[Why]
ramp_up_dispclk_with_dpp is to change dispclk, dppclk and dprefclk
according to bandwidth requirement. call stack: rv1_update_clocks -->
update_clocks --> dcn10_prepare_bandwidth / dcn10_optimize_bandwidth
--> prepare_bandwidth / optimize_bandwidth. before change dcn hw,
prepare_bandwidth will be called first to allow enough clock,
watermark for change, after end of dcn hw change, optimize_bandwidth
is executed to lower clock to save power for new dcn hw settings.
below is sequence of commit_planes_for_stream:
step 1: prepare_bandwidth - raise clock to have enough bandwidth
step 2: lock_doublebuffer_enable
step 3: pipe_control_lock(true) - make dchubp register change will
not take effect right way
step 4: apply_ctx_for_surface - program dchubp
step 5: pipe_control_lock(false) - dchubp register change take effect
step 6: optimize_bandwidth --> dc_post_update_surfaces_to_stream
for full_date, optimize clock to save power
at end of step 1, dcn clocks (dprefclk, dispclk, dppclk) may be
changed for new dchubp configuration. but real dcn hub dchubps are
still running with old configuration until end of step 5. this need
clocks settings at step 1 should not less than that before step 1.
this is checked by two conditions: 1. if (should_set_clock(safe_to_lower
, new_clocks->dispclk_khz, clk_mgr_base->clks.dispclk_khz) ||
new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz)
2. request_dpp_div = new_clocks->dispclk_khz > new_clocks->dppclk_khz
the second condition is based on new dchubp configuration. dppclk
for new dchubp may be different from dppclk before step 1.
for example, before step 1, dchubps are as below:
pipe 0: recout=(0,40,1920,980) viewport=(0,0,1920,979)
pipe 1: recout=(0,0,1920,1080) viewport=(0,0,1920,1080)
for dppclk for pipe0 need dppclk = dispclk
new dchubp pipe split configuration:
pipe 0: recout=(0,0,960,1080) viewport=(0,0,960,1080)
pipe 1: recout=(960,0,960,1080) viewport=(960,0,960,1080)
dppclk only needs dppclk = dispclk /2.
dispclk, dppclk are not lock by otg master lock. they take effect
after step 1. during this transition, dispclk are the same, but
dppclk is changed to half of previous clock for old dchubp
configuration between step 1 and step 6. This may cause p-state
warning intermittently.
[How]
for new_clocks->dispclk_khz == clk_mgr_base->clks.dispclk_khz, we
need make sure dppclk are not changed to less between step 1 and 6.
for new_clocks->dispclk_khz > clk_mgr_base->clks.dispclk_khz,
new display clock is raised, but we do not know ratio of
new_clocks->dispclk_khz and clk_mgr_base->clks.dispclk_khz,
new_clocks->dispclk_khz /2 does not guarantee equal or higher than
old dppclk. we could ignore power saving different between
dppclk = displck and dppclk = dispclk / 2 between step 1 and step 6.
as long as safe_to_lower = false, set dpclk = dispclk to simplify
condition check.
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Hersen Wu <hersenxs.wu@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
SMU may return error code to driver, but driver only check if response
is OK.
[How]
Check SMU response instead of reg_wait, assert in case of reponse isn't
OK.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Driver already get display clock from SMU base on MHz, but driver read
again and mutiple 1000 cause wait loop value is overflow.
[How]
remove coding error
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
First, to make code more consistent
Second, to get rid of those scenario where we create a second
local pointer to dc when it's already passed in.
[How]
Rename core_dc to dc
Remove duplicate local pointers to dc
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This value will be needed by dml and therefore should be externally
accessible.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
dc_destroy should only clean up SW, this is because GPUs may be
removed before driver unload, leading to HW to be unavailable.
[how]
remove GPIO close as part of GPIO destroy, this is unnecessary because
GPIO is not shared, and GPIOs are generally closed after being opened
Add tracking to HW access during destructor to make future issues
easier to pinpoint, and block access to prevent hangs.
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
underflow seen on certain monitor setups caused by making dcnxx_init_hw
generic
[How]
by moving dcn20_init_hw into dcn10, we added a dcn-specific clk_mgr
init (dc->clk_mgr->funcs->init_clocks()). Thus, put old clk_mgr
memset in an else statement so both memsets don't get set
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently every time DC wants to access firmware info we make a call
into VBIOS. This makes no sense as there is nothing that can change
runtime inside fw info and can cause issues when calling unstable
bios during bringup.
This change eliminate this behavior by only calling bios once for fw
info and keeping it stored as part of dc_bios.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Before for raven and navi we are calling pp_smu functions for pme
[how]
refactor a code so we will call clk_mgr's enable_pme_wa function so we
can use pme_wa for future asics. This way we don't need to worry about
different ASIC since clk_mgr already have that information
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.
[How]
- Pull get_active_display_cnt out to clk_mgr.
- Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for handling of clocking relevant to the DCN2 block,
including programming of the DCCG (Display Controller Clock Generator)
block:
HW Blocks:
+--------+ +--------+
| DIO | | DCCG |
+--------+ +--------+
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
-----BEGIN PGP SIGNATURE-----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=4uQX
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2019-06-14' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.3:
UAPI Changes:
Cross-subsystem Changes:
- Add code to signal all dma-fences when freed with pending signals.
- Annotate reservation object access in CONFIG_DEBUG_MUTEXES
Core Changes:
- Assorted documentation fixes.
- Use irqsave/restore spinlock to add crc entry.
- Move code around to drm_client, for internal modeset clients.
- Make drm_crtc.h and drm_debugfs.h self-contained.
- Remove drm_fb_helper_connector.
- Add bootsplash to todo.
- Fix lock ordering in pan_display_legacy.
- Support pinning buffers to current location in gem-vram.
- Remove the now unused locking functions from gem-vram.
- Remove the now unused kmap-object argument from vram helpers.
- Stop checking return value of debugfs_create.
- Add atomic encoder enable/disable helpers.
- pass drm_atomic_state to atomic connector check.
- Add atomic support for bridge enable/disable.
- Add self refresh helpers to core.
Driver Changes:
- Add extra delay to make MTP SDM845 work.
- Small fixes to virtio, vkms, sii902x, sii9234, ast, mcde, analogix, rockchip.
- Add zpos and ?BGR8888 support to meson.
- More removals of drm_os_linux and drmP headers for amd, radeon, sti, r128, r128, savage, sis.
- Allow synopsis to unwedge the i2c hdmi bus.
- Add orientation quirks for GPD panels.
- Edid cleanups and fixing handling for edid < 1.2.
- Add runtime pm to stm.
- Handle s/r in dw-hdmi.
- Add hooks for power on/off to dsi for stm.
- Remove virtio dirty tracking code, done in drm core.
- Rework BO handling in ast and mgag200.
Tiny conflict in drivers/gpu/drm/amd/display/dc/clk_mgr/clk_mgr.c,
needed #include <linux/slab.h> to make it compile.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/0e01de30-9797-853c-732f-4a5bd6e61445@linux.intel.com
refactor a code so we will call clk_mgr's enable_pme_wa function so we
can use pme_wa for future asics. This way we don't need to worry about
different ASIC since clk_mgr already have that information
Signed-off-by: Su Sung Chung <Su.Chung@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Some HW specific implementations can be pulled out into clk_mgr.c.
[How]
* Pull get_active_display_cnt out to clk_mgr.
* Pull out shared logic in set_dispclk and set_dprefclk
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Better organization
[How]
Move clk_mgr files under dc/clk_mgr
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
