HTT_T2H_MSG_TYPE_PPDU_STATS_IND is a message which include the ppdu
info, currently it is not report from firmware for ath11k, then the
tx bitrate of "iw wlan0 station dump" always show an invalid value
"tx bitrate: 6.0 MBit/s".
To address the issue, this is to parse the info of tx complete report
from firmware and indicate the tx rate to mac80211.
After that, "iw wlan0 station dump" show the correct tx bit rate such
as:
tx bitrate: 78.0 MBit/s MCS 12
tx bitrate: 144.4 MBit/s VHT-MCS 7 short GI VHT-NSS 2
tx bitrate: 286.7 MBit/s HE-MCS 11 HE-NSS 2 HE-GI 0 HE-DCM 0
tx bitrate: 1921.5 MBit/s 160MHz HE-MCS 9 HE-NSS 2 HE-GI 0 HE-DCM 0
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/20211217093722.5739-1-quic_wgong@quicinc.com
A new hw_param full_monitor_mode is added to enable full
monitor support for QCN9074.
HTT_H2T_MSG_TYPE_RX_FULL_MONITOR_MODE cmd is sent to FW
to enable the full monitor mode.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com>
Link: https://lore.kernel.org/r/1638881695-22155-2-git-send-email-akolli@codeaurora.org
The pdev id is set to 0 for single pdev configured hardware, the real
pdev id is not 0 in firmware, for example, its pdev id is 1 for 5G/6G
phy and 2 for 2G band phy. For HTT_H2T_MSG_TYPE_EXT_STATS_CFG message,
firmware parse the pdev_mask to its pdev id, ath11k set it to 0 for
single pdev, it is not correct, need set it with the real pdev id of
firmware.
Save the real pdev id report by firmware and set it correctly.
Below commands run success with this patch:
cat /sys/kernel/debug/ieee80211/phy0/ath11k/htt_stats
cat /sys/kernel/debug/ieee80211/phy0/netdev\:wls1/stations/00\:03\:7f\:75\:59\:85/htt_peer_stats
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Wen Gong <quic_wgong@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211118095700.8149-1-quic_wgong@quicinc.com
Avoid unnecessary idr_find calls before the idr_remove calls. Because
idr_remove gives the valid ptr if id is valid otherwise return NULL ptr.
So removed the idr_find before idr_remove in tx completion path. Also no
need to disable the bottom half preempt if it is already in the
bottom half context, so modify the spin_lock_bh to spin_lock in the
data tx completion path.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-13-git-send-email-ppranees@codeaurora.org
Add branch prediction in dp_tx code path in tx and tx completion handlers.
Also in ath11k_dp_tx_complete_msdu , the pointer that is returned by
rcu_dereference() is not dereferenced. so it is preferable to use
rcu_access_pointer() here.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01734-QCAHKSWPL_SILICONZ-1 v2
Co-developed-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1630560820-21905-12-git-send-email-ppranees@codeaurora.org
HTT_PPDU_STATS_CFG_PDEV_ID bit mask for target FW PPDU stats request message
was set as bit 8 to 15. Bit 8 is reserved for soc stats and pdev id starts from
bit 9. Hence change the bitmask as bit 9 to 15 and fill the proper pdev id in
the request message.
In commit 701e48a43e ("ath11k: add packet log support for QCA6390"), both
HTT_PPDU_STATS_CFG_PDEV_ID and pdev_mask were changed, but this pdev_mask
calculation is not valid for platforms which has multiple pdevs with 1 rxdma
per pdev, as this is writing same value(i.e. 2) for all pdevs. Hence fixed it
to consider pdev_idx as well, to make it compatible for both single and multi
pd cases.
Tested on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01092-QCAHKSWPL_SILICONZ-1
Tested on: IPQ6018 hw1.0 WLAN.HK.2.5.0.1-01067-QCAHKSWPL_SILICONZ-1
Fixes: 701e48a43e ("ath11k: add packet log support for QCA6390")
Co-developed-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Rameshkumar Sundaram <ramess@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-10-jouni@codeaurora.org
Some targets, QCA6390 for example, use only one TCL ring, it is better to
initialize only one ring and leave others untouched for such targets.
This is a theoretical fix found during code review, no visible impact.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Baochen Qiang <bqiang@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210914163726.38604-1-jouni@codeaurora.org
In scenario when a peer is disassociating, there could be
multiple places where a reo cmd ring is accessed, such as
during aggregation teardown, tid queue cleanup, etc.
When this happens during firmware recovery where accessing of FW/HW
resources/registers is not recommended, accessing reo cmd ring in
this case could lead to crash or undefined behaviour.
Hence avoid this by checking for corresponding flag to avoid
accessing reo cmd ring during firmware recovery.
Sample crash:
[ 3936.456050] Unhandled fault: imprecise external abort (0x1c06) at 0x54bb842a
[ 3936.456411] WARN: Access Violation!!!, Run "cat /sys/kernel/debug/qcom_debug_logs/tz_log" for more details
[ 3936.467997] pgd = b4474000
[ 3936.477440] [54bb842a] *pgd=6fa61831, *pte=7f95d59f, *ppte=7f95de7e
<snip>
[ 3937.177436] [<8030ab10>] (_raw_spin_unlock_bh) from [<7f5e9eb8>] (ath11k_hal_reo_cmd_send+0x440/0x458 [ath11k])
[ 3937.185730] [<7f5e9eb8>] (ath11k_hal_reo_cmd_send [ath11k]) from [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd+0x2c/0xcc [ath11k])
[ 3937.195524] [<7f601c4c>] (ath11k_dp_tx_send_reo_cmd [ath11k]) from [<7f602f10>] (ath11k_peer_rx_tid_reo_update+0x84/0xbc [ath11k])
[ 3937.206984] [<7f602f10>] (ath11k_peer_rx_tid_reo_update [ath11k]) from [<7f605a9c>] (ath11k_dp_rx_ampdu_stop+0xa8/0x130 [ath11k])
[ 3937.218532] [<7f605a9c>] (ath11k_dp_rx_ampdu_stop [ath11k]) from [<7f5f6730>] (ath11k_mac_op_ampdu_action+0x6c/0x98 [ath11k])
[ 3937.230250] [<7f5f6730>] (ath11k_mac_op_ampdu_action [ath11k]) from [<c7b6e890>] (___ieee80211_stop_rx_ba_session+0x98/0x144 [mac80211])
[ 3937.241499] [<c7b6e890>] (___ieee80211_stop_rx_ba_session [mac80211]) from [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions+0x4c/0xf4 [)
[ 3937.253833] [<c7b6cdd8>] (ieee80211_sta_tear_down_BA_sessions [mac80211]) from [<c7b63460>] (ieee80211_sta_eosp+0x5b8/0x960 [mac80211])
[ 3937.266764] [<c7b63460>] (ieee80211_sta_eosp [mac80211]) from [<c7b66da8>] (__sta_info_flush+0x9c/0x134 [mac80211])
[ 3937.278826] [<c7b66da8>] (__sta_info_flush [mac80211]) from [<c7b7bd00>] (ieee80211_stop_ap+0x14c/0x28c [mac80211])
[ 3937.289240] [<c7b7bd00>] (ieee80211_stop_ap [mac80211]) from [<7f509cf0>] (__cfg80211_stop_ap+0x4c/0xd8 [cfg80211])
[ 3937.299629] [<7f509cf0>] (__cfg80211_stop_ap [cfg80211]) from [<7f4dddec>] (cfg80211_leave+0x24/0x30 [cfg80211])
[ 3937.310041] [<7f4dddec>] (cfg80211_leave [cfg80211]) from [<7f4de03c>] (cfg80211_netdev_notifier_call+0x174/0x48c [cfg80211])
[ 3937.320457] [<7f4de03c>] (cfg80211_netdev_notifier_call [cfg80211]) from [<80339928>] (notifier_call_chain+0x40/0x68)
[ 3937.331636] [<80339928>] (notifier_call_chain) from [<803399a8>] (raw_notifier_call_chain+0x14/0x1c)
[ 3937.342221] [<803399a8>] (raw_notifier_call_chain) from [<8073bb00>] (call_netdevice_notifiers+0xc/0x14)
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01240-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721212029.142388-7-jouni@codeaurora.org
If monitor interface is enabled in co-exist mode, only local traffic are
captured. It's caused by missing monitor vdev in co-exist mode. So,
monitor mode clean up is done with separate Monitor APIs. For this,
introduce flags monitor_started and monitor_vdev_created.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01725-QCAHKSWPL_SILICONZ-1
Co-developed-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Co-developed-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Seevalamuthu Mariappan <seevalam@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210721162053.46290-4-jouni@codeaurora.org
In 4addr, AP wired backbone to STA wired backbone ping fails due to ARP
request not getting answered. Here 4addr ARP multicast packet is sent in
3addr, so that 4addr STA not honouring the 3addr ARP multicast packet.
Fix this issue by sending out multicast packet in 4addr format, firmware
expects peer meta flag instead of vdev meta flag in Tx descriptor.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01641-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Jouni Malinen <jouni@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210720213147.90042-2-jouni@codeaurora.org
Update the specific hw ring mask for QCN9074. Update the timestamp
information while processing DP and CE interrupts.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-11-git-send-email-akolli@codeaurora.org
Define the hal ring address and ring meta descriptor mask for
QCN9074. Move the platform specific address to the ath11k_hw_regs.
Define tx_mesh_enable ops in ath11k_hw_ops since its accessing
platform specific TCL descriptor.
Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.4.0.1.r2-00012-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612946530-28504-8-git-send-email-akolli@codeaurora.org
Tx descriptor search index field should be updated with hw peer id
and not by AST Hash as per the HW/FW recommendation. Incorrect search
index causes throughput degradation in all scenario for all the
platforms. so updated the search index field with hw peer id, which
is a common change applicable for all the platforms. Also no need of these
configuration for non station type. seen 10% throughput increase in WDS
traffic with this change.
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-01492-QCAHKSWPL_SILICONZ-1
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1612410960-9120-1-git-send-email-periyasa@codeaurora.org
The driver_data area of ieee80211_tx_info is used in ath11k for
ath11k_skb_cb. The first function in the TX patch which rewrites it to
ath11k_skb_cb is already ath11k_mac_op_tx. No one else in the code path
must use it for something else before it reinitializes it. Otherwise the
data has to be considered uninitialized or corrupt.
But the ieee80211_tx_info.control shares exactly the same area as
ieee80211_tx_info.driver_data and ath11k is still using it. This results in
best case in a
ath11k c000000.wifi1: no vif found for mgmt frame, flags 0x0
or (slightly worse) in a kernel oops.
Instead, the interesting data must be moved first into the ath11k_skb_cb
and ieee80211_tx_info.control must then not be used anymore.
Tested-on: IPQ8074 hw2.0 WLAN.HK.2.4.0.1.r1-00026-QCAHKSWPL_SILICONZ-2
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20201119154235.263250-1-sven@narfation.org
Current ring selector logic follows round-robin scheduling,
when a process switch from one processor to another each time,
the data in the cache would have to be invalidated
and re-loaded from RAM leads to poor cache utilization.
Therefore smp_processor_id() attempt to keep processes
on the same processor via processor affinity which improves
cache utilization. Also, ring selection could be chosen round
robin when the processor_id based ring selection does not
have the resources.
Tested-on : IPQ8074 hw2.0 AHB WLAN.HK.2.4.0.1-00874-QCAHKSWPL_SILICONZ-1
Signed-off-by: P Praneesh <ppranees@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1604914915-12831-1-git-send-email-ppranees@codeaurora.org
The timer is to check if TCL HP isn't updated to target.
The timer will postpone itself if there are TX operations
during the interval, otherwise the timer handler updates
the HP again so the index value in HP register will be
forwarded to target register, and the timer stops afterwards.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601544890-13450-5-git-send-email-kvalo@codeaurora.org
Add packet log support for QCA6390, otherwise the data connection will stall
within a minute or so. Enable it via debugfs and use trace-cmd to capture the
pktlogs.
echo 0xffff 1 > /sys/kernel/debug/ath11k/qca6390\ hw2.0/mac0/pktlog_filter
The mon status ring doesn't support interrupt so far, so host starts
a timer to reap this ring. The timer handler also reaps the
rxdma_err_dst_ring in case of monitor mode.
As QCA6390 requires bss created ahead of starting vdev, so check
vdev_start_delay for monitor mode.
For QCA6390, it uses wbm_desc_rel_ring to return descriptors.
It also uses rx_refill_buf_ring to fill mon buffer instead of
rxdma_mon_buf_ring.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1601463073-12106-2-git-send-email-kvalo@codeaurora.org
Second set of patches for v5.10. Biggest change here is wcn3680
support to wcn36xx driver, otherwise smaller features. And naturally
the usual fixes and cleanups.
Major changes:
brcmfmac
* support 4-way handshake offloading for WPA/WPA2-PSK in AP mode
* support SAE authentication offload in AP mode
mt76
* mt7663 runtime power management improvements
* mt7915 A-MSDU offload
wcn36xx
* add support wcn3680 Wi-Fi 5 devices
ath11k
* spectral scan support for ipq6018
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJfbhn8AAoJEG4XJFUm622bFnMH/jI1Q+DXi2/sn3L01onNABqE
0M/HiZj/Gli2kYrIFiXKzCCVZBA/5CIZefh8Q+brsH4ZonJriTJ/VnJcGdDU68FK
ZqWSAkJ6+pJSaq7O/LofoTw+G0N64GPVN88ZqDMSoCyS8LDsE2QSjX6WEdeX7i9t
BWLcdXJ/brPzxtoH43c+w05syM+NCzPACUEKADa0KU5pg+MKHqtL/2FN8CecyU8k
ylzwH7w99mLBU3dDi8Q+EcUzOa0E+B7h56+BCcy/opCPZl0u2KGKcX/bRib1BwIB
wAChlEppwK/x8G8ViqxkrDVn1IiY2mnlFvdExuOlWqmVqwcccY8lEe19iAnzrV4=
=Xrmx
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-09-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.10
Second set of patches for v5.10. Biggest change here is wcn3680
support to wcn36xx driver, otherwise smaller features. And naturally
the usual fixes and cleanups.
Major changes:
brcmfmac
* support 4-way handshake offloading for WPA/WPA2-PSK in AP mode
* support SAE authentication offload in AP mode
mt76
* mt7663 runtime power management improvements
* mt7915 A-MSDU offload
wcn36xx
* add support wcn3680 Wi-Fi 5 devices
ath11k
* spectral scan support for ipq6018
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the function declarations are for functions in debugfs_htt_stats.c and
debugfs_sta.c, move them to corresponding header files. As debugfs_sta.h didn't
exist create it.
Also in debugfs_htt_stats.h move dunction declarations to the end of the file.
No functional changes. Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1600264523-12939-4-git-send-email-kvalo@codeaurora.org
In order to unify the tx status path, the hw 802.11 encapsulation flag
needs to survive the trip to the tx status call.
Since we don't have any free bits in info->flags, we need to move one.
IEEE80211_TX_INTFL_NEED_TXPROCESSING is only used internally in mac80211,
and only before the call into the driver.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Link: https://lore.kernel.org/r/20200908123702.88454-10-nbd@nbd.name
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adding raw mode tx/rx support. Also, adding support
for software crypto which depends on raw mode.
To enable raw mode tx/rx:
insmod ath11k.ko frame_mode=0
To enable software crypto:
insmod ath11k.ko crypto_mode=1
These modes could be helpful in debugging crypto related issues.
Tested-on: IPQ8074 WLAN.HK.2.1.0.1-01228-QCAHKSWPL_SILICONZ-1
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/010101746c6a52d9-18302a2c-0d6d-4057-aa4b-95960c809646-000000@us-west-2.amazonses.com
For QCA6390, wbm2sw1 is used for other purpose rather than
tx completion ring. So use TCL_DATA_RING 0 only for QCA6390.
Add MISC_CAPS_TCL_0_ONLY to control it.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-9-git-send-email-kvalo@codeaurora.org
For QCA6390, only one pdev is created and this pdev manages both lmacs, thus
both rxdmas. So host needs to initialize all rxdma related rings for one pdev.
Another difference is for QCA6390, host fills rxbuf to firmware and firmware
further fills the rxbuf to rxbuf ring for each rxdma.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597555891-26112-4-git-send-email-kvalo@codeaurora.org
On QCA6390 reg_start and reg_size values are different from IPQ8074 so we need
to change the values runtime. As we can't modify a static const variable
hw_srng_config directly, instead use it as a template, copy it and modify the
copy with correct values.
Tested-on: QCA6390 hw2.0 PCI WLAN.HST.1.0.1-01740-QCAHSTSWPLZ_V2_TO_X86-1
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01238-QCAHKSWPL_SILICONZ-2
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597389030-13887-12-git-send-email-kvalo@codeaurora.org
Add support for dp tx error stats which logs tx failure reasons due
to ring full condition, etc. This stats is added in soc_dp_stats
which was earlier used as soc_rx_stats so that all dp related info
are logged in same file.
Below is an example usage,
root@OpenWrt:/# cat /sys/kernel/debug/ath11k/ipq8074/soc_dp_stats
SOC RX STATS:
err ring pkts: 0
Invalid RBM: 0
<snip>
SOC TX STATS:
Ring Full Failures:
ring0: 4
ring1: 3
ring2: 5
Misc Transmit Failures: 2
Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.1.0.1-01213-QCAHKSWPL_SILICONZ-1
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1591768308-32005-2-git-send-email-srirrama@codeaurora.org
This patch adds support for ethernet rxtx mode to the driver. The feature
is enabled via a new module parameter. If enabled to driver will enable
the feature on a per vif basis if all other requirements were met.
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200430152814.18481-1-john@phrozen.org
IPQ8074 HW supports three TCL rings for tx. Currently these rings
are mapped based on the Access categories, viz. VO, VI, BE, BK.
In case, one of the traffic type dominates, then it could stress
the same tcl rings. Rather, it would be optimal to make use of all
the rings in a round robin fashion irrespective of the traffic type
so that the load could be evenly distributed among all the rings.
Also, in case the selected ring is busy or full, a retry mechanism
is used to ensure other available ring is selected without dropping
the packet.
In SMP systems, this change avoids a single CPU from getting hogged
when heavy traffic of same category is transmitted.
The tx completion interrupts corresponding to the used tcl ring
would be more which causes the assigned CPU to get hogged.
Distribution of tx packets to different tcl rings helps balance
this load.
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586782622-22570-1-git-send-email-srirrama@codeaurora.org
should not overwrite the error code. No buffer available then return
invalid. For other failures return the error code of actual failure.
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1586776872-25766-1-git-send-email-gsamin@codeaurora.org
As Hash based reo destination selection is configured,
the decapped packets reach different reo destintion rings
based on the destintaion ring selected for the computed hash (based on
the 5-tuple {ip src/ip dst/src port/dst port/protocol}) by hw and
as configured by driver.
Hence the current implementation of amsdu list based processing after all
the subframes of amsdu are received (since all msdu's for a pdev are
received in same reo dest ring), is not applicable here and hence is
replaced with per msdu based handling as these subframes
can be received in different reo dest rings.
Also, as some of the rx descriptor fields might be valid only for the
first msdu (for ex. received 80211 header, encryption type, etc),
it might not be useful now as we cannot sync between different
subframes received in different rings. Hence do not rely on those
fields and replace them with fieds valid only on per msdu descriptors.
Also cache other details such as encryption type for a peer so that
it can be reused when a packet is received from it.
Co-developed-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Tamizh Chelvam Raja <tamizhr@codeaurora.org>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Parse and store the out-of-band rates reported by the FW.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are two error paths where "ret" wasn't set. Also one error path
we set the error code to -EINVAL but we should just preserve the error
code from ath11k_hal_srng_get_entrysize(). That function only returns
-EINVAL so this doesn't change anything.
I removed the "ret = 0;" initializers so that hopefully GCC will be able
to detect these sorts of bugs in the future.
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the structure ts is not inititalized and ts.flags contains
garbage values from the stack. This is being passed into function
ath11k_dp_tx_status_parse that bit-wise or'ing in settings into the
ts.flags field. To avoid flags (and other fields) from containing
garbage, initialize the structure to zero before use.
Addresses-Coverity: ("Uninitialized scalar variable)"
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The error handling when the call to ath11k_hal_srng_get_entrysize fails
leaks skb, fix this by returning via the err_free return path that will
ensure the skb is free'd.
Addresses-Coverity: ("Resource leak")
Fixes: d5c65159f2 ("ath11k: driver for Qualcomm IEEE 802.11ax devices")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Moving the function into dp_tx.c allows gcc to optimize the code better
and also avoid chace invalidates and context switches.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the current code does 4 memcpys for each completion frame.
1) duplicate the desc
2 + 3) inside kfifo insertion
4) kfifo remove
The code simply drops the kfifo and uses a trivial ring buffer. This
requires a single memcpy for insertion. There is no removal needed as
we can simply use the inserted data for processing. As the code runs
inside the NAPI context it is atomic and there is no need for most of
the locking.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no point in zero'ing out the structure if we set all values in the
following line.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
remove unused counter to avoid taking locks inorder to optimize
cpu load.
Using Flamegraph, cpu usage of ath11k_dp_tx() observed to be decreased
from 5.58% to 3.74% with iperf traffic running with 80MHz bandwidth ap
mode.
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath11k is a new driver for Qualcomm IEEE 802.11ax devices, first
supporting only IPQ8074 SoC using the shared memory AHB bus. ath11k
uses mac80211 and supports AP, Station and Mesh modes.
Even though ath11k has some similar code as with ath10k (especially
the WMI layer) it was concluded to be simpler to have a "clean start"
for ath11k code base and not try to share the code with ath10k. This
makes maintenance easier and avoids major changes in ath10k, which
would have significantly increased the risk of regressions in existing
setups.
Even though the driver is very similar with ath10k but there are major
differences as well. The datapath is completely different. ath11k
supports multiple MACs, called "soc" in the firmware interface. And
there's only one WMI interface to support.
Currently ath11k supports only IEEE 802.11ac mode, but patches for
802.11ax are available and they will be submitted after ath11k is
accepted to upstream.
The firmware images are available from ath11k-firmware repository but
they will be also submitted to linux-firmware:
https://github.com/kvalo/ath11k-firmware
This was tested with firmware version WLAN.HK.2.1.0.1-00629-QCAHKSWPL_SILICONZ-1.
The driver has had multiple authors who are listed in alphabetical
order below.
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Ganesh Sesetti <gseset@codeaurora.org>
Signed-off-by: Govindaraj Saminathan <gsamin@codeaurora.org>
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Karthikeyan Periyasamy <periyasa@codeaurora.org>
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Miles Hu <milehu@codeaurora.org>
Signed-off-by: Muna Sinada <msinada@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Sathishkumar Muruganandam <murugana@codeaurora.org>
Signed-off-by: Shashidhar Lakkavalli <slakkavalli@datto.com>
Signed-off-by: Sriram R <srirrama@codeaurora.org>
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@codeaurora.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
