The kernel test robot reported a build failure:
or1k-linux-ld: drivers/net/dsa/realtek/realtek-smi.o:(.rodata+0x16c): undefined reference to `rtl8366rb_variant'
... with the following build configuration:
CONFIG_NET_DSA_REALTEK=y
CONFIG_NET_DSA_REALTEK_SMI=y
CONFIG_NET_DSA_REALTEK_RTL8365MB=y
CONFIG_NET_DSA_REALTEK_RTL8366RB=m
The problem here is that the realtek-smi interface driver gets built-in,
while the rtl8366rb switch subdriver gets built as a module, hence the
symbol rtl8366rb_variant is not reachable when defining the OF device
table in the interface driver.
The Kconfig dependencies don't help in this scenario because they just
say that the subdriver(s) depend on at least one interface driver. In
fact, the subdrivers don't depend on the interface drivers at all, and
can even be built even in their absence. Somewhat strangely, the
interface drivers can also be built in the absence of any subdriver,
BUT, if a subdriver IS enabled, then it must be reachable according to
the linkage of the interface driver: effectively what the IS_REACHABLE()
macro achieves. If it is not reachable, the above kind of linker error
will be observed.
Rather than papering over the above build error by simply using
IS_REACHABLE(), we can do a little better and admit that it is actually
the interface drivers that have a dependency on the subdrivers. So this
patch does exactly that. Specifically, we ensure that:
1. The interface drivers' Kconfig symbols must have a value no greater
than the value of any subdriver Kconfig symbols.
2. The subdrivers should by default enable both interface drivers, since
most users probably want at least one of them; those interface
drivers can be explicitly disabled however.
What this doesn't do is prevent a user from building only a subdriver,
without any interface driver. To that end, add an additional line of
help in the menu to guide users in the right direction.
Link: https://lore.kernel.org/all/202204110757.XIafvVnj-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Fixes: aac9400106 ("net: dsa: realtek: add new mdio interface for drivers")
Signed-off-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mt7530 driver does not make use of the speed, duplex, pause or
advertisement in its phylink_mac_config() implementation, so it can be
marked as a non-legacy driver.
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Move the autoneg bit handling to the PCS validation, which allows us to
get rid of mt753x_phylink_validate() and rely on the default
phylink_generic_validate() implementation for the MAC side.
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Partially convert the mt7530 driver to use phylink's PCS support. This
is a partial implementation as we don't move anything into the
pcs_config method yet - this driver supports SGMII or 1000BASE-X
without in-band.
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Switch mt7530 to use phylink_get_linkmodes() to generate the ethtool
linkmodes that can be supported. We are unable to use the generic
helper for this as pause modes are dependent on the interface as
the Autoneg bit depends on the interface mode.
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that mt7530 is not using the basex helper, it becomes unnecessary to
indicate support for both 1000baseX and 2500baseX when one of the 803.3z
PHY interface modes is being selected. Ensure that the driver indicates
only those linkmodes that can actually be supported by the PHY interface
mode.
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Now that we have a better method to select SFP interface modes, we
no longer need to use phylink_helper_basex_speed() in a driver's
validation function.
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
As phylink checks the interface mode against the supported_interfaces
bitmap, we no longer need to validate the interface mode, nor handle
PHY_INTERFACE_MODE_NA in the validation function. Remove these to
simplify the implementation.
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Populate the supported interfaces and MAC capabilities for mt7530,
mt7531 and mt7621 DSA switches. Filling this in will enable phylink
to pre-check the PHY interface mode against the the supported
interfaces bitmap prior to calling the validate function, and will
eventually allow us to convert to using the generic validation.
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When using an external PHY connected using RGMII to mt7531 port 5, the
PHY can be used to used support 1000BASE-X connections. Moreover, if
1000BASE-T is supported, then we should allow 1000BASE-X as well, since
which are supported is a property of the PHY.
Therefore, it makes no sense to exclude this from the linkmodes when
1000BASE-T is supported.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The DSA master might not have been probed yet in which case the probe of
the felix switch fails with -EPROBE_DEFER:
[ 4.435305] mscc_felix 0000:00:00.5: Failed to register DSA switch: -517
It is not an error. Use dev_err_probe() to demote this particular error
to a debug message.
Fixes: 5605194877 ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220408101521.281886-1-michael@walle.cc
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
As the possible failure of the allocation, kzalloc() may return NULL
pointer.
Therefore, it should be better to check the 'sgi' in order to prevent
the dereference of NULL pointer.
Fixes: 23ae3a7877 ("net: dsa: felix: add stream gate settings for psfp").
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220329090800.130106-1-zhengyongjun3@huawei.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The bug is here:
return rule;
The list iterator value 'rule' will *always* be set and non-NULL
by list_for_each_entry(), so it is incorrect to assume that the
iterator value will be NULL if the list is empty or no element
is found.
To fix the bug, return 'rule' when found, otherwise return NULL.
Fixes: ae7a5aff78 ("net: dsa: bcm_sf2: Keep copy of inserted rules")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Xiaomeng Tong <xiam0nd.tong@gmail.com>
Link: https://lore.kernel.org/r/20220328032431.22538-1-xiam0nd.tong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Some chips using the split VTU/STU design will not accept VTU entries
who's SID points to an invalid STU entry. Therefore, mark all those
chips with either the mv88e6352_g1_stu_* or mv88e6390_g1_stu_* ops as
appropriate.
Notably, chips for the Opal Plus (6085/6097) era seem to use a
different implementation than those from Agate (6352) and onwards,
even though their external interface is the same. The former happily
accepts VTU entries referencing invalid STU entries, while the latter
does not.
This fixes an issue where the driver would fail to probe switch trees
that contained chips of the Agate/Topaz generation which did not
declare STU support, as loaded VTU entries would be read back as
invalid.
Fixes: 49c98c1dc7 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/r/20220319110345.555270-1-tobias@waldekranz.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the same way that we check for STU support in the MST state
callback, we should also verify it before trying to change a VLANs
MSTI membership.
Fixes: acaf4d2e36 ("net: dsa: mv88e6xxx: MST Offloading")
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Simply having a physical STU table in the device doesn't do us any
good if there's no implementation of the relevant ops to access that
table. So ensure that chips that claim STU support can also talk to
the hardware.
This fixes an issue where chips that had a their ->info->max_sid
set (due to their family membership), but no implementation (due to
their chip-specific ops struct) would fail to probe.
Fixes: 49c98c1dc7 ("net: dsa: mv88e6xxx: Disentangle STU from VTU")
Reported-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Marek Behún <kabel@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Gain support for port mirroring using tc-matchall by forwarding the
calls to the ocelot switch library.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Drivers might have error messages to propagate to user space, most
common being that they support a single mirror port.
Propagate the netlink extack so that they can inform user space in a
verbal way of their limitations.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allocate a SID in the STU for each MSTID in use by a bridge and handle
the mapping of MSTIDs to VLANs using the SID field of each VTU entry.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Export the raw STU data in a devlink region so that it can be
inspected from userspace and compared to the current bridge
configuration.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In early LinkStreet silicon (e.g. 6095/6185), the per-VLAN STP states
were kept in the VTU - there was no concept of a SID. Later, the
information was split into two tables, where the VTU only tracked
memberships and deferred the STP state tracking to the STU via a
pointer (SID). This meant that a group of VLANs could share the same
STU entry. Most likely, this was done to align with MSTP (802.1Q-2018,
Clause 13), which is built on this principle.
While the VTU is still 4k lines on most devices, the STU is capped at
64 entries. This means that the current stategy, updating STU info
whenever a VTU entry is updated, can not easily support MSTP because:
- The maximum number of VIDs would also be capped at 64, as we would
have to allocate one SID for every VTU entry - even if many VLANs
would effectively share the same MST.
- MSTP updates would be unnecessarily slow as you would have to
iterate over all VLANs that share the same MST.
In order to support MSTP offloading in the future, manage the STU as a
separate entity from the VTU.
Only add support for newer hardware with separate VTU and
STU. VTU-only devices can also be supported, but essentially this
requires a software implementation of an STU (fanning out state
changed to all VLANs tied to the same MST).
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Follow the established programming model for this driver and provide
shims in the felix DSA driver which call the implementations from the
ocelot switch lib. The ocelot switchdev driver wasn't integrated with
dcbnl due to lack of hardware availability.
The switch doesn't have any fancy QoS classification enabled by default.
The provided getters will create a default-prio app table entry of 0,
and no dscp entry. However, the getters have been made to actually
retrieve the hardware configuration rather than static values, to be
future proof in case DSA will need this information from more call paths.
For default-prio, there is a single field per port, in ANA_PORT_QOS_CFG,
called QOS_DEFAULT_VAL.
DSCP classification is enabled per-port, again via ANA_PORT_QOS_CFG
(field QOS_DSCP_ENA), and individual DSCP values are configured as
trusted or not through register ANA_DSCP_CFG (replicated 64 times).
An untrusted DSCP value falls back to other QoS classification methods.
If trusted, the selected ANA_DSCP_CFG register also holds the QoS class
in the QOS_DSCP_VAL field.
The hardware also supports DSCP remapping (DSCP value X is translated to
DSCP value Y before the QoS class is determined based on the app table
entry for Y) and DSCP packet rewriting. The dcbnl framework, for being
so flexible in other useless areas, doesn't appear to support this.
So this functionality has been left out.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add spi_device_id tables to avoid logs like "SPI driver ksz9477-switch
has no spi_device_id".
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This enables non-standard MTUs on a per-port basis, with the overall
frame size set based on the CPU port.
When the MTU is not changed, this should have no effect.
Long packets crash the switch with MTUs of greater than 2526, so the
maximum is limited for now. Medium packets are sometimes dropped (e.g.
TCP over 2477, UDP over 2516-2519, ICMP over 2526), Hence an MTU value
of 2400 seems safe.
Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
Signed-off-by: Aleksander Jan Bajkowski <olek2@wp.pl>
Link: https://lore.kernel.org/r/20220308230457.1599237-1-olek2@wp.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This chips supports two ways to configure max MTU size:
- by setting SW_LEGAL_PACKET_DISABLE bit: if this bit is 0 allowed packed size
will be between 64 and bytes 1518. If this bit is 1, it will accept
packets up to 2000 bytes.
- by setting SW_JUMBO_PACKET bit. If this bit is set, the chip will
ignore SW_LEGAL_PACKET_DISABLE value and use REG_SW_MTU__2 register to
configure MTU size.
Current driver has disabled SW_JUMBO_PACKET bit and activates
SW_LEGAL_PACKET_DISABLE. So the switch will pass all packets up to 2000 without
any way to configure it.
By providing port_change_mtu we are switch to SW_JUMBO_PACKET way and will
be able to configure MTU up to ~9000.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://lore.kernel.org/r/20220308135857.1119028-1-o.rempel@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The Felix driver declares FDB isolation but puts all standalone ports in
VID 0. This is mostly problem-free as discussed with Alvin here:
https://patchwork.kernel.org/project/netdevbpf/cover/20220302191417.1288145-1-vladimir.oltean@nxp.com/#24763870
however there is one catch. DSA still thinks that FDB entries are
installed on the CPU port as many times as there are user ports, and
this is problematic when multiple user ports share the same MAC address.
Consider the default case where all user ports inherit their MAC address
from the DSA master, and then the user runs:
ip link set swp0 address 00:01:02:03:04:05
The above will make dsa_slave_set_mac_address() call
dsa_port_standalone_host_fdb_add() for 00:01:02:03:04:05 in port 0's
standalone database, and dsa_port_standalone_host_fdb_del() for the old
address of swp0, again in swp0's standalone database.
Both the ->port_fdb_add() and ->port_fdb_del() will be propagated down
to the felix driver, which will end up deleting the old MAC address from
the CPU port. But this is still in use by other user ports, so we end up
breaking unicast termination for them.
There isn't a problem in the fact that DSA keeps track of host
standalone addresses in the individual database of each user port: some
drivers like sja1105 need this. There also isn't a problem in the fact
that some drivers choose the same VID/FID for all standalone ports.
It is just that the deletion of these host addresses must be delayed
until they are known to not be in use any longer, and only the driver
has this knowledge. Since DSA keeps these addresses in &cpu_dp->fdbs and
&cpu_db->mdbs, it is just a matter of walking over those lists and see
whether the same MAC address is present on the CPU port in the port db
of another user port.
I have considered reusing the generic dsa_port_walk_fdbs() and
dsa_port_walk_mdbs() schemes for this, but locking makes it difficult.
In the ->port_fdb_add() method and co, &dp->addr_lists_lock is held, but
dsa_port_walk_fdbs() also acquires that lock. Also, even assuming that
we introduce an unlocked variant of the address iterator, we'd still
need some relatively complex data structures, and a void *ctx in the
dsa_fdb_walk_cb_t which we don't currently pass, such that drivers are
able to figure out, after iterating, whether the same MAC address is or
isn't present in the port db of another port.
All the above, plus the fact that I expect other drivers to follow the
same model as felix where all standalone ports use the same FID, made me
conclude that a generic method provided by DSA is necessary:
dsa_fdb_present_in_other_db() and the mdb equivalent. Felix calls this
from the ->port_fdb_del() handler for the CPU port, when the database
was classified to either a port db, or a LAG db.
For symmetry, we also call this from ->port_fdb_add(), because if the
address was installed once, then installing it a second time serves no
purpose: it's already in hardware in VID 0 and it affects all standalone
ports.
This change moves dsa_db_equal() from switch.c to dsa.c, since it now
has one more caller.
Fixes: 54c3198460 ("net: mscc: ocelot: enforce FDB isolation when VLAN-unaware")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two blamed commits were written/tested individually but not
together.
When put together, commit 90897569be ("net: dsa: felix: start off with
flooding disabled on the CPU port"), which deletes a reinitialization of
PGID_UC/PGID_MC/PGID_BC, is no longer sufficient to ensure that these
port masks don't contain the CPU port module.
This is because commit b903a6bd2e ("net: dsa: felix: migrate flood
settings from NPI to tag_8021q CPU port") overwrites the hardware
default settings towards the CPU port module with the settings that used
to be present on the NPI port treated as a regular port. There, flooding
is enabled, so flooding would get enabled on the CPU port module too.
Adding conditional logic somewhere within felix_setup_tag_npi() to
configure either the default no-flood policy or the flood policy
inherited from the tag_8021q CPU port from a previous call to
dsa_port_manage_cpu_flood() is getting complicated. So just let the
migration logic do its thing during initial setup (which will
temporarily turn on flooding), then turn flooding off for the NPI port
after felix_set_tag_protocol() finishes. Here we are in felix_setup(),
so the DSA slave interfaces are not yet created, and this doesn't affect
traffic in any way.
Fixes: 90897569be ("net: dsa: felix: start off with flooding disabled on the CPU port")
Fixes: b903a6bd2e ("net: dsa: felix: migrate flood settings from NPI to tag_8021q CPU port")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We no longer need the workaround in the felix driver to avoid calling
dsa_port_walk_fdbs() when &dp->fdbs is an uninitialized list, because
that list is now initialized from all call paths of felix_set_tag_protocol().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Discussing one of the tests in mt753x_phylink_validate() with Landen
Chao confirms that the "||" should be "&&". Fix this.
Fixes: c288575f78 ("net: dsa: mt7530: Add the support of MT7531 switch")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://lore.kernel.org/r/E1nRCF0-00CiXD-7q@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The trailing tag is also supported by this family. The default is still
rtl8_4 but now the switch supports changing the tag to rtl8_4t.
Reintroduce the dropped cpu in struct rtl8365mb (removed by 6147631).
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Reviewed-by: Alvin Šipraga <alsi@bang-olufsen.dk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit
baebdf48c3 ("net: dev: Makes sure netif_rx() can be invoked in any context.")
the function netif_rx() can be used in preemptible/thread context as
well as in interrupt context.
Use netif_rx().
Cc: Kurt Kanzenbach <kurt@linutronix.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Kurt Kanzenbach <kurt@linutronix.de> # hellcreek
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to an apparently incorrect conflict resolution on my part in commit
54c3198460 ("net: mscc: ocelot: enforce FDB isolation when
VLAN-unaware"), "ocelot->ports[port]->is_dsa_8021q_cpu = false" was
supposed to be replaced by "ocelot_port_unset_dsa_8021q_cpu(ocelot, port)"
which does the same thing, and more. But now we have both, so the direct
assignment is redundant. Remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packet extraction failures over register-based MMIO are silent, and
difficult to pinpoint. Add an error message to remedy this.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automated tools complain that felix_check_xtr_pkt() has logic to drain
the CPU queue on the reception of a PTP packet over Ethernet, yet it
returns an uninitialized error code in the case where the CPU queue was
empty.
This is not likely to happen (/possible if hardware works correctly),
but it isn't a fatal condition either. The PTP packet will be dequeued
from the CPU queue when the next PTP packet arrives. So initialize "err"
to 0 for the case where nothing was dequeued during this iteration.
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DSA ->port_rxtstamp() function is never called for PTP_CLASS_NONE:
dsa_skb_defer_rx_timestamp:
if (type == PTP_CLASS_NONE)
return false;
if (likely(ds->ops->port_rxtstamp))
return ds->ops->port_rxtstamp(ds, p->dp->index, skb, type);
So practically, the argument is unused, so remove it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This assignment is redundant, since ocelot->npi has already been set to
-1 by felix_npi_port_deinit(). Call path:
felix_change_tag_protocol
-> felix_del_tag_protocol(DSA_TAG_PROTO_OCELOT)
-> felix_teardown_tag_npi
-> felix_npi_port_deinit
-> felix_set_tag_protocol(DSA_TAG_PROTO_OCELOT_8021Q)
-> felix_setup_tag_8021q
-> felix_8021q_cpu_port_init
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
felix_migrate_flood_to_tag_8021q_port() takes care of clearing the
flooding bits on the old CPU port (which was the CPU port module), so
manually clearing this bit from PGID_UC, PGID_MC, PGID_BC is redundant.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver probes with all ports as standalone, and it supports unicast
filtering. So DSA will call port_fdb_add() for all necessary addresses
on the current CPU port. We also handle migrations when the CPU port
hardware resource changes (on tagging protocol change), so there should
not be any unknown address that we have to receive while not promiscuous.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the tagging protocol changes from "ocelot" to "ocelot-8021q" or in
reverse, the DSA promiscuity setting that was applied for the old CPU
port must be transferred to the new one.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ocelot" and "ocelot-8021q" tagging protocols make use of different
hardware resources, and host FDB entries have different destination
ports in the switch analyzer module, practically speaking.
So when the user requests a tagging protocol change, the driver must
migrate all host FDB and MDB entries from the NPI port (in fact CPU port
module) towards the same physical port, but this time used as a regular
port.
It is pointless for the felix driver to keep a copy of the host
addresses, when we can create and export DSA helpers for walking through
the addresses that it already needs to keep on the CPU port, for
refcounting purposes.
felix_classify_db() is moved up to avoid a forward declaration.
We pass "bool change" because dp->fdbs and dp->mdbs are uninitialized
lists when felix_setup() first calls felix_set_tag_protocol(), so we
need to avoid calling dsa_port_walk_fdbs() during probe time.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmIdBQAACgkQJNaLcl1U
h9D1GQf/dVustBx4kCUNJt4QuMF4rozHtAzo2qK1grAnpHEqiMvVEzAuxfbTgJOx
9AUj+xEuVpPxoYUDLVJpJrxwdAl0Ue8tDRgP9Cqr/o6a3IoKrhEi+1KpSbvjcsgB
oqJEcvdjk1XAtl+QXmvyMjbMLxpz2x3Ne6dj7RL/LsfxXC0/om+NQIvJBfn78Dj2
JSNJcVtRDmdaApXfguDGA0u3COarypybYMuumIO4rRxjA5S4FXXovny4nwNXvOhS
Ki5/7GKq9rojeeIf0kD/IDdkmSS0WZp3Rc2mIrdsrXrTca+dTo3sYlcP+HMcZmtW
0+bzsht6VyApfGGZ1Ra/w3NxN6OMMg==
=TyvV
-----END PGP SIGNATURE-----
Merge tag 'spi-remove-void' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Mark Brown says:
====================
spi: Make remove() return void
This series from Uwe Kleine-König converts the spi remove function to
return void since there is nothing useful that we can do with a failure
and it as more buses are converted it'll enable further work on the
driver core.
====================
Link: https://lore.kernel.org/r/20220228173957.1262628-2-broonie@kernel.org/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
All users of the felix driver were creating their own prevalidate_phy_mode
function. The same logic can be performed in a more general way by using a
simple array of bit fields.
Signed-off-by: Colin Foster <colin.foster@in-advantage.com>
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As more police parameters are passed to flow_offload, driver can check
them to make sure hardware handles packets in the way indicated by tc.
The conform-exceed control should be drop/pipe or drop/ok. Besides,
for drop/ok, the police should be the last action. As hardware can't
configure peakrate/avrate/overhead, offload should not be supported if
any of them is configured.
Signed-off-by: Jianbo Liu <jianbol@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
