Some information showed by the dump function is invalid. Mask
the unnecessary information from the dump file.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
When dumping SQ, only the corresponding ID's SQE needs to be
dumped, and there is no need to apply for the entire SQE
memory. This is because excessive dump operations can lead to
memory resource waste.
Therefor apply for the space corresponding to sqe_id separately
to avoid space waste.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
There is a scenario where the file directory is created but the
file attribute is not set. In this case, if a user accesses the
file, an error occurs.
So adjust the processing logic in the debugfs creation to
prevent the file from being accessed before the file attributes
such as the index are set.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
During the zip probe process, the debugfs failure does not stop
the probe. When debugfs initialization fails, jumping to the
error branch will also release regs, in addition to its own
rollback operation.
As a result, it may be released repeatedly during the regs
uninit process. Therefore, the null check needs to be added to
the regs uninit process.
Signed-off-by: Chenghai Huang <huangchenghai2@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The debugfs files 'dev_state' and 'dev_timeout' are added.
Users can query the current queue stop status through these two
files. And set the waiting timeout when the queue is released.
dev_state: if dev_timeout is set, dev_state indicates the status
of stopping the queue. 0 indicates that the queue is stopped
successfully. Other values indicate that the queue stops fail.
If dev_timeout is not set, the value of dev_state is 0;
dev_timeout: if the queue fails to stop, the queue is released
after waiting dev_timeout * 20ms.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Read the values of some device registers before the device
is reset, these values help analyze the cause of the device exception.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Support get device current state. The value 0 indicates that
the device is busy, and the value 1 indicates that the
device is idle. When the device is in suspended, 1 is returned.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The 'QM_INIT' and 'QM_CLOSE' status of qm and 'QP_INIT'
and 'QP_CLOSE' status of queue are not actually used. Currently,
driver only needs to switch status when the device or queue
is enabled or stopped, Therefore, remove unneeded status to
simplify driver. In addition, rename'QM_START to'QM_WORK' for
ease to understand.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The 'offset' type is unsigned long in 'struct debugfs_reg32',
so type of values casts to unsigned long long is incorrect, and the
values do not require type cast, remove them.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
If the temporarily applied memory is used to set or get the xqc
information, the driver releases the memory immediately after the
hardware mailbox operation time exceeds the driver waiting time.
However, the hardware does not cancel the operation, so the hardware
may write data to released memory.
Therefore, when the driver is bound to a device, the driver reserves
memory for the xqc configuration. The subsequent xqc configuration
uses the reserved memory to prevent hardware from accessing the
released memory.
Signed-off-by: Weili Qian <qianweili@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reduce the function complexity by use the function table in the
process of dumping queue. The function input parameters are
unified. And maintainability is enhanced.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Considering that the qm feature and debugfs feature are independent.
The code related to debugfs is getting larger and larger. It should be
separate as a debugfs file. So move some debugfs code to new file from
qm file. The qm code logic is not modified. And maintainability is
enhanced.
Signed-off-by: Kai Ye <yekai13@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
