At the moment modesetting pipe C on IVB will fail if pipe B uses 4 FDI
lanes. Make the BW sharing more dynamic by trying to reduce pipe B's
link bpp in this case, until pipe B uses only up to 2 FDI lanes.
For this instead of the encoder compute config retry loop - which
reduced link bpp only for the encoder's pipe - reduce the maximum link
bpp for pipe B/C as required after all CRTC states are computed and
recompute the CRTC states with the new bpp limit.
Atm, all FDI encoder's compute config function returns an error if a BW
constrain prevents increasing the pipe bpp value. The corresponding
crtc_state->bw_constrained check can be replaced with checking
crtc_state->max_link_bpp_x16, add TODO comments for this. SDVO is an
exception where this case is only handled in the outer config retry
loop, failing the modeset with a WARN, add a FIXME comment to handle
this in the encoder code similarly to other encoders.
v2:
- Don't assume that a CRTC is already in the atomic state, while
reducing its link bpp.
- Add DocBook description to intel_fdi_atomic_check_link().
v3:
- Enable BW management for FDI links in a separate patch. (Ville)
v4: (Ville)
- Fail the SDVO encoder config computation if it doesn't support the
link bpp limit.
- Add TODO: comments about checking link_bpp_x16 instead of
bw_constrained.
v5:
- Replace link bpp limit check with a FIXME: comment in
intel_sdvo_compute_config(). (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
[Amended commit message wrt. changes in v5]
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230921195159.2646027-11-imre.deak@intel.com
Each SDVO device can have up to three sets of DDC pins.
Currently we just register a single i2c_adapter for the
entire SDVO device and semi-randomly pick the "correct"
set of DDC pins during intel_sdvo_tmds_sink_detect().
This doesn't make any real sense especially if we have
multiple outputs each with their own dedicated DDC bus.
Let's clean up this mess and register a dedicated
i2c_adapter for each of the possible pin pairs. Each
output (ie. connector) can then pick the correct i2c_adapter
to use for its DDC bus. And we can just switch over to
drm_connector_init_with_ddc() to take care of the
connector->ddc association, which also populates the
"ddc" sysfs symlink as a bonus.
And now that things are based on the actual connector we can
also nuke the sketchy sdvo->controller_output thing.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825134431.24391-6-ville.syrjala@linux.intel.com
We should switch over to the standard "ddc" per-connector
symlink instead of rolling our own thing. The i2c specific
symlink is also in the way of reworking the SDVO DDC handling
(which is a mess atm) so get rid of it.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825134431.24391-5-ville.syrjala@linux.intel.com
Instead of operating on the output the user specified (via the
connector) the current code tends to operate on whichever outputs
it has detected as attached. That is not how the kms uapi is supposed
to work. So simply get rid of attached_outputs and instead directly
operate on the output the user has specified.
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230825134431.24391-2-ville.syrjala@linux.intel.com
port_clock is what the encoder/dpll code is supposed to calculate,
it is not the input clock. Use the dotclock as the target we're
trying to achieve instead.
TODO: the SDVO TV clocking is a mess atm and needs further work
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230705202122.17915-7-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
The SDVO inputs are reported a simple number, not a bitmask.
Adjust the code to match reality.
Note that we don't actually support dual input SDVO devices,
and we just always use the first input.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230705202122.17915-4-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
I have at least one SDVO device (some Lenovo DVI-I ADD2 card,
based on Conexant CX25904) where GetAttachedDisplays returns
success but fails to report any attached displays unless we
precede the command with a SetTargetOutput. Make it so.
I wasn't able to spot anything in the SDVO spec stating that
this should be necessary, but real world wins over spec.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230705202122.17915-2-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Commit 3f9ffce576 ("drm/i915: Do panel VBT init early if the VBT
declares an explicit panel type") started using -1 as the value for
unset panel_type. It gets initialized in intel_panel_init_alloc(), but
the SDVO code never calls it.
Call intel_panel_init_alloc() to initialize the panel, including the
panel_type.
Reported-by: Tomi Leppänen <tomi@tomin.site>
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/8896
Fixes: 3f9ffce576 ("drm/i915: Do panel VBT init early if the VBT declares an explicit panel type")
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # v6.1+
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Tested-by: Tomi Leppänen <tomi@tomin.site>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230803122706.838721-1-jani.nikula@intel.com
The SDVO code already warns when the port in question doesn't
actually support SDVO. Let's make that also bail the encoder
registration like the generic assert_port_valid() we added.
And add a similar thing for g4x HDMI, mainly because on g4x
itsefl port D only supports DP but not SDVO/HDMI. For the
other platforms the generic port_mask check should actually
be sufficient, but since we're here might as well list the
ports.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-6-ville.syrjala@linux.intel.com
Sprinkle some asserts to catch any mishaps in the port_mask
vs. output init.
For DDI/DP/HDMI/SDVO I decided that we want to bail out for
an invalid port since those are the encoder types where
we might want consider driving the whole thing from the VBT
child device list, and bogus VBTs could be a real issue
(if for no other reason than the i915.vbt_firmware).
For DVO and HSW/BDW CRT port I just threw the assert in
there for good measure.
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230616140820.11726-5-ville.syrjala@linux.intel.com
The decision to use DFP output format conversion capabilities should be
during compute_config phase.
This patch adds new member to crtc_state to represent the final
output_format to the sink. In case of a DFP this can be different than
the output_format, as per the format conversion done via the PCON.
This will help to store only the format conversion capabilities of the
DP device in intel_dp->dfp, and use crtc_state to compute and store the
configuration for color/format conversion for a given mode.
v2: modified the new member to crtc_state to represent the final
output_format that eaches the sink, after possible conversion by
PCON kind of devices. (Ville)
v3: Addressed comments from Ville:
-Added comments to clarify difference between sink_format and
output_format.
-Corrected the order of setting sink_format and output_format.
-Added readout for sink_format in get_pipe_config hooks.
v4: Set sink_format for intel_sdvo too. (Ville)
v5: Rebased.
v6: Fixed condition to go for YCbCr420 format for dp and hdmi. (Ville)
v7: Fix the condition to set sink_format for HDMI.
Set hdmi output_format simply as sink_format. (Ville)
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230427125605.487769-2-ankit.k.nautiyal@intel.com
It's a bit confusing to have two cached EDIDs in struct intel_connector
with slightly different purposes. Make the distinction a bit clearer by
moving the EDID cached for eDP and LVDS panels at connector init time to
struct intel_panel, and name it fixed_edid. That's what it is, a fixed
EDID for the panels.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/328350ef918638928a8286cdbab3107c8258332d.1674643465.git.jani.nikula@intel.com
Read out the ELD from the hw so the state checker can verify it.
v2: Check the "ELD valid" bit separately
v3: Fix ELD tx rate handling during readout
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> #v1
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-10-ville.syrjala@linux.intel.com
Align the SDVO audio code with the native HDMI/DP audio and
use just the "presence detect" bit for the has_audio readout.
The "ELD valid" bit will be used for ELD readout soon.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-9-ville.syrjala@linux.intel.com
Use the precomputed crtc_state->eld for audio setup on SDVO
just like we do with native HDMI.
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124144628.4649-8-ville.syrjala@linux.intel.com
Lots of ADL machines out there with bogus VBTs that declare
two eDP child devices. In order for those to work we need to
figure out which power sequencer to use before we try the EDID
read. So let's do the panel VBT init early if we can, falling
back to the post-EDID init otherwise.
The post-EDID init panel_type=0xff approach of assuming the
power sequencer should already be enabled doesn't really work
with multiple eDP panels, and currently we just end up using
the same power sequencer for both eDP ports, which at least
confuses the wakeref tracking, and potentially also causes us
to toggle the VDD for the panel when we should not.
Cc: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221125173156.31689-3-ville.syrjala@linux.intel.com
Turns out many of the files that need i915_reg.h get it implicitly via
{display/intel_de.h, gt/intel_context.h} -> i915_trace.h -> i915_irq.h
-> i915_reg.h. Since i915_trace.h doesn't actually need i915_irq.h,
makes sense to drop it, but that requires adding quite a few new
includes all over the place.
Prefer including i915_reg.h where needed instead of adding another
implicit include, because eventually we'll want to split up i915_reg.h
and only include the specific registers at each place.
Also some places actually needed i915_irq.h too.
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/6e78a2e0ac1bffaf5af3b5ccc21dff05e6518cef.1668008071.git.jani.nikula@intel.com
Avoid having to call the output init function for each
output type separately. We can just call the right one
based on the "class" of the output.
Technically we could just walk the bits of the bitmask
but that could change the order in which we initialize
the outputs. To avoid any behavioural changes keep to
the same explicit probe order as before.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026101134.20865-8-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Get rid of this silly output type<->device index back and
forth and just pass the output type directly to the corresponding
output init function. This was already being done for TV outputs
anyway.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026101134.20865-7-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Stop enumerating the DDC modes for SDVO LVDS outputs (outside
the initial fixed mode setup). intel_panel_mode_valid() will
just reject most of them anyway, and any left over are entirely
pointless as they'll match the fixed mode hdisp+vdisp+vrefresh
so no user visible effect from using them instead of the fixed
mode.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026101134.20865-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Get rid of this funny byte based dumping of invalid output
flags and just dump it as a single hex numbers. Also do that
early since all the rest is going to get skipped anyway of
the thing is zero.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026101134.20865-5-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Call intel_sdvo_select_ddc_bus() before initializing any
of the outputs. And before that is functional (assuming no VBT)
we have to set up the controlled_outputs thing. Otherwise DDC
won't be functional during the output init but LVDS really
needs it for the fixed mode setup.
Note that the whole multi output support still looks very
bogus, and more work will be needed to make it correct.
But for now this should at least fix the LVDS EDID fixed mode
setup.
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/7301
Fixes: aa2b88074a ("drm/i915/sdvo: Fix multi function encoder stuff")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026101134.20865-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Pull the SDVO audio state computation into a helper.
This is almost identical to intel_hdmi_has_audio(),
except the sink capabilities are stored under intel_sdvo
rather than intel_hdmi. Might be nice to get rid of
this duplication eventually...
Cc: Chaitanya Kumar Borah <chaitanya.kumar.borah@intel.com>
Cc: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221026170150.2654-16-ville.syrjala@linux.intel.com
Since commit a5810f551d ("drm/i915: Allow more varied alternate
fixed modes for panels") intel_panel_add_edid_alt_fixed_modes()
no longer considers vrr vs. drrs separately. So no reason to
pass them as separate parameters either.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220927180615.25476-2-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
All the connectors are zero initialized so no need to clear
the *_allowed flags we don't support. Only leave the ones we want
to set. And while at it switch to booleans instead of ints.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220912111814.17466-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Each LFP may have different panel type which is stored in LFP data
data block. Based on the child device index respective panel-type/
panel-type2 field will be used.
v1: Initial rfc verion.
v2: Based on review comments from Jani,
- Used panel-type instead addition panel-index variable.
- DEVICE_HANDLE_* name changed and placed before DEVICE_TYPE_*
macro.
v3:
- passing intel_bios_encoder_data as argument of
intel_bios_init_panel(). Passing NULL to indicate encoder is not
initialized yet for dsi as current focus is to enable dual EDP. [Jani]
v4:
- encoder->devdata used which is initialized before from vbt
structure. [Jani]
Signed-off-by: Animesh Manna <animesh.manna@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220620065138.5126-1-animesh.manna@intel.com
It seem that when dealing with VRR capable eDP panels we need
to accept fixed modes with variable vblank length (which is what
VRR varies dynamically). Typically the preferred mode seems to be
a non-VRR more (lowish dotclock/refresh rate + short vblank).
We also have examples where it looks like even the hblank length
is a bit different between the preferred mode vs. VRR mode(s).
So let's just accept anything that has matching hdisp+vdisp+flags.
v2: Document that is_alt_drrs_mode() is a subset of is_alt_vrr_mode() (Jani)
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/125
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220531191844.11313-4-ville.syrjala@linux.intel.com
Apparently when the VBT panel_type==0xff we should trawl through
the PNPID table and check for a match against the EDID. If a
match is found the index gives us the panel_type.
Tried to match the Windows behaviour here with first looking
for an exact match, and if one isn't found we fall back to
looking for a match w/o the mfg year/week.
v2: Rebase due to vlv_dsi changes
v3: Adjust to .get_panel_type() vfunc
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/5545
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-14-ville.syrjala@linux.intel.com
Move the panel specific VBT parsing to happen during the
output probing stage. Needs to be done because the VBT
parsing will need to look at the EDID to determine
the correct panel_type on some machines.
We split the parsed VBT data (i915->vbt) along the same
boundary. For the moment we just hoist all the panel
specific stuff into connector->panel.vbt since that seems
like the most convenient place for eg. the backlight code.
Note that we simply drop the drrs type check from
intel_drrs_frontbuffer_update() since that operates on the whole
device rather than a specific connector/encoder. But the check
was just a micro optimization so removing it doesn't actually
mattter for correctness.
TODO: Lot's of cleanup to be done in the future. Eg. most of
the DSI stuff could probably be eliminated entirely and just
parsed on demand during DSI init.
v2: Note the intel_drrs_frontbuffer_update() change
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220510104242.6099-13-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Move DRM's HMDI helpers into the display/ subdirectoy and add it
to DRM's display helpers. Update all affected drivers. No functional
changes.
The HDMI helpers were implemented in the EDID and connector code, but
are actually unrelated. With the move to the display-helper library, we
can remove the dependency on drm_edid.{c,h} in some driver's HDMI source
files.
Several of the HDMI helpers remain in EDID code because both share parts
of their implementation internally. With better refractoring of the EDID
code, those HDMI helpers could be moved into the display-helper library
as well.
v3:
* fix Kconfig dependencies (Javier)
v2:
* reduce HDMI helpers to avoid exporting functions (Jani)
* fix include statements (Jani, Javier)
* update Kconfig symbols
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220421073108.19226-8-tzimmermann@suse.de
The intel_panel_add_edid_fixed_mode() vs.
intel_panel_add_edid_downclock_mode() split is not really
helpful. Let's just roll those into a single function so
that the connector init code doesn't have to care too much
about this. All we need to know is whether DRRS should be
allowed or not.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Rather than having the connector init get the fixed mode back from
intel_panel and then feed it straight back into intel_panel_init()
let's just make the fixed mode lookup put the mode directly onto
the panel's fixed_modes list. Avoids the pointless round trip and
opens the door for further enhancements to the fixed mode handling.
v2: Make the debug message correct by using intel_panel_drrs_type() (Jani)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220331112822.11462-3-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
