The ath11k active pdevs are protected by RCU but the gtk offload status
event handling code calling ath11k_mac_get_arvif_by_vdev_id() was not
marked as a read-side critical section.
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Compile tested only.
Fixes: a16d9b50cf ("ath11k: support GTK rekey offload")
Cc: stable@vger.kernel.org # 5.18
Cc: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019155342.31631-1-johan+linaro@kernel.org
The ath11k active pdevs are protected by RCU but the DFS radar event
handling code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section.
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Compile tested only.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Cc: stable@vger.kernel.org # 5.6
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019153115.26401-3-johan+linaro@kernel.org
The ath11k active pdevs are protected by RCU but the temperature event
handling code calling ath11k_mac_get_ar_by_pdev_id() was not marked as a
read-side critical section as reported by RCU lockdep:
=============================
WARNING: suspicious RCU usage
6.6.0-rc6 #7 Not tainted
-----------------------------
drivers/net/wireless/ath/ath11k/mac.c:638 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
rcu_scheduler_active = 2, debug_locks = 1
no locks held by swapper/0/0.
...
Call trace:
...
lockdep_rcu_suspicious+0x16c/0x22c
ath11k_mac_get_ar_by_pdev_id+0x194/0x1b0 [ath11k]
ath11k_wmi_tlv_op_rx+0xa84/0x2c1c [ath11k]
ath11k_htc_rx_completion_handler+0x388/0x510 [ath11k]
Mark the code in question as an RCU read-side critical section to avoid
any potential use-after-free issues.
Tested-on: WCN6855 hw2.1 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Fixes: a41d10348b ("ath11k: add thermal sensor device support")
Cc: stable@vger.kernel.org # 5.7
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231019153115.26401-2-johan+linaro@kernel.org
In WMI layer module, the identifier wmi_sc is used to represent
an instance of ath11k_wmi_base structure. However, within ath11k,
the convention is to use "ab" to represent an SoC "base" struct.
So change the all instances of wmi_sc to wmi_ab.
Compile tested only.
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231014032650.32605-2-quic_periyasa@quicinc.com
Currently, the logic to return an ath11k_sta pointer, given a
ieee80211_sta pointer, uses typecasting throughout the driver. In
general, conversion functions are preferable to typecasting since
using a conversion function allows the compiler to validate the types
of both the input and output parameters.
ath11k already defines a conversion function ath11k_vif_to_arvif() for
a similar conversion. So introduce ath11k_sta_to_arsta() for this use
case, and convert all of the existing typecasting to use this
function.
No functional changes, compile tested only.
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231009-ath11k_sta_to_arsta-v1-1-1563e3a307e8@quicinc.com
Certain regulatory domains could put restrictions on phy mode operation.
For example, in a few countries HE Operation is not allowed. For such
countries, firmware indicates this via phy bitmap in each reg rule.
Currently, there is no logic to parse this info and then pass it on to the
cfg80211/regulatory.
Add parsing of this phy bitmap from the regulatory channel change event and
then accordingly map it to cfg80211/regulatory flags and pass it on to it.
While at it, correct typo in debug print s/dsf/dfs.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231004092655.25020-1-quic_adisi@quicinc.com
No need cast (void *) to (struct ath11k_base *),
struct hal_rx_msdu_link *), (struct ath11k_buffer_addr *) or
other types.
Signed-off-by: Wu Yunchuan <yunchuan@nfschina.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230919045150.524304-1-yunchuan@nfschina.com
Remove set but otherwise unused 'wlan_init_status' and
'wmi_ready' members of 'struct ath11k_base', adjust
'ath11k_wmi_tlv_rdy_parse()' accordingly.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230824075121.121144-2-dmantipov@yandex.ru
Memory allocated for firmware pdev, vdev and beacon statistics
are not released during rmmod.
Fix it by calling ath11k_fw_stats_free() function before hardware
unregister.
While at it, avoid calling ath11k_fw_stats_free() while processing
the firmware stats received in the WMI event because the local list
is getting spliced and reinitialised and hence there are no elements
in the list after splicing.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230606091128.14202-1-quic_adisi@quicinc.com
According to Documentation/core-api/printk-formats.rst %pK should not be used
with printk(), so switch back to using just %p. printk() will hash the address
so addresses are not leaked to user space.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-14-kvalo@kernel.org
Add debug messages for every command and cleanup the existing ones to make them
all follow the same style. For better readability start every message with
"cmd". Print the debug message after a successful ath11k_wmi_cmd_send() call.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-9-kvalo@kernel.org
Also these functions don't follow the preferred style so fix those.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-8-kvalo@kernel.org
The error handling doesn't follow the preferred style so fix that.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-7-kvalo@kernel.org
Now that we have a default handler there's no need anymore to list every
unsupported event id anymore, so remove that to clean this up.
While at it remove the pointless todo comment and change the debug message to
follow the preferred style.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-6-kvalo@kernel.org
Add a debug message for every WMI event to make it easier track what's
happening in WMI. For better readability start every debug message with
"event".
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-5-kvalo@kernel.org
Now that the previous patch changed ath11k_dbg() to print the debug level
there's no need to have the level in the actual message anymore. So remove those.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3.6510.23
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230609142440.24643-4-kvalo@kernel.org
Add support to process factory test mode commands (FTM) for calibration.
By default firmware start with NORMAL mode and to process the FTM commands
firmware needs to be restarted in FTM mode using module parameter ftm_mode.
The pre-request is all the radios should be down before starting the test.
When start command ATH11K_TM_CMD_TESTMODE_START is received, ar->state
is set to Test Mode. If the FTM command or event length is greater
than 256 bytes, it will be broken down into multiple segments and
encoded with TLV header if it is segmented commands, else it is sent
to firmware as it is.
On receiving UTF event from firmware, if it is segmented event, the driver
will wait until it receives all the segments and notify the complete
data to user application. In case the segmented sequence are missed or
lost from the firmware, driver will skip the already received partial data.
In case of unsegmented UTF event from firmware, driver notifies the
data to the user application as it comes. Applications handles
the data further.
Command to boot in ftm mode:
insmod ath11k ftm_mode=1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Govindaraj Saminathan <quic_gsaminat@quicinc.com>
Co-developed-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Sowmiya Sree Elavalagan <quic_ssreeela@quicinc.com>
Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230517135934.16408-4-quic_rajkbhag@quicinc.com
Add new function ath11k_mac_setup_bcn_tmpl_ema() which invokes the new
API provided by MAC80211 to retrieve EMA beacons.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230405221648.17950-8-quic_alokad@quicinc.com
- Split ath11k_mac_setup_bcn_tmpl() to move the beacon retrieval and
WMI command to a new function, ath11k_mac_setup_bcn_tmpl_legacy().
In the original function add checks to use the transmitting interface
when MBSSID is enabled.
- Set rsnie_present and wpaie_present fields for the non-transmitting
interfaces when MBSSID is enabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230405221648.17950-7-quic_alokad@quicinc.com
Include MBSSID parameters in WMI vdev up operation.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230405221648.17950-5-quic_alokad@quicinc.com
Rename trans_bssid to tx_vdev_bssid to make it similar to vdev_bssid.
Rename profile_num to nontx_profile_cnt, and profile_idx to
nontx_profile_idx which makes it clear that these store configurations
related to MBSSID non-transmitting profiles.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230405221648.17950-4-quic_alokad@quicinc.com
Configure multiple BSSID flags and index of the transmitting interface
in vdev create/start commands depending on the service bit
WMI_TLV_SERVICE_MBSS_PARAM_IN_VDEV_START_SUPPORT.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230405221648.17950-3-quic_alokad@quicinc.com
Advertise the driver support for multiple BSSID (MBSSID) and
enhanced multi-BSSID advertisements (EMA) by setting extended
capabilities.
Configure mbssid_max_interfaces and ema_max_profile_periodicity
fields in structure wiphy which are used to advertise maximum number
of interfaces and profile periodicity supported by the driver.
Add new WMI fields to configure maximum vdev count supported for
MBSSID and profile periodicity in case of EMA.
Setting WMI_RSRC_CFG_FLAG2_CALC_NEXT_DTIM_COUNT_SET flag
indicates that the firmware should track and update the DTIM counts
for each non-transmitted profile.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aloka Dixit <quic_alokad@quicinc.com>
Co-developed-by: John Crispin <john@phrozen.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230405221648.17950-2-quic_alokad@quicinc.com
ath11k_wmi_fw_stats_num_vdevs() and ath11k_wmi_fw_stats_num_bcn() really
look the same as list_count_nodes(), so use the latter instead of hand
writing it.
The first ones use list_for_each_entry() and the other list_for_each(), but
they both count the number of nodes in the list.
While at it, also remove to prototypes of non-existent functions.
Based on the names and prototypes, it is likely that they should be
equivalent to list_count_nodes().
Compile tested only.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/941484caae24b89d20524b1a5661dd1fd7025492.1682542084.git.christophe.jaillet@wanadoo.fr
This is a regression fix for 80+80 and 160 MHz support bits being
cleared, therefore not adverised. Remove disable of 80+80 and 160 MHz
capability flags and assign valid center frequency 2 similar to
VHT80_80.
Fixes: 38dfe775d0 ("wifi: ath11k: push MU-MIMO params from hostapd to hardware")
Reported-by: Robert Marko <robert.marko@sartura.hr>
Tested-by: Robert Marko <robert.marko@sartura.hr> # IPQ8074 WLAN.HK.2.9.0.1-01385-QCAHKSWPL_SILICONZ-1
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217299
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: Muna Sinada <quic_msinada@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1681762947-13882-1-git-send-email-quic_msinada@quicinc.com
The WMI management rx event has multiple arrays of TLVs, however the common
WMI TLV parser won't handle multiple TLV tags of same type.
So the multiple array tags of WMI management rx TLV is parsed incorrectly
and the length calculated becomes wrong when the target sends multiple
array tags.
Add separate TLV parser to handle multiple arrays for WMI management rx
TLV. This fixes invalid length issue when the target sends multiple array
tags.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Nagarajan Maran <quic_nmaran@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230320133840.30162-1-quic_nmaran@quicinc.com
Add some more debug prints in processing regulatory WMI event in order to
increase more debuggability.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-4-quic_adisi@quicinc.com
In order to support different power levels of 6 GHz AP and client,
new WMI event for regulatory - WMI_REG_CHAN_LIST_CC_EXT_EVENTID is
added in firmware. This event provides new parameters required for
6 GHz regulatory rules.
Add support for parsing 2.4 GHz, 5 GHz and 6 GHz reg rules and other
parameters from WMI_REG_CHAN_LIST_CC_EXT_EVENTID.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Lavanya Suresh <quic_lavaks@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-3-quic_adisi@quicinc.com
Currently, during regulatory event, 2 GHz/5 GHz is referred
to as 2G/5G including variable names. However, there is no
such entity as 2G or 5G.
Re-name such occurences to its proper name. No functional changes.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230110121024.14051-2-quic_adisi@quicinc.com
Add support to notify tx ack signal values for management
packets to userspace through nl80211 interface.
Advertise NL80211_EXT_FEATURE_ACK_SIGNAL_SUPPORT flag
to enable this feature and it will be used for data
packets as well.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.7.0.1-01744-QCAHKSWPL_SILICONZ-1
Signed-off-by: Abinaya Kalaiselvan <quic_akalaise@quicinc.com>
Signed-off-by: Maharaja Kennadyrajan <quic_mkenna@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221219053844.4084486-1-quic_mkenna@quicinc.com
Set the WMI_SCAN_FLAG_EXT_PASSIVE_SCAN_START_TIME_ENHANCE flag
while sending the scan command. If this flag is enabled when the
incoming scan request comes with a strict start time and its duration
overlaps with next TBTT, then target adjust the start time accordingly
for passive scan. Target supporting this feature will advertise
WMI_TLV_SERVICE_PASSIVE_SCAN_START_TIME_ENHANCE.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01467-QCAHKSWPL_SILICONZ-1
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20221222131720.11368-1-quic_tamizhr@quicinc.com
Somehow an extra 'e' slipped in there without anyone noticing,
drop that from ieeee80211_obss_color_collision_notify().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add support to get the following power save information through debugfs interface,
* Current ps state of the peer
* Time duration since the peer is in power save
* Total duration of the peer spent in power save
Above information is helpful in debugging the issues with power save clients.
This patch also add trace log support for PS timekeeper to track the PS state
change of the peers alongs with the peer MAC address and timestamp.
Use the below commands to get the above power save information,
To know the time_since_station_in_power_save:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/current_ps_duration
To know power_save_duration:
cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/
XX:XX:XX:XX:XX:XX/total_ps_duration
To reset the power_save_duration of all stations connected to AP:
echo 1 > /sys/kernel/debug/ieee80211/phyX/ath11k/reset_ps_duration
To enable/disable the ps_timekeeper:
echo Y > /sys/kernel/debug/ieee80211/phyX/ath11k/ps_timekeeper_enable
Y = 1 to enable and Y = 0 to disable.
To record PS timekeeer logs after enabling ps_timekeeper:
trace-cmd record -e ath11k_ps_timekeeper
Tested-on: Tested-on: IPQ8074 WLAN.HK.2.5.0.1-00991-QCAHKSWPL_SILICONZ-1
Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com>
Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220725054601.14719-1-quic_tamizhr@quicinc.com
Currently, firmware stats, comprising pdev, vdev and beacon stats are
part of debugfs. In firmware pdev stats, firmware reports the final
Tx power used to transmit each packet. If driver wants to know the
final Tx power being used at firmware level, it can leverage from
firmware pdev stats.
Move firmware stats out of debugfs context in order to leverage
the final Tx power reported in it even when debugfs is disabled.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220603082814.31466-2-quic_adisi@quicinc.com
In current code STA_KEEPALIVE_ARP_RESPONSE TLV header is included only
when ARP method is used, this causes firmware always to crash when wowlan
is enabled because firmware needs it to be present no matter ARP method
is used or not.
Fix this issue by including STA_KEEPALIVE_ARP_RESPONSE TLV header by
default.
Also fix below typo:
s/WMI_TAG_STA_KEEPALVE_ARP_RESPONSE/WMI_TAG_STA_KEEPALIVE_ARP_RESPONSE/
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Fixes: 0f84a156aa ("ath11k: Handle keepalive during WoWLAN suspend and resume")
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220913044358.2037-1-quic_bqiang@quicinc.com
Add support to connect to a non-transmit MBSSID AP profile.
Non-transmit MBSSID profile parameters are passed to the firmware
via WMI VDEV UP command and this helps firmware to track MBSSID
profile within the multi-BSS beacon and report beacon loss if
any.
WCN6750, QCA6390 & WCN6855 firmwares have the support and hence
enable the support on these hardwares.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220901080616.29414-1-quic_mpubbise@quicinc.com
Currently TWT debugfs files required for manually testing the
TWT feature are created only for the AP interfaces; these debugfs
hooks are also required for the station interfaces in order to
test the TWT feature manually, therefore create these debugfs
hooks for station iftype as well.
In the case of station interfaces, TWT is entirely handled in the
firmware based on input parameters passed to it during association
via TWT enable WMI command. In order to manually test this feature,
firmware expects to first disable the TWT feature and then send the
enable command with sta_cong_timer_ms parameter set to 0.
This is true for WCN6750, QCA6390 & WCN6855 hardwares.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220720135150.22193-2-quic_mpubbise@quicinc.com
Introduce the capability to specify gfp_t parameter to
ieeee80211_obss_color_collision_notify routine since it runs in
interrupt context in ieee80211_rx_check_bss_color_collision().
Fixes: 6d945a33f2 ("mac80211: introduce BSS color collision detection")
Co-developed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/02c990fb3fbd929c8548a656477d20d6c0427a13.1655419135.git.lorenzo@kernel.org
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
To add MLD, reuse the bss_conf structure later for per-link
information, so move some things into it that are per link.
Most transformations were done with the following spatch:
@@
expression sdata;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-sdata->vif.var
+sdata->vif.bss_conf.var
@@
struct ieee80211_vif *vif;
identifier var = { chanctx_conf, mu_mimo_owner, csa_active, color_change_active, color_change_color };
@@
-vif->var
+vif->bss_conf.var
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fix warnings reported by checkpatch tool. Below are the errors fixed,
drivers/net/wireless/ath/ath11k/hal_rx.c:760: 'recevied' may be misspelled - perhaps 'received?
drivers/net/wireless/ath/ath11k/qmi.c:2232: Prefer strscpy over strlcpy
drivers/net/wireless/ath/ath11k/qmi.c:2238: Prefer strscpy over strlcpy
drivers/net/wireless/ath/ath11k/qmi.c:2662: Prefer strscpy over strlcpy
drivers/net/wireless/ath/ath11k/mac.c:7836: 'atleast' may be misspelled - perhaps 'at least'?
drivers/net/wireless/ath/ath11k/wmi.c:6566: 'succeded' may be misspelled - perhaps 'succeeded'?
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00887-QCAMSLSWPLZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220602131350.29486-1-quic_mpubbise@quicinc.com
In case of Passpoint, the WLAN interface may be requested to
remain on a specific channel and then to send some management
frames on that channel. Now chanfreq of wmi_mgmt_send_cmd is set
as 0, as a result firmware may choose a default but wrong channel.
Fix it by assigning chanfreq field with the designated channel.
This change only applies to WCN6855 and QCA6390, other chips are
not affected.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-4-quic_bqiang@quicinc.com
Add remain on channel support, it is needed in several
scenarios such as Passpoint etc.
Currently this is supported by QCA6390, WCN6855, IPQ8074,
IPQ6018 and QCN9074.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506013614.1580274-2-quic_bqiang@quicinc.com
With WoWLAN enabled and after sleeping for a rather long time,
we are seeing that with some APs, it is not able to wake up
the STA though the correct wake up pattern has been configured.
This is because the host doesn't send keepalive command to
firmware, thus firmware will not send any packet to the AP and
after a specific time the AP kicks out the STA.
Fix this issue by enabling keepalive before going to suspend
and disabling it after resume back.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220506012540.1579604-1-quic_bqiang@quicinc.com
When test connect/disconnect to an AP frequently with WCN6855, sometimes
it show below log.
[ 277.040121] wls1: deauthenticating from 8c:21:0a:b3:5a:64 by local choice (Reason: 3=DEAUTH_LEAVING)
[ 277.050906] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050944] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050954] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050961] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.050967] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 277.050976] ath11k_pci 0000:05:00.0: wmi stats vdev id 0 mac 00:03:7f:29:61:11
[ 277.050983] ath11k_pci 0000:05:00.0: wmi stats bssid 8c:21:0a:b3:5a:64 vif pK-error
[ 277.050989] ath11k_pci 0000:05:00.0: not found station for bssid 8c:21:0a:b3:5a:64
[ 277.050995] ath11k_pci 0000:05:00.0: failed to parse rssi chain -71
[ 277.051000] ath11k_pci 0000:05:00.0: failed to pull fw stats: -71
[ 278.064050] ath11k_pci 0000:05:00.0: failed to request fw stats: -110
Reason is:
When running disconnect operation, sta_info removed from local->sta_hash
by __sta_info_destroy_part1() from __sta_info_flush(), after this,
ieee80211_find_sta_by_ifaddr() which called by
ath11k_wmi_tlv_fw_stats_data_parse() and ath11k_wmi_tlv_rssi_chain_parse()
cannot find this station, then failed log printed.
steps are like this:
1. when disconnect from AP, __sta_info_destroy() called __sta_info_destroy_part1()
and __sta_info_destroy_part2().
2. in __sta_info_destroy_part1(), it has "sta_info_hash_del(local, sta)"
and "list_del_rcu(&sta->list)", it will remove the ieee80211_sta from the
list of ieee80211_hw.
3. in __sta_info_destroy_part2(), it called drv_sta_state()->ath11k_mac_op_sta_state(),
then peer->sta is clear at this moment.
4. in __sta_info_destroy_part2(), it then called sta_set_sinfo()->drv_sta_statistics()
->ath11k_mac_op_sta_statistics(), then WMI_REQUEST_STATS_CMDID sent to firmware.
5. WMI_UPDATE_STATS_EVENTID reported from firmware, at this moment, the
ieee80211_sta can not be found again because it has remove from list in
step2 and also peer->sta is clear in step3.
6. in __sta_info_destroy_part2(), it then called cleanup_single_sta()->
sta_info_free()->kfree(sta), at this moment, the ieee80211_sta is freed
in memory, then the failed log will not happen because function
ath11k_mac_op_sta_state() will not be called.
Actually this print log is not a real error, it is only to skip parse the
info, so change to skip print by default debug setting.
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220428022426.2927-1-quic_wgong@quicinc.com
WCN6750 is a single PDEV non-DBS chip which supports 2G, 5G and 6G bands.
It is a single LMAC device which can be either hooked to 2G/5G/6G bands.
Add WMI changes to support WCN6750.
Tested-on: WCN6750 hw1.0 AHB WLAN.MSL.1.0.1-00573-QCAMSLSWPLZ-1
Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-01720.1-QCAHSPSWPL_V1_V2_SILICONZ_LITE-1
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00192-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <quic_mpubbise@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20220406094107.17878-11-quic_mpubbise@quicinc.com
