This reverts commit f878122841 ("drm/amdgpu:
Fix bug where DPM is not enabled after hibernate and resume").
It was intended to fix Hawaii S4(hibernation) issue but break S3. As
ixFEATURE_STATUS is filled with garbage data on resume which can be
only cleared by reloading smc firmware(but that will involve many
changes). So, we will revert this S4 fix and seek a new way.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So that the succeeding resume can be performed based on
a clean state.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct some registers bitmasks and add mmBIOS_SCRATCH_7
reset.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid underflow seen on Polaris10 with some 3440x1440
144Hz displays. As the threshold of 190 us cuts too close
to minVBlankTime of 192 us.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
This patch is to add one sysfs file -- "pp_od_clk_voltage" for
Raven/Raven2/Picasso APU, which is only used by dGPU like VEGA10.
This sysfs file supports the feature to modify gfx engine clock(Mhz units), it can
be used to configure the min value and the max value for gfx clock limited in the
safe range.
Command guide:
echo "s level clock" > pp_od_clk_voltage
s - adjust teh sclk level
level - 0 or 1, "0" represents the min value, "1" represents the max value
clock - the clock value(Mhz units), like 400, 800 or 1200, the value must be within the
OD_RANGE limits.
Example:
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
smc, sdma, sos, ta and asd fw is not used in SRIOV. Skip them to
accelerate sw_init for navi12.
v2: skip above fw in SRIOV for vega10 and sienna_cichlid
v3: directly skip psp fw loading in SRIOV
Signed-off-by: Jingwen Chen <Jingwen.Chen2@amd.com>
Reviewed-by: Emily.Deng <Emily.Deng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SMU10_UMD_PSTATE_PEAK_FCLK value should not be used to set the DPM.
Suggested-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Different mclk dpm policy will be applied based on the VRAM
width.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Return value should be -EINVAL rather than EINVAL
Fixes: f83a9991648bb("drm/amd/powerplay: add Vega10 powerplay support (v5)")
Fixes: 2cac05dee6e30("drm/amd/powerplay: add the hw manager for vega12 (v4)")
Cc: Eric Huang <JinHuiEric.Huang@amd.com>
Cc: Evan Quan <evan.quan@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Xiaoliang Pang <dawning.pang@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
SMU FCLK,SOCCLK have dependency on VCN CLKs. Lower VCN values so that
FCLK, SOCCLK reflect values set by UMD Stable Pstate.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Which tells it's a normal pstate change or memory retraining.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Tested-by: Changfeng Zhu <Changfeng.Zhu@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On my R9 390, the voltage was reported as a constant 1000 mV.
This was due to a bug in smu7_hwmgr.c, in the smu7_read_sensor()
function, where some magic constants were used in a condition,
to determine whether the voltage should be read from PLANE2_VID
or PLANE1_VID. The VDDC mask was incorrectly used, instead of
the VDDGFX mask.
This patch changes the code to use the correct defined constants
(and apply the correct bitshift), thus resulting in correct voltage reporting.
Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starting in Linux 5.8, the graphics and memory clock frequency were not being
reported for CIK cards. This is a regression, since they were reported correctly
in Linux 5.7.
After investigation, I discovered that the smum_send_msg_to_smc() function,
attempts to call the corresponding get_argument() function of ci_smu_funcs.
However, the get_argument() function is not defined in ci_smu_funcs.
This patch fixes the bug by specifying the correct get_argument() function.
Fixes: a0ec225633 ("drm/amd/powerplay: unified interfaces for message issuing and response checking")
Signed-off-by: Sandeep Raghuraman <sandy.8925@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Normally softwareshutdowntemp should be greater than Thotspotlimit.
However, on some VEGA10 ASIC, the softwareshutdowntemp is 91C while
Thotspotlimit is 105C. This seems not right and may trigger some
false alarms.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC uses these to raise the voltage as needed for higher dispclk/dppclk
and to ensure that we have enough bandwidth to drive the displays.
There's a bug preventing these from actuially sending messages since
it's checking the actual clock (which is 0) instead of the incoming
clock (which shouldn't be 0) when deciding to send the hardmin.
[How]
Check the clocks != 0 instead of the actual clocks.
Fixes: 9ed9203c3e ("drm/amd/powerplay: rv dal-pplib interface refactor powerplay part")
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Do the maths in celsius degree. This can fix the issues caused
by the changes below:
drm/amd/pm: correct Vega20 swctf limit setting
drm/amd/pm: correct Vega12 swctf limit setting
drm/amd/pm: correct Vega10 swctf limit setting
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kenneth Feng <kenneth.feng@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct the Vega20 thermal swctf limit.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct the Vega12 thermal swctf limit.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct the Vega10 thermal swctf limit.
Bug: https://gitlab.freedesktop.org/drm/amd/-/issues/1267
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In init_powerplay_table_information() the value returned from kmalloc()
is cast unnecessarily. Remove cast.
Issue identified with Coccinelle.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove asic_reg/nbio/nbio_6_1_offset.h which is included more than once
Reviewed-by: Evan Quan <evan.quan@amd.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wang Hai <wanghai38@huawei.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
if other threads have holden the reset lock, recovery will
fail to try_lock. Therefore we introduce atomic hive->in_reset
and adev->in_gpu_reset, to avoid reentering GPU recovery.
v2:
drop "? true : false" in the definition of amdgpu_in_reset
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Dennis Li <Dennis.Li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The target is to provide a clear entry point(for power routines).
Also this can help to maintain a clear view about the frameworks
used on different ASICs. Hopefully all these can make power part
more friendly to play with.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
