This reverts commit 76d164f582.
PCIe hung issue was observed on multiple platforms. The issue was reproduced
when DUT was configured as AP and associated with 50+ STAs.
For QCA9984/QCA9888, the DMA_BURST_SIZE register controls the AXI burst size
of the RD/WR access to the HOST MEM.
0 - No split , RAW read/write transfer size from MAC is put out on bus
as burst length
1 - Split at 256 byte boundary
2,3 - Reserved
With PCIe protocol analyzer, we can see DMA Read crossing 4KB boundary when
issue happened. It broke PCIe spec and caused PCIe stuck. So revert
the default value from 0 to 1.
Tested: IPQ8064 + QCA9984 with firmware 10.4-3.10-00047
QCS404 + QCA9984 with firmware 10.4-3.9.0.2--00044
Synaptics AS370 + QCA9888 with firmware 10.4-3.9.0.2--00040
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When simulate random transfer fail for sdio write and read, it crash
sometimes.
Test steps:
1. Add config and update kernel:
CONFIG_FAIL_MMC_REQUEST=y
CONFIG_FAULT_INJECTION=y
CONFIG_FAULT_INJECTION_DEBUG_FS=y
2. run simulate fail:
cd /sys/kernel/debug/mmc1/fail_mmc_request
echo 10 > probability
echo 10 > times # repeat until hitting issues
3. it crash, the act len of ath10k_htc_hdr is higher than allocate len, it cause panic:
[ 99.723482] skbuff: skb_over_panic: text:00000000caa0f780 len:57013 put:57013 head:000000004116f24a data:0000000019ecb4dc tail:0xdef5 end:0x640 dev:<NULL>
[ 99.737697] ------------[ cut here ]------------
[ 99.742327] kernel BUG at /mnt/host/source/src/third_party/kernel/v4.19/net/core/skbuff.c:104!
[ 99.750937] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
[ 99.831154] Process kworker/0:2 (pid: 151, stack limit = 0x00000000728010bf)
[ 99.838200] CPU: 0 PID: 151 Comm: kworker/0:2 Tainted: G W 4.19.85 #48
[ 99.846022] Hardware name: MediaTek krane sku0 board (DT)
[ 99.851429] Workqueue: events sdio_irq_work
[ 99.855614] pstate: 60000005 (nZCv daif -PAN -UAO)
[ 99.860402] pc : skb_panic+0x64/0x68
[ 99.863974] lr : skb_panic+0x64/0x68
[ 99.867542] sp : ffffff8008833a90
[ 99.870850] x29: ffffff8008833ac0 x28: ffffffe52e337370
[ 99.876159] x27: ffffffe52e328a90 x26: 000000000000e0d0
[ 99.881469] x25: ffffffe52e336b60 x24: 000000000000deb5
[ 99.886779] x23: ffffffe52e340680 x22: ffffffe4efd47e00
[ 99.892088] x21: 000000000000deb5 x20: ffffffa516d85b4c
[ 99.897397] x19: ffffffa526928037 x18: 0000000000000000
[ 99.902706] x17: 000000000000003c x16: ffffffa5265b6c80
[ 99.908015] x15: 0000000000000006 x14: 3a76656420303436
[ 99.913325] x13: 0000000000029bf0 x12: 0000000000000000
[ 99.918634] x11: 0000000000000000 x10: 0000000000000000
[ 99.923943] x9 : a3b907e4b2783000 x8 : a3b907e4b2783000
[ 99.929253] x7 : 0000000000000000 x6 : ffffffa526f66d76
[ 99.934563] x5 : 0000000000000000 x4 : 0000000000000000
[ 99.939872] x3 : 000000000002a5ab x2 : ffffffe53feed918
[ 99.945182] x1 : ffffffe53fee4a08 x0 : 000000000000008e
[ 99.950491] Call trace:
[ 99.952937] skb_panic+0x64/0x68
[ 99.956165] skb_put+0x7c/0x84
[ 99.959224] ath10k_sdio_irq_handler+0x740/0xbb8 [ath10k_sdio]
[ 99.965055] process_sdio_pending_irqs+0x58/0x1a4
[ 99.969758] sdio_run_irqs+0x34/0x60
[ 99.973329] sdio_irq_work+0x1c/0x28
[ 99.974930] cros-ec-spi spi2.0: SPI transfer timed out
[ 99.976904] process_one_work+0x210/0x410
[ 99.976911] worker_thread+0x234/0x3dc
[ 99.976923] kthread+0x120/0x130
[ 99.982090] cros-ec-spi spi2.0: spi transfer failed: -110
[ 99.986054] ret_from_fork+0x10/0x18
[ 99.986063] Code: aa1403e2 2a1503e4 a90023e9 97e37d1a (d4210000)
[ 99.986068] ---[ end trace cb6d948c5a0fd6c7 ]---
[ 100.017250] Kernel panic - not syncing: Fatal exception
[ 100.018879] cros-ec-spi spi2.0: Command xfer error (err:-110)
[ 100.023659] SMP: stopping secondary CPUs
[ 100.023703] Kernel Offset: 0x251dc00000 from 0xffffff8008000000
[ 100.023707] CPU features: 0x0,2188200c
[ 100.023709] Memory Limit: none
The simulate fail of sdio is not a real sdio transter fail, it only
set an error status in mmc_should_fail_request after the transfer end,
actually the transfer is success, then sdio_io_rw_ext_helper will
return error status and stop transfer the left data. For example,
the really RX len is 286 bytes, then it will split to 2 blocks in
sdio_io_rw_ext_helper, one is 256 bytes, left is 30 bytes, if the
first 256 bytes get an error status by mmc_should_fail_request,then
the left 30 bytes will not read in this RX operation. Then when the
next RX arrive, the left 30 bytes will be considered as the header
of the read, the top 8 bytes will be considered as ath10k_htc_hdr,
but actually the 8 bytes is not the ath10k_htc_hdr, so the act_len
from this ath10k_htc_hdr is not correct, if it is a big value, such
as 57013, it will trigger skb_panic.
Drop the skb with invalid length will be reasonable.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes coccicheck warning:
drivers/net/wireless/ath/ath10k/htt_rx.c:2143:2-31: WARNING: Assignment of 0/1 to bool variable
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The WiFi firmware found on sm8150 requires that the QDSS clock is
ticking in order to operate, so add an optional clock to the binding to
allow this to be specified in the sm8150 dts and add the clock to the
list of clocks in the driver.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The description of ath10k_pci_dump_memory_sram() is inaccurate, an error
can never be returned, it is always the length. Update the comment to
reflect.
Fixes: 219cc084c6 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_pci_dump_memory_reg() will try to access memory of type
ATH10K_MEM_REGION_TYPE_IOREG however, if a hardware restart is in progress
this can crash a system.
Individual ioread32() time has been observed to jump from 15-20 ticks to >
80k ticks followed by a secure-watchdog bite and a system reset.
Work around this corner case by only issuing the read transaction when the
driver state is ATH10K_STATE_ON.
Tested-on: QCA9988 PCI 10.4-3.9.0.2-00044
Fixes: 219cc084c6 ("ath10k: add memory dump support QCA9984")
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ioremap has provided non-cached semantics by default since the Linux 2.6
days, so remove the additional ioremap_nocache interface.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Fix some typo:
s/to to/to/
s/even/event/
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of just having an airtime flag in debugfs, turn AQL into a proper
NL80211_EXT_FEATURE, so drivers can turn it on when they are ready, and so
we also expose the presence of the feature to userspace.
This also has the effect of flipping the default, so drivers have to opt in
to using AQL instead of getting it by default with TXQs. To keep
functionality the same as pre-patch, we set this feature for ath10k (which
is where it is needed the most).
While we're at it, split out the debugfs interface so AQL gets its own
per-station debugfs file instead of using the 'airtime' file.
[Johannes:]
This effectively disables AQL for iwlwifi, where it fixes a number of
issues:
* TSO in iwlwifi is causing underflows and associated warnings in AQL
* HE (802.11ax) rates aren't reported properly so at HE rates, AQL could
never have a valid estimate (it'd use 6 Mbps instead of up to 2400!)
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/r/20191212111437.224294-1-toke@redhat.com
Fixes: 3ace10f5b5 ("mac80211: Implement Airtime-based Queue Limit (AQL)")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For max bundle size 32, the bundle mask is not same with 8/16.
Change it to match the max bundle size of htc. Otherwise it
will not match with firmware, for example, when bundle count
is 17, then flags of ath10k_htc_hdr is 0x4, if without this
patch, it will be considered as non-bundled packet because it
does not have mask 0xF0, then trigger error message later:
payload length 56747 exceeds max htc length: 4088.
htc->max_msgs_per_htc_bundle is the min value of
HTC_HOST_MAX_MSG_PER_RX_BUNDLE and
msg->ready_ext.max_msgs_per_htc_bundle of ath10k_htc_wait_target,
it will be sent to firmware later in ath10k_htc_start, then
firmware will use it as the final max rx bundle count, in
WLAN.RMH.4.4.1-00029, msg->ready_ext.max_msgs_per_htc_bundle
is 32, it is same with HTC_HOST_MAX_MSG_PER_RX_BUNDLE, so the
final max rx bundle count will be set to 32 in firmware.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Fixes: 224776520e ("ath10k: change max RX bundle size from 8 to 32 for sdio")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For tcp RX, the quantity of tcp acks to remote is 1/2 of the quantity
of tcp data from remote, then it will have many small length packets
on TX path of sdio bus, then it reduce the RX packets's bandwidth of
tcp.
This patch enable napi on RX path, then the RX packet of tcp will not
feed to tcp stack immeditely from mac80211 since GRO is enabled by
default, it will feed to tcp stack after napi complete, if rx bundle
is enabled, then it will feed to tcp stack one time for each bundle
of RX. For example, RX bundle size is 32, then tcp stack will receive
one large length packet, its length is neary 1500*32, then tcp stack
will send a tcp ack for this large packet, this will reduce the tcp
acks ratio from 1/2 to 1/32. This results in significant performance
improvement for tcp RX.
Tcp rx throughout is 240Mbps without this patch, and it arrive 390Mbps
with this patch. The cpu usage has no obvious difference with and
without NAPI.
call stack for each RX packet on GRO path:
(skb length is about 1500 bytes)
skb_gro_receive ([kernel.kallsyms])
tcp4_gro_receive ([kernel.kallsyms])
inet_gro_receive ([kernel.kallsyms])
dev_gro_receive ([kernel.kallsyms])
napi_gro_receive ([kernel.kallsyms])
ieee80211_deliver_skb ([mac80211])
ieee80211_rx_handlers ([mac80211])
ieee80211_prepare_and_rx_handle ([mac80211])
ieee80211_rx_napi ([mac80211])
ath10k_htt_rx_proc_rx_ind_hl ([ath10k_core])
ath10k_htt_rx_pktlog_completion_handler ([ath10k_core])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
call stack for napi complete and send tcp ack from tcp stack:
(skb length is about 1500*32 bytes)
_tcp_ack_snd_check ([kernel.kallsyms])
tcp_v4_do_rcv ([kernel.kallsyms])
tcp_v4_rcv ([kernel.kallsyms])
local_deliver_finish ([kernel.kallsyms])
ip_local_deliver ([kernel.kallsyms])
ip_rcv_finish ([kernel.kallsyms])
ip_rcv ([kernel.kallsyms])
netif_receive_skb_core ([kernel.kallsyms])
netif_receive_skb_one_core([kernel.kallsyms])
netif_receive_skb ([kernel.kallsyms])
netif_receive_skb_internal ([kernel.kallsyms])
napi_gro_complete ([kernel.kallsyms])
napi_gro_flush ([kernel.kallsyms])
napi_complete_done ([kernel.kallsyms])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
__softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio does not support wow, this patch is to enable it. When system enter
sleep state, if wowlan is enabled, then sdio chip will keep power if
platform support keep power, after resume, it will not need to re-load
firmware again.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change log level from warn to dbg level of mpdu status
of sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After the firmware crashes ath10k recovers via ieee80211_reconfig(),
which eventually leads to firmware configuration and including the
encryption keys. However, because there is no new auth/assoc and
4-way-handshake, and firmware set the authorize flag after
4-way-handshake, so the authorize flag in firmware is not set in
firmware without 4-way-handshake. This will lead to a failure of data
transmission after recovery done when using encrypted connections like
WPA-PSK. Set authorize flag after installing keys to firmware will fix
the issue.
This was noticed by testing firmware crashing using simulate_fw_crash
debugfs file.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For sdio chip, the max credit size in firmware is 1556, the 1556
include payload, ieee80211 header, htt header, htc header. So it
need to set the max mtu to 1500 to forbidden TX packet which exceed
1500 form application.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On SDIO chips the firmware log does not impact performance. To make it
easier to debug firmware problems keep it enabled on the firmware.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console if
firmware doesn't support some optional HTC services, ex:pktlog.
It is likely some older fw version may not support PKTLOG HTC
service as legacy fw uses HTC DATA service for pktlog.
Move this log to debug level to remove un-necessary warn message
on console.
htc.c:803: ath10k_warn(ar, "unsupported HTC service id: %d\n",
htc.c:881: ath10k_warn(ar, "unsupported HTC service id: %d\n",
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework event_create_dir() to use an array of static data instead of
function pointers where possible.
The problem is that it would call the function pointer on module load
before parse_args(), possibly even before jump_labels were initialized.
Luckily the generated functions don't use jump_labels but it still seems
fragile. It also gets in the way of changing when we make the module map
executable.
The generated function are basically calling trace_define_field() with a
bunch of static arguments. So instead of a function, capture these
arguments in a static array, avoiding the function call.
Now there are a number of cases where the fields are dynamic (syscall
arguments, kprobes and uprobes), in which case a static array does not
work, for these we preserve the function call. Luckily all these cases
are not related to modules and so we can retain the function call for
them.
Also fix up all broken tracepoint definitions that now generate a
compile error.
Tested-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191111132458.342979914@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
So far, frames were forwarded regardless of the FCS correctness leading
to userspace applications listening on the monitor mode interface to
receive potentially broken frames, even with the "fcsfail" flag unset.
By default, with the "fcsfail" flag of a monitor mode interface
unset, frames with FCS errors should be dropped. With this patch, the
fcsfail flag is taken into account correctly.
Tested-on: QCA4019 firmware-5-ct-full-community-12.bin-lede.011
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iw command only show rssi without each chain's rssi on sdio
iw wlan0 station dump
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 dBm
signal avg: -82 dBm
after this patch, it will show each chain's rssi on sdio
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 [-84, -88] dBm
signal avg: -82 [-84, -87] dBm
For QCA6174 PCIe, the ppdu have the correct rssi of each chain, it
indicate rssi of rx data by ath10k_htt_rx_h_signal. For sdio chip, the
rssi of each chain stored in rx management reported by firmware, the
ath10k_wmi_tlv_op_pull_mgmt_rx_ev which used for tlv wmi will get the
rssi of each chain and stored them in wmi_mgmt_rx_ev_arg, then indicate
them to mac80211. For non-tlv wmi chip, it will not get the rssi of each
chain and not indicate to mac80211, for non-tlv wmi chip, this patch will
not have impact. For tlv wmi chip, if the rssi of chain in mgmt is valid,
it will be indicate to mac80211, tested with QCA6174 PCIe/SDIO, the rssi
of 2 chain in mgmt is valid.
rssi of chains in mgmt of QCA6174 SDIO:
92096.652780: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[0]:70
92096.657324: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[1]:68
92096.662009: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[2]:128
92096.666647: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[3]:128
rssi of chains in mgmt of QCA6174 PCIe:
[ 1581.049816] ath10k_pci 0000:02:00.0: mgmt rssi[0]:17
[ 1581.049818] ath10k_pci 0000:02:00.0: mgmt rssi[1]:22
[ 1581.049821] ath10k_pci 0000:02:00.0: mgmt rssi[2]:128
[ 1581.049823] ath10k_pci 0000:02:00.0: mgmt rssi[3]:128
after apply this patch, the iw's rssi of PCIe do not changed, result is
same with before.
iw wlan0 station dump of QCA6174 PCIe:
Station 6c:e8:73:b8:92:dc (on wlan0)
signal: -70 [-77, -72] dBm
signal avg: -69 [-78, -72] dBm
iw wlan-5000mhz station dump of QCA9984 PCIe
connected with 2 client which has 2 chain:
Station 70:48:0f:1f:1a:b2 (on wlan-5000mhz)
signal: -47 [-55, -48, -87, -88] dBm
signal avg: -42 [-50, -43, -83, -86] dBm
Station ac:c1:ee:39:e3:83 (on wlan-5000mhz)
signal: -43 [-46, -45, -79, -84] dBm
signal avg: -43 [-46, -46, -82, -83] dBm
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Tested with QCA9984 PCIe with firmware 10.4-3.9.0.2-00040.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the BDF download QMI message has the end field set to 1, it signals
the end of the transfer, and triggers the firmware to do a CRC check. The
BDFs for msm8998 devices fail this check, yet the firmware is happy to
still use the BDF. It appears that this error is not caught by the
downstream drive by concidence, therefore there are production devices
in the field where this issue needs to be handled otherwise we cannot
support wifi on them. So, attempt to detect this scenario as best we can
and treat it as non-fatal.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ath10k_qmi_init() fails, the error handling does not free the irq
resources, which causes an issue if we EPROBE_DEFER as we'll attempt to
(re-)register irqs which are already registered.
Fix this by doing a power off since we just powered on the hardware, and
freeing the irqs as error handling.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add NL80211_FEATURE_ND_RANDOM_MAC_ADDR for NLO will enable the random
mac address for netdetect case.
iw command:
iw phy0 wowlan enable net-detect net-detect
randomize=AA:7B:A1:AC:B2:41/FF:FF:FF:FF:FF:FF interval 5000 delay 30
freqs 2412 matches ssid foo.
After suspend, DUT will send probe request with mac AA:7B:A1:AC:B2:41.
WCN3990, QCA9377, QCA6174 PCI also support this feature.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware with the build id QC_IMAGE_VERSION_STRING=WLAN.HL.1.0.2-XXXX does
not support the QMI_WLFW_HOST_CAP_REQ_V01 message and will return the
QMI not supported error to the ath10k driver. Since not supporting this
message is not fatal to the firmware nor the ath10k driver, lets catch
this particular scenario and ignore it so that we can still bring up
wifi services successfully.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Download firmware time cost of SDIO is too long, it is about 480ms,
add large size 2048 bytes for BMI download for SDIO chip, its time
cost will reduced to 240ms.
This will optimize the download firmware time cost.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the tlv len is set to the total len of the wmi cmd, it will trigger
firmware crash, correct the tlv len.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174
PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For RX, it has two parts, one is to read data from sdio, another
is to indicate the packets to upper stack. Recently it has only
one thread to do all RX things, it results that it is sequential
for RX and low throughout, change RX to parallel for the two parts
will increase throughout.
This patch move the indication to a workqueue, it results in
significant performance improvement on RX path.
Udp rx throughout is 200Mbps without this patch, and it arrives
400Mbps with this patch.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The max bundle size support by firmware is 32, change it from 8 to 32
will help performance. This results in significant performance
improvement on RX path.
The real max rx bundle is decided in ath10k_htc_wait_target(),
it is the min value of HTC_HOST_MAX_MSG_PER_RX_BUNDLE and the value reported
from firmware. So this change shouldn't cause any regressions with other
hardware supported by ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The existing implementation of initiating multiple sdio transfers for
receive bundling is slowing down the receive speed. Combining the
transfers using a bundle method would be ideal.
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unless we sleep for a while before transitioning the MSA memory to WLAN
the MPSS.AT.4.0.c2-01184-SDM845_GEN_PACK-1 firmware triggers a security
violation fairly reliably. Unforutnately recovering from this failure
always results in the entire system freezing.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 334f5b61a6.
This caused ath10k_snoc on Qualcomm MSM8998, SDM845 and QCS404 platforms to
trigger an assert in the firmware:
err_qdi.c:456:EF:wlan_process:1:cmnos_thread.c:3900:Asserted in wlan_vdev.c:_wlan_vdev_up:3219
Revert the offending commit for now.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Downloading ath10k firmware needs a large number of IOs and
cpuidle's miss predictions make it worse. In the worst case,
resume time can be three times longer than the average on sdio.
This patch disables cpuidle during firmware downloading by
applying PM_QOS_CPU_DMA_LATENCY in ath10k_download_fw().
Tested-on: QCA9880
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00029
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA number was not restored if OOM happened.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00018
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k does not provide transmit rate info per MSDU
in tx completion, mark that as -1 so mac80211
will ignore the rates. This fixes mac80211 update Mesh
link metric with invalid transmit rate info.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Hou Bao Hou <houbao@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The `ar_usb` field of `ath10k_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath10k_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath10k_usb_setup_pipe_resources`:
for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
endpoint = &iface_desc->endpoint[i].desc;
// get the address from endpoint descriptor
pipe_num = ath10k_usb_get_logical_pipe_num(ar_usb,
endpoint->bEndpointAddress,
&urbcount);
......
// select the pipe object
pipe = &ar_usb->pipes[pipe_num];
// initialize the ar_usb field
pipe->ar_usb = ar_usb;
}
The driver assumes that the addresses reported in endpoint
descriptors from device side to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath10k_usb_alloc_urb_from_pipe` and
`ath10k_usb_free_urb_to_pipe`.
This patch fixes the bug by preventing potential NULL-ptr-deref.
Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[groeck: Add driver tag to subject, fix build warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value of dma_map_single() should be checked for errors using
dma_mapping_error() and the skb has been dequeued so it needs to be
freed.
This was found when enabling CONFIG_DMA_API_DEBUG and it warned about the
missing dma_mapping_error() call.
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The memory of ar->debug.tpc_stats_final is reallocated every debugfs
reading, it should be freed in ath10k_debug_destroy() for the last
allocation.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If firmware reports rate_max > WMI_TPC_RATE_MAX(WMI_TPC_FINAL_RATE_MAX)
or num_tx_chain > WMI_TPC_TX_N_CHAIN, it will cause array out-of-bounds
access, so print a warning and reset to avoid memory corruption.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when pointer crash_data is null the present null check
will also check that crash_data->ramdump_buf is null and will cause
a null pointer dereference on crash_data. Fix this by using the ||
operator instead of &&.
Fixes: 3f14b73c38 ("ath10k: Enable MSA region dump support for WCN3990")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For all data packets transmitted, host gets htt tx completion event. Some QCA9984
firmware releases support WMI_SERVICE_TX_DATA_ACK_RSSI, which gives data
ack rssi values to host through htt event of data tx completion. Data ack rssi
values are valid if A0 bit is set in HTT rx message. So enable the feature also
for QCA9884.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00044
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[kvalo@codeaurora.org: improve commit log]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_TLV_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath10k will check the capability, and if it is enabled then
ath10k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath10k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware to enable/disable the radio
and also notifies cfg80211.
We can't power off the device when rfkill is enabled, as otherwise the
firmware would not be able to detect GPIO changes and report them to the
host. So when rfkill is enabled, we need to keep the firmware running.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch restores the old behavior that read
the chip_id on the QCA988x before resetting the
chip. This needs to be done in this order since
the unsupported QCA988x AR1A chips fall off the
bus when resetted. Otherwise the next MMIO Op
after the reset causes a BUS ERROR and panic.
Cc: stable@vger.kernel.org
Fixes: 1a7fecb766 ("ath10k: reset chip before reading chip_id in probe")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
