On bind we will register the HDMI codec device but we don't unregister
it on unbind, leading to a device leakage. Unregister our device at
unbind.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127111452.222002-1-maxime@cerno.tech
The 2711 pixel valve can't produce odd horizontal timings, and
checks were added to vc4_hdmi_encoder_atomic_check and
vc4_hdmi_encoder_mode_valid to filter out/block selection of
such modes.
Modes with DRM_MODE_FLAG_DBLCLK double all the horizontal timing
values before programming them into the PV. The PV values,
therefore, can not be odd, and so the modes can be supported.
Amend the filtering appropriately.
Fixes: 57fb32e632 ("drm/vc4: hdmi: Block odd horizontal timings")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127135116.298278-1-maxime@cerno.tech
The code that set the scdc_enabled flag to ensure it was
disabled at boot time also ran on Pi0-3 where there is no
SCDC support. This lead to a warning in vc4_hdmi_encoder_post_crtc_disable
due to vc4_hdmi_disable_scrambling being called and trying to
read (and write) register HDMI_SCRAMBLER_CTL which doesn't
exist on those platforms.
Only set the flag should the interface be configured to support
more than HDMI 1.4.
Fixes: 1998646129 ("drm/vc4: hdmi: Introduce a scdc_enabled flag")
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127134559.292778-1-maxime@cerno.tech
The existing logic was flawed in that it could try reading the
2711 specific registers for HPD on a CM1/3 where the HPD GPIO
hadn't been defined in DT.
Ensure we don't do the 2711 register read on invalid hardware,
and then
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20220127131754.236074-1-maxime@cerno.tech
We currently rely on two functions, vc4_hdmi_supports_scrambling() and
vc4_hdmi_mode_needs_scrambling() to determine if we should enable and
disable the scrambler for any given mode.
Since we might need to disable the controller at boot, we also always
run vc4_hdmi_disable_scrambling() and thus call those functions without
a mode yet, which in turns need to make some special casing in order for
it to work.
Instead of duplicating the check for whether or not we need to take care
of the scrambler in both vc4_hdmi_enable_scrambling() and
vc4_hdmi_disable_scrambling(), we can do that check only when we enable
it and store whether or not it's been enabled in our private structure.
We also need to initialize that flag at true to make sure we disable the
scrambler at boot since we can't really know its state yet.
This allows to simplify a bit that part of the driver, and removes one
user of our copy of the CRTC adjusted mode outside of KMS (since
vc4_hdmi_disable_scrambling() might be called from the hotplug interrupt
handler).
It also removes our last user of the legacy encoder->crtc pointer.
Link: https://lore.kernel.org/r/20211025141113.702757-10-maxime@cerno.tech
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
We currently poke at encoder->crtc in the ALSA code path to determine
whether the HDMI output is enabled or not, and thus whether we should
allow the audio output.
However, that pointer is deprecated and shouldn't really be used by
atomic drivers anymore. Since we have the infrastructure in place now,
let's just create a flag that we toggle to report whether the controller
is currently enabled and use that instead of encoder->crtc in ALSA.
Link: https://lore.kernel.org/r/20211025141113.702757-9-maxime@cerno.tech
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Even though we already check that the encoder->crtc pointer is there
during in startup(), which is part of the open() path in ASoC, nothing
guarantees that our encoder state won't change between the time when we
open the device and the time we prepare it.
Move the sanity checks we do in startup() to a helper and call it from
prepare().
Link: https://lore.kernel.org/r/20211025141113.702757-8-maxime@cerno.tech
Fixes: 91e99e1139 ("drm/vc4: hdmi: Register HDMI codec")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Accessing the crtc->state pointer from outside the modesetting context
is not allowed. We thus need to copy whatever we need from the KMS state
to our structure in order to access it.
However, in the vc4 HDMI driver we do use that pointer in the ALSA code
path, and potentially in the hotplug interrupt handler path.
These paths both need access to the CRTC adjusted mode in order for the
proper dividers to be set for ALSA, and the scrambler state to be
reinstated properly for hotplug.
Let's copy this mode into our private encoder structure and reference it
from there when needed. Since that part is shared between KMS and other
paths, we need to protect it using our mutex.
Link: https://lore.kernel.org/all/YWgteNaNeaS9uWDe@phenom.ffwll.local/
Link: https://lore.kernel.org/r/20211025141113.702757-7-maxime@cerno.tech
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4 HDMI controller registers into the KMS, CEC and ALSA
frameworks.
However, no particular care is done to prevent the concurrent execution
of different framework hooks from happening at the same time.
In order to protect against that scenario, let's introduce a mutex that
relevant ALSA and KMS hooks will need to take to prevent concurrent
execution.
CEC is left out at the moment though, since the .get_modes and .detect
KMS hooks, when running cec_s_phys_addr_from_edid, can end up calling
CEC's .adap_enable hook. This introduces some reentrancy that isn't easy
to deal with properly.
The CEC hooks also don't share much state with the rest of the driver:
the registers are entirely separate, we don't share any variable, the
only thing that can conflict is the CEC clock divider setup that can be
affected by a mode set.
However, after discussing it, it looks like CEC should be able to
recover from this if it was to happen.
Link: https://lore.kernel.org/r/20211025141113.702757-6-maxime@cerno.tech
Fixes: bb7d785688 ("drm/vc4: Add HDMI audio support")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
The vc4 HDMI driver has multiple path shared between the CEC, ALSA and
KMS frameworks, plus two interrupt handlers (CEC and hotplug) that will
read and modify a number of registers.
Even though not bug has been reported so far, it's definitely unsafe, so
let's just add a spinlock to protect the register access of the HDMI
controller.
Link: https://lore.kernel.org/r/20211025141113.702757-5-maxime@cerno.tech
Fixes: c8b75bca92 ("drm/vc4: Add KMS support for Raspberry Pi.")
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
If we have a state already and disconnect/reconnect the display, the
SCDC messages won't be sent again since we didn't go through a disable /
enable cycle.
In order to fix this, let's call the vc4_hdmi_enable_scrambling function
in the detect callback if there is a mode and it needs the scrambler to
be enabled.
Fixes: c85695a201 ("drm/vc4: hdmi: Enable the scrambler")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-10-maxime@cerno.tech
Now that we have the infrastructure in place, we can raise the maximum
pixel rate we can reach for HDMI0 on the BCM2711.
HDMI1 is left untouched since its pixelvalve has a smaller FIFO and
would need a clock faster than what we can provide to support the same
modes.
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20211025152903.1088803-9-maxime@cerno.tech
Prior to commit 6800234cee ("drm/vc4: hdmi: Convert to gpiod"), in the
detect hook, if we had an HPD GPIO we would only rely on it and return
whatever state it was in.
However, that commit changed that by mistake to only consider the case
where we have a GPIO and it returns a logical high, and would fall back
to the other methods otherwise.
Since we can read the EDIDs when the HPD signal is low on some displays,
we changed the detection status from disconnected to connected, and we
would ignore an HPD pulse.
Fixes: 6800234cee ("drm/vc4: hdmi: Convert to gpiod")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-3-maxime@cerno.tech
Commit 9d44abbbb8 ("drm/vc4: Fall back to using an EDID probe in the
absence of a GPIO.") added some code to read the EDID through DDC in the
HDMI driver detect hook since the Pi3 had no HPD GPIO back then.
However, commit b1b8f45b31 ("ARM: dts: bcm2837: Add missing GPIOs of
Expander") changed that a couple of years later.
This causes an issue though since some TV (like the LG 55C8) when it
comes out of standy will deassert the HPD line, but the EDID will
remain readable.
It causes an issues nn platforms without an HPD GPIO, like the Pi4,
where the DDC probing will be our primary mean to detect a display, and
thus we will never detect the HPD pulse. This was fine before since the
pulse was small enough that we would never detect it, and we also didn't
have anything (like the scrambler) that needed to be set up in the
display.
However, now that we have both, the display during the HPD pulse will
clear its scrambler status, and since we won't detect the
disconnect/reconnect cycle we will never enable the scrambler back.
As our main reason for that DDC probing is gone, let's just remove it.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://lore.kernel.org/r/20211025152903.1088803-2-maxime@cerno.tech
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmF298ceHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGIJYH/1rsEFQQ6caeQdy1
z9eFIe48DNM4l7bFk+qEj2UAbzPdahVJ299Mg5fW0n2CDemOc9/n0b9TxQ37YObi
mOzu0xwJVupIxkyFMPQSSc2q8aLm67NSpJy08DsmaNses5hSvu8x15RPHLQTybjt
SwtKns+jpCq79P1GWbrB5e5UkLb0VNoxNp4L1U4pMrYGcEkJUXbaxNY2V/JcXdM7
Vtn+qN0T/J6V6QVftv0t8Ecj3bjEnmL3kZHaTaNg3dGeKRpCGyHc5lcBQ0cNFG6t
vjZ9VbuhBzGI3TN2tHH5hpA1UXo7HPBBCwQqxF1jeGLGHULikYwZ3TAPWqL3QZqC
9cxr9SY=
=p75d
-----END PGP SIGNATURE-----
BackMerge tag 'v5.15-rc7' into drm-next
The msm next tree is based on rc3, so let's just backmerge rc7 before pulling it in.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Similarly to what we encountered with the detect hook with DRM, nothing
actually prevents any of the CEC callback from being run while the HDMI
output is disabled.
However, this is an issue since any register access to the controller
when it's powered down will result in a silent hang.
Let's make sure we run the runtime_pm hooks when the CEC adapter is
opened and closed by the userspace to avoid that issue.
Fixes: 15b4511a4a ("drm/vc4: add HDMI CEC support")
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819135931.895976-6-maxime@cerno.tech
In order to ease further additions to the CEC enable and disable, let's
split the function into two functions, one to enable and the other to
disable.
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819135931.895976-5-maxime@cerno.tech
Since our pre_crtc_configure hook returned void, we didn't implement a
goto-based error path handling, leading to errors like failing to put
back the device in pm_runtime in all the error paths, but also failing
to disable the pixel clock if clk_set_min_rate on the HSM clock fails.
Move to a goto-based implementation to have an easier consitency.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Link: https://patchwork.freedesktop.org/patch/msgid/20210819135931.895976-4-maxime@cerno.tech
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
In the bind hook, we actually need the device to have the HSM clock
running during the final part of the display initialisation where we
reset the controller and initialise the CEC component.
Failing to do so will result in a complete, silent, hang of the CPU.
Fixes: 411efa18e4 ("drm/vc4: hdmi: Move the HSM clock enable to runtime_pm")
Link: https://patchwork.freedesktop.org/patch/msgid/20210819135931.895976-3-maxime@cerno.tech
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
If the HPD GPIO is not available and drm_probe_ddc fails, we end up
reading the HDMI_HOTPLUG register, but the controller might be powered
off resulting in a CPU hang. Make sure we have the power domain and the
HSM clock powered during the detect cycle to prevent the hang from
happening.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-6-maxime@cerno.tech
In order to access the HDMI controller, we need to make sure the HSM
clock is enabled. If we were to access it with the clock disabled, the
CPU would completely hang, resulting in an hard crash.
Since we have different code path that would require it, let's move that
clock enable / disable to runtime_pm that will take care of the
reference counting for us.
Since we also want to change the HSM clock rate and it's only valid
while the clock is disabled, we need to move the clk_set_min_rate() call
on the HSM clock above pm_runtime_get_and_sync().
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-5-maxime@cerno.tech
Link: https://lore.kernel.org/linux-arm-kernel/20210924152334.1342630-1-maxime@cerno.tech/
When the firmware doesn't setup the HSM rate (such as when booting
without an HDMI cable plugged in), its rate is 0 and thus any register
access results in a CPU stall, even though HSM is enabled.
Let's enforce a minimum rate at boot to avoid this issue.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Tested-by: Michael Stapelberg <michael@stapelberg.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20210922125419.4125779-4-maxime@cerno.tech
UAPI Changes:
- Allow empty drm leases for creating separate GEM namespaces.
Cross-subsystem Changes:
- Slightly rework dma_buf_poll.
- Add dma_resv_for_each_fence_unlocked to iterate, and use it inside
the lockless dma-resv functions.
Core Changes:
- Allow devm_drm_of_get_bridge to build without CONFIG_OF for compile testing.
- Add more DP2 headers.
- fix CONFIG_FB dependency in fb_helper.
- Add DRM_FORMAT_R8 to drm_format_info, and helpers for RGB332 and RGB888.
- Fix crash on a 0 or invalid EDID.
Driver Changes:
- Apply and revert DRM_MODESET_LOCK_ALL_BEGIN.
- Add mode_valid to ti-sn65dsi86 bridge.
- Support multiple syncobjs in v3d.
- Add R8, RGB332 and RGB888 pixel formats to GUD.
- Use devm_add_action_or_reset in dw-hdmi-cec.
-----BEGIN PGP SIGNATURE-----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=qxpr
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-10-06' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.16:
UAPI Changes:
- Allow empty drm leases for creating separate GEM namespaces.
Cross-subsystem Changes:
- Slightly rework dma_buf_poll.
- Add dma_resv_for_each_fence_unlocked to iterate, and use it inside
the lockless dma-resv functions.
Core Changes:
- Allow devm_drm_of_get_bridge to build without CONFIG_OF for compile testing.
- Add more DP2 headers.
- fix CONFIG_FB dependency in fb_helper.
- Add DRM_FORMAT_R8 to drm_format_info, and helpers for RGB332 and RGB888.
- Fix crash on a 0 or invalid EDID.
Driver Changes:
- Apply and revert DRM_MODESET_LOCK_ALL_BEGIN.
- Add mode_valid to ti-sn65dsi86 bridge.
- Support multiple syncobjs in v3d.
- Add R8, RGB332 and RGB888 pixel formats to GUD.
- Use devm_add_action_or_reset in dw-hdmi-cec.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Wed 06 Oct 2021 20:48:12 AEST
# gpg: using RSA key B97BD6A80CAC4981091AE547FE558C72A67013C3
# gpg: Good signature from "Maarten Lankhorst <maarten.lankhorst@linux.intel.com>" [expired]
# gpg: aka "Maarten Lankhorst <maarten@debian.org>" [expired]
# gpg: aka "Maarten Lankhorst <maarten.lankhorst@canonical.com>" [expired]
# gpg: Note: This key has expired!
# Primary key fingerprint: B97B D6A8 0CAC 4981 091A E547 FE55 8C72 A670 13C3
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/2602f4e9-a8ac-83f8-6c2a-39fd9ca2e1ba@linux.intel.com
Commitc7d30623540b ("drm/vc4: hdmi: Remove unused struct") removed the
references to the vc4_hdmi_audio_widgets and vc4_hdmi_audio_routes
structures, but not the structures themselves resulting in two warnings.
Remove it.
Fixes: c7d3062354 ("drm/vc4: hdmi: Remove unused struct")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819140753.930751-1-maxime@cerno.tech
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
The drm_helper_hpd_irq_event() documentation states that this function
is "useful for drivers which can't or don't track hotplug interrupts for
each connector." and that "Drivers which support hotplug interrupts for
each connector individually and which have a more fine-grained detect
logic should bypass this code and directly call
drm_kms_helper_hotplug_event()". This is thus what we ended-up doing.
However, what this actually means, and is further explained in the
drm_kms_helper_hotplug_event() documentation, is that
drm_kms_helper_hotplug_event() should be called by drivers that can
track the connection status change, and if it has changed we should call
that function.
This underlying expectation we failed to provide is that the caller of
drm_kms_helper_hotplug_event() should call drm_helper_probe_detect() to
probe the new status of the connector.
Since we didn't do it, it meant that even though we were sending the
notification to user-space and the DRM clients that something changed we
never probed or updated our internal connector status ourselves.
This went mostly unnoticed since the detect callback usually doesn't
have any side-effect. Also, if we were using the DRM fbdev emulation
(which is a DRM client), or any user-space application that can deal
with hotplug events, chances are they would react to the hotplug event
by probing the connector status eventually.
However, now that we have to enable the scrambler in detect() if it was
enabled it has a side effect, and an application such as Kodi or
modetest doesn't deal with hotplug events. This resulted with a black
screen when Kodi or modetest was running when a screen was disconnected
and then reconnected, or switched off and on.
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914101724.266570-3-maxime@cerno.tech
This reverts commits
9984d6664c ("drm/vc4: hdmi: Make sure the controller is powered in detect")
411efa18e4 ("drm/vc4: hdmi: Move the HSM clock enable to runtime_pm")
as Michael Stapelberg reports that the new runtime PM changes cause his
Raspberry Pi 3 to hang on boot, probably due to interactions with other
changes in the DRM tree (because a bisect points to the merge in commit
e058a84bfd: "Merge tag 'drm-next-2021-07-01' of git://.../drm").
Revert these two commits until it's been resolved.
Link: https://lore.kernel.org/all/871r5mp7h2.fsf@midna.i-did-not-set--mail-host-address--so-tickle-me/
Reported-and-tested-by: Michael Stapelberg <michael@stapelberg.ch>
Cc: Maxime Ripard <maxime@cerno.tech>
Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This symbol is not used outside of vc4_hdmi.c, so marks it static.
Fix the following sparse warning:
drivers/gpu/drm/vc4/vc4_hdmi.c:1479:25: warning: symbol
'vc4_hdmi_codec_pdata' was not declared. Should it be static?
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/1627640794-15718-1-git-send-email-jiapeng.chong@linux.alibaba.com
Commit 91e99e1139 ("drm/vc4: hdmi: Register HDMI codec") removed the
references to the vc4_hdmi_audio_component_drv structure, but not the
structure itself resulting in a warning. Remove it.
Fixes: 91e99e1139 ("drm/vc4: hdmi: Register HDMI codec")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707093632.1468127-2-maxime@cerno.tech
The vc4_hdmi_audio_prepare function and the functions it's calling have
in several occurences multiple dereferences of either the sample rate or
the number of channels.
It turns out that these variables are also passed through the hdmi codec
parameters structure. Convert all the users to use this structure, and
if it's used multiple times use a variable to store it instead of
dereferencing it every time.
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707093632.1468127-1-maxime@cerno.tech
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmD95yIeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGqp0H/j/xHL20EHaUJOaV
iJjnfGyjtnkLC5FCoV/q/v9sFuSW2p4W1nyF8/eIgVKObef94Mg4/xxaHQrWIM56
cbzK9aIcD9InAuImJ6lju4fqjNmFrt2x7mhfzjPKqmhfINfZ5CohpLFN5XdOwzYC
l+ZgmUUl7GLDAND2M6rtkc7AOk4qTyAySDvvPFELE/uNgV4EKaENSIWofHhEzW5v
Yk+4agawaFTfa6H9+uMVYZBOcEKwheQ0E2tcOJvHJT8Mwm8MFoC/B7fLY5zxIdN2
7A7r/7qbSQmSDSjOgwKS4ZOjom0xGSD+V+596SzET6jkbahR2HJ/mrFvmD7GNEoW
OWJPjzI=
=vzIM
-----END PGP SIGNATURE-----
Backmerge tag 'v5.14-rc3' into drm-next
Linux 5.14-rc3
Daniel said we should pull the nouveau fix from fixes in here, probably
a good plan.
Signed-off-by: Dave Airlie <airlied@redhat.com>
UAPI Changes:
Cross-subsystem Changes:
- udmabuf: Add support for mapping hugepages
- Add dma-buf stats to sysfs.
- Assorted fixes to fbdev/omap2.
- dma-buf: Document DMA_BUF_IOCTL_SYNC
- Improve dma-buf non-dynamic exporter expectations better.
- Add module parameters for dma-buf size and list limit.
- Add HDMI codec support to vc4, to replace vc4's own codec.
- Document dma-buf implicit fencing rules.
- dma_resv_test_signaled test_all handling.
Core Changes:
- Extract i915's eDP backlight code into DRM helpers.
- Assorted docbook updates.
- Rework drm_dp_aux documentation.
- Add support for the DP aux bus.
- Shrink dma-fence-chain slightly.
- Add alloc/free helpers for dma-fence-chain.
- Assorted fixes to TTM., drm/of, bridge
- drm_gem_plane_helper_prepare/cleanup_fb is now the default for gem drivers.
- Small fix for scheduler completion.
- Remove use of drm_device.irq_enabled.
- Print the driver name to dmesg when registering framebuffer.
- Export drm/gem's shadow plane handling, and use it in vkms.
- Assorted small fixes.
Driver Changes:
- Add eDP backlight to nouveau.
- Assorted fixes and cleanups to nouveau, panfrost, vmwgfx, anx7625,
amdgpu, gma500, radeon, mgag200, vgem, vc4, vkms, omapdrm.
- Add support for Samsung DB7430, Samsung ATNA33XC20, EDT ETMV570G2DHU,
EDT ETM0350G0DH6, Innolux EJ030NA panels.
- Fix some simple pannels missing bus_format and connector types.
- Add mks-guest-stats instrumentation support to vmwgfx.
- Merge i915-ttm topic branch.
- Make s6e63m0 panel use Mipi-DBI helpers.
- Add detect() supoprt for AST.
- Use interrupts for hotplug on vc4.
- vmwgfx is now moved to drm-misc-next, as sroland is no longer a maintainer for now.
- vmwgfx now uses copies of vmware's internal device headers.
- Slowly convert ti-sn65dsi83 over to atomic.
- Rework amdgpu dma-resv handling.
- Fix virtio fencing for planes.
- Ensure amdgpu can always evict to SYSTEM.
- Many drivers fixed for implicit fencing rules.
- Set default prepare/cleanup fb for tiny, vram and simple helpers too.
- Rework panfrost gpu reset and related serialization.
- Update VKMS todo list.
- Make bochs a tiny gpu driver, and use vram helper.
- Use linux irq interfaces instead of drm_irq in some drivers.
- Add support for Raspberry Pi Pico to GUD.
-----BEGIN PGP SIGNATURE-----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=x8Eo
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-2021-07-16' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
drm-misc-next for v5.15:
UAPI Changes:
Cross-subsystem Changes:
- udmabuf: Add support for mapping hugepages
- Add dma-buf stats to sysfs.
- Assorted fixes to fbdev/omap2.
- dma-buf: Document DMA_BUF_IOCTL_SYNC
- Improve dma-buf non-dynamic exporter expectations better.
- Add module parameters for dma-buf size and list limit.
- Add HDMI codec support to vc4, to replace vc4's own codec.
- Document dma-buf implicit fencing rules.
- dma_resv_test_signaled test_all handling.
Core Changes:
- Extract i915's eDP backlight code into DRM helpers.
- Assorted docbook updates.
- Rework drm_dp_aux documentation.
- Add support for the DP aux bus.
- Shrink dma-fence-chain slightly.
- Add alloc/free helpers for dma-fence-chain.
- Assorted fixes to TTM., drm/of, bridge
- drm_gem_plane_helper_prepare/cleanup_fb is now the default for gem drivers.
- Small fix for scheduler completion.
- Remove use of drm_device.irq_enabled.
- Print the driver name to dmesg when registering framebuffer.
- Export drm/gem's shadow plane handling, and use it in vkms.
- Assorted small fixes.
Driver Changes:
- Add eDP backlight to nouveau.
- Assorted fixes and cleanups to nouveau, panfrost, vmwgfx, anx7625,
amdgpu, gma500, radeon, mgag200, vgem, vc4, vkms, omapdrm.
- Add support for Samsung DB7430, Samsung ATNA33XC20, EDT ETMV570G2DHU,
EDT ETM0350G0DH6, Innolux EJ030NA panels.
- Fix some simple pannels missing bus_format and connector types.
- Add mks-guest-stats instrumentation support to vmwgfx.
- Merge i915-ttm topic branch.
- Make s6e63m0 panel use Mipi-DBI helpers.
- Add detect() supoprt for AST.
- Use interrupts for hotplug on vc4.
- vmwgfx is now moved to drm-misc-next, as sroland is no longer a maintainer for now.
- vmwgfx now uses copies of vmware's internal device headers.
- Slowly convert ti-sn65dsi83 over to atomic.
- Rework amdgpu dma-resv handling.
- Fix virtio fencing for planes.
- Ensure amdgpu can always evict to SYSTEM.
- Many drivers fixed for implicit fencing rules.
- Set default prepare/cleanup fb for tiny, vram and simple helpers too.
- Rework panfrost gpu reset and related serialization.
- Update VKMS todo list.
- Make bochs a tiny gpu driver, and use vram helper.
- Use linux irq interfaces instead of drm_irq in some drivers.
- Add support for Raspberry Pi Pico to GUD.
Signed-off-by: Dave Airlie <airlied@redhat.com>
# gpg: Signature made Fri 16 Jul 2021 21:06:04 AEST
# gpg: using RSA key B97BD6A80CAC4981091AE547FE558C72A67013C3
# gpg: Good signature from "Maarten Lankhorst <maarten.lankhorst@linux.intel.com>" [expired]
# gpg: aka "Maarten Lankhorst <maarten@debian.org>" [expired]
# gpg: aka "Maarten Lankhorst <maarten.lankhorst@canonical.com>" [expired]
# gpg: Note: This key has expired!
# Primary key fingerprint: B97B D6A8 0CAC 4981 091A E547 FE55 8C72 A670 13C3
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/444811c3-cbec-e9d5-9a6b-9632eda7962a@linux.intel.com
Our hotplug handler will currently call the drm_kms_helper_hotplug_event
every time a hotplug interrupt is called.
However, since the device is registered after all the drivers have
finished their bind callback, we have a window between when we install
our interrupt handler and when drm_dev_register() is eventually called
where our handler can run and call drm_kms_helper_hotplug_event but the
device hasn't been registered yet, causing a null pointer dereference.
Fix this by making sure we only call drm_kms_helper_hotplug_event if our
device has been properly registered.
Fixes: f4790083c7 ("drm/vc4: hdmi: Rely on interrupts to handle hotplug")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707095112.1469670-4-maxime@cerno.tech
The hotplugs interrupt handlers are registered through the
devm_request_threaded_irq function. However, while free_irq is indeed
called properly when the device is unbound or bind fails, it's called
after unbind or bind is done.
In our particular case, it means that on failure it creates a window
where our interrupt handler can be called, but we're freeing every
resource (CEC adapter, DRM objects, etc.) it might need.
In order to address this, let's switch to the non-devm variant to
control better when the handler will be unregistered and allow us to
make it safe.
Fixes: f4790083c7 ("drm/vc4: hdmi: Rely on interrupts to handle hotplug")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707095112.1469670-3-maxime@cerno.tech
The CEC interrupt handlers are registered through the
devm_request_threaded_irq function. However, while free_irq is indeed
called properly when the device is unbound or bind fails, it's called
after unbind or bind is done.
In our particular case, it means that on failure it creates a window
where our interrupt handler can be called, but we're freeing every
resource (CEC adapter, DRM objects, etc.) it might need.
In order to address this, let's switch to the non-devm variant to
control better when the handler will be unregistered and allow us to
make it safe.
Fixes: 15b4511a4a ("drm/vc4: add HDMI CEC support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210707095112.1469670-2-maxime@cerno.tech
Adjust the DVP enable/disable sequence to avoid a pixel getting stuck
in an internal, non resettable FIFO within PixelValve when changing
HDMI resolution.
The blank pixels features of the DVP can prevent signals back to
pixelvalve causing it to not clear the FIFO. Adjust the ordering
and timing of operations to ensure the clear signal makes it through to
pixelvalve.
Signed-off-by: Tim Gover <tim.gover@raspberrypi.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210628130533.144617-1-maxime@cerno.tech
We don't want to print an error message each time
devm_snd_soc_register_card() returns -EPROBE_DEFER, the function will
most likely succeed some time in the future, once the missing resources
are available. So use dev_err_probe(), which will redirect the messages
to the debug log level in such case.
Signed-off-by: Nicolas Saenz Julienne <nsaenzju@redhat.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210629121723.11523-1-nsaenzju@redhat.com
This was a workaround for bugs in hardware on earlier Pi models
and wasn't totally successful.
It makes audio quality worse on a Pi4 at the higher sample rates
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525132354.297468-10-maxime@cerno.tech
Without this bit set, HDMI_MAI_FORMAT doesn't pick up
the format and samplerate from DVP_CFG_MAI0_FMT and you
can't get HDMI_HDMI_13_AUDIO_STATUS_1 to indicate HBR mode
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525132354.297468-9-maxime@cerno.tech
The hardware uses this for generating the right audio
data island packets when using formats other than PCM
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525132354.297468-8-maxime@cerno.tech
Symptom is random switching of speakers when using multichannel.
Repeatedly running speakertest -c8 occasionally starts with
channels jumbled. This is fixed with HD_CTL_WHOLSMP.
The other bit looks beneficial and apears harmless in testing so
I'd suggest adding it too.
Documentation says: HD_CTL_WHILSMP_SET
Wait for whole sample. When this bit is set MAI transmit will start
only when there is at least one whole sample available in the fifo.
Documentation says: HD_CTL_CHALIGN_SET
Channel Align When Overflow. This bit is used to realign the audio
channels in case of an overflow.
If this bit is set, after the detection of an overflow, equal
amount of dummy words to the missing words will be written to fifo,
filling up the broken sample and maintaining alignment.
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525132354.297468-7-maxime@cerno.tech
If the HPD GPIO is not available and drm_probe_ddc fails, we end up
reading the HDMI_HOTPLUG register, but the controller might be powered
off resulting in a CPU hang. Make sure we have the power domain and the
HSM clock powered during the detect cycle to prevent the hang from
happening.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525091059.234116-4-maxime@cerno.tech
In order to access the HDMI controller, we need to make sure the HSM
clock is enabled. If we were to access it with the clock disabled, the
CPU would completely hang, resulting in an hard crash.
Since we have different code path that would require it, let's move that
clock enable / disable to runtime_pm that will take care of the
reference counting for us.
Fixes: 4f6e3d66ac ("drm/vc4: Add runtime PM support to the HDMI encoder driver")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210525091059.234116-3-maxime@cerno.tech
DRM currently polls for the HDMI connector status every 10s, which can
be an issue when we connect/disconnect a display quickly or the device
on the other end only issues a hotplug pulse (for example on EDID
change).
Switch the driver to rely on the internal controller logic for the
BCM2711/RPi4.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210524132018.264396-1-maxime@cerno.tech
The new gpiod interface takes care of parsing the GPIO flags and to
return the logical value when accessing an active-low GPIO, so switching
to it simplifies a lot the driver.
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210524131852.263883-2-maxime@cerno.tech
If the of_get_named_gpio_flags call fails in vc4_hdmi_bind, we jump to
the err_unprepare_hsm label. That label will then call
pm_runtime_disable and put_device on the DDC device.
We just retrieved the DDC device, so the latter is definitely justified.
However at that point we still haven't called pm_runtime_enable, so the
call to pm_runtime_disable is not supposed to be there.
Fixes: 10ee275cb1 ("drm/vc4: prepare for CEC support")
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20210524131852.263883-1-maxime@cerno.tech
