Formerly, we had to access the RELA and RELR tables via the kernel
mapping that was being relocated, and so deriving the start and end
addresses using ADRP/ADD references was not possible, as the relocation
code runs from the ID map.
Now that we map the entire kernel image via the ID map, we can simplify
this, and just load the entries via the ID map as well.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220624150651.1358849-14-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
As a first step towards avoiding the need to create, tear down and
recreate the kernel virtual mapping with MMU and caches disabled, start
by expanding the ID map so it covers the page tables as well as all
executable code. This will allow us to populate the page tables with the
MMU and caches on, and call KASLR init code before setting up the
virtual mapping.
Since this ID map is only needed at boot, create it as a temporary set
of page tables, and populate the permanent ID map after enabling the MMU
and caches. While at it, switch to read-only attributes for the where
possible, as writable permissions are only needed for the initial kernel
page tables. Note that on 4k granule configurations, the permanent ID
map will now be reduced to a single page rather than a 2M block mapping.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220624150651.1358849-13-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The asm macros used to create the initial ID map and kernel mappings
don't support randomly remapping parts of the address space after it has
been populated. What we can do, however, given that all block or page
mappings are created at the final level, is take a subset of the mapped
range and update its attributes or output address. This will permit us
to make parts of these page tables read-only, or remap a part of it to
cover the device tree.
So add a helper that encapsulates this.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220624150651.1358849-12-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
We will be adding an initial ID map that covers the entire kernel image,
so we will pass the actual ID map root table to use to __enable_mmu(),
rather than hard code it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220624150651.1358849-10-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Split off the creation of the ID map page tables, so that we can avoid
running it again unnecessarily when KASLR is in effect (which only
randomizes the virtual placement). This will permit us to drop some
explicit cache maintenance to the PoC which was necessary because the
cache invalidation being performed on some global variables might
otherwise clobber unrelated variables that happen to share a cacheline.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220624150651.1358849-8-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
In a future patch, we will start using an ID map that covers the entire
image, rather than a single page. This means that we need to deal with
the pathological case of an extended ID map where the kernel image does
not fit neatly inside a single entry at the root level, which means we
will need to create additional table entries and map additional pages
for page tables.
The existing map_memory macro already takes care of most of that, so
let's just extend it to deal with this case as well. While at it, drop
the conditional branch on the value of T0SZ: we don't set the variable
anymore in the entry code, and so we can just let the map_memory macro
deal with the case where the output address exceeds VA_BITS.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220624150651.1358849-7-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Simplify the macros in head.S that are used to set up the early page
tables, by switching to immediates for the number of bits that are
interpreted as the table index at each level. This makes it much
easier to infer from the instruction stream what is going on, and
reduces the number of instructions emitted substantially.
Note that the extended ID map for cases where no additional level needs
to be configured now uses a compile time size as well, which means that
we interpret up to 10 bits as the table index at the root level (for
52-bit physical addressing), without taking into account whether or not
this is supported on the current system. However, those bits can only
be set if we are executing the image from an address that exceeds the
48-bit PA range, and are guaranteed to be cleared otherwise, and given
that we are dealing with a mapping in the lower TTBR0 range of the
address space, the result is therefore the same as if we'd mask off only
6 bits.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220624150651.1358849-6-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The assignment of idmap_ptrs_per_pgd lacks any cache invalidation, even
though it is updated with the MMU and caches disabled. However, we never
bother to read the value again except in the very next instruction, and
so we can just drop the variable entirely.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20220624150651.1358849-5-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Setting idmap_t0sz involves fiddling with the caches if done with the
MMU off. Since we will be creating an initial ID map with the MMU and
caches off, and the permanent ID map with the MMU and caches on, let's
move this assignment of idmap_t0sz out of the startup code, and replace
it with a macro that simply issues the three instructions needed to
calculate the value wherever it is needed before the MMU is turned on.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220624150651.1358849-4-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Currently, we only support 52-bit virtual addressing on 64k pages
configurations, and in all other cases, vabits_actual is guaranteed to
equal VA_BITS (== VA_BITS_MIN). So get rid of the variable entirely in
that case.
While at it, move the assignment out of the asm entry code - it has no
need to be there.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20220624150651.1358849-3-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
This variable definition does not need to be in head.S so move it out.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Reviewed-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/20220624150651.1358849-2-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
THREAD_INFO_IN_TASK moved the CPU field out of thread_info, but this
causes some issues on architectures that define raw_smp_processor_id()
in terms of this field, due to the fact that #include'ing linux/sched.h
to get at struct task_struct is problematic in terms of circular
dependencies.
Given that thread_info and task_struct are the same data structure
anyway when THREAD_INFO_IN_TASK=y, let's move it back so that having
access to the type definition of struct thread_info is sufficient to
reference the CPU number of the current task.
Note that this requires THREAD_INFO_IN_TASK's definition of the
task_thread_info() helper to be updated, as task_cpu() takes a
pointer-to-const, whereas task_thread_info() (which is used to generate
lvalues as well), needs a non-const pointer. So make it a macro instead.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
The `compute_indices` and `populate_entries` macros operate on inclusive
bounds, and thus the `map_memory` macro which uses them also operates
on inclusive bounds.
We pass `_end` and `_idmap_text_end` to `map_memory`, but these are
exclusive bounds, and if one of these is sufficiently aligned (as a
result of kernel configuration, physical placement, and KASLR), then:
* In `compute_indices`, the computed `iend` will be in the page/block *after*
the final byte of the intended mapping.
* In `populate_entries`, an unnecessary entry will be created at the end
of each level of table. At the leaf level, this entry will map up to
SWAPPER_BLOCK_SIZE bytes of physical addresses that we did not intend
to map.
As we may map up to SWAPPER_BLOCK_SIZE bytes more than intended, we may
violate the boot protocol and map physical address past the 2MiB-aligned
end address we are permitted to map. As we map these with Normal memory
attributes, this may result in further problems depending on what these
physical addresses correspond to.
The final entry at each level may require an additional table at that
level. As EARLY_ENTRIES() calculates an inclusive bound, we allocate
enough memory for this.
Avoid the extraneous mapping by having map_memory convert the exclusive
end address to an inclusive end address by subtracting one, and do
likewise in EARLY_ENTRIES() when calculating the number of required
tables. For clarity, comments are updated to more clearly document which
boundaries the macros operate on. For consistency with the other
macros, the comments in map_memory are also updated to describe `vstart`
and `vend` as virtual addresses.
Fixes: 0370b31e48 ("arm64: Extend early page table code to allow for larger kernels")
Cc: <stable@vger.kernel.org> # 4.16.x
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Anshuman Khandual <anshuman.khandual@arm.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Steve Capper <steve.capper@arm.com>
Cc: Will Deacon <will@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210823101253.55567-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Lots of cleanup to our various page-table definitions, but also some
non-critical fixes and removal of some unnecessary memory types. The
most interesting change here is the reduction of ARCH_DMA_MINALIGN back
to 64 bytes, since we're not aware of any machines that need a higher
value with the way the code is structured (only needed for non-coherent
DMA).
* for-next/mm:
arm64: tlb: fix the TTL value of tlb_get_level
arm64/mm: Rename ARM64_SWAPPER_USES_SECTION_MAPS
arm64: head: fix code comments in set_cpu_boot_mode_flag
arm64: mm: drop unused __pa(__idmap_text_start)
arm64: mm: fix the count comments in compute_indices
arm64/mm: Fix ttbr0 values stored in struct thread_info for software-pan
arm64: mm: Pass original fault address to handle_mm_fault()
arm64/mm: Drop SECTION_[SHIFT|SIZE|MASK]
arm64/mm: Use CONT_PMD_SHIFT for ARM64_MEMSTART_SHIFT
arm64/mm: Drop SWAPPER_INIT_MAP_SIZE
arm64: mm: decode xFSC in mem_abort_decode()
arm64: mm: Add is_el1_data_abort() helper
arm64: cache: Lower ARCH_DMA_MINALIGN to 64 (L1_CACHE_BYTES)
arm64: mm: Remove unused support for Normal-WT memory type
arm64: acpi: Map EFI_MEMORY_WT memory as Normal-NC
arm64: mm: Remove unused support for Device-GRE memory type
arm64: mm: Use better bitmap_zalloc()
arm64/mm: Make vmemmap_free() available only with CONFIG_MEMORY_HOTPLUG
arm64/mm: Remove [PUD|PMD]_TABLE_BIT from [pud|pmd]_bad()
arm64/mm: Validate CONFIG_PGTABLE_LEVELS
Big cleanup of our cache maintenance routines, which were confusingly
named and inconsistent in their implementations.
* for-next/caches:
arm64: Rename arm64-internal cache maintenance functions
arm64: Fix cache maintenance function comments
arm64: sync_icache_aliases to take end parameter instead of size
arm64: __clean_dcache_area_pou to take end parameter instead of size
arm64: __clean_dcache_area_pop to take end parameter instead of size
arm64: __clean_dcache_area_poc to take end parameter instead of size
arm64: __flush_dcache_area to take end parameter instead of size
arm64: dcache_by_line_op to take end parameter instead of size
arm64: __inval_dcache_area to take end parameter instead of size
arm64: Fix comments to refer to correct function __flush_icache_range
arm64: Move documentation of dcache_by_line_op
arm64: assembler: remove user_alt
arm64: Downgrade flush_icache_range to invalidate
arm64: Do not enable uaccess for invalidate_icache_range
arm64: Do not enable uaccess for flush_icache_range
arm64: Apply errata to swsusp_arch_suspend_exit
arm64: assembler: add conditional cache fixups
arm64: assembler: replace `kaddr` with `addr`
Up to here, the CPU boot mode can either be EL1 or EL2.
Correct the code comments a bit.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210518101405.1048860-5-aisheng.dong@nxp.com
Signed-off-by: Will Deacon <will@kernel.org>
x5 is not used in the following map_memory. Instead,
__pa(__idmap_text_start) is stored in x3 which is used later.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210518101405.1048860-4-aisheng.dong@nxp.com
Signed-off-by: Will Deacon <will@kernel.org>
'count - 1' is confusing and not comply with the real code running.
'count' actually represents the extra entries required, no need minus 1.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210518101405.1048860-3-aisheng.dong@nxp.com
Signed-off-by: Will Deacon <will@kernel.org>
The scs_load and scs_save asm macros don't make use of the mandatory
'tmp' register argument, so drop it and fix up the callers.
Cc: Sami Tolvanen <samitolvanen@google.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Sami Tolvanen <samitolvanen@google.com>
Link: https://lore.kernel.org/r/20210527105529.21967-1-will@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Now that we have a consistent place to initialize CPU context registers
early in the boot path, let's also initialize the per-cpu offset here.
This makes the primary and secondary boot paths more consistent, and
allows for the use of per-cpu operations earlier, which will be
necessary for instrumentation with KCSAN.
Note that smp_prepare_boot_cpu() still needs to re-initialize CPU0's
offset as immediately prior to this the per-cpu areas may be
reallocated, and hence the boot-time offset may be stale. A comment is
added to make this clear.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210520115031.18509-7-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Once we enable the MMU, we have to initialize:
* SP_EL0 to point at the active task
* SP to point at the active task's stack
* SCS_SP to point at the active task's shadow stack
For all tasks (including init_task), this information can be derived
from the task's task_struct.
Let's unify __primary_switched and __secondary_switched to consistently
acquire this information from the relevant task_struct. At the same
time, let's fold this together with initializing a task's final frame.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210520115031.18509-6-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
When we boot a secondary CPU, we pass it a task and a stack to use. As
the stack is always the task's stack, which can be derived from the
task, let's have the secondary CPU derive this itself and avoid passing
redundant information.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Suzuki Poulose <suzuki.poulose@arm.com>
Cc: Will Deacon <will@kernel.org>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210520115031.18509-5-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Although naming across the codebase isn't that consistent, it
tends to follow certain patterns. Moreover, the term "flush"
isn't defined in the Arm Architecture reference manual, and might
be interpreted to mean clean, invalidate, or both for a cache.
Rename arm64-internal functions to make the naming internally
consistent, as well as making it consistent with the Arm ARM, by
specifying whether it applies to the instruction, data, or both
caches, whether the operation is a clean, invalidate, or both.
Also specify which point the operation applies to, i.e., to the
point of unification (PoU), coherency (PoC), or persistence
(PoP).
This commit applies the following sed transformation to all files
under arch/arm64:
"s/\b__flush_cache_range\b/caches_clean_inval_pou_macro/g;"\
"s/\b__flush_icache_range\b/caches_clean_inval_pou/g;"\
"s/\binvalidate_icache_range\b/icache_inval_pou/g;"\
"s/\b__flush_dcache_area\b/dcache_clean_inval_poc/g;"\
"s/\b__inval_dcache_area\b/dcache_inval_poc/g;"\
"s/__clean_dcache_area_poc\b/dcache_clean_poc/g;"\
"s/\b__clean_dcache_area_pop\b/dcache_clean_pop/g;"\
"s/\b__clean_dcache_area_pou\b/dcache_clean_pou/g;"\
"s/\b__flush_cache_user_range\b/caches_clean_inval_user_pou/g;"\
"s/\b__flush_icache_all\b/icache_inval_all_pou/g;"
Note that __clean_dcache_area_poc is deliberately missing a word
boundary check at the beginning in order to match the efistub
symbols in image-vars.h.
Also note that, despite its name, __flush_icache_range operates
on both instruction and data caches. The name change here
reflects that.
No functional change intended.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-19-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
To be consistent with other functions with similar names and
functionality in cacheflush.h, cache.S, and cachetlb.rst, change
to specify the range in terms of start and end, as opposed to
start and size.
Because the code is shared with __dma_inv_area, it changes the
parameters for that as well. However, __dma_inv_area is local to
cache.S, so no other users are affected.
No functional change intended.
Reported-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Fuad Tabba <tabba@google.com>
Reviewed-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210524083001.2586635-11-tabba@google.com
Signed-off-by: Will Deacon <will@kernel.org>
Reliable stacktracing requires that we identify when a stacktrace is
terminated early. We can do this by ensuring all tasks have a final
frame record at a known location on their task stack, and checking
that this is the final frame record in the chain.
We'd like to use task_pt_regs(task)->stackframe as the final frame
record, as this is already setup upon exception entry from EL0. For
kernel tasks we need to consistently reserve the pt_regs and point x29
at this, which we can do with small changes to __primary_switched,
__secondary_switched, and copy_process().
Since the final frame record must be at a specific location, we must
create the final frame record in __primary_switched and
__secondary_switched rather than leaving this to start_kernel and
secondary_start_kernel. Thus, __primary_switched and
__secondary_switched will now show up in stacktraces for the idle tasks.
Since the final frame record is now identified by its location rather
than by its contents, we identify it at the start of unwind_frame(),
before we read any values from it.
External debuggers may terminate the stack trace when FP == 0. In the
pt_regs->stackframe, the PC is 0 as well. So, stack traces taken in the
debugger may print an extra record 0x0 at the end. While this is not
pretty, this does not do any harm. This is a small price to pay for
having reliable stack trace termination in the kernel. That said, gdb
does not show the extra record probably because it uses DWARF and not
frame pointers for stack traces.
Signed-off-by: Madhavan T. Venkataraman <madvenka@linux.microsoft.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
[Mark: rebase, use ASM_BUG(), update comments, update commit message]
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210510110026.18061-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
It seems that the CPUs part of the SoC known as Apple M1 have the
terrible habit of being stuck with HCR_EL2.E2H==1, in violation
of the architecture.
Try and work around this deplorable state of affairs by detecting
the stuck bit early and short-circuit the nVHE dance. Additional
filtering code ensures that attempts at switching to nVHE from
the command-line are also ignored.
It is still unknown whether there are many more such nuggets
to be found...
Reported-by: Hector Martin <marcan@marcan.st>
Acked-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20210408131010.1109027-3-maz@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
52-bit VA kernels can run on hardware that is only 48-bit capable, but
configure the ID map as 52-bit by default. This was not a problem until
recently, because the special T0SZ value for a 52-bit VA space was never
programmed into the TCR register anwyay, and because a 52-bit ID map
happens to use the same number of translation levels as a 48-bit one.
This behavior was changed by commit 1401bef703 ("arm64: mm: Always update
TCR_EL1 from __cpu_set_tcr_t0sz()"), which causes the unsupported T0SZ
value for a 52-bit VA to be programmed into TCR_EL1. While some hardware
simply ignores this, Mark reports that Amberwing systems choke on this,
resulting in a broken boot. But even before that commit, the unsupported
idmap_t0sz value was exposed to KVM and used to program TCR_EL2 incorrectly
as well.
Given that we already have to deal with address spaces being either 48-bit
or 52-bit in size, the cleanest approach seems to be to simply default to
a 48-bit VA ID map, and only switch to a 52-bit one if the placement of the
kernel in DRAM requires it. This is guaranteed not to happen unless the
system is actually 52-bit VA capable.
Fixes: 90ec95cda9 ("arm64: mm: Introduce VA_BITS_MIN")
Reported-by: Mark Salter <msalter@redhat.com>
Link: http://lore.kernel.org/r/20210310003216.410037-1-msalter@redhat.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20210310171515.416643-2-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
As per ARM ARM DDI 0487G.a, when FEAT_LPA2 is implemented, ID_AA64MMFR0_EL1
might contain a range of values to describe supported translation granules
(4K and 16K pages sizes in particular) instead of just enabled or disabled
values. This changes __enable_mmu() function to handle complete acceptable
range of values (depending on whether the field is signed or unsigned) now
represented with ID_AA64MMFR0_TGRAN_SUPPORTED_[MIN..MAX] pair. While here,
also fix similar situations in EFI stub and KVM as well.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: kvmarm@lists.cs.columbia.edu
Cc: linux-efi@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Acked-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Anshuman Khandual <anshuman.khandual@arm.com>
Link: https://lore.kernel.org/r/1615355590-21102-1-git-send-email-anshuman.khandual@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
Although there has been a bit of back and forth on the subject, it
appears that invalidating TLBs requires an ISB instruction when FEAT_ETS
is not implemented by the CPU.
From the bible:
| In an implementation that does not implement FEAT_ETS, a TLB
| maintenance instruction executed by a PE, PEx, can complete at any
| time after it is issued, but is only guaranteed to be finished for a
| PE, PEx, after the execution of DSB by the PEx followed by a Context
| synchronization event
Add the missing ISB in __primary_switch, just in case.
Fixes: 3c5e9f238b ("arm64: head.S: move KASLR processing out of __enable_mmu()")
Suggested-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210224093738.3629662-3-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
Defer enabling pointer authentication on boot core until
after its required to be enabled by cpufeature framework.
This will help in controlling the feature dynamically
with a boot parameter.
Signed-off-by: Ajay Patil <pajay@qti.qualcomm.com>
Signed-off-by: Prasad Sodagudi <psodagud@codeaurora.org>
Signed-off-by: Srinivas Ramana <sramana@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/1610152163-16554-2-git-send-email-sramana@codeaurora.org
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Brazdil <dbrazdil@google.com>
Link: https://lore.kernel.org/r/20210208095732.3267263-22-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
In order to be able to override CPU features at boot time,
let's add a command line parser that matches options of the
form "cpureg.feature=value", and store the corresponding
value into the override val/mask pair.
No features are currently defined, so no expected change in
functionality.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: David Brazdil <dbrazdil@google.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210208095732.3267263-14-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
As we want to parse more options very early in the kernel lifetime,
let's always map the FDT early. This is achieved by moving that
code out of kaslr_early_init().
No functional change expected.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Brazdil <dbrazdil@google.com>
Link: https://lore.kernel.org/r/20210208095732.3267263-13-maz@kernel.org
[will: Ensue KASAN is enabled before running C code]
Signed-off-by: Will Deacon <will@kernel.org>
We can now move the initial SCTLR_EL1 setup to be used for both
EL1 and EL2 setup.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Brazdil <dbrazdil@google.com>
Link: https://lore.kernel.org/r/20210208095732.3267263-10-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
As init_el2_state is now nVHE only, let's simplify it and drop
the VHE setup.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: David Brazdil <dbrazdil@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210208095732.3267263-9-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
As we are aiming to be able to control whether we enable VHE or
not, let's always drop down to EL1 first, and only then upgrade
to VHE if at all possible.
This means that if the kernel is booted at EL2, we always start
with a nVHE init, drop to EL1 to initialise the the kernel, and
only then upgrade the kernel EL to EL2 if possible (the process
is obviously shortened for secondary CPUs).
The resume path is handled similarly to a secondary CPU boot.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: David Brazdil <dbrazdil@google.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Link: https://lore.kernel.org/r/20210208095732.3267263-6-maz@kernel.org
[will: Avoid calling switch_to_vhe twice on kaslr path]
Signed-off-by: Will Deacon <will@kernel.org>
Turning the MMU on is a popular sport in the arm64 kernel, and
we do it more than once, or even twice. As we are about to add
even more, let's turn it into a macro.
No expected functional change.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Brazdil <dbrazdil@google.com>
Link: https://lore.kernel.org/r/20210208095732.3267263-4-maz@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
* PSCI relay at EL2 when "protected KVM" is enabled
* New exception injection code
* Simplification of AArch32 system register handling
* Fix PMU accesses when no PMU is enabled
* Expose CSV3 on non-Meltdown hosts
* Cache hierarchy discovery fixes
* PV steal-time cleanups
* Allow function pointers at EL2
* Various host EL2 entry cleanups
* Simplification of the EL2 vector allocation
s390:
* memcg accouting for s390 specific parts of kvm and gmap
* selftest for diag318
* new kvm_stat for when async_pf falls back to sync
x86:
* Tracepoints for the new pagetable code from 5.10
* Catch VFIO and KVM irqfd events before userspace
* Reporting dirty pages to userspace with a ring buffer
* SEV-ES host support
* Nested VMX support for wait-for-SIPI activity state
* New feature flag (AVX512 FP16)
* New system ioctl to report Hyper-V-compatible paravirtualization features
Generic:
* Selftest improvements
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEE8TM4V0tmI4mGbHaCv/vSX3jHroMFAl/bdL4UHHBib256aW5p
QHJlZGhhdC5jb20ACgkQv/vSX3jHroNgQQgAnTH6rhXa++Zd5F0EM2NwXwz3iEGb
lOq1DZSGjs6Eekjn8AnrWbmVQr+CBCuGU9MrxpSSzNDK/awryo3NwepOWAZw9eqk
BBCVwGBbJQx5YrdgkGC0pDq2sNzcpW/VVB3vFsmOxd9eHblnuKSIxEsCCXTtyqIt
XrLpQ1UhvI4yu102fDNhuFw2EfpzXm+K0Lc0x6idSkdM/p7SyeOxiv8hD4aMr6+G
bGUQuMl4edKZFOWFigzr8NovQAvDHZGrwfihu2cLRYKLhV97QuWVmafv/yYfXcz2
drr+wQCDNzDOXyANnssmviazrhOX0QmTAhbIXGGX/kTxYKcfPi83ZLoI3A==
=ISud
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"Much x86 work was pushed out to 5.12, but ARM more than made up for it.
ARM:
- PSCI relay at EL2 when "protected KVM" is enabled
- New exception injection code
- Simplification of AArch32 system register handling
- Fix PMU accesses when no PMU is enabled
- Expose CSV3 on non-Meltdown hosts
- Cache hierarchy discovery fixes
- PV steal-time cleanups
- Allow function pointers at EL2
- Various host EL2 entry cleanups
- Simplification of the EL2 vector allocation
s390:
- memcg accouting for s390 specific parts of kvm and gmap
- selftest for diag318
- new kvm_stat for when async_pf falls back to sync
x86:
- Tracepoints for the new pagetable code from 5.10
- Catch VFIO and KVM irqfd events before userspace
- Reporting dirty pages to userspace with a ring buffer
- SEV-ES host support
- Nested VMX support for wait-for-SIPI activity state
- New feature flag (AVX512 FP16)
- New system ioctl to report Hyper-V-compatible paravirtualization features
Generic:
- Selftest improvements"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (171 commits)
KVM: SVM: fix 32-bit compilation
KVM: SVM: Add AP_JUMP_TABLE support in prep for AP booting
KVM: SVM: Provide support to launch and run an SEV-ES guest
KVM: SVM: Provide an updated VMRUN invocation for SEV-ES guests
KVM: SVM: Provide support for SEV-ES vCPU loading
KVM: SVM: Provide support for SEV-ES vCPU creation/loading
KVM: SVM: Update ASID allocation to support SEV-ES guests
KVM: SVM: Set the encryption mask for the SVM host save area
KVM: SVM: Add NMI support for an SEV-ES guest
KVM: SVM: Guest FPU state save/restore not needed for SEV-ES guest
KVM: SVM: Do not report support for SMM for an SEV-ES guest
KVM: x86: Update __get_sregs() / __set_sregs() to support SEV-ES
KVM: SVM: Add support for CR8 write traps for an SEV-ES guest
KVM: SVM: Add support for CR4 write traps for an SEV-ES guest
KVM: SVM: Add support for CR0 write traps for an SEV-ES guest
KVM: SVM: Add support for EFER write traps for an SEV-ES guest
KVM: SVM: Support string IO operations for an SEV-ES guest
KVM: SVM: Support MMIO for an SEV-ES guest
KVM: SVM: Create trace events for VMGEXIT MSR protocol processing
KVM: SVM: Create trace events for VMGEXIT processing
...
Conflict resolution gone astray results in the kernel not booting
on VHE-capable HW when VHE support is disabled. Thankfully spotted
by David.
Reported-by: David Brazdil <dbrazdil@google.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
When a CPU is booted in EL2, the kernel checks for VHE support and
initializes the CPU core accordingly. For nVHE it also installs the stub
vectors and drops down to EL1.
Once KVM gains the ability to boot cores without going through the
kernel entry point, it will need to initialize the CPU the same way.
Extract the relevant bits of el2_setup into an init_el2_state macro
with an argument specifying whether to initialize for VHE or nVHE.
The following ifdefs are removed:
* CONFIG_ARM_GIC_V3 - always selected on arm64
* CONFIG_COMPAT - hstr_el2 can be set even without 32-bit support
No functional change intended. Size of el2_setup increased by
148 bytes due to duplication.
Signed-off-by: David Brazdil <dbrazdil@google.com>
[maz: reworked to fit the new PSTATE initial setup code]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20201202184122.26046-9-dbrazdil@google.com
As with SCTLR_ELx and other control registers, some PSTATE bits are
UNKNOWN out-of-reset, and we may not be able to rely on hardware or
firmware to initialize them to our liking prior to entry to the kernel,
e.g. in the primary/secondary boot paths and return from idle/suspend.
It would be more robust (and easier to reason about) if we consistently
initialized PSTATE to a default value, as we do with control registers.
This will ensure that the kernel is not adversely affected by bits it is
not aware of, e.g. when support for a feature such as PAN/UAO is
disabled.
This patch ensures that PSTATE is consistently initialized at boot time
via an ERET. This is not intended to relax the existing requirements
(e.g. DAIF bits must still be set prior to entering the kernel). For
features detected dynamically (which may require system-wide support),
it is still necessary to subsequently modify PSTATE.
As ERET is not always a Context Synchronization Event, an ISB is placed
before each exception return to ensure updates to control registers have
taken effect. This handles the kernel being entered with SCTLR_ELx.EOS
clear (or any future control bits being in an UNKNOWN state).
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201113124937.20574-6-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Let's make SCTLR_ELx initialization a bit clearer by using meaningful
names for the initialization values, following the same scheme for
SCTLR_EL1 and SCTLR_EL2.
These definitions will be used more widely in subsequent patches.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201113124937.20574-5-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
For a while now el2_setup has performed some basic initialization of EL1
even when the kernel is booted at EL1, so the name is a little
misleading. Further, some comments are stale as with VHE it doesn't drop
the CPU to EL1.
To clarify things, rename el2_setup to init_kernel_el, and update
comments to be clearer as to the function's purpose.
There should be no functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201113124937.20574-4-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Even though support for EFI boot remains entirely optional for arm64,
it is unlikely that we will ever be able to repurpose the image header
fields that the EFI loader relies on, i.e., the magic NOP at offset
0x0 and the PE header address at offset 0x3c.
So let's factor out the differences into a 'efi_signature_nop' macro and
a local symbol representing the PE header address, and move the
conditional definitions into efi-header.S, taking into account whether
CONFIG_EFI is enabled or not. While at it, switch to a signature NOP
that behaves more like a NOP, i.e., one that only clobbers the
flags.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201117124729.12642-4-ardb@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This reverts commit 353e228eb3.
Qian Cai reports that TX2 no longer boots with his .config as it appears
that task_cpu() gets instrumented and used before KASAN has been
initialised.
Although Mark has a proposed fix, let's take the safe option of reverting
this for now and sorting it out properly later.
Link: https://lore.kernel.org/r/711bc57a314d8d646b41307008db2845b7537b3d.camel@redhat.com
Reported-by: Qian Cai <cai@redhat.com>
Tested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Late patches for 5.10: MTE selftests, minor KCSAN preparation and removal
of some unused prototypes.
(Amit Daniel Kachhap and others)
* for-next/late-arrivals:
arm64: random: Remove no longer needed prototypes
arm64: initialize per-cpu offsets earlier
kselftest/arm64: Check mte tagged user address in kernel
kselftest/arm64: Verify KSM page merge for MTE pages
kselftest/arm64: Verify all different mmap MTE options
kselftest/arm64: Check forked child mte memory accessibility
kselftest/arm64: Verify mte tag inclusion via prctl
kselftest/arm64: Add utilities and a test to validate mte memory
The current initialization of the per-cpu offset register is difficult
to follow and this initialization is not always early enough for
upcoming instrumentation with KCSAN, where the instrumentation callbacks
use the per-cpu offset.
To make it possible to support KCSAN, and to simplify reasoning about
early bringup code, let's initialize the per-cpu offset earlier, before
we run any C code that may consume it. To do so, this patch adds a new
init_this_cpu_offset() helper that's called before the usual
primary/secondary start functions. For consistency, this is also used to
re-initialize the per-cpu offset after the runtime per-cpu areas have
been allocated (which can change CPU0's offset).
So that init_this_cpu_offset() isn't subject to any instrumentation that
might consume the per-cpu offset, it is marked with noinstr, preventing
instrumentation.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20201005164303.21389-1-mark.rutland@arm.com
Signed-off-by: Will Deacon <will@kernel.org>
TEXT_OFFSET serves no purpose, and for this reason, it was redefined
as 0x0 in the v5.8 timeframe. Since this does not appear to have caused
any issues that require us to revisit that decision, let's get rid of the
macro entirely, along with any references to it.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Link: https://lore.kernel.org/r/20200825135440.11288-1-ardb@kernel.org
Signed-off-by: Will Deacon <will@kernel.org>
The replacement of <asm/pgrable.h> with <linux/pgtable.h> made the include
of the latter in the middle of asm includes. Fix this up with the aid of
the below script and manual adjustments here and there.
import sys
import re
if len(sys.argv) is not 3:
print "USAGE: %s <file> <header>" % (sys.argv[0])
sys.exit(1)
hdr_to_move="#include <linux/%s>" % sys.argv[2]
moved = False
in_hdrs = False
with open(sys.argv[1], "r") as f:
lines = f.readlines()
for _line in lines:
line = _line.rstrip('
')
if line == hdr_to_move:
continue
if line.startswith("#include <linux/"):
in_hdrs = True
elif not moved and in_hdrs:
moved = True
print hdr_to_move
print line
Signed-off-by: Mike Rapoport <rppt@linux.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Cain <bcain@codeaurora.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Chris Zankel <chris@zankel.net>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Greg Ungerer <gerg@linux-m68k.org>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Mark Salter <msalter@redhat.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Nick Hu <nickhu@andestech.com>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vincent Chen <deanbo422@gmail.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Will Deacon <will@kernel.org>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Link: http://lkml.kernel.org/r/20200514170327.31389-4-rppt@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
