Schedule service task and EXTTS in the top half to avoid bottom half
scheduling if possible, which significantly reduces timestamping delay.
Co-developed-by: Michal Michalik <michal.michalik@intel.com>
Signed-off-by: Michal Michalik <michal.michalik@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Stop dividing the phase_offset value received from firmware. This fault
is present since the initial implementation.
The phase_offset value received from firmware is in 0.01ps resolution.
Dpll subsystem is using the value in 0.001ps, raw value is adjusted
before providing it to the user.
The user can observe the value of phase offset with response to
`pin-get` netlink message of dpll subsystem for an active pin:
$ ./tools/net/ynl/cli.py --spec Documentation/netlink/specs/dpll.yaml \
--do pin-get --json '{"id":2}'
Where example of correct response would be:
{'board-label': 'C827_0-RCLKA',
'capabilities': 6,
'clock-id': 4658613174691613800,
'frequency': 1953125,
'id': 2,
'module-name': 'ice',
'parent-device': [{'direction': 'input',
'parent-id': 6,
'phase-offset': -216839550,
'prio': 9,
'state': 'connected'},
{'direction': 'input',
'parent-id': 7,
'phase-offset': -42930,
'prio': 8,
'state': 'connected'}],
'phase-adjust': 0,
'phase-adjust-max': 16723,
'phase-adjust-min': -16723,
'type': 'mux'}
Provided phase-offset value (-42930) shall be divided by the user with
DPLL_PHASE_OFFSET_DIVIDER to get actual value of -42.930 ps.
Before the fix, the response was not correct:
{'board-label': 'C827_0-RCLKA',
'capabilities': 6,
'clock-id': 4658613174691613800,
'frequency': 1953125,
'id': 2,
'module-name': 'ice',
'parent-device': [{'direction': 'input',
'parent-id': 6,
'phase-offset': -216839,
'prio': 9,
'state': 'connected'},
{'direction': 'input',
'parent-id': 7,
'phase-offset': -42,
'prio': 8,
'state': 'connected'}],
'phase-adjust': 0,
'phase-adjust-max': 16723,
'phase-adjust-min': -16723,
'type': 'mux'}
Where phase-offset value (-42), after division
(DPLL_PHASE_OFFSET_DIVIDER) would be: -0.042 ps.
Fixes: 8a3a565ff2 ("ice: add admin commands to access cgu configuration")
Fixes: 90e1c90750 ("ice: dpll: implement phase related callbacks")
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Disabling netdev with ethtool private flag "link-down-on-close" enabled
can cause NULL pointer dereference bug. Shut down VSI regardless of
"link-down-on-close" state.
Fixes: 8ac7132704 ("ice: Fix interface being down after reset with link-down-on-close flag on")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Ngai-Mint Kwan <ngai-mint.kwan@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The driver should not report an error message when for a medialess port
the link_down_on_close flag is enabled and the physical link cannot be
set down.
Fixes: 8ac7132704 ("ice: Fix interface being down after reset with link-down-on-close flag on")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Katarzyna Wieczerzycka <katarzyna.wieczerzycka@intel.com>
Signed-off-by: Wojciech Drewek <wojciech.drewek@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tony Nguyen says:
====================
intel: use bitfield operations
Jesse Brandeburg says:
After repeatedly getting review comments on new patches, and sporadic
patches to fix parts of our drivers, we should just convert the Intel code
to use FIELD_PREP() and FIELD_GET(). It's then "common" in the code and
hopefully future change-sets will see the context and do-the-right-thing.
This conversion was done with a coccinelle script which is mentioned in the
commit messages. Generally there were only a couple conversions that were
"undone" after the automatic changes because they tried to convert a
non-contiguous mask.
Patch 1 is required at the beginning of this series to fix a "forever"
issue in the e1000e driver that fails the compilation test after conversion
because the shift / mask was out of range.
The second patch just adds all the new #includes in one go.
The patch titled: "ice: fix pre-shifted bit usage" is needed to allow the
use of the FIELD_* macros and fix up the unexpected "shifts included"
defines found while creating this series.
The rest are the conversion to use FIELD_PREP()/FIELD_GET(), and the
occasional leXX_{get,set,encode}_bits() call, as suggested by Alex.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=stU2
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Alexei Starovoitov says:
====================
pull-request: bpf-next 2023-12-18
This PR is larger than usual and contains changes in various parts
of the kernel.
The main changes are:
1) Fix kCFI bugs in BPF, from Peter Zijlstra.
End result: all forms of indirect calls from BPF into kernel
and from kernel into BPF work with CFI enabled. This allows BPF
to work with CONFIG_FINEIBT=y.
2) Introduce BPF token object, from Andrii Nakryiko.
It adds an ability to delegate a subset of BPF features from privileged
daemon (e.g., systemd) through special mount options for userns-bound
BPF FS to a trusted unprivileged application. The design accommodates
suggestions from Christian Brauner and Paul Moore.
Example:
$ sudo mkdir -p /sys/fs/bpf/token
$ sudo mount -t bpf bpffs /sys/fs/bpf/token \
-o delegate_cmds=prog_load:MAP_CREATE \
-o delegate_progs=kprobe \
-o delegate_attachs=xdp
3) Various verifier improvements and fixes, from Andrii Nakryiko, Andrei Matei.
- Complete precision tracking support for register spills
- Fix verification of possibly-zero-sized stack accesses
- Fix access to uninit stack slots
- Track aligned STACK_ZERO cases as imprecise spilled registers.
It improves the verifier "instructions processed" metric from single
digit to 50-60% for some programs.
- Fix verifier retval logic
4) Support for VLAN tag in XDP hints, from Larysa Zaremba.
5) Allocate BPF trampoline via bpf_prog_pack mechanism, from Song Liu.
End result: better memory utilization and lower I$ miss for calls to BPF
via BPF trampoline.
6) Fix race between BPF prog accessing inner map and parallel delete,
from Hou Tao.
7) Add bpf_xdp_get_xfrm_state() kfunc, from Daniel Xu.
It allows BPF interact with IPSEC infra. The intent is to support
software RSS (via XDP) for the upcoming ipsec pcpu work.
Experiments on AWS demonstrate single tunnel pcpu ipsec reaching
line rate on 100G ENA nics.
8) Expand bpf_cgrp_storage to support cgroup1 non-attach, from Yafang Shao.
9) BPF file verification via fsverity, from Song Liu.
It allows BPF progs get fsverity digest.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (164 commits)
bpf: Ensure precise is reset to false in __mark_reg_const_zero()
selftests/bpf: Add more uprobe multi fail tests
bpf: Fail uprobe multi link with negative offset
selftests/bpf: Test the release of map btf
s390/bpf: Fix indirect trampoline generation
selftests/bpf: Temporarily disable dummy_struct_ops test on s390
x86/cfi,bpf: Fix bpf_exception_cb() signature
bpf: Fix dtor CFI
cfi: Add CFI_NOSEAL()
x86/cfi,bpf: Fix bpf_struct_ops CFI
x86/cfi,bpf: Fix bpf_callback_t CFI
x86/cfi,bpf: Fix BPF JIT call
cfi: Flip headers
selftests/bpf: Add test for abnormal cnt during multi-kprobe attachment
selftests/bpf: Don't use libbpf_get_error() in kprobe_multi_test
selftests/bpf: Add test for abnormal cnt during multi-uprobe attachment
bpf: Limit the number of kprobes when attaching program to multiple kprobes
bpf: Limit the number of uprobes when attaching program to multiple uprobes
bpf: xdp: Register generic_kfunc_set with XDP programs
selftests/bpf: utilize string values for delegate_xxx mount options
...
====================
Link: https://lore.kernel.org/r/20231219000520.34178-1-alexei.starovoitov@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It was found while doing further testing of the previous commit
fbf32a9bab91 ("ice: field get conversion") that one of the FIELD_GET
conversions should really be a FIELD_PREP. The previous code was styled
as a match to the FIELD_GET conversion, which always worked because the
shift value was 0. The code makes way more sense as a FIELD_PREP and
was in fact the only FIELD_GET with two constant arguments in this
series.
Didn't squash this patch to make it easier to call out the
(non-impactful) bug.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor the ice driver to use FIELD_GET() for mask and shift reads,
which reduces lines of code and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
@get@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) & mask) >> shift)
+FIELD_GET(mask, a)
and applied via:
spatch --sp-file field_prep.cocci --in-place --dir \
drivers/net/ethernet/intel/
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Cc: Julia Lawall <Julia.Lawall@inria.fr>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
While converting to FIELD_PREP() and FIELD_GET(), it was noticed that
some of the RSS defines had *included* the shift in their definitions.
This is completely outside of normal, such that a developer could easily
make a mistake and shift at the usage site (like when using
FIELD_PREP()).
Rename the defines and set them to the "pre-shifted values" so they
match the template the driver normally uses for masks and the member
bits of the mask, which also allows the driver to use FIELD_PREP
correctly with these values. Use GENMASK() for this changed MASK value.
Do the same for the VLAN EMODE defines as well.
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Refactor ice driver to use FIELD_PREP(), which reduces lines of code
and adds clarity of intent.
This code was generated by the following coccinelle/spatch script and
then manually repaired.
Several places I changed to OR into a single variable with |= instead of
using a multi-line statement with trailing OR operators, as it
(subjectively) makes the code clearer.
A local variable vmvf_and_timeout was created and used to avoid multiple
logical ORs being __le16 converted, which shortened some lines and makes
the code cleaner.
Also clean up a couple of places where conversions were made to have the
code read more clearly/consistently.
@prep2@
constant shift,mask;
type T;
expression a;
@@
-(((T)(a) << shift) & mask)
+FIELD_PREP(mask, a)
@prep@
constant shift,mask;
type T;
expression a;
@@
-((T)((a) << shift) & mask)
+FIELD_PREP(mask, a)
Cc: Julia Lawall <Julia.Lawall@inria.fr>
CC: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Commit 6624e780a5 ("ice: split ice_vsi_setup into smaller
functions") has refactored a bunch of code involved in PFR. In this
process, TC queue number adjustment for XDP was lost. Bring it back.
Lack of such adjustment causes interface to go into no-carrier after a
reset, if XDP program is attached, with the following message:
ice 0000:b1:00.0: Failed to set LAN Tx queue context, error: -22
ice 0000:b1:00.0 ens801f0np0: Failed to open VSI 0x0006 on switch 0x0001
ice 0000:b1:00.0: enable VSI failed, err -22, VSI index 0, type ICE_VSI_PF
ice 0000:b1:00.0: PF VSI rebuild failed: -22
ice 0000:b1:00.0: Rebuild failed, unload and reload driver
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Previously, the ice driver had support for using a handler for bonding
netdev events to ensure that conflicting features were not allowed to be
activated at the same time. While this was still in place, additional
support was added to specifically support SRIOV and LAG together. These
both utilized the netdev event handler, but the SRIOV and LAG feature was
behind a capabilities feature check to make sure the current NVM has
support.
The exclusion part of the event handler should be removed since there are
users who have custom made solutions that depend on the non-exclusion of
features.
Wrap the creation/registration and cleanup of the event handler and
associated structs in the probe flow with a feature check so that the
only systems that support the full implementation of LAG features will
initialize support. This will leave other systems unhindered with
functionality as it existed before any LAG code was added.
Fixes: bb52f42ace ("ice: Add driver support for firmware changes for LAG")
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When creating new VSIs, they are assigned into an aggregator node in the
scheduler tree. Information about which aggregator node a VSI is assigned
into is maintained by the vsi->agg_node structure. In ice_vsi_decfg(), this
information is being destroyed, by overwriting the valid flag and the
agg_id field to zero.
For VF VSIs, this breaks the aggregator node configuration replay, which
depends on this information. This results in VFs being inserted into the
default aggregator node. The resulting configuration will have unexpected
Tx bandwidth sharing behavior.
This was broken by commit 6624e780a5 ("ice: split ice_vsi_setup into
smaller functions"), which added the block to reset the agg_node data.
The vsi->agg_node structure is not managed by the scheduler code, but is
instead a wrapper around an aggregator node ID that is tracked at the VSI
layer. Its been around for a long time, and its primary purpose was for
handling VFs. The SR-IOV VF reset flow does not make use of the standard VSI
rebuild/replay logic, and uses vsi->agg_node as part of its handling to
rebuild the aggregator node configuration.
The logic for aggregator nodes stretches back to early ice driver code from
commit b126bd6bcd ("ice: create scheduler aggregator node config and move
VSIs")
The logic in ice_vsi_decfg() which trashes the ice_agg_node data is clearly
wrong. It destroys information that is necessary for handling VF reset,. It
is also not the correct way to actually remove a VSI from an aggregator
node. For that, we need to implement logic in the scheduler code. Further,
non-VF VSIs properly replay their aggregator configuration using existing
scheduler replay logic.
To fix the VF replay logic, remove this broken aggregator node cleanup
logic. This is the simplest way to immediately fix this.
This ensures that VFs will have proper aggregate configuration after a
reset. This is especially important since VFs often perform resets as part
of their reconfiguration flows. Without fixing this, VFs will be placed in
the default aggregator node and Tx bandwidth will not be shared in the
expected and configured manner.
Fixes: 6624e780a5 ("ice: split ice_vsi_setup into smaller functions")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Once logging is enabled the user should read the data from the 'data'
file. The data is in the form of a binary blob that can be sent to Intel
for decoding. To read the data use a command like:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/data > log_data.bin
If the user wants to clear the FW log data that has been stored in the
driver then they can write any value to the 'data' file and that will clear
the data. An example is:
# echo 34 > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/data
In addition to being able to read the data the user can configure how
much memory is used to store FW log data. This allows the user to
increase/decrease the amount of memory based on the users situation.
The data is stored such that if the memory fills up then the oldest data
will get overwritten in a circular manner. To change the amount of
memory the user can write to the 'log_size' file like this:
# echo <value> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/log_size
Where <value> is one of 128K, 256K, 512K, 1M, and 2M. The default value
is 1M.
The user can see the current value of 'log_size' by reading the file:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/log_size
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Once users have configured the FW logging then allow them to enable it
by writing to the 'fwlog/enable' file. The file accepts a boolean value
(0 or 1) where 1 means enable FW logging and 0 means disable FW logging.
# echo <value> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/enable
Where <value> is 0 or 1.
The user can read the 'fwlog/enable' file to see whether logging is
enabled or not. Reading the actual data is a separate patch. To see the
current value then:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/enable
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Users want the ability to debug FW issues by retrieving the
FW logs from the E8xx devices. Use debugfs to allow the user to
configure the log level and number of messages for FW logging.
If FW logging is supported on the E8xx then the file 'fwlog' will be
created under the PCI device ID for the ice driver. If the file does not
exist then either the E8xx doesn't support FW logging or debugfs is not
enabled on the system.
One thing users want to do is control which events are reported. The
user can read and write the 'fwlog/modules/<module name>' to get/set
the log levels. Each module in the FW that supports logging ht as a file
under 'fwlog/modules' that supports reading (to see what the current log
level is) and writing (to change the log level).
The format to set the log levels for a module are:
# echo <log level> > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/<module>
The supported log levels are:
* none
* error
* warning
* normal
* verbose
Each level includes the messages from the previous/lower level
The modules that are supported are:
* general
* ctrl
* link
* link_topo
* dnl
* i2c
* sdp
* mdio
* adminq
* hdma
* lldp
* dcbx
* dcb
* xlr
* nvm
* auth
* vpd
* iosf
* parser
* sw
* scheduler
* txq
* rsvd
* post
* watchdog
* task_dispatch
* mng
* synce
* health
* tsdrv
* pfreg
* mdlver
* all
The module 'all' is a special module which allows the user to read or
write to all of the modules.
The following example command would set the DCB module to the 'normal'
log level:
# echo normal > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
If the user wants to set the DCB, Link, and the AdminQ modules to
'verbose' then the commands are:
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/link
# echo verbose > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/adminq
If the user wants to set all modules to the 'warning' level then the
command is:
# echo warning > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
If the user wants to disable logging for a module then they can set the
level to 'none'. An example setting the 'watchdog' module is:
# echo none > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/watchdog
If the user wants to see what the log level is for a specific module
then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/dcb
This will return the log level for the DCB module. If the user wants to
see the log level for all the modules then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/modules/all
Writing to the module file will update the configuration, but NOT enable the
configuration (that is a separate command).
In addition to configuring the modules, the user can also configure the
number of log messages (nr_messages) to include in a single Admin Receive
Queue (ARQ) event.The range is 1-128 (1 means push every log message, 128
means push only when the max AQ command buffer is full). The suggested
value is 10.
To see/change the resolution the user can read/write the
'fwlog/nr_messages' file. An example changing the value to 50 is
# echo 50 > /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
To see the current value of 'nr_messages' then the command is:
# cat /sys/kernel/debug/ice/0000\:18\:00.0/fwlog/nr_messages
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
The FW logging code doesn't work because there is no way to set
cq_ena or uart_ena so remove the code. This code is the original
(v1) way of FW logging so it should be replaced with the v2 way.
Signed-off-by: Paul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Allow the user to set the symmetric Toeplitz hash function via:
# ethtool -X eth0 hfunc toeplitz symmetric-xor
The driver will reject any new RSS configuration if a field other than
(IP src/dst and L4 src/dst ports) is requested for hashing.
The symmetric RSS will not be supported on PFs not advertising the ADV RSS
Offload flag (ADV_RSS_SUPPORT()), for example the E700 series (i40e).
Reviewed-by: Madhu Chittim <madhu.chittim@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-9-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Allow the user to set the symmetric Toeplitz hash function via:
# ethtool -X eth0 hfunc toeplitz symmetric-xor
All existing RSS configurations will be converted to symmetric unless they
have a non-symmetric field (other than IP src/dst and L4 src/dst ports)
used for hashing. The driver will reject a new RSS configuration if such
a field is requested.
The hash function in the E800 NICs is set per-VSI and a specific AQ
command is needed to modify the hash function. Use the AQ command to
enable setting the symmetric Toeplitz RSS hash function for any VSI
in the new ice_set_rss_hfunc().
When the Symmetric Toeplitz hash function is used, the hardware sets the
input set of the RSS (Toeplitz) algorithm to be the XOR of the fields
index by HSYMM and the fields index by the INSET registers. We use this
to create a symmetric hash by setting the HSYMM registers to point to
their counterparts in the INSET registers:
HSYMM [src_fv] = dst_fv;
HSYMM [dst_fv] = src_fv;
where src_fv and dst_fv are the indexes of the protocol's src and dst
fields.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Jeff Guo <jia.guo@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-8-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The flow director and RSS blocks use separate methods to generate a
unique 64 bit ID for the flow. This is not extendable, especially for
the RSS that already uses all 64 bit space.
Refactor the flow generation API so that the ID is generated within
ice_flow_add_prof(). The FD and RSS blocks caches the generated ID for
later use.
Suggested-by: Dan Nowlin <dan.nowlin@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-7-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Refactor the driver to use a communication data structure for RSS
config. To do so we introduce the new ice_rss_hash_cfg struct, and then
pass it as an argument to several functions.
Also introduce enum ice_rss_cfg_hdr_type to specify a more granular and
flexible RSS configuration:
ICE_RSS_OUTER_HEADERS - take outer layer as RSS input set
ICE_RSS_INNER_HEADERS - take inner layer as RSS input set
ICE_RSS_INNER_HEADERS_W_OUTER_IPV4 - take inner layer as RSS input set for
packet with outer IPV4
ICE_RSS_INNER_HEADERS_W_OUTER_IPV6 - take inner layer as RSS input set for
packet with outer IPV6
ICE_RSS_ANY_HEADERS - try with outer first then inner (same as the
behaviour without this change)
Finally, move the virtchnl_rss_algorithm enum to be with the other RSS
related structures in the virtchnl.h file.
There should be no functional change due to this patch.
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Qi Zhang <qi.z.zhang@intel.com>
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Ahmed Zaki <ahmed.zaki@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-6-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix the values of the ICE_AQ_VSI_Q_OPT_RSS_* registers. Shifting is
already done when the values are used, no need to double shift. Bug was
not discovered earlier since only ICE_AQ_VSI_Q_OPT_RSS_TPLZ (Zero) is
currently used.
Also, rename ICE_AQ_VSI_Q_OPT_RSS_XXX to ICE_AQ_VSI_Q_OPT_RSS_HASH_XXX
for consistency.
Co-developed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-5-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Add the RSS context parameters to struct ethtool_rxfh_param and use the
get/set_rxfh to handle the RSS contexts as well.
This is part 2/2 of the fix suggested in [1]:
- Add a rss_context member to the argument struct and a capability
like cap_link_lanes_supported to indicate whether driver supports
rss contexts, then you can remove *et_rxfh_context functions,
and instead call *et_rxfh() with a non-zero rss_context.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Tony Nguyen <anthony.l.nguyen@intel.com>
CC: Marcin Wojtas <mw@semihalf.com>
CC: Russell King <linux@armlinux.org.uk>
CC: Sunil Goutham <sgoutham@marvell.com>
CC: Geetha sowjanya <gakula@marvell.com>
CC: Subbaraya Sundeep <sbhatta@marvell.com>
CC: hariprasad <hkelam@marvell.com>
CC: Saeed Mahameed <saeedm@nvidia.com>
CC: Leon Romanovsky <leon@kernel.org>
CC: Edward Cree <ecree.xilinx@gmail.com>
CC: Martin Habets <habetsm.xilinx@gmail.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-3-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The get/set_rxfh ethtool ops currently takes the rxfh (RSS) parameters
as direct function arguments. This will force us to change the API (and
all drivers' functions) every time some new parameters are added.
This is part 1/2 of the fix, as suggested in [1]:
- First simplify the code by always providing a pointer to all params
(indir, key and func); the fact that some of them may be NULL seems
like a weird historic thing or a premature optimization.
It will simplify the drivers if all pointers are always present.
- Then make the functions take a dev pointer, and a pointer to a
single struct wrapping all arguments. The set_* should also take
an extack.
Link: https://lore.kernel.org/netdev/20231121152906.2dd5f487@kernel.org/ [1]
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Ahmed Zaki <ahmed.zaki@intel.com>
Link: https://lore.kernel.org/r/20231213003321.605376-2-ahmed.zaki@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
VLAN proto, used in ice XDP hints implementation is stored in ring packet
context. Utilize this value in skb VLAN processing too instead of checking
netdev features.
At the same time, use vlan_tci instead of vlan_tag in touched code,
because VLAN tag often refers to VLAN proto and VLAN TCI combined,
while in the code we clearly store only VLAN TCI.
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-12-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Implement .xmo_rx_vlan_tag callback to allow XDP code to read
packet's VLAN tag.
At the same time, use vlan_tci instead of vlan_tag in touched code,
because VLAN tag often refers to VLAN proto and VLAN TCI combined,
while in the code we clearly store only VLAN TCI.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-11-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In AF_XDP ZC, xdp_buff is not stored on ring,
instead it is provided by xsk_buff_pool.
Space for metadata sources right after such buffers was already reserved
in commit 94ecc5ca4d ("xsk: Add cb area to struct xdp_buff_xsk").
Some things (such as pointer to packet context) do not change on a
per-packet basis, so they can be set at the same time as RX queue info.
On the other hand, RX descriptor is unique for each packet, but is already
known when setting DMA addresses. This minimizes performance impact of
hints on regular packet processing.
Update AF_XDP ZC packet processing to support XDP hints.
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-9-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
RX hash XDP hint requests both hash value and type.
Type is XDP-specific, so we need a separate way to map
these values to the hardware ptypes, so create a lookup table.
Instead of creating a new long list, reuse contents
of ice_decode_rx_desc_ptype[] through preprocessor.
Current hash type enum does not contain ICMP packet type,
but ice devices support it, so also add a new type into core code.
Then use previously refactored code and create a function
that allows XDP code to read RX hash.
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-7-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Use previously refactored code and create a function
that allows XDP code to read HW timestamp.
Also, introduce packet context, where hints-related data will be stored.
ice_xdp_buff contains only a pointer to this structure, to avoid copying it
in ZC mode later in the series.
HW timestamp is the first supported hint in the driver,
so also add xdp_metadata_ops.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-6-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
In order to use XDP hints via kfuncs we need to put
RX descriptor and miscellaneous data next to xdp_buff.
Same as in hints implementations in other drivers, we achieve
this through putting xdp_buff into a child structure.
Currently, xdp_buff is stored in the ring structure,
so replace it with union that includes child structure.
This way enough memory is available while existing XDP code
remains isolated from hints.
Minimum size of the new child structure (ice_xdp_buff) is exactly
64 bytes (single cache line). To place it at the start of a cache line,
move 'next' field from CL1 to CL4, as it isn't used often. This still
leaves 192 bits available in CL3 for packet context extensions.
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-5-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Currently, rx_ptype variable is used only as an argument
to ice_process_skb_fields() and is computed
just before the function call.
Therefore, there is no reason to pass this value as an argument.
Instead, remove this argument and compute the value directly inside
ice_process_skb_fields() function.
Also, separate its calculation into a short function, so the code
can later be reused in .xmo_() callbacks.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-4-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Previously, we only needed RX HW timestamp in skb path,
hence all related code was written with skb in mind.
But with the addition of XDP hints via kfuncs to the ice driver,
the same logic will be needed in .xmo_() callbacks.
Put generic process of reading RX HW timestamp from a descriptor
into a separate function.
Move skb-related code into another source file.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-3-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Previously, we only needed RX hash in skb path,
hence all related code was written with skb in mind.
But with the addition of XDP hints via kfuncs to the ice driver,
the same logic will be needed in .xmo_() callbacks.
Separate generic process of reading RX hash from a descriptor
into a separate function.
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Link: https://lore.kernel.org/r/20231205210847.28460-2-larysa.zaremba@intel.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
To map phy types reported by the hardware to ethtool link mode bits,
ice uses two lookup tables (phy_type_low_lkup, phy_type_high_lkup).
The "low" table has 64 elements to cover every possible bit the hardware
may report, but the "high" table has only 13. If the hardware reports a
higher bit in phy_types_high, the driver would access memory beyond the
lookup table's end.
Instead of iterating through all 64 bits of phy_types_{low,high}, use
the sizes of the respective lookup tables.
Fixes: 9136e1f1e5 ("ice: refactor PHY type to ethtool link mode")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Mode supported is currently reported to the user exactly the same, as
the current mode. That's because mode changing is not implemented.
Remove the leftover mode_supported() op and use mode_get() to fill up
the supported mode exposed to user.
One, if even, mode changing is going to be introduced, this could be
very easily taken back. In the meantime, prevent drivers form
implementing this in wrong way (as for example recent netdevsim
implementation attempt intended to do).
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts some basic cases of ethtool_sprintf() to
ethtool_puts().
The conversions are used in cases where ethtool_sprintf() was being used
with just two arguments:
| ethtool_sprintf(&data, buffer[i].name);
or when it's used with format string: "%s"
| ethtool_sprintf(&data, "%s", buffer[i].name);
which both now become:
| ethtool_puts(&data, buffer[i].name);
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Louis Peens <louis.peens@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix setting dis_rx_filtering depending on whether port vlan is being
turned on or off. This was originally fixed in commit c793f8ea15 ("ice:
Fix disabling Rx VLAN filtering with port VLAN enabled"), but while
refactoring ice_vf_vsi_init_vlan_ops(), the fix has been lost. Restore the
fix along with the original comment from that change.
Also delete duplicate lines in ice_port_vlan_on().
Fixes: 2946204b3f ("ice: implement bridge port vlan")
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Marcin Szycik <marcin.szycik@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
vfs::num_msix_per should be only used as default value for
vf->num_msix. For other use cases vf->num_msix should be used, as VF can
have different MSI-X amount values.
Fix incorrect register index calculation. vfs::num_msix_per and
pf->sriov_base_vector shouldn't be used after implementation of changing
MSI-X amount on VFs. Instead vf->first_vector_idx should be used, as it
is storing value for first irq index.
Fixes: fe1c5ca2fe ("ice: implement num_msix field per VF")
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
When code is applicable for both E822 and E823 devices, rename it from
E822 to E82X.
ICE_PHY_PER_NAC_E822 was unused, so just remove it.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The E822 hardware for Tx timestamping keeps track of how many
outstanding timestamps are still in the PHY memory block. It will not
generate a new interrupt to the MAC until all of the timestamps in the
region have been read.
If somehow all the available data is not read, but the driver has exited
its interrupt routine already, the PHY will not generate a new interrupt
even if new timestamp data is captured. Because no interrupt is
generated, the driver never processes the timestamp data. This state
results in a permanent failure for all future Tx timestamps.
It is not clear how the driver and hardware could enter this state.
However, if it does, there is currently no recovery mechanism.
Add a recovery mechanism via the periodic PTP work thread which invokes
ice_ptp_periodic_work(). Introduce a new check,
ice_ptp_maybe_trigger_tx_interrupt() which checks the PHY timestamp
ready bitmask. If any bits are set, trigger a software interrupt by
writing to PFINT_OICR.
Once triggered, the main timestamp processing thread will read through
the PHY data and clear the outstanding timestamp data. Once cleared, new
data should trigger interrupts as expected.
This should allow recovery from such a state rather than leaving the
device in a state where we cannot process Tx timestamps.
It is possible that this function checks for timestamp data
simultaneously with the interrupt, and it might trigger additional
unnecessary interrupts. This will cause a small amount of additional
processing.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Andrii Staikov <andrii.staikov@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
During reset, TX_TSYN interrupt should be processed as it may process
timestamps in brief moments before and after reset.
Timestamping should be enabled on VSIs at the end of reset procedure.
On ice_get_phy_tx_tstamp_ready error, interrupt should not be rearmed
because error only happens on resets.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Supported number of ntuple filters affect also maximum location value that
can be provided to ethtool command. Update error message to provide info
about max supported value.
Fix double spaces in the error messages.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Pawel Kaminski <pawel.kaminski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
If Clock Generation Unit is present on NIC board user shall know its
details.
Provide the devlink info callback with a new:
- fixed type object (cgu.id) indicating hardware variant of onboard CGU,
- running type object (fw.cgu) consisting of CGU id, config and firmware
versions.
These information shall be known for debugging purposes.
Test (on NIC board with CGU)
$ devlink dev info <bus_name>/<dev_name> | grep cgu
cgu.id 36
fw.cgu 8032.16973825.6021
Test (on NIC board without CGU)
$ devlink dev info <bus_name>/<dev_name> | grep cgu -c
0
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
After the napi context is initialized, map the napi instance
with the queue/queue-set on the corresponding irq line.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Reviewed-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Link: https://lore.kernel.org/r/170147332060.5260.13310934657151560599.stgit@anambiarhost.jf.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There is an error when an interface has the following conditions:
- PF is in an aggregate (bond)
- PF has VFs created on it
- bond is in a state where it is failed-over to the secondary interface
- A VF reset is issued on one or more of those VFs
The issue is generated by the originating PF trying to rebuild or
reconfigure the VF resources. Since the bond is failed over to the
secondary interface the queue contexts are in a modified state.
To fix this issue, have the originating interface reclaim its resources
prior to the tear-down and rebuild or reconfigure. Then after the process
is complete, move the resources back to the currently active interface.
There are multiple paths that can be used depending on what triggered the
event, so create a helper function to move the queues and use paired calls
to the helper (back to origin, process, then move back to active interface)
under the same lag_mutex lock.
Fixes: 1e0f9881ef ("ice: Flesh out implementation of support for SRIOV on bonded interface")
Signed-off-by: Dave Ertman <david.m.ertman@intel.com>
Tested-by: Sujai Buvaneswaran <sujai.buvaneswaran@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20231127212340.1137657-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
