Currently QCN9274 supports only AP and station interface modes.
Add interface type mesh to ath12k_hw_params for
QCN9274 to provide support for mesh mode as well.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0-02903-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20231013070007.25597-2-quic_rgnanase@quicinc.com
RDDM is Ram Dump Debug Module which is used to debug issues when the
firmware encounters an error. The rddm_size is needed by the firmware
while MHI goes to the RDDM state. Provide the size to MHI subsystem so
that the firmware restart works when the firmware crashes.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230721055305.20420-2-quic_wgong@quicinc.com
When hardware rfkill is enabled in the firmware, it will report the
capability using WMI_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY event
to the host. Currently ath12k does not process this service capability. In
order to support this, update ath12k to check if the capability is enabled,
if so, send the GPIO information to firmware. When the firmware detects
hardware rfkill is enabled by the user, it will report it using
WMI_RFKILL_STATE_CHANGE_EVENTID. When ath12k receive the event, it will set
the value of rfkill_radio_on based on whether radio_state is equal to
WMI_RFKILL_RADIO_STATE_ON, then send WMI_PDEV_PARAM_RFKILL_ENABLE to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Acked-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230906110412.182176-1-quic_lingbok@quicinc.com
The PCIe PERST pin is currently pulled down on WCN7850 and it causes
some power leakage.
Fix it by notifying firmware not to pull down PCIe PERST pin in QMI
message for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230404032057.3236122-3-quic_cjhuang@quicinc.com
Currently the CNSS (Connectivity Subsystem) QMI feature is assigned to
qmi_wlanfw_host_cap_req_msg_v01 request directly, this prevents chip-specific
CNSS features from being added easily.
Solve this by adding a new field qmi_cnss_feature_bitmap to hw_params so
chip-specific CNSS features can be assigned to this field and later assigned to
qmi_wlanfw_host_cap_req_msg_v01 request.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230404032057.3236122-2-quic_cjhuang@quicinc.com
To reduce power consumption, change idle_ps to true to enable
Idle Mode Power Save (IMPS) for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20230317062533.18240-1-quic_bqiang@quicinc.com
ath12k is a new mac80211 driver for Qualcomm Wi-Fi 7 devices, first
supporting QCN9274 and WCN7850 PCI devices. QCN9274 supports both AP
and station; WCN7850 supports only station mode. Monitor mode is not
(yet) supported. Only PCI bus devices are supported.
ath12k is forked from an earlier version of ath11k. It was simpler to
have a "clean start" for the new generation and not try to share the
code with ath11k. This makes maintenance easier and avoids major
changes in ath11k, which would have significantly increased the risk
of regressions in existing setups.
ath12k uses le32 and cpu_to_le32() macros to handle endian
conversions, instead of using the firmware byte swap feature utilized
by ath11k. There is only one kernel module, named ath12k.ko.
Currently ath12k only supports HE mode (IEEE 802.11ax) or older, but
work is ongoing to add EHT mode (IEEE 802.11be) support.
The size of the driver is ~41 kLOC and 45 files. To make the review
easier, this initial version of ath12k does not support Device Tree,
debugfs or any other extra features. Those will be added later, after
ath12k is accepted to upstream.
The driver is build tested by Intel's kernel test robot with both GCC
and Clang. Sparse reports no warnings. The driver is mostly free of
checkpatch warnings, albeit few of the warnings are omitted on
purpose, list of them here:
https://github.com/qca/qca-swiss-army-knife/blob/master/tools/scripts/ath12k/ath12k-check#L52
The driver has had multiple authors who are listed in alphabetical
order below.
Co-developed-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Signed-off-by: Balamurugan Selvarajan <quic_bselvara@quicinc.com>
Co-developed-by: Baochen Qiang <quic_bqiang@quicinc.com>
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Co-developed-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Signed-off-by: Bhagavathi Perumal S <quic_bperumal@quicinc.com>
Co-developed-by: Carl Huang <quic_cjhuang@quicinc.com>
Signed-off-by: Carl Huang <quic_cjhuang@quicinc.com>
Co-developed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Co-developed-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com>
Co-developed-by: P Praneesh <quic_ppranees@quicinc.com>
Signed-off-by: P Praneesh <quic_ppranees@quicinc.com>
Co-developed-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com>
Co-developed-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Co-developed-by: Sriram R <quic_srirrama@quicinc.com>
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Co-developed-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Signed-off-by: Vasanthakumar Thiagarajan <quic_vthiagar@quicinc.com>
Co-developed-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
