Clarify the content of the r9a06g032_clkdesc structure by naming the
remaining anonymous structures defined inside. Renaming each field and
updating the doc then becomes necessary in order to avoid name
duplications and kdoc warnings.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230913203805.465780-2-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Mention the 'dual' structure in the kdoc. This fixes the following
W=1 warning during build:
> drivers/clk/renesas/r9a06g032-clocks.c:119: warning: Function parameter or member 'dual' not described in 'r9a06g032_clkdesc'
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309101314.kTRoxND5-lkp@intel.com/
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230913203805.465780-1-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Use for_each_compatible_node() instead of open-coding it.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230802091920.3270703-1-yangyingliang@huawei.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The Renesas r9a06g032 bitselect clock implements a mux with a set_parent
hook, but doesn't provide a determine_rate implementation.
This is a bit odd, since set_parent() is there to, as its name implies,
change the parent of a clock. However, the most likely candidates to
trigger that parent change are either the assigned-clock-parents device
tree property or a call to clk_set_rate(), with determine_rate()
figuring out which parent is the best suited for a given rate.
The other trigger would be a call to clk_set_parent(), but it's far less
used, and it doesn't look like there's any obvious user for that clock.
Similarly, it doesn't look like the device tree using that clock driver
uses any of the assigned-clock properties on that clock.
So, the set_parent hook is effectively unused, possibly because of an
oversight. However, it could also be an explicit decision by the
original author to avoid any reparenting but through an explicit call to
clk_set_parent().
The latter case would be equivalent to setting the determine_rate
implementation to clk_hw_determine_rate_no_reparent(). Indeed, if no
determine_rate implementation is provided, clk_round_rate() (through
clk_core_round_rate_nolock()) will call itself on the parent if
CLK_SET_RATE_PARENT is set, and will not change the clock rate
otherwise.
And if it was an oversight, then we are at least explicit about our
behavior now and it can be further refined down the line.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: linux-renesas-soc@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20221018-clk-range-checks-fixes-v4-31-971d5077e7d2@cerno.tech
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Each entry in the clock table specifies a number of individual bits in
registers, for contolling clock reset, gaiting, etc. These reg/bit were
packed into a u16 to save space. The combined value is difficult to
understand when reviewing the clock table entries.
Introduce a "struct regbit" which still occupies only 16 bits, but
allows the register and bit values to be specified explicitly. Convert
all previous uses of u16 for reg/bit into "struct regbit".
The bulk of this patch converts the clock table to use struct regbit,
making use of the RB() helper macro. The conversion was automated by
script, and as a further verification, the compiled binary of the table
was compared before/after the change (with objdump -D).
The clk_rdesc_set() function now checks for zero reg/bit internally.
This allows callers of that function to remove those checks.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230301215520.828455-5-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Drop three unused fields from the clock descriptor structure, and update
the macros for filling such structures accordingly.
The values for such fields are kept in the source code, now unused, in
case they are needed later.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230301215520.828455-3-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Several small readability improvements:
- Move enum gate_type definition up and add comments to each field.
- Use this enum instead of generic uint32_t type in clock desc struct.
- Tidy up bitfield syntax and comments in clock desc structure
- Reformat macros for building clock desc to have one assignment per line
There is no functional change.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230301215520.828455-2-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The CFG_USB[H2MODE] allows to switch the USB configuration. The
configuration supported are:
- One host and one device
or
- Two hosts
Set CFG_USB[H2MODE] based on the USBF controller (USB device)
availability.
Signed-off-by: Herve Codina <herve.codina@bootlin.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230105152257.310642-3-herve.codina@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If condition (clkspec.np != pd->dev.of_node) is true, then the driver
ends up in an endless loop, forever, locking up the machine.
Fixes: aad03a66f9 ("clk: renesas: r9a06g032: Add clock domain support")
Reviewed-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Gareth Williams <gareth.williams.jx@renesas.com>
Link: https://lore.kernel.org/r/20221028113834.7496-1-marex@denx.de
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
There are two UART clock groups, each having a mux to select its
upstream clock source. The register/bit definitions for accessing these
two muxes appear to have been reversed since introduction. Correct them
so as to match the hardware manual.
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Phil Edworthy <phil.edworthy@renesas.com>
Link: https://lore.kernel.org/r/20220518182527.1693156-1-ralph.siemsen@linaro.org
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
New support:
- Tegra gpcdma Driver support
- Qualcomm SM8350, Sm8450 and SC7280 Device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- Deprecate '#dma-channels' & '#dma-requests' bindings
- Driver updates for stm32, ptdma idsx etc
-----BEGIN PGP SIGNATURE-----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=ANxH
-----END PGP SIGNATURE-----
Merge tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine
Pull dmaengine updates from Vinod Koul:
"Nothing special, this includes a couple of new device support and new
driver support and bunch of driver updates.
New support:
- Tegra gpcdma driver support
- Qualcomm SM8350, Sm8450 and SC7280 device support
- Renesas RZN1 dma and platform support
Updates:
- stm32 device pause/resume support and updates
- DMA memset ops Documentation and usage clarification
- deprecate '#dma-channels' & '#dma-requests' bindings
- driver updates for stm32, ptdma idsx etc"
* tag 'dmaengine-5.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/vkoul/dmaengine: (87 commits)
dmaengine: idxd: make idxd_wq_enable() return 0 if wq is already enabled
dmaengine: sun6i: Add support for the D1 variant
dmaengine: sun6i: Add support for 34-bit physical addresses
dmaengine: sun6i: Do not use virt_to_phys
dt-bindings: dma: sun50i-a64: Add compatible for D1
dmaengine: tegra: Remove unused switch case
dmaengine: tegra: Fix uninitialized variable usage
dmaengine: stm32-dma: add device_pause/device_resume support
dmaengine: stm32-dma: rename pm ops before dma pause/resume introduction
dmaengine: stm32-dma: pass DMA_SxSCR value to stm32_dma_handle_chan_done()
dmaengine: stm32-dma: introduce stm32_dma_sg_inc to manage chan->next_sg
dmaengine: stm32-dmamux: avoid reset of dmamux if used by coprocessor
dmaengine: qcom: gpi: Add support for sc7280
dt-bindings: dma: pl330: Add power-domains
dmaengine: stm32-mdma: use dev_dbg on non-busy channel spurious it
dmaengine: stm32-mdma: fix chan initialization in stm32_mdma_irq_handler()
dmaengine: stm32-mdma: remove GISR1 register
dmaengine: ti: deprecate '#dma-channels'
dmaengine: mmp: deprecate '#dma-channels'
dmaengine: pxa: deprecate '#dma-channels' and '#dma-requests'
...
The clock controller device on r9a06g032 takes all the memory range that
is described as being a system controller. This range contains many
different (unrelated?) registers besides the ones belonging to the clock
controller, that can necessitate to be accessed from other peripherals.
For instance, the dmamux registers are there. The dmamux "device" will
be described as a child node of the clock/system controller node, which
means we need the top device driver (the clock controller driver in this
case) to populate its children manually. In case of error when
populating the children, we do not fail the probe on purpose to keep the
clk driver up and running.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-7-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
The dmamux register is located within the system controller.
Without syscon, we need an extra helper in order to give write access to
this register to a dmamux driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20220427095653.91804-5-miquel.raynal@bootlin.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
It needs to be un-gated, but also a reset must be released and an idle
flag should also be disabled.
The driver already supports all these operations, so update the
description of the RTC hclock to fit these requirements.
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20220421090016.79517-3-miquel.raynal@bootlin.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
As the .round_rate() callback returns a long clock rate, it cannot
return clock rates that do not fit in signed long, but do fit in
unsigned long. Hence switch the divider clocks on RZ/N1 from the old
.round_rate() callback to the newer .determine_rate() callback, which
does not suffer from this limitation.
Note that range checking is not yet implemented.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/7a384d02b85cdaac4a0e2b357582c8244b9a6f98.1617282116.git.geert+renesas@glider.be
As clk_core_populate_parent_map() checks clk_init_data.num_parents
first, and checks clk_init_data.parent_names[] before
clk_init_data.parent_data[] and clk_init_data.parent_hws[], leaving the
latter uninitialized doesn't do harm for now. However, it is better to
play it safe, and initialize all clk_init_data structures to zeroes, to
avoid any current and future members containing uninitialized data.
Remove a few explicit zero initializers, which are now superfluous.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lore.kernel.org/r/20210326105434.1574796-1-geert+renesas@glider.be
The R9A06G032 clock driver uses an array of packed structures to reduce
kernel size. However, this array contains pointers, which are no longer
aligned naturally, and cannot be relocated on PPC64. Hence when
compile-testing this driver on PPC64 with CONFIG_RELOCATABLE=y (e.g.
PowerPC allyesconfig), the following warnings are produced:
WARNING: 136 bad relocations
c000000000616be3 R_PPC64_UADDR64 .rodata+0x00000000000cf338
c000000000616bfe R_PPC64_UADDR64 .rodata+0x00000000000cf370
...
Fix this by dropping the __packed attribute from the r9a06g032_clkdesc
definition, trading a small size increase for portability.
This increases the 156-entry clock table by 1 byte per entry, but due to
the compiler generating more efficient code for unpacked accesses, the
net size increase is only 76 bytes (gcc 9.3.0 on arm32).
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201130085743.1656317-1-geert+renesas@glider.be
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # PowerPC allyesconfig build
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
This file seems to be for R9A06G032 only. So replace reference to
R9A09G032 by R9A06G032 to avoid confusion.
AFAIK, R9A09G032 does'nt exist.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/20200413041709.3630-1-christophe.jaillet@wanadoo.fr
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The RZ/N1 Clock Domain driver does not implement the
generic_pm_domain.power_{on,off}() callbacks, as the domain itself
cannot be powered down. Hence the domain should be marked as always-on
by setting the GENPD_FLAG_ALWAYS_ON flag, to prevent the core PM Domain
code from considering it for power-off, and doing unnessary processing.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
There are several clocks on the r9a06g032 which are currently not
enabled in their drivers that can be delegated to clock domain system
for power management. Therefore add support for clock domain
functionality to the r9a06g032 clock driver.
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
The clock driver is missing support for the clk_pci_usb clock that is
present on the SoC. This is added to allow the clock to be supported.
Signed-off-by: Gareth Williams <gareth.williams.jx@renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This flag doesn't look to be used by any code, just set in various clk
init structures and then never tested again. Remove it from these
drivers as it doesn't provide any benefit.
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: <linux-renesas-soc@vger.kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
The clock for UARTs 0 through 2 is UART012, the clock for UARTs 3 through
7 is UART34567.
For UART012, we stop the clock driver from changing the clock rate. This
is because the Synopsys UART driver simply sets the reference clock to 16x
the baud rate, but doesn't check if the actual rate is within the required
tolerance. The RZ/N1 clock divider can't provide this (we have to rely on
the UART's internal divider to set the correct clock rate), so you end up
with a clock rate that is way off what you wanted.
In addition, since the clock is shared between multiple UARTs, you don't
want the driver trying to change the clock rate as it may affect the other
UARTs (which may not have been configured yet, so you don't know what baud
rate they will use). Normally, the clock rate is set early on before Linux
to some very high rate that supports all of the clock rates you want.
This change stops the UART34567 clock rate from changing for the same
reasons.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Fixes: 4c3d88526e ("clk: renesas: Renesas R9A06G032 clock driver")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This provides a clock driver for the Renesas R09A06G032.
This uses a structure derived from both the R-Car Gen2 driver as well as
the renesas-cpg-mssr driver.
Signed-off-by: Michel Pollet <michel.pollet@bp.renesas.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
