multi-BSSID advertisements (EMA) by setting extended
capabilities.
Configure mbssid_max_interfaces and ema_max_profile_periodicity
fields in structure wiphy which are used to advertise maximum number
of interfaces and profile periodicity supported by the driver.
Add new WMI fields to configure maximum vdev count supported for
MBSSID and profile periodicity in case of EMA.
Set WMI_RSRC_CFG_FLAGS2_CALC_NEXT_DTIM_COUNT_SET flag to allow
firmware to track and update the DTIM counts for each nontransmitted
profile.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240508202912.11902-2-quic_alokad@quicinc.com
When AP goes down or too far away without indication to STA, beacon miss
will be detected. Then for WCN7850's firmware, it will use roam event
to send beacon miss to host.
If STA doesn't handle the beacon miss, will keep the fake connection
and unable to roam.
So add support for WCN7850 to trigger disconnection from AP when
receiving this event from firmware.
It has to be noted that beacon miss event notification for QCN9274
to be handled in a separate patch as it uses STA kickout WMI event
to notify beacon miss and the current STA kickout event is processed
as low_ack.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Reviewed-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240412094447.2063-1-quic_kangyang@quicinc.com
Currently, ath12k does not have the ability to set band edge channel power
for WCN7850. In order to support this, ath12k gets band edge channel power
table in ath12k_acpi_dsm_get_data() function and sets pdev_id and
param_type_id, then finally sends these data and
WMI_PDEV_SET_BIOS_INTERFACE_CMDID to firmware to set band edge channel
power.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-5-quic_lingbok@quicinc.com
Currently, ath12k does not have the ability to adjust Clear Channel Assessment
(CCA) threshold values to meet the regulatory requirements. Get the values from
ACPI and send them to the firmware using ath12k_wmi_set_bios_cmd() function.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-4-quic_lingbok@quicinc.com
In order to enable ACPI SAR (Specific Absorption Rate), ath12k gets SAR and GEO
offset tables from ACPI and sends the data to firmware using
WMI_PDEV_SET_BIOS_SAR_TABLE_CMDID and WMI_PDEV_SET_BIOS_GEO_TABLE_CMDID
commands.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-3-quic_lingbok@quicinc.com
Currently, ath12k does not support Time-Average-SAR (TAS). In order to enable
TAS read the tables from ACPI and send them to the firmware using
WMI_PDEV_SET_BIOS_INTERFACE_CMDID command. Besides, ath12k registers an ACPI
event callback so that ACPI can notify ath12k to get the updated SAR power
table and sends it to the firmware when the device state is changed.
ACPI is only enabled for WCN7850 using struct ath12k_hw_params::acpi_guid
field. Most likely QCN9274 will never support ACPI as the chip is not used in
laptops.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240422033054.979-2-quic_lingbok@quicinc.com
The survey dump statistics does not display channel RX and TX time
properly because the survey flag is not enabled in the firmware service
flag.
If firmware supports enable the service flag "bss_chan_info" in
wmi_resource_config to fetch and print the stats for specific pdev.
Enabling WMI_RSRC_CFG_FLAG1_BSS_CHANNEL_INFO_64 does not have any impact
on WCN7850 since this bit is not utilized by the WCN7850 firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Thiraviyam Mariyappan <quic_tmariyap@quicinc.com>
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240410085329.3649572-1-quic_kathirve@quicinc.com
Every time EHT Operation element changed, mac80211 will parse it and
extract the valid puncturing bitmap according to the bandwidth.
Current driver only update puncturing bitmap to firmware as vdev
parameter. Which can only meet the needs of AP. But STA will also use
it as peer parameter. If only update as vdev parameter, might cause
firmware crash. QCN9274 is the same.
So update bandwidth and puncturing bitmap as peer parameters once they
changed for STA. Then send them to the firmware by WMI event.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240408083047.22548-1-quic_kangyang@quicinc.com
The WMI commands are in little endian byte order, fix missing endianness
conversion in wmi_vdev_create_cmd.
Tested-on: WCN7850 hw2.0 WLAN.IOE_HMT.1.0.2-00240-QCAHMTSWPL_V1.0_V2.0_SILICON-1
Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240322003726.2016208-1-quic_miaoqing@quicinc.com
There are some duplicate definitions in wmi.h, remove them.
No functional changes, compile tested only.
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240314021830.305021-1-quic_kangyang@quicinc.com
ath12k inherited struct wmi_start_scan_arg from ath11k. However, in
ath12k, this struct is unused -- struct ath12k_wmi_scan_req_arg is
used for this functionality. So remove the unused struct.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240226-ath12k-obsolete-wmi_start_scan_arg-v1-1-07b0b563cb27@quicinc.com
As done for ath11k, lets keep on cleaning up struct ath12k_wmi_scan_req_arg by
removing the unused scan_events. Also remove the underlying union & struct
construct as it isn't needed anymore. No functionnal changes.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240211151104.1951418-1-nico.escande@gmail.com
As we did for ath11k lets remove the unused scan_flags from struct
ath12k_wmi_scan_req_arg. This will prevent us from using out of sync values
between WMI_SCAN_XXX & scan_f_xxx bitfield.
While at it remove the underlying wrapping struct/union construct as it serves
no purpose anymore.
Signed-off-by: Nicolas Escande <nico.escande@gmail.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240211145548.1939610-3-nico.escande@gmail.com
Mac80211 needs more space for P2P scan ie in P2P mode, 256 is not
enough, resize it to 512.
Also delete the duplicate macro definitions in wmi.h.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-8-quic_kangyang@quicinc.com
The Notice of Absence (NoA) attribute is used by the P2P Group Owner to
signal its absence due to power save timing, concurrent operation, or
off-channel scanning. It is also used in the P2P Presence Request-Response
mechanism.
The NoA attribute shall be present in the P2P IE in the beacon frames
transmitted by a P2P Group Owner when a NoA schedule is being advertised,
or when the CTWindow is non-zero.
So add support to update P2P information after P2P GO is up through
event WMI_P2P_NOA_EVENTID, and always put it in probe resp.
Create p2p.c and p2p.h for P2P related functions and definitions.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-6-quic_kangyang@quicinc.com
P2P Element is a necessary component of P2P protocol communication.
It contains the Vendor Specific Information Element which includes
the WFA OUI and an OUI Type indicating P2P.
Add P2P IE in beacon template, and implement WMI interface for it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-5-quic_kangyang@quicinc.com
Current structure wmi_vdev_create_cmd is not matched to the firmware
definition. So update it.
And update vdev_stats_id_valid for vdev_stats_id.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <quic_kangyang@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240130040303.370590-2-quic_kangyang@quicinc.com
When ath12k send TWT disable command to firmware, firmware will return a
TWT disable event to ath12k. Through the analysis of TWT disable event
status, we can easily obtain the status of TWT disable command. It can be
more convenient to debug TWT.
This patch works with WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240122085336.3985-3-quic_lingbok@quicinc.com
When ath12k send TWT enable command to firmware, firmware will return a TWT
enable event to ath12k. Through the analysis of TWT enable event status, we
can easily obtain the status of TWT enable command. It can be more
convenient to debug TWT.
This patch works with WCN7850 and QCN9274.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240122085336.3985-2-quic_lingbok@quicinc.com
Most of the RX descriptors fields are currently not used in the
ath12k driver. Hence add support to selectively subscribe to the
required quad words (64 bits) within msdu_end and mpdu_start of
rx_desc.
Add compact rx_desc structures and configure the bit mask for Rx TLVs
(msdu_end, mpdu_start, mpdu_end) via registers. With these registers
SW can configure to DMA the partial TLV struct to Rx buffer.
Each TLV type has its own register to configure the mask value.
The mask value configured in register will indicate if a particular
QWORD has to be written to rx buffer or not i.e., if Nth bit is enabled
in the mask Nth QWORD will be written and it will not be written if the
bit is disabled in mask. While 0th bit indicates whether TLV tag will be
written or not.
Advantages of Qword subscription of TLVs
- Avoid multiple cache-line misses as the all the required fields
of the TLV are within 128 bytes.
- Memory optimization as TLVs + DATA + SHINFO can fit in 2k buffer
even for 64 bit kernel.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Karthikeyan Kathirvel <quic_kathirve@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-10-quic_rajkbhag@quicinc.com
Add support to process WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT
service bit. If this service bit is set by firmware, then it expects
host to set rx_peer_meta_data_ver in wmi_resource_config's flags2
with value 3 for QCN9274 to indicate as V1B meta version. If this is
not set firmware crash is seen during peer addition.
Hence, if WMI_TLV_SERVICE_PEER_METADATA_V1A_V1B_SUPPORT service bit
is set by firmware, set correct peer metadata version to avoid
firmware crash.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Harshitha Prem <quic_hprem@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-4-quic_rajkbhag@quicinc.com
Currently while fetching for pdev id from WMI_SERVICE_READY_EXT_EVENTID
we consider 32 bit pdev_id in ath12k_wmi_caps_ext_params structure. But
Firmware sends lower 16 bit for pdev id along with higher 16 bit for
hw_link_id. Due to this wrong pdev id is fetched. This wrong pdev id
when used for WMI commands leads to Firmware crash.
Hence fetch the correct pdev id considering only the lower 16 bits.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Co-developed-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-3-quic_rajkbhag@quicinc.com
When any VDEV is started, MBSSID flags are passed to firmware to
indicate if its a MBSSID/EMA AP vdev. If the interface is not an AP
or if the AP doesn't support MBSSID, the vdev needs to be brought up
as a non MBSSID vdev. Set these flags as a non MBSSID AP by default
which can be updated as and when MBSSID support is added in ath12k.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00188-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://msgid.link/20240129065724.2310207-2-quic_rajkbhag@quicinc.com
Add 320 MHz bandwidth as a new bandwidth enum for ATH12k driver. This
is extending existing bandwidth related enums to include 320 MHz. This
is a precursor to supporting 320 MHz in the future.
Sanity test performed to confirm that there was no impact in existing
bandwidths.
Additionally update QuIC copyright to include 2023 in hal_rx.h.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00125-QCAHKSWPL_SILICONZ-1
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231116221839.1303170-1-quic_msinada@quicinc.com
Currently wmi.h has two separate set of definitions for peer
flags. One set of flags is defined in enum wmi_tlv_peer_flags, and,
except for the last three, are named WMI_TLV_PEER_*. The other set of
flags are defined as macros, and are named WMI_PEER_*. The last three
macros have the same name as the last three wmi_tlv_peer_flags
enumerators.
The code only uses the WMI_PEER_* names; the WMI_TLV_PEER_* names are
unused. So as a first step in consolidation, remove all the
WMI_TLV_PEER_* names.
But since having an enum to define all the flags is actually a good
thing since that provides a handle by which to refer to the entire set
of flags, recast the WMI_PEER_* macros into enumerators.
Compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231106-ath-peer-flags-v1-4-781e83b7e8e8@quicinc.com
Currently both struct ath12k_wmi_pdev and struct ath12k_wmi_base
define:
const struct wmi_peer_flags_map *peer_flags;
But that member is not used, and in fact, struct wmi_peer_flags_map
is not defined within ath12k; these are obsolete remnants inherited
from ath11k. So remove them.
Compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231106-ath-peer-flags-v1-2-781e83b7e8e8@quicinc.com
In a special WCN7855 firmware release the EHT (IEEE 802.11be) support has
been disabled for size reduction. Currently ath12k always enables EHT PHY
mode during vdev start but with the special firmware that will cause a
firmware crash during vdev start in firmware initialisation. This is
because the firmware will use the EHT mode to allocate resources but as
the EHT mode is not available in the firmware, there's an internal
conflict and the firmware will crash.
To fix the crash check the WMI_TLV_SERVICE_11BE flag to see if the firmware
supports EHT. If EHT is not supported downgrade the PHY mode to HE
(IEEE 802.11ax).
This does not impact QCN9274, because WMI_SERVICE_11BE is always enabled
for QCN9274, then eht_cap->has_eht will always set for it, and the logic
of this patch will not take effect and the PHY mode will not down grade
for it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230913105757.17744-1-quic_wgong@quicinc.com
When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
Commit d889913205 ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices")
declared but never implemented these, remove it.
Signed-off-by: Yue Haibing <yuehaibing@huawei.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230816130550.50896-1-yuehaibing@huawei.com
Enable the feature flag to indicate the driver support for
preamble puncturing. Firmware will support this feature
by default from IEEE 802.11be onwards.
Configure the bitmap as part of VDEV start/restart and
peer association commands.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-12-quic_alokad@quicinc.com
Add required peer association definitions and processing if the
bandwidth is 320 MHz.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu<quic_pradeepc@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-9-quic_alokad@quicinc.com
Add new WMI tag and pass the EHT parameters for peer association
to firmware.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230725224034.14045-8-quic_alokad@quicinc.com
