On TGL/RKL the BIOS likes to use some kind of bogus DBUF layout
that doesn't match what the spec recommends. With a single active
pipe that is not going to be a problem, but with multiple pipes
active skl_commit_modeset_enables() goes into an infinite loop
since it can't figure out any order in which it can commit the
pipes without causing DBUF overlaps between the planes.
We'd need some kind of extra DBUF defrag stage in between to
make the transition possible. But that is clearly way too complex
a solution, so in the name of simplicity let's just sanitize the
DBUF state by simply turning off all planes when we detect a
pipe encroaching on its neighbours' DBUF slices. We only have
to disable the primary planes as all other planes should have
already been disabled (if they somehow were enabled) by
earlier sanitization steps.
And for good measure let's also sanitize in case the DBUF
allocations of the pipes already seem to overlap each other.
Cc: <stable@vger.kernel.org> # v5.14+
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4762
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220204141818.1900-3-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
(cherry picked from commit 15512021eb)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Driver Changes:
- Added bits of DG2 support around page table handling (Stuart Summers, Matthew Auld)
- Fixed wakeref leak in PMU busyness during reset in GuC mode (Umesh Nerlige Ramappa)
- Fixed debugfs access crash if GuC failed to load (John Harrison)
- Bring back GuC error log to error capture, undoing accidental earlier breakage (Thomas Hellström)
- Fixed memory leak in error capture caused by earlier refactoring (Thomas Hellström)
- Exclude reserved stolen from driver use (Chris Wilson)
- Add memory region sanity checking and optional full test (Chris Wilson)
- Fixed buffer size truncation in TTM shmemfs backend (Robert Beckett)
- Use correct lock and don't overwrite internal data structures when stealing GuC context ids (Matthew Brost)
- Don't hog IRQs when destroying GuC contexts (John Harrison)
- Make GuC to Host communication more robust (Matthew Brost)
- Continuation of locking refactoring around VMA and backing store handling (Maarten Lankhorst)
- Improve performance of reading GuC log from debugfs (John Harrison)
- Log when GuC fails to reset an engine (John Harrison)
- Speed up GuC/HuC firmware loading by requesting RP0 (Vinay Belgaumkar)
- Further work on asynchronous VMA unbinding (Thomas Hellström, Christian König)
- Refactor GuC/HuC firmware handling to prepare for future platforms (John Harrison)
- Prepare for future different GuC/HuC firmware signing key sizes (Daniele Ceraolo Spurio, Michal Wajdeczko)
- Add noreclaim annotations (Matthew Auld)
- Remove racey GEM_BUG_ON between GPU reset and GuC communication handling (Matthew Brost)
- Refactor i915->gt with to_gt(i915) to prepare for future platforms (Michał Winiarski, Andi Shyti)
- Increase GuC log size for CONFIG_DEBUG_GEM (John Harrison)
- Fixed engine busyness in selftests when in GuC mode (Umesh Nerlige Ramappa)
- Make engine parking work with PREEMPT_RT (Sebastian Andrzej Siewior)
- Replace X86_FEATURE_PAT with pat_enabled() (Lucas De Marchi)
- Selftest for stealing of guc ids (Matthew Brost)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/YcRvKO5cyPvIxVCi@tursulin-mobl2
Use to_gt() helper consistently throughout the codebase.
Pure mechanical s/i915->gt/to_gt(i915). No functional changes.
Signed-off-by: Michał Winiarski <michal.winiarski@intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211214193346.21231-4-andi.shyti@linux.intel.com
drm/i915 feature pull #2 for v5.17:
Features and functionality:
- Add eDP privacy screen support (Hans)
- Add Raptor Lake S (RPL-S) support (Anusha)
- Add CD clock squashing support (Mika)
- Properly support ADL-P without force probe (Clint)
- Enable pipe color support (10 bit gamma) for display 13 platforms (Uma)
- Update ADL-P DMC firmware to v2.14 (Madhumitha)
Refactoring and cleanups:
- More FBC refactoring preparing for multiple FBC instances (Ville)
- Plane register cleanups (Ville)
- Header refactoring and include cleanups (Jani)
- Crtc helper and vblank wait function cleanups (Jani, Ville)
- Move pipe/transcoder/abox masks under intel_device_info.display (Ville)
Fixes:
- Add a delay to let eDP source OUI write take effect (Lyude)
- Use div32 version of MPLLB word clock for UHBR on SNPS PHY (Jani)
- Fix DMC firmware loader overflow check (Harshit Mogalapalli)
- Fully disable FBC on FIFO underruns (Ville)
- Disable FBC with double wide pipe as mutually exclusive (Ville)
- DG2 workarounds (Matt)
- Non-x86 build fixes (Siva)
- Fix HDR plane max width for NV12 (Vidya)
- Disable IRQ for selftest timestamp calculation (Anshuman)
- ADL-P VBT DDC pin mapping fix (Tejas)
Merges:
- Backmerge drm-next for privacy screen plumbing (Jani)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/87ee6f5h9u.fsf@intel.com
Add support for eDP panels with a built-in privacy screen using the
new drm_privacy_screen class.
Changes in v3:
- Move drm_privacy_screen_get() call to intel_ddi_init_dp_connector()
Changes in v2:
- Call drm_connector_update_privacy_screen() from
intel_enable_ddi_dp() / intel_ddi_update_pipe_dp() instead of adding a
for_each_new_connector_in_state() loop to intel_atomic_commit_tail()
- Move the probe-deferral check to the intel_modeset_probe_defer() helper
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005202322.700909-11-hdegoede@redhat.com
The upcoming privacy-screen support adds another check for
deferring probe till some other drivers have bound first.
Factor out the current vga_switcheroo_client_probe_defer() check
into an intel_modeset_probe_defer() helper, so that further
probe-deferral checks can be added there.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211005202322.700909-10-hdegoede@redhat.com
There's no need to store all this stuff in intel_fbc_state_cache.
Just check it all against the plane/crtc states and store only
what we need. Probably more should get nuked still, but this
is a start.
So what we'll do is:
- each plane will check its own state and update its local
no_fbc_reason
- the per-plane no_fbc_reason (if any) then gets propagated
to the cache->no_fbc_reason while doing the actual update
- fbc->no_fbc_reason gets updated in the end with either
the value from the cache or directly from frontbuffer
tracking
It's still a bit messy, but should hopefuly get cleaned up
more in the future. At least now we can observe each plane's
reasons for rejecting FBC now more consistently, and we don't
have so mcuh redundant state store all over the place.
v2: store no_fbc_reason per-plane instead of per-pipe
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211124113652.22090-4-ville.syrjala@linux.intel.com
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
This workaround is documented a bit strangely in the bspec; it's listed
as an A0 workaround, but the description clarifies that the workaround
is implicitly handled by the hardware and what the driver really needs
to do is program a chicken bit to reenable some internal behavior.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Clint Taylor <Clinton.A.Taylor@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211116174818.2128062-3-matthew.d.roper@intel.com
With both integrated and discrete Intel GPUs in a system, the current
global check of intel_iommu_gfx_mapped, as done from intel_vtd_active()
may not be completely accurate.
In this patch we add i915 parameter to intel_vtd_active() in order to
prepare it for multiple GPUs and we also change the check away from Intel
specific intel_iommu_gfx_mapped (global exported by the Intel IOMMU
driver) to probing the presence of IOMMU on a specific device using
device_iommu_mapped().
This will return true both for IOMMU pass-through and address translation
modes which matches the current behaviour. If in the future we wanted to
distinguish between these two modes we could either use
iommu_get_domain_for_dev() and check for __IOMMU_DOMAIN_PAGING bit
indicating address translation, or ask for a new API to be exported from
the IOMMU core code.
v2:
* Check for dmar translation specifically, not just iommu domain. (Baolu)
v3:
* Go back to plain "any domain" check for now, rewrite commit message.
v4:
* Use device_iommu_mapped. (Robin, Baolu)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Lu Baolu <baolu.lu@linux.intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Robin Murphy <robin.murphy@arm.com>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Reviewed-by: Lu Baolu <baolu.lu@linux.intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211126141424.493753-1-tvrtko.ursulin@linux.intel.com
Rather than stealing bits from i915_sw_fence function pointer use
separate fields for function pointer and flags. If using two different
fields, the 4 byte alignment for the i915_sw_fence function pointer can
also be dropped.
v2:
(CI)
- Set new function field rather than flags in __i915_sw_fence_init
v3:
(Tvrtko)
- Remove BUG_ON(!fence->flags) in reinit as that will now blow up
- Only define fence->flags if CONFIG_DRM_I915_SW_FENCE_CHECK_DAG is
defined
v4:
- Rebase, resend for CI
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Alan Previn <alan.previn.teres.alexis@intel.com>
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211116194929.10211-1-matthew.brost@intel.com
TileF(Tile4 in bspec) format is 4K tile organized into
64B subtiles with same basic shape as for legacy TileY
which will be supported by Display13.
v2: - Fixed wrong case condition(Jani Nikula)
- Increased I915_FORMAT_MOD_F_TILED up to 12(Imre Deak)
v3: - s/I915_TILING_F/TILING_4/g
- s/I915_FORMAT_MOD_F_TILED/I915_FORMAT_MOD_4_TILED/g
- Removed unneeded fencing code
v4: - Rebased, fixed merge conflict with new table-oriented
format modifier checking(Stan)
- Replaced the rest of "Tile F" mentions to "Tile 4"(Stan)
v5: - Still had to remove some Tile F mentionings
- Moved has_4tile from adlp to DG2(Ramalingam C)
- Check specifically for DG2, but not the Display13(Imre)
v6: - Moved Tile4 associating struct for modifier/display to
the beginning(Imre Deak)
- Removed unneeded case I915_FORMAT_MOD_4_TILED modifier
checks(Imre Deak)
- Fixed I915_FORMAT_MOD_4_TILED to be 9 instead of 12
(Imre Deak)
v7: - Fixed display_ver to { 13, 13 }(Imre Deak)
- Removed redundant newline(Imre Deak)
Reviewed-by: Imre Deak <imre.deak@intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Juha-Pekka Heikkilä <juha-pekka.heikkila@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211122211420.31584-1-stanislav.lisovskiy@intel.com
After a non-blocking modeset on a TypeC port's CRTC - possibly blocked
later in drm_atomic_helper_wait_for_dependencies() - a fastset on the
same CRTC may copy the state of CRTC before this gets updated to reflect
the up-to-date DP-alt vs. TBT-alt TypeC mode DPLL used for the CRTC. In
this case after the first (non-blocking) commit completes enabling the
DPLL required for the up-to-date TypeC mode the following fastset will
update the CRTC state pointing to the wrong DPLL. A subsequent disabling
modeset will try to disable the wrong PLL, triggering a state checker
WARN (and leaving the DPLL which is actually used active for good).
Fix the above race by copying the DPLL state for fastset CRTCs from the
old CRTC state at the point where it's guaranteed to be up-to-date
already. This could be handled in the encoder's update_prepare() hook as
well, but that's a bigger change, which is better done as a follow-up.
v2: Copy dpll_hw_state as well. (Ville)
Testcase: igt/kms_busy/extended-modeset-hang-newfb-with-reset
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/4308
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211115181121.156197-1-imre.deak@intel.com
With multiple fbc instances we need to find the right one for each
plane. Rather than going looking for the right instance every time
let's just replace the has_fbc boolean with a pointer that gets us
there straight away.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211104144520.22605-18-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
In preparation for multiple FBC instances start passing around
intel_fbc pointers rather than i915 pointers. And once there are
multiple of these we can't rely on container_of() to get back to
the i915, so we toss in a fbc->i915 pointer already.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211104144520.22605-17-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
The pipe gamma registers are single buffered so they should only
be updated during the vblank to avoid screen tearing. In fact they
really should only be updated between start of vblank and frame
start because that is the only time the pipe is guaranteed to be
empty. Already at frame start the pipe begins to fill up with
data for the next frame.
Unfortunately frame start happens ~1 scanline after the start
of vblank which in practice doesn't always leave us enough time to
finish the gamma update in time (gamma LUTs can be several KiB of
data we have to bash into the registers). However we must try our
best and so we'll add a vblank work for each pipe from where we
can do the gamma update. Additionally we could consider pushing
frame start forward to the max of ~4 scanlines after start of
vblank. But not sure that's exactly a validated configuration.
As it stands the ~100 first pixels tend to make it through with
the old gamma values.
Even though the vblank worker is running on a high prority thread
we still have to contend with C-states. If the CPU happens be in
a deep C-state when the vblank interrupt arrives even the irq
handler gets delayed massively (I've observed dozens of scanlines
worth of latency). To avoid that problem we'll use the qos mechanism
to keep the CPU awake while the vblank work is scheduled.
With all this hooked up we can finally enjoy near atomic gamma
updates. It even works across several pipes from the same atomic
commit which previously was a total fail because we did the
gamma updates for each pipe serially after waiting for all
pipes to have latched the double buffered registers.
In the future the DSB should take over this responsibility
which will hopefully avoid some of these issues.
Kudos to Lyude for finishing the actual vblank workers.
Works like the proverbial train toilet.
v2: Add missing intel_atomic_state fwd declaration
v3: Clean up properly when not scheduling the worker
v4: Clean up the rest and add tracepoints
v5: s/intel_wait_for_vblank_works/intel_wait_for_vblank_workers/ (Jani,Uma)
CC: Lyude Paul <lyude@redhat.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020223339.669-4-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
So far the remapped view size in GTT/DPT was padded to the next aligned
offset unnecessarily after the last color plane with an unaligned size.
Remove the unnecessary padding.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Fixes: 3d1adc3d64 ("drm/i915/adlp: Add support for remapping CCS FBs")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026225105.2783797-3-imre.deak@intel.com
(cherry picked from commit 6b6636e176)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
The amount of plane registers we have to write has been steadily
increasing, putting more pressure on the vblank evasion mechanism
and forcing us to increase its time budget. Let's try to take some
of the pressure off by splitting plane updates into two parts:
1) write all non-self arming plane registers, ie. the registers
where the write actually does nothing until a separate arming
register is also written which will cause the hardware to latch
the new register values at the next start of vblank
2) write all self arming plane registers, ie. registers which always
just latch at the next start of vblank, and registers which also
arm other registers to do so
Here we just provide the mechanism, but don't actually implement
the split on any platform yet. so everything stays now in the _arm()
hooks. Subsequently we can move a whole bunch of stuff into the
_noarm() part, especially in more modern platforms where the number
of registers we have to write is also the greatest. On older
platforms this is less beneficial probably, but no real reason
to deviate from a common behaviour.
And let's sprinkle some TODOs around the areas that will need
adapting.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018115030.3547-5-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Async flips are only capable of changing PLANE_SURF, hence we
they can't easily be used with planar formats.
Older platforms could require updating AUX_DIST as well, which
is not possible. We'd have to make sure AUX_DIST doesn't change
before allowing the async flip through. If we could get async
flips with CCS then that might be interesting, but since the hw
doesn't allow async flips with CCS I don't see much point in
allowing this for planar formats either. No one renders their
game content in YUV anyway.
icl+ could in theory do this I suppose since each color plane
has its own PLANE_SURF register, but I don't know if there is
some magic to guarantee that both the Y and UV plane would
async flip synchronously if you will. Ie. beyond just a clean
tear we'd potentially get some kind of weird tear with some
random mix of luma and chroma from the old and new frames.
So let's just say no to async flips when scanning out planar
formats.
Cc: Karthik B S <karthik.b.s@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018115030.3547-2-ville.syrjala@linux.intel.com
Reviewed-by: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
The next patch needs to distinguish between a view's mapping and scanout
stride. Rename the current stride parameter to mapping_stride with the
script below. mapping_stride will keep the same meaning as stride had
on all platforms so far, while the meaning of it will change on ADLP.
No functional changes.
@@
identifier intel_fb_view;
identifier i915_color_plane_view;
identifier color_plane;
expression e;
type T;
@@
struct intel_fb_view {
...
struct i915_color_plane_view {
...
- T stride;
+ T mapping_stride;
...
} color_plane[e];
...
};
@@
struct i915_color_plane_view pv;
@@
pv.
- stride
+ mapping_stride
@@
struct i915_color_plane_view *pvp;
@@
pvp->
- stride
+ mapping_stride
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026225105.2783797-6-imre.deak@intel.com
During remapping CCS FBs the CCS AUX surface mapped size and offset->x,y
coordinate calculations assumed a tiled layout. This works as long as
the CCS surface height is aligned to 64 lines (ensuring a 4k bytes CCS
surface tile layout). However this alignment is not required by the HW
(and the driver doesn't enforces it either).
Add the remapping logic required to remap the pages of CCS surfaces
without the above alignment, assuming the natural linear layout of the
CCS surface (vs. tiled main surface layout).
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: 3d1adc3d64 ("drm/i915/adlp: Add support for remapping CCS FBs")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026225105.2783797-5-imre.deak@intel.com
So far the remapped view size in GTT/DPT was padded to the next aligned
offset unnecessarily after the last color plane with an unaligned size.
Remove the unnecessary padding.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Fixes: 3d1adc3d64 ("drm/i915/adlp: Add support for remapping CCS FBs")
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211026225105.2783797-3-imre.deak@intel.com
For every crtc in state, intel_atomic_check_async() was checking all
the crtc and plane states again.
v2: comparing pipe ids instead of crtc pointers when iterating over
planes
Cc: Karthik B S <karthik.b.s@intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211029202432.140745-1-jose.souza@intel.com
Try to make bigjoiner pipes less special.
The main things here are that each pipe now does full
clock computation/readout with its own shared_dpll reference.
Also every pipe's cpu_transcoder always points correctly
at the master transcoder.
Due to the above changes state readout is now complete
and all the related hacks can go away. The actual modeset
sequence code is still a mess, but I think in order to clean
that up properly we're probably going to have to redesign
the modeset logic to treat transcoders vs. pipes separately.
That is going to require significant amounts of work.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-9-ville.syrjala@linux.intel.com
The PPS SDP is fed into the transcoder whereas the DSC
block is (or at least can be) per pipe. Let's split these
into two distinct operations in an effort to untagle the
bigjoiner mess where we have two pipes feeding a single
transcoder.
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-7-ville.syrjala@linux.intel.com
Let's disable planes on all pipes affected by the modeset before
we start doing the actual modeset. This means we have less
random planes enabled during the modeset, and it also mirrors
what we already do when enabling pipes on skl+ since we enable
planes on all pipes as the very last step. As a bonus we also
nuke a bunch og bigjoiner special casing.
I've occasionally pondered about going even furher here and
doing the pre_plane_update() stuff for all pipes first, then
actually disabling the planes, and finally running the rest
of the modeset sequence. This would potentially allow
parallelizing all the extra vblank waits across multiple pipes,
and would make the plane disable even more atomic. But let's
go one step a time here.
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Manasi Navare <manasi.d.navare@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-4-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Disabling planes in the middle of the modeset seuqnece does not make
sense since userspace can anyway disable planes before the modeset
even starts. So when the modeset seuqence starts the set of enabled
planes is entirely arbitrary. Trying to sprinkle the plane disabling
into the modeset sequence just means more randomness and potential
for hard to reproduce bugs.
So it makes most sense to just disable all planes first so that the
rest of the modeset sequence remains identical regardless of which
planes happen to be enabled by userspace at the time.
This reverts commit 84030adb9e.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-3-ville.syrjala@linux.intel.com
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
PSR2 apparently requires some planes to be enabled for some
silly reason, and so we are now trying to turn PSR off before
planes go off. Except during a full modeset that is handled
less clearly through reorganization of the modeset sequence.
That is not great as it makes the code mode complex, and
prevents us from doing nice things such as just turning off
all the planes at the very start of the modeset. So let's
move the PSR pre_plane_update() thing to a spot where it
will handle both full modesets and everything else.
Cc: José Roberto de Souza <jose.souza@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211022103304.24164-2-ville.syrjala@linux.intel.com
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
On future platforms the index of the color-clear plane will change from
the one used by the GEN12 RC CCS CC modifier, so add a way to retrieve
the index independently of the platform/modifier.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-8-imre.deak@intel.com
Move intel_format_info_is_yuv_semiplanar() to intel_fb.c . The number of
planes for YUV semiplanar formats using CCS modifiers will change on
future platforms. We can use the modifier descriptors to simplify
getting the plane numbers for all modifiers, prepare for that here.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-7-imre.deak@intel.com
Move the function retrieving the format override information for a given
format/modifier to intel_fb.c. We can store a pointer to the format list
in each modifier's descriptor instead of the corresponding switch/case
logic, avoiding the listing of the modifiers twice.
v1: Unchanged.
v2: Handle invalid modifiers in intel_fb_get_format_info() passed from
userspace. (CI/igt_kms_addfb_basic/addfb25-bad-modifier)
v3: Move lookup_modifier() to the next patch, where it's first used.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211020195138.1841242-3-imre.deak@intel.com
Hoover the remaining open coded PCH modeset sequence bits
out from ilk_crtc_disable(). Somewhat annoyingly the
enable vs. disable is a bit asymmetric so we need two
functions for the disable case.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-8-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Pull the ilk+ PCH state readout into its own function and relocate
to the appropriate file.
The clock readout parts are perhaps a bit iffy since we depend
on the gmch DPLL readout code. But we can think about the clock
readout big picture later.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211015071625.593-6-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
Nuke the hsw_get_ddi_port_state() eyesore by putting the
readout code into intel_pch_display.c, and calling it directly
from hsw_crt_get_config().
Note that the nuked TRANS_DDI_FUNC_CTL readout from
hsw_get_ddi_port_state() is now etirely redundant since we
get called from the encoder->get_config() so we already know
we're dealing with the correct DDI port. Previously the
code was called from a place where that wasn't known so
it had to checked manually.
v2: Clarify the TRANS_DDI_FUNC_CTL change (Dave)
Nuke the now unused *TRANS_DDI_FUNC_CTL_VAL_TO_PORT() (Dave)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20211018153525.21597-1-ville.syrjala@linux.intel.com
Reviewed-by: Dave Airlie <airlied@redhat.com>
