- Release previously-requested DW eDMA IRQs if request_irq() fails (Serge
Semin)
- Convert DW eDMA linked-list (ll) and data target (dt) from CPU-relative
addresses to PCI bus addresses (Serge Semin)
- Fix missing src/dst address for interleaved transfers (Serge Semin)
- Enforce the DW eDMA restriction that interleaved transfers must increment
src and dst addresses (Serge Semin)
- Fix some invalid interleaved transfer semantics (Serge Semin)
- Convert CPU-relative addresses to PCI bus addresses for eDMA engine
(Serge Semin)
- Drop chancnt initialization from dw-edma-core, since it is managed by the
dmaengine core, e.g., in dma_async_device_channel_register() (Serge Semin)
- Clean up bogus casting of debugfs_entries.reg addresses (Serge Semin)
- Ignore debugfs file/directory creation errors (Serge Semin)
- Allocate debugfs entries from the heap to prepare for multi-eDMA
platforms (Serge Semin)
- Simplify and rework register accessors to remove another obstacle to
multi-eDMA platforms (Serge Semin)
- Consolidate eDMA read/write channels in a single dma_device to simplify,
better reflect the hardware design, and avoid a debugfs complaint (Serge
Semin)
- Move eDMA-specific debugfs nodes into existing dmaengine subdirectory
(Serge Semin)
- Fix a readq_ch() truncation from 64 to 32 bits (Serge Semin)
- Use existing readq()/writeq rather than hand-coding new ones (Serge
Semin)
- Drop unnecessary data target region allocation in favor of existing
dw_edma_chip members (Serge Semin)
- Use parent device in eDMA controller name to prepare for multi-eDMA
platforms (Serge Semin)
- In addition to the existing MMIO accessors for linked list entries, add
support for ioremapped entries for use by eDMA in Root Ports or local
Endpoints (Serge Semin)
- Convert DW_EDMA_PCIE so it depends on DW_EDMA instead of selecting it
(Serge Semin)
- Allow DWC drivers to set streaming DMA masks larger than 32 bits;
previously both streaming and coherent DMA were limited to 32 bits
because some PCI devices only support coherent 32-bit DMA for MSI (Serge
Semin)
- Set 64-bit streaming and coherent DMA mask for the bt1 driver (Serge
Semin)
- Add DW Root Port and Endpoint controller support for eDMA (Serge Semin)
* pci/controller/dwc:
PCI: dwc: Add Root Port and Endpoint controller eDMA engine support
PCI: bt1: Set 64-bit DMA mask
PCI: dwc: Restrict only coherent DMA mask for MSI address allocation
dmaengine: dw-edma: Prepare dw_edma_probe() for builtin callers
dmaengine: dw-edma: Depend on DW_EDMA instead of selecting it
dmaengine: dw-edma: Add mem-mapped LL-entries support
dmaengine: dw-edma: Skip cleanup procedure if no private data found
dmaengine: dw-edma: Replace chip ID number with device name
dmaengine: dw-edma: Drop DT-region allocation
dmaengine: dw-edma: Use non-atomic io-64 methods
dmaengine: dw-edma: Fix readq_ch() return value truncation
dmaengine: dw-edma: Use DMA engine device debugfs subdirectory
dmaengine: dw-edma: Join read/write channels into a single device
dmaengine: dw-edma: Move eDMA data pointer to debugfs node descriptor
dmaengine: dw-edma: Simplify debugfs context CSRs init procedure
dmaengine: dw-edma: Rename debugfs dentry variables to 'dent'
dmaengine: dw-edma: Convert debugfs descs to being heap-allocated
dmaengine: dw-edma: Add dw_edma prefix to debugfs nodes descriptor
dmaengine: dw-edma: Stop checking debugfs_create_*() return value
dmaengine: dw-edma: Drop unnecessary debugfs reg casts
dmaengine: dw-edma: Drop chancnt initialization
dmaengine: dw-edma: Add PCI bus address getter to the remote EP glue driver
dmaengine: dw-edma: Add CPU to PCI bus address translation
dmaengine: dw-edma: Fix invalid interleaved xfers semantics
dmaengine: dw-edma: Don't permit non-inc interleaved xfers
dmaengine: dw-edma: Fix missing src/dst address of interleaved xfers
dmaengine: dw-edma: Convert ll/dt phys address to PCI bus/DMA address
dmaengine: dw-edma: Release requested IRQs on failure
dmaengine: Fix dma_slave_config.dst_addr description
- Convert dra7xx to threaded IRQ handler (Manivannan Sadhasivam)
- Move tegra194 dw_pcie_ep_linkup() to threaded IRQ handler (Manivannan
Sadhasivam)
- Add a separate lock for the endpoint pci_epf list to avoid deadlock
while running callbacks (Manivannan Sadhasivam)
- Use callbacks instead of notifier chains to signal events from EPC to EPF
drivers (Manivannan Sadhasivam)
- Use link_up() callback in place of LINK_UP notifier (Manivannan
Sadhasivam)
* pci/endpoint:
PCI: endpoint: Use link_up() callback in place of LINK_UP notifier
PCI: endpoint: Use callback mechanism for passing events from EPC to EPF
PCI: endpoint: Use a separate lock for protecting epc->pci_epf list
PCI: tegra194: Move dw_pcie_ep_linkup() to threaded IRQ handler
PCI: dra7xx: Use threaded IRQ handler for "dra7xx-pcie-main" IRQ
Since the DW eDMA core now supports eDMA controllers embedded in locally
accessible DW PCIe Root Ports and Endpoints, register these controllers
when possible.
To do that the DW PCIe core driver needs to perform some preparations
first. First of all, it needs to find the eDMA controller CSRs base
address, whether they are accessible over the Port Logic or iATU unrolled
space. Afterwards it can try to auto-detect the eDMA controller
availability and number of read/write channels. If none are found the
procedure silently returns without error.
Secondly, the platform is supposed to provide either combined or
per-channel IRQ signals. If no valid IRQs set is found, the procedure
returns without error to be backward compatible with platforms where DW
PCIe controllers have eDMA but lack the IRQ description.
Finally, before actually probing the eDMA device we need to allocate LLP
items buffers. After that the DW eDMA can be registered. If registration is
successful, a message regarding the number of detected Read/Write eDMA
channels will be printed to the system as is done for the iATU settings.
Note: the DW PCI controller driver (either host or endpoint mode) is
currently always built-in, so if the DW eDMA core is built as a module
(CONFIG_DW_EDMA=m), eDMA controllers will not be registered even if the
dw-edma module is later loaded.
Link: https://lore.kernel.org/r/20230113171409.30470-28-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
The DW PCIe Root Port IP core is synthesized with the 64-bit AXI address
bus. Since the device is also equipped with the eDMA engine, explicitly
set the device DMA mask so DMA engine clients can allocate data buffers
anywhere in the 64-bit memory space.
Link: https://lore.kernel.org/r/20230113171409.30470-27-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The MSI target address must be in the lowest 4GB memory to support PCI
peripherals without 64-bit MSI support. Since the allocation is done from
DMA coherent memory, set only the coherent DMA mask, leaving the streaming
DMA mask alone.
Thus streaming DMA operations will work with no artificial limitations. It
will be specifically useful for the eDMA-capable controllers so the
corresponding DMA engine clients would map the DMA buffers with no need for
SWIOTLB for buffers allocated above 4GB.
Add a brief comment about the reason allocating the MSI target address
below 4GB.
Link: https://lore.kernel.org/r/20230113171409.30470-26-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Since 8b41fc4454 ("kbuild: create modules.builtin without
Makefile.modbuiltin or tristate.conf"), MODULE_LICENSE declarations are
used to identify modules. As a consequence, MODULE_LICENSE in non-modules
causes modprobe to misidentify the object file as a module when it is not,
and modprobe might succeed rather than failing with a suitable error
message.
For tristate modules that can be either built-in or loaded at runtime,
modprobe succeeds in both cases:
# modprobe ext4
[exit status zero if CONFIG_EXT4_FS=y or =m]
For boolean modules like the Standard Hot Plug Controller driver (shpchp)
that cannot be loaded at runtime, modprobe should always fail like this:
# modprobe shpchp
modprobe: FATAL: Module shpchp not found in directory /lib/modules/...
[exit status non-zero regardless of CONFIG_HOTPLUG_PCI_SHPC]
but prior to this commit, shpchp_core.c contained MODULE_LICENSE, so
"modprobe shpchp" silently succeeded when it should have failed.
Remove MODULE_LICENSE in files that cannot be built as modules.
[bhelgaas: commit log, squash]
Suggested-by: Luis Chamberlain <mcgrof@kernel.org>
Link: https://lore.kernel.org/r/20230216152410.4312-1-nick.alcock@oracle.com/
Signed-off-by: Nick Alcock <nick.alcock@oracle.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Luis Chamberlain <mcgrof@kernel.org>
Cc: Hitomi Hasegawa <hasegawa-hitomi@fujitsu.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Lorenzo Pieralisi <lpieralisi@kernel.org>
IPQ8074 has one Gen2 and one Gen3 port, with Gen2 port already supported.
Add compatible for Gen3 port which uses the same controller as IPQ6018.
Link: https://lore.kernel.org/r/20230113164449.906002-7-robimarko@gmail.com
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Implement the new host_deinit() callback so that the PHY is powered off
and regulators and clocks are disabled also on late host-init errors.
Link: https://lore.kernel.org/r/20221017114705.8277-2-johan+linaro@kernel.org
Fixes: 82a823833f ("PCI: qcom: Add Qualcomm PCIe controller driver")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
dw_pcie_ep_linkup() may take more time to execute depending on the EPF
driver implementation. Calling this API in the hard IRQ handler is not
encouraged since the hard IRQ handlers are supposed to complete quickly.
So move the dw_pcie_ep_linkup() call to threaded IRQ handler.
Link: https://lore.kernel.org/linux-pci/20230124071158.5503-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
The "dra7xx-pcie-main" hard IRQ handler is just printing the IRQ status
and calling the dw_pcie_ep_linkup() API if LINK_UP status is set. But the
execution of dw_pcie_ep_linkup() depends on the EPF driver and may take
more time depending on the EPF implementation.
In general, hard IRQ handlers are supposed to return quickly and not block
for so long. Moreover, there is no real need of the current IRQ handler to
be a hard IRQ handler. So switch to the threaded IRQ handler for the
"dra7xx-pcie-main" IRQ.
Link: https://lore.kernel.org/linux-pci/20230124071158.5503-2-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Krzysztof Wilczyński <kwilczynski@kernel.org>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
i.MX PCIe is one dual mode PCIe controller.
Add i.MX PCIe EP mode support here, and split the PCIe modes to the Root
Complex mode and Endpoint mode.
Link: https://lore.kernel.org/r/1673847684-31893-12-git-send-email-hongxing.zhu@nxp.com
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
a474d3fbe2 ("PCI/MSI: Get rid of PCI_MSI_IRQ_DOMAIN") removed
PCI_MSI_IRQ_DOMAIN and changed all references to refer to PCI_MSI instead.
ba6ed462dc ("PCI: dwc: Add Baikal-T1 PCIe controller support")
independently added PCIE_BT1, depending on PCI_MSI_IRQ_DOMAIN.
Both commits appeared in v6.2-rc1, so the latter missed the conversion from
PCI_MSI_IRQ_DOMAIN to PCI_MSI. Update PCIE_BT1 to depend on PCI_MSI
instead.
[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20221215103452.23131-1-lukas.bulwahn@gmail.com
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
- New support:
- Allwinner H616 USB PHY and A100 DPHY support
- TI J721s2, J784s4 and J721e support
- Freescale i.MX8MP PCIe PHY support
- New driver for Renesas Ethernet SERDES supporting R-Car S4-8
- Qualcomm SM8450 PCIe1 PHY support in EP mode
- Updates:
- again a big pile of updates on qcom-qmp-* drivers following the
driver split and reorganization merged earlier
- Phy order of API calls documentation update
-----BEGIN PGP SIGNATURE-----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=4HRP
-----END PGP SIGNATURE-----
Merge tag 'phy-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy
Pull phy updates from Vinod Koul:
"This tme we have again a big pile of qcom-qmp-* changes, one new
driver and bunch of new hardware support.
New hardware support:
- Allwinner H616 USB PHY and A100 DPHY support
- TI J721s2, J784s4 and J721e support
- Freescale i.MX8MP PCIe PHY support
- New driver for Renesas Ethernet SERDES supporting R-Car S4-8
- Qualcomm SM8450 PCIe1 PHY support in EP mode
- Qualcomm SC8280XP PCIe PHY support (including x4 mode)
- Fixed Qualcomm SC8280XP USB4-USB3-DP PHY DT bindings
Updates:
- A big pile of updates on qcom-qmp-* drivers following the driver
split and reorganization merged earlier
- Phy order of API calls documentation update"
* tag 'phy-for-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/phy/linux-phy: (174 commits)
phy: ti: phy-j721e-wiz: add j721s2-wiz-10g module support
dt-bindings: phy-j721e-wiz: add j721s2 compatible string
phy: use devm_platform_get_and_ioremap_resource()
phy: allwinner: phy-sun6i-mipi-dphy: Add the A100 DPHY variant
phy: allwinner: phy-sun6i-mipi-dphy: Add a variant power-on hook
phy: allwinner: phy-sun6i-mipi-dphy: Set the enable bit last
phy: allwinner: phy-sun6i-mipi-dphy: Make RX support optional
dt-bindings: sun6i-a31-mipi-dphy: Add the A100 DPHY variant
dt-bindings: sun6i-a31-mipi-dphy: Add the interrupts property
phy: qcom-qmp-pcie: drop redundant clock allocation
phy: qcom-qmp-usb: drop redundant clock allocation
phy: qcom-qmp: drop unused type header
phy: qcom-qmp-usb: drop sc8280xp reference-clock source
dt-bindings: phy: qcom,sc8280xp-qmp-usb3-uni: drop reference-clock source
phy: qcom-qmp-combo: add support for updated sc8280xp binding
phy: qcom-qmp-combo: rename DP_PHY register pointer
phy: qcom-qmp-combo: rename common-register pointers
phy: qcom-qmp-combo: clean up DP clock callbacks
phy: qcom-qmp-combo: separate clock and provider registration
phy: qcom-qmp-combo: add clock registration helper
...
-----BEGIN PGP SIGNATURE-----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=KULr
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Squash portdrv_{core,pci}.c into portdrv.c to ease maintenance and
make more things static.
- Make portdrv bind to Switch Ports that have AER. Previously, if
these Ports lacked MSI/MSI-X, portdrv failed to bind, which meant
the Ports couldn't be suspended to low-power states. AER on these
Ports doesn't use interrupts, and the AER driver doesn't need to
claim them.
- Assign PCI domain IDs using ida_alloc(), which makes host bridge
add/remove work better.
Resource management:
- To work better with recent BIOSes that use EfiMemoryMappedIO for
PCI host bridge apertures, remove those regions from the E820 map
(E820 entries normally prevent us from allocating BARs). In v5.19,
we added some quirks to disable E820 checking, but that's not very
maintainable. EfiMemoryMappedIO means the OS needs to map the
region for use by EFI runtime services; it shouldn't prevent OS
from using it.
PCIe native device hotplug:
- Build pciehp by default if USB4 is enabled, since Thunderbolt/USB4
PCIe tunneling depends on native PCIe hotplug.
- Enable Command Completed Interrupt only if supported to avoid user
confusion from lspci output that says this is enabled but not
supported.
- Prevent pciehp from binding to Switch Upstream Ports; this happened
because of interaction with acpiphp and caused devices below the
Upstream Port to disappear.
Power management:
- Convert AGP drivers to generic power management. We hope to remove
legacy power management from the PCI core eventually.
Virtualization:
- Fix pci_device_is_present(), which previously always returned
"false" for VFs, causing virtio hangs when unbinding the driver.
Miscellaneous:
- Convert drivers to gpiod API to prepare for dropping some legacy
code.
- Fix DOE fencepost error for the maximum data object length.
Baikal-T1 PCIe controller driver:
- Add driver and DT bindings.
Broadcom STB PCIe controller driver:
- Enable Multi-MSI.
- Delay 100ms after PERST# deassert to allow power and clocks to
stabilize.
- Configure Read Completion Boundary to 64 bytes.
Freescale i.MX6 PCIe controller driver:
- Initialize PHY before deasserting core reset to fix a regression in
v6.0 on boards where the PHY provides the reference.
- Fix imx6sx and imx8mq clock names in DT schema.
Intel VMD host bridge driver:
- Fix Secondary Bus Reset on VMD bridges, which allows reset of NVMe
SSDs in VT-d pass-through scenarios.
- Disable MSI remapping, which gets re-enabled by firmware during
suspend/resume.
MediaTek PCIe Gen3 controller driver:
- Add MT7986 and MT8195 support.
Qualcomm PCIe controller driver:
- Add SC8280XP/SA8540P basic interconnect support.
Rockchip DesignWare PCIe controller driver:
- Base DT schema on common Synopsys schema.
Synopsys DesignWare PCIe core:
- Collect DT items shared between Root Port and Endpoint (PERST GPIO,
PHY info, clocks, resets, link speed, number of lanes, number of
iATU windows, interrupt info, etc) to snps,dw-pcie-common.yaml.
- Add dma-ranges support for Root Ports and Endpoints.
- Consolidate DT resource retrieval for "dbi", "dbi2", "atu", etc. to
reduce code duplication.
- Add generic names for clocks and resets to encourage more
consistent naming across drivers using DesignWare IP.
- Stop advertising PTM Responder role for Endpoints, which aren't
allowed to be responders.
TI J721E PCIe driver:
- Add j721s2 host mode ID to DT schema.
- Add interrupt properties to DT schema.
Toshiba Visconti PCIe controller driver:
- Fix interrupts array max constraints in DT schema"
* tag 'pci-v6.2-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (95 commits)
x86/PCI: Use pr_info() when possible
x86/PCI: Fix log message typo
x86/PCI: Tidy E820 removal messages
PCI: Skip allocate_resource() if too little space available
efi/x86: Remove EfiMemoryMappedIO from E820 map
PCI/portdrv: Allow AER service only for Root Ports & RCECs
PCI: xilinx-nwl: Fix coding style violations
PCI: mvebu: Switch to using gpiod API
PCI: pciehp: Enable Command Completed Interrupt only if supported
PCI: aardvark: Switch to using devm_gpiod_get_optional()
dt-bindings: PCI: mediatek-gen3: add support for mt7986
dt-bindings: PCI: mediatek-gen3: add SoC based clock config
dt-bindings: PCI: qcom: Allow 'dma-coherent' property
PCI: mt7621: Add sentinel to quirks table
PCI: vmd: Fix secondary bus reset for Intel bridges
PCI: endpoint: pci-epf-vntb: Fix sparse ntb->reg build warning
PCI: endpoint: pci-epf-vntb: Fix sparse build warning for epf_db
PCI: endpoint: pci-epf-vntb: Replace hardcoded 4 with sizeof(u32)
PCI: endpoint: pci-epf-vntb: Remove unused epf_db_phy struct member
PCI: endpoint: pci-epf-vntb: Fix call pci_epc_mem_free_addr() in error path
...
Baikal-T1 SoC is equipped with DWC PCIe v4.60a host controller. It can be
trained to work up to Gen.3 speed over up to x4 lanes. The host controller
is attached to the DW PCIe 3.0 PCS via the PIPE-4 interface, which in its
turn is connected to the DWC 10G PHY. The whole system is supposed to be
fed up with four clock sources: DBI peripheral clock, AXI application
clocks and external PHY/core reference clock generating the 100MHz signal.
In addition to that the platform provide a way to reset each part of the
controller: sticky/non-sticky bits, host controller core, PIPE interface,
PCS/PHY and Hot/Power reset signal. The driver also provides a way to
handle the GPIO-based PERST# signal.
Note due to the Baikal-T1 MMIO peculiarity we have to implement the DBI
interface accessors which make sure the IO operations are dword-aligned.
Link: https://lore.kernel.org/r/20221113191301.5526-21-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Currently almost each platform driver uses its own resets and clocks
naming in order to get the corresponding descriptors. It makes the code
harder to maintain and comprehend especially seeing the DWC PCIe core main
resets and clocks signals set hasn't changed much for about at least one
major IP-core release. So in order to organize things around these signals
we suggest to create a generic interface for them in accordance with the
naming introduced in the DWC PCIe IP-core reference manual:
Application clocks:
- "dbi" - data bus interface clock (on some DWC PCIe platforms it's
referred as "pclk", "pcie", "sys", "ahb", "cfg", "iface",
"gio", "reg", "pcie_apb_sys");
- "mstr" - AXI-bus master interface clock (some DWC PCIe glue drivers
refer to this clock as "port", "bus", "pcie_bus",
"bus_master/master_bus/axi_m", "pcie_aclk");
- "slv" - AXI-bus slave interface clock (also called as "port", "bus",
"pcie_bus", "bus_slave/slave_bus/axi_s", "pcie_aclk",
"pcie_inbound_axi").
Core clocks:
- "pipe" - core-PCS PIPE interface clock coming from external PHY (it's
normally named by the platform drivers as just "pipe");
- "core" - primary clock of the controller (none of the platform drivers
declare such a clock but in accordance with the ref. manual
the devices may have it separately specified);
- "aux" - auxiliary PMC domain clock (it is named by some platforms as
"pcie_aux" and just "aux");
- "ref" - Generic reference clock (it is a generic clock source, which
can be used as a signal source for multiple interfaces, some
platforms call it as "ref", "general", "pcie_phy",
"pcie_phy_ref").
Application resets:
- "dbi" - Data-bus interface reset (it's CSR interface clock and is
normally called as "apb" though technically it's not APB but
DWC PCIe-specific interface);
- "mstr" - AXI-bus master reset (some platforms call it as "port", "apps",
"bus", "axi_m");
- "slv" - ABI-bus slave reset (some platforms call it as "port", "apps",
"bus", "axi_s").
Core resets:
- "non-sticky" - non-sticky CSR flags reset;
- "sticky" - sticky CSR flags reset;
- "pipe" - PIPE-interface (Core-PCS) logic reset (some platforms
call it just "pipe");
- "core" - controller primary reset (resets everything except PMC
module, some platforms refer to this signal as "soft",
"pci");
- "phy" - PCS/PHY block reset (strictly speaking it is normally
connected to the input of an external block, but the
reference manual says it must be available for the PMC
working correctly, some existing platforms call it
"pciephy", "phy", "link");
- "hot" - PMC hot reset signal (also called as "sleep");
- "pwr" - cold reset signal (can be referred as "pwr", "turnoff").
Bus reset:
- "perst" - PCIe standard signal used to reset the PCIe peripheral
devices.
As you can see each platform uses it's own naming for basically the same
set of the signals. In the framework of this commit we suggest to add a
set of the clocks and reset signals resources, corresponding names and
identifiers for each denoted entity. At current stage the platforms will
be able to use the provided infrastructure to automatically request all
these resources and manipulate with them in the Host/EP init callbacks.
Alas it isn't that easy to create a common cold/hot reset procedure due to
too many platform-specifics in the procedure, like the external flags
exposure and the delays requirement.
Link: https://lore.kernel.org/r/20221113191301.5526-20-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Since the iATU CSR region is now retrieved in the DW PCIe resources getter
there is no much benefits in the iATU detection procedures splitting up.
Therefore let's join the iATU unroll/viewport detection procedure with the
rest of the iATU parameters detection code. The resultant method will be
as coherent as before, while the redundant functions will be eliminated
thus producing more readable code.
Link: https://lore.kernel.org/r/20221113191301.5526-19-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Currently the DW PCIe Root Port and Endpoint CSR spaces are retrieved in
the separate parts of the DW PCIe core driver. It doesn't really make
sense since the both controller types have identical set of the core CSR
regions: DBI, DBI CS2 and iATU/eDMA. Thus we can simplify the DW PCIe Host
and EP initialization methods by moving the platform-specific registers
space getting and mapping into a common method. It gets to be even more
justified seeing the CSRs base address pointers are preserved in the
common DW PCIe descriptor. Note all the OF-based common DW PCIe settings
initialization will be moved to the new method too in order to have a
single function for all the generic platform properties handling in single
place.
A nice side-effect of this change is that the pcie-designware-host.c and
pcie-designware-ep.c drivers are cleaned up from all the direct dw_pcie
storage modification, which makes the DW PCIe core, Root Port and Endpoint
modules more coherent.
Link: https://lore.kernel.org/r/20221113191301.5526-18-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Since in addition to the already available iATU unrolled mapping we are
about to add a few more DW PCIe platform-specific capabilities (CDM-check
and generic clocks/resets resources) let's add a generic interface to set
and get the flags indicating their availability. The new interface shall
improve maintainability of the platform-specific code.
Link: https://lore.kernel.org/r/20221113191301.5526-17-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
In accordance with the generic PCIe Root Port DT-bindings the "dma-ranges"
property has the same format as the "ranges" property. The only difference
is in their semantics. The "dma-ranges" property describes the PCIe-to-CPU
memory mapping in opposite to the CPU-to-PCIe mapping of the "ranges"
property. Even though the DW PCIe controllers are normally equipped with
the internal Address Translation Unit which inbound and outbound tables
can be used to implement both properties semantics, it was surprising for
me to discover that the host-related part of the DW PCIe driver currently
supports the "ranges" property only while the "dma-ranges" windows are
just ignored. Having the "dma-ranges" supported in the driver would be
very handy for the platforms, that don't tolerate the 1:1 CPU-PCIe memory
mapping and require a customized PCIe memory layout. So let's fix that by
introducing the "dma-ranges" property support.
First of all we suggest to rename the dw_pcie_prog_inbound_atu() method to
dw_pcie_prog_ep_inbound_atu() and create a new version of the
dw_pcie_prog_inbound_atu() function. Thus we'll have two methods for the
RC and EP controllers respectively in the same way as it has been
developed for the outbound ATU setup methods.
Secondly aside with the memory window index and type the new
dw_pcie_prog_inbound_atu() function will accept CPU address, PCIe address
and size as its arguments. These parameters define the PCIe and CPU memory
ranges which will be used to setup the respective inbound ATU mapping. The
passed parameters need to be verified against the ATU ranges constraints
in the same way as it is done for the outbound ranges.
Finally the DMA-ranges detected for the PCIe controller need to be
converted to the inbound ATU entries during the host controller
initialization procedure. It will be done in the framework of the
dw_pcie_iatu_setup() method. Note before setting the inbound ranges up we
need to disable all the inbound ATU entries in order to prevent unexpected
PCIe TLPs translations defined by some third party software like
bootloaders.
Link: https://lore.kernel.org/r/20221113191301.5526-16-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
What a zoo:
PCI_MSI
select GENERIC_MSI_IRQ
PCI_MSI_IRQ_DOMAIN
def_bool y
depends on PCI_MSI
select GENERIC_MSI_IRQ_DOMAIN
Ergo PCI_MSI enables PCI_MSI_IRQ_DOMAIN which in turn selects
GENERIC_MSI_IRQ_DOMAIN. So all the dependencies on PCI_MSI_IRQ_DOMAIN are
just an indirection to PCI_MSI.
Match the reality and just admit that PCI_MSI requires
GENERIC_MSI_IRQ_DOMAIN.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Link: https://lore.kernel.org/r/20221111122014.467556921@linutronix.de
This patch switches the driver away from legacy gpio/of_gpio API to
gpiod API, and removes use of of_get_named_gpio_flags() which I want to
make private to gpiolib.
Link: https://lore.kernel.org/r/20220906204301.3736813-1-dmitry.torokhov@gmail.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
When the PHY is the reference clock provider then it must be initialized
and powered on before the reset on the client is deasserted, otherwise
the link will never come up. The order was changed in cf236e0c0d.
Restore the correct order to make the driver work again on boards where
the PHY provides the reference clock. This also changes the order for
boards where the Soc is the PHY reference clock divider, but this
shouldn't do any harm.
Link: https://lore.kernel.org/r/20221101095714.440001-1-s.hauer@pengutronix.de
Fixes: cf236e0c0d ("PCI: imx6: Do not hide PHY driver callbacks and refine the error handling")
Tested-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
On Qualcomm platforms like SC8280XP and SA8540P, interconnect bandwidth
must be requested before enabling interconnect clocks.
Add basic support for managing an optional "pcie-mem" interconnect path
by setting a low constraint before enabling clocks and updating it after
the link is up.
Note that it is not possible for a controller driver to set anything but
a maximum peak bandwidth as expected average bandwidth will vary with
use case and actual use (and power policy?). This very much remains an
unresolved problem with the interconnect framework.
Also note that no constraint is set for the SC8280XP/SA8540P "cpu-pcie"
path for now as it is not clear what an appropriate constraint would be
(and the system does not crash when left unspecified).
Link: https://lore.kernel.org/r/20221102090705.23634-3-johan+linaro@kernel.org
Fixes: 70574511f3 ("PCI: qcom: Add support for SC8280XP")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Brian Masney <bmasney@redhat.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Acked-by: Georgi Djakov <djakov@kernel.org>
Many host controller drivers #include <linux/of_irq.h> even though they
don't need it. Remove the unnecessary #includes.
Link: https://lore.kernel.org/r/20221031153954.1163623-6-helgaas@kernel.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Roy Zang <roy.zang@nxp.com>
Some of the platforms (like Tegra194 and Tegra234) have open slots and
not having an endpoint connected to the slot is not an error.
So, changing the macro from dev_err to dev_info to log the event.
Link: https://lore.kernel.org/r/20220913101237.4337-1-vidyas@nvidia.com
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Dual mode DesignWare PCIe IP has PTM capability enabled (if supported) even
in the EP mode. The PCIe compliance for the EP mode expects PTM
capabilities (ROOT_CAPABLE, RES_CAPABLE, CLK_GRAN) be disabled.
Hence disable PTM for the EP mode.
Link: https://lore.kernel.org/r/20220919143340.4527-3-vidyas@nvidia.com
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
commit aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
incorrectly uses pci->link_gen in deriving the index to the
n_fts[] array also introducing the issue of accessing beyond the
boundaries of array for greater than Gen-2 speeds. This change fixes
that issue.
Link: https://lore.kernel.org/r/20220926111923.22487-1-vidyas@nvidia.com
Fixes: aeaa0bfe89 ("PCI: dwc: Move N_FTS setup to common setup")
Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Jingoo Han <jingoohan1@gmail.com>
Call phy_set_mode_ext() to notify the PHY driver that the PHY is being
used in the EP mode.
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/20220927092207.161501-6-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Call phy_set_mode_ext() to notify the PHY driver that the PHY is being
used in the RC mode.
Reviewed-by: Jingoo Han <jingoohan1@gmail.com>
Reviewed-by: Johan Hovold <johan+linaro@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Link: https://lore.kernel.org/r/20220927092207.161501-5-dmitry.baryshkov@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
- List platforms that use a single MSI host interrupt in qcom DT (Johan
Hovold)
- Add SC8280XP, SA8540P support to qcom DT binding and driver(Johan Hovold)
- Make all optional clocks truly optional in the driver (Johan Hovold)
- Rename per-IP structs to reflect the IP version (Johan Hovold)
- Sort device ID match table by compatible string (Johan Hovold)
- Add MODULE_DEVICE_TABLE to enable module autoloading (Dmitry Baryshkov)
- Drop the unused .post_deinit() callback (Johan Hovold)
- Rely on DT for clock information instead of hard-coding it in the driver
(Manivannan Sadhasivam)
- Disable IRQs when removing driver to avoid spurious IRQs later
(Manivannan Sadhasivam)
- Expose link transition counts via debugfs to help debug issues with
low-power states (Manivannan Sadhasivam)
- Gate Master AXI clock to the MHI bus while in L1 substates to save power
(Manivannan Sadhasivam)
- Disable Master AXI clock to save power when there is no traffic on PCIe
(Manivannan Sadhasivam)
- Make the "PERST separation" debug feature optional in the DT and the
driver (Manivannan Sadhasivam)
- Define clocks to be per-platform in DT to prepare for future SoCs
(Manivannan Sadhasivam)
- Add SM8450 SoC support (Manivannan Sadhasivam)
- Check for platform_get_resource_byname() to avoid a NULL pointer
dereference (Yang Yingliang)
* pci/qcom:
PCI: qcom-ep: Check platform_get_resource_byname() return value
PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Add support for SM8450 SoC
dt-bindings: PCI: qcom-ep: Define clocks per platform
PCI: qcom-ep: Make PERST separation optional
dt-bindings: PCI: qcom-ep: Make PERST separation optional
PCI: qcom-ep: Disable Master AXI Clock when there is no PCIe traffic
PCI: qcom-ep: Gate Master AXI clock to MHI bus during L1SS
PCI: qcom-ep: Expose link transition counts via debugfs
PCI: qcom-ep: Disable IRQs during driver remove
PCI: qcom-ep: Make use of the cached dev pointer
PCI: qcom-ep: Rely on the clocks supplied by devicetree
PCI: qcom-ep: Add kernel-doc for qcom_pcie_ep structure
PCI: qcom: Rename host-init error label
PCI: qcom: Drop unused post_deinit callback
PCI: qcom-ep: Add MODULE_DEVICE_TABLE
PCI: qcom: Sort device-id table
PCI: qcom: Clean up IP configurations
PCI: qcom: Make all optional clocks optional
PCI: qcom: Add support for SA8540P
PCI: qcom: Add support for SC8280XP
dt-bindings: PCI: qcom: Add SA8540P to binding
dt-bindings: PCI: qcom: Add SC8280XP to binding
dt-bindings: PCI: qcom: Enumerate platforms with single msi interrupt
If platform_get_resource_byname() fails, 'mmio_res' will be set to NULL
pointer, which causes a NULL pointer dereference when it is used in
qcom_pcie_perst_deassert().
Check the return value to prevent it.
Link: https://lore.kernel.org/r/20220429080740.1294797-1-yangyingliang@huawei.com
Fixes: f55fee56a6 ("PCI: qcom-ep: Add Qualcomm PCIe Endpoint controller driver")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Add support for SM8450 SoC to the Qualcomm PCIe Endpoint Controller
driver. The driver uses the same config as the existing SDX55 chipset,
so additional settings are not required.
Link: https://lore.kernel.org/r/20220914075350.7992-13-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
PERST separation is an optional debug feature used to collect the crash
dump from the PCIe endpoint devices by the PCIe host when the endpoint
crashes. This feature keeps the PCIe link up by separating the PCIe IP
block from the SoC reset logic.
Make the property optional in the driver.
Link: https://lore.kernel.org/r/20220914075350.7992-10-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
The Master AXI clock can be disabled when it is not used i.e., when there
is no traffic on the PCIe bus. This helps to save power during idle state.
[bhelgaas: tidy and wrap comment]
Link: https://lore.kernel.org/r/20220914075350.7992-8-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Qualcomm PCIe controllers have debug registers in the MMIO region
that count PCIe link transitions. Expose them over debugfs to
userspace to help debug the low power issues.
Link: https://lore.kernel.org/r/20220914075350.7992-6-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Disable the Global and PERST IRQs during driver remove to avoid getting
spurious IRQs after resource deallocation.
Link: https://lore.kernel.org/r/20220914075350.7992-5-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
In the qcom_pcie_ep_get_resources() function, dev pointer is already
cached in a local variable. So let's make use of it instead of getting
the dev pointer again from pdev struct.
Link: https://lore.kernel.org/r/20220914075350.7992-4-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Generally, device drivers should just rely on the platform data like
devicetree to supply the clocks required for the functioning of the
peripheral. There is no need to hardcode the clk info in the driver.
So get rid of the static clk info and obtain the platform supplied
clks.
The total number of clocks supplied is obtained using the
devm_clk_bulk_get_all() API and used for the rest of the clk_bulk_ APIs.
Link: https://lore.kernel.org/r/20220914075350.7992-3-manivannan.sadhasivam@linaro.org
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Refer to phy_core driver, phy_init() must be called before phy_power_on().
Fix the wrong order of phy_init() and phy_power_on() here.
Link: https://lore.kernel.org/r/1662344583-18874-1-git-send-email-hongxing.zhu@nxp.com
Fixes: 1aa97b0022 ("phy: freescale: pcie: Initialize the imx8 pcie standalone phy driver")
Tested-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Lorenzo Pieralisi <lpieralisi@kernel.org>
