[why]
Rename hw_sequencer to hwseq.
Move all hwseq files to unique
folder hwss.
[how]
creating hwss repo in dc, and moved the dcnxx_hwseq.c
and .h files into corresponding new folders inside the hwss
and cleared the linkage errors by adding relative paths
in the Makefile.template.
Reviewed-by: Martin Leung <martin.leung@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Mounika Adhuri <moadhuri@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
dc->caps.color.mpc.gamut_remap says there is a post-blending color block
for gamut remap matrix for DCN3 HW family and newer versions. However,
those drivers still follow DCN10 programming that remap stream
gamut_remap_matrix to DPP (pre-blending).
To enable pre-blending and post-blending gamut_remap matrix supports at
the same time, set stream gamut_remap to MPC and plane gamut_remap to
DPP for DCN families that support both.
It was tested using IGT KMS color tests for DRM CRTC CTM property and it
preserves test results.
Signed-off-by: Melissa Wen <mwen@igalia.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
OTG_STATIC_SCREEN_EVENT_MASK is changed in DCN3,
but we still follow DCN2 to apply setting for
OTG_STATIC_SCREEN_EVENT_MASK.
[How]
Add new function to apply correct settings for DCN3 series.
Reviewed-by: Anthony Koo <anthony.koo@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: SungHuai Wang <danny.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit e383b12709.
Controling hubp power gating using the DMCUB isn't stable so we
are reverting this change to move control back into the driver.
Cc: stable@vger.kernel.org # 6.3+
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Hamza Mahfooz <hamza.mahfooz@amd.com>
Signed-off-by: Daniel Miess <daniel.miess@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Drop dead code for Linux.
[How]
Remove all IS_FPGA_MAXIMUS_DC and IS_DIAG_DC
Reviewed-by: Ariel Bernstein <eric.bernstein@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Currently, there is an intermittent issue where a screen can either go
blank or be corrupted.
[HOW]
To resolve the issue we trigger the ramping logic for DIO FIFO so that
it goes back up to the correct speed.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Saaem Rizvi <syedsaaem.rizvi@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why && How]
We would like to have visual confirm color support for MCLK switch.
1. Set visual confirm color to yellow: Vblank MCLK switch.
2. Set visual confirm color to cyan: FPO + Vblank MCLK
switch.
3. Set visual confirm color to pink: Vactive MCLK switch.
Reviewed-by: Jun Lei <jun.lei@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
This is originally a change (9c75891f) in DCN32 because of the lack
of interface to set TX while keeping symclk on. Adding this workaround
to DCN314 will resolve the current issue.
Fixes: 9c75891fee ("drm/amd/display: rework recent update PHY state commit")
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Leo Chen <sancchen@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Doing core_link_disable_stream or set_dpms_off when reinitializing
hardware causes issue to repro with external display connected. This is
unnecessary, blanking pixel data should be sufficient.
[How]
Call disable_pixel_data while reinitializing hardware instead of
core_link_disable_stream or set_dpms_off.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Michael Mityushkin <michael.mityushkin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DPP Root clock optimization when combined with 4to1 MPC combine results
in the screen turning black.
This is because the DPPCLK is stopped during the middle of an
optimize_bandwidth sequence during commit_minimal_transition without
going through plane power down/power up.
[How]
The intent of a 0Hz DPP clock through update_clocks is to disable the
DTO. This differs from the behavior of stopping the DPPCLK entirely
(utilizing a 0Hz clock on some ASIC) so it's better to move this logic
to reside next to plane power up/power down where we gate the HUBP/DPP
DOMAIN.
The new sequence should be:
Power down: PG enabled -> RCO on
Power up: RCO off -> PG disabled
Rename power_on_plane to power_on_plane_resources to reflect the
actual operation that's occurring.
Cc: stable@vger.kernel.org
Cc: Mario Limonciello <mario.limonciello@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DOMAIN power gating control is now required to be done via firmware
due to interlock with other power features. This is to avoid
intermittent issues in the LB memories.
[How]
If the firmware supports the command then use the new firmware as
the sequence can avoid potential display corruption issues.
The command will be ignored on firmware that does not support DOMAIN
power control and the pipes will remain always on - frequent PG cycling
can cause the issue to occur on the old sequence, so we should avoid it.
Reviewed-by: Hansen Dsouza <hansen.dsouza@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit c800d9ff8c.
[why]
revert for now because this change exposed other issue.
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
HW register bit define changed.
Reviewed-by: Zhan Liu <Zhan.Liu@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Charlene Liu <Charlene.Liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Original change 594b237b9a ("drm/amd/display: Add
interface to track PHY state") was implemented by assuming stream's
dpms off is equivalent to PHY power off.
This assumption doesn't hold in following situations:
1. MST multiple stream scenario, where multiple streams are sharing the
same PHY output. Toggle dpms off for one of the stream doesn't power
off the PHY due to the presence of other streams.
2. enable stream failure scenario, where enable stream fails due to
failure of link training. This will cause DPMS off is set to false, while
the actual PHY power state is off in certain cases.
Due to the problematic assumption, the logic will skip disabling
other streams for MST multiple stream scenario, therefore PHY is
not actually powered off.
[how]
1. Rework this refactor by moving PHY state update down to hardware
level, where we update PHY state in place when hardware sequencer
is actually changing the power state of the PHY hardware.
2. Reimplement symclk on TX off workaround in place when we are actually
calling transmitter control to power off PHY in dcn32. Note the workaround is
added due to the lack of proper software interface to set TX while keeping
symclk on. We plan to address this interface problem so we can set TX off
only without affecting symclk in future dcn versions.
Fixes: 594b237b9a ("drm/amd/display: Add interface to track PHY state")
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Wenjing Liu <wenjing.liu@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why and How]
- Only consider pixel rate div policy for DCN32+
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Wayne Lin <wayne.lin@amd.com>
Signed-off-by: Alvin Lee <Alvin.Lee2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DIG_FIFO_OUTPUT_PIXEL_MODE not being set for dcn314
resulting in incorrect timing for YCbCr4:2:0
[How]
Copy the implementation of set_pixels_per_cycle from dcn32
over to dcn314
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Tom Chung <chiahsuan.chung@amd.com>
Signed-off-by: Daniel Miess <Daniel.Miess@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY/HOW]
Need to calculate and set some pixel rate divisors on correct otg_inst
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Alex Hung <alex.hung@amd.com>
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Display Core support for DCN 3.1.4
v2:(squash)fix non-x86 in dc/dcn314/Makefile
Properly handle PPC as well. (Alex)
v3: minor cleanup (Alex)
v4: fix comment (Alex)
Signed-off-by: Roman Li <roman.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
