Reset CGX/RPM MAC HW statistics at the time of driver probe()
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any NIX interface type can have maximum 256 channels. So increased the
backpressure ID count to 256 so that it can cover cn9k and cn10k SoCs that
have different NIX interface types with varied maximum channels.
Signed-off-by: Radha Mohan Chintakuntla <radhac@marvell.com>
Link: https://lore.kernel.org/r/20240326184514.1628284-1-radhac@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
A single line of interrupt is used to receive up notifications
and down reply messages from AF to PF (similarly from PF to its VF).
PF acts as bridge and forwards VF messages to AF and sends respsones
back from AF to VF. When an async event like link event is received
by up message when PF is in middle of forwarding VF message then
mailbox errors occur because PF state machine is corrupted.
Since VF is a separate driver or VF driver can be in a VM it is
not possible to serialize from the start of communication at VF.
Hence to differentiate between type of messages at PF this patch makes
sender to set mbox data register with distinct values for up and down
messages. Sender also checks whether previous interrupt is received
before triggering current interrupt by waiting for mailbox data register
to become zero.
Fixes: 5a6d7c9dae ("octeontx2-pf: Mailbox communication with AF")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds TC offload support for matching TCP flags
from TCP header.
Example usage:
tc qdisc add dev eth0 ingress
TC rule to drop the TCP SYN packets:
tc filter add dev eth0 ingress protocol ip flower ip_proto tcp tcp_flags
0x02/0x3f skip_sw action drop
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In current driver 64 BPIDs are reserved for LBK interfaces.
These bpids are 1-to-1 mapped to LBK interface channel numbers.
In some usecases one LBK interface required more than one
bpids and in some case they may not require at all.
These usescase can't be address with the current implementation
as it always reserves only one bpid per LBK channel.
This patch addresses this issue by creating free bpid pool from these
64 bpids instead of 1-to-1 mapping to the lbk channel.
Now based on usecase LBK interface can request a bpid using (bp_enable()).
This patch also reduces the number of bpids for cgx interfaces to 8
and adds proper error code
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds hardware profile supports for extracting packet headers.
It makes sure that hardware is capabale of extracting ICMP, CPT, ERSPAN
headers.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On latest silicon versions SA cam entries increased to 256.
This patch fixes the datatype of sa_entries in mcs_hw_info
struct to u16 to hold 256 entries.
Fixes: 080bbd19c9 ("octeontx2-af: cn10k: mcs: Add mailboxes for port related operations")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A new mailbox is added to support offloading of multicast/mirror
functionality. The mailbox also supports dynamic updation of the
multicast/mirror list.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds tc offload support for matching on ICMP type and code.
Example usage:
To enable adding tc ingress rules
tc qdisc add dev eth0 ingress
TC rule drop the ICMP echo reply:
tc filter add dev eth0 protocol ip parent ffff: \
flower ip_proto icmp type 8 code 0 skip_sw action drop
TC rule to drop ICMPv6 echo reply:
tc filter add dev eth0 protocol ipv6 parent ffff: flower \
indev eth0 ip_proto icmpv6 type 128 code 0 action drop
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends flower offload support for MPLS protocol.
Due to hardware limitation, currently driver supports lse
depth up to 4.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
PTP block supports generating PPS output signal on GPIO pin. This patch
adds the support in the PTP PHC driver using standard periodic output
interface.
User can enable/disable/configure PPS by writing to the below sysfs entry
echo perout.index start.sec start.nsec period.sec period.nsec >
/sys/class/ptp/ptp0/period
Example to generate 50% duty cycle PPS signal:
echo 0 0 0 0 500000000 > /sys/class/ptp/ptp0/period
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the newer silicon versions in CN10K series supports a feature
where in the current PTP timestamp in HW can be updated atomically
without losing any cpu cycles unlike read/modify/write register.
This patch uses this feature so that PTP accuracy can be improved
while adjusting the master offset in HW. There is no need for SW
timecounter when using this feature. So removed references to SW
timecounter wherever appropriate.
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the current TC flower offload support to enable filters matching
inner VLAN, and support offload of those filters to hardware.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230804045935.3010554-3-sumang@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Driver support to offload TC flower rules which matches
against SPI field of IPSEC packets (AH/ESP).
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of today, hardware does not support installing tc filter
rules based on priority. This patch adds support to install
the hardware rules based on priority. The final hardware rules
will not be dependent on rule installation order, it will be strictly
priority based, same as software.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230721043925.2627806-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Add option to toggle DROP_RE bit in rx cfg mbox. This helps in
modifying the config runtime as opposed to setting available via
nix_lf_alloc() mbox at NIX LF init time.
Signed-off-by: Nithin Dabilpuram <ndabilpuram@marvell.com>
Signed-off-by: Jerin Jacob Kollanukkaran <jerinj@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DWRR MTU config added for SDP and RPM/LBK links on CN10K
silicon is further extended on CK10KB silicon variant and made
it configurable. Now there are 4 DWRR MTU config to choose while
setting transmit scheduler's RR_WEIGHT.
Here we are reserving one config for each of RPM, SDP and LBK.
NIXX_AF_DWRR_MTUX(0) ---> RPM
NIXX_AF_DWRR_MTUX(1) ---> SDP
NIXX_AF_DWRR_MTUX(2) ---> LBK
PF/VF drivers can choose the DWRR_MTU to be used by setting
SMQX_CFG[pkt_link_type] to one of above. TLx_SCHEDULE[RR_WEIGHT]
is to be as configured 'quantum / 2^DWRR_MTUX[MTU]'. DWRR_MTU
of each link is exposed to PF/VF drivers via mailbox for
RR_WEIGHT calculation.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support to select L3 SRC or DST only, L4 SRC or DST only for RSS
calculation.
AF consumer may have requirement as we can select only SRC or DST data for
RSS calculation in L3, L4 layers. With this requirement there will be
following combinations, IPV[4,6]_SRC_ONLY, IPV[4,6]_DST_ONLY,
[TCP,UDP,SCTP]_SRC_ONLY, [TCP,UDP,SCTP]_DST_ONLY. So, instead of creating
a bit for each combination, we are using upper 4 bits (31:28) in the
flow_key_cfg to represent the SRC, DST selection. 31 => L3_SRC,
30 => L3_DST, 29 => L4_SRC, 28 => L4_DST. These won't be part of flow_cfg,
so that we don't need to change the existing ABI.
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware enables PFs and allocate mbox resources for each of the PFs.
Currently PF driver configures mbox resources without checking whether
PF is enabled or not. This results in crash. This patch fixes this issue
by skipping disabled PF's mbox initialization.
Fixes: 9bdc47a6e3 ("octeontx2-af: Mbox communication support btw AF and it's VFs")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. As per previous implementation, mask and control parameter to
generate the field hash value was not passed to the caller program.
Updated the secret key mbox to share that information as well,
as a part of the fix.
2. Earlier implementation did not consider hash reduction of both
source and destination IPv6 addresses. Only source IPv6 address
was considered. This fix solves that and provides option to hash
Fixes: 56d9f5fd22 ("octeontx2-af: Use hashed field in MCAM key")
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Sai Krishna <saikrishnag@marvell.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update type of prof and prof_mask fields in nix_as_enq_req
from u64 to struct nix_bandprof_s, which is 128 bits wide.
This is to address warnings with compiling with gcc-12 W=1
regarding string fortification.
Although the union of which these fields are a member is 128bits
wide, and thus writing a 128bit entity is safe, the compiler flags
a problem as the field being written is only 64 bits wide.
CC [M] drivers/net/ethernet/marvell/octeontx2/nic/otx2_common.o
scripts/Makefile.build:252: ./drivers/net/ethernet/marvell/octeontx2/nic/Makefile: otx2_dcbnl.o is added to multiple modules: rvu_nicpf rvu_nicvf
CC [M] drivers/net/ethernet/marvell/octeontx2/nic/otx2_dcbnl.o
CC [M] drivers/net/ethernet/marvell/octeontx2/nic/qos_sq.o
CC [M] drivers/net/ethernet/marvell/octeontx2/af/rvu_debugfs.o
CC [M] drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.o
In file included from ./include/linux/string.h:254,
from ./include/linux/bitmap.h:11,
from ./include/linux/cpumask.h:12,
from ./arch/x86/include/asm/paravirt.h:17,
from ./arch/x86/include/asm/cpuid.h:62,
from ./arch/x86/include/asm/processor.h:19,
from ./arch/x86/include/asm/timex.h:5,
from ./include/linux/timex.h:67,
from ./include/linux/time32.h:13,
from ./include/linux/time.h:60,
from ./include/linux/stat.h:19,
from ./include/linux/module.h:13,
from drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c:8:
In function 'fortify_memcpy_chk',
inlined from 'rvu_nix_blk_aq_enq_inst' at drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c:969:4:
./include/linux/fortify-string.h:529:25: error: call to '__read_overflow2_field' declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
529 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In function 'fortify_memcpy_chk',
inlined from 'rvu_nix_blk_aq_enq_inst' at drivers/net/ethernet/marvell/octeontx2/af/rvu_nix.c:984:4:
./include/linux/fortify-string.h:529:25: error: call to '__read_overflow2_field' declared with attribute warning: detected read beyond size of field (2nd parameter); maybe use struct_group()? [-Werror=attribute-warning]
529 | __read_overflow2_field(q_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
cc1: all warnings being treated as errors
Compile tested only!
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Link: https://lore.kernel.org/r/20230329112356.458072-1-horms@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CPT HW would trigger the CPT AF FLT interrupt when CPT engines
hits some uncorrectable errors and AF is the one which receives
the interrupt and recovers the engines.
This patch adds a mailbox for CPT VFs to request for CPT faulted
and recovered engines info.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The CN10K CPT coprocessor contains a context processor
to accelerate updates to the IPsec security association
contexts. The context processor contains a context cache.
This patch updates CPT LF ALLOC mailbox to config ctx_ilen
requested by VFs. CPT_LF_ALLOC:ctx_ilen is the size of
initial context fetch.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
On OcteonTX2 SoC, the admin function (AF) is the only one with all
priviliges to configure HW and alloc resources, PFs and it's VFs
have to request AF via mailbox for all their needs.
This patch adds a new mailbox for CPT VFs to request for CPT LF
reset.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Updates CPT inbound inline IPsec configure mailbox to take
CPT credit, opcode, credit_th and bpid from VF.
This patch also adds a mailbox to read inbound IPsec
configuration.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. Added support to filter packets based on IP fragment.
For IPv4 packets check for ip_flag == 0x20 (more fragment bit set).
For IPv6 packets check for next_header == 0x2c (next_header set to
'fragment header for IPv6')
2. Added configuration support from both "ethtool ntuple" and "tc flower".
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. If a profile does not support DMAC extraction then avoid installing NPC
flow rules for unicast. Similarly, if LXMB(L2 and L3) extraction is not
supported by the profile then avoid installing broadcast and multicast
rules.
2. Allow MCAM entry insertion for promiscuous mode.
3. For the profiles where DMAC is not extracted in MKEX key default
unicast entry installed by AF is not valid. Hence do not use action
from the AF installed default unicast entry for such cases.
4. Adjacent packet header fields in a packet like IP header source
and destination addresses or UDP/TCP header source port and destination
can be extracted together in MKEX profile. Therefore MKEX profile can be
configured to in two ways:
a. Total of 4 bytes from start of UDP header(src port
+ destination port)
or
b. Two bytes from start and two bytes from offset 2
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20221118053329.2288486-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Hardware triggers an interrupt for events like PN wrap to zero,
PN crosses set threshold. This interrupt is received
by the MCS_AF. MCS AF then finds the PF/VF to which SA is mapped
and notifies them using mcs_intr_notify mbox message.
PF/VF using mcs_intr_cfg mbox can configure the list
of interrupts for which they want to receive the
notification from AF.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mailbox messages to return the resource stats to the
caller. Stats of SecY, SC and SAs as per the macsec standard,
TCAM flow id hits/miss, mailbox to clear the stats are
implemented.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Ankur Dwivedi <adwivedi@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To establish a macsec connection association netdev driver
needs hardware resources like SecY, TCAM flows, SCs and SAs.
This patch manages allocating, freeing and configuring those
resources. AF consumers can request resources and configure them
via these mailbox messages. AF can allocate until it runs out of
hardware resources.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are set of configurations to be done at MCS port level like
bringing port out of reset, making port as operational or bypass.
This patch adds all the port related mailbox message handlers
so that AF consumers can use them.
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Vamsi Attunuru <vattunuru@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Errata:
The ptp_clock_hi rollsover to zero one clock cycle before it
reaches one second boundary. As a result, the pps threshold
comparison fails after one second and the pps output signal
won't toggle further.
This patch workarounds the issue by programming the pps_lo_incr
register to 500msec minus one clock cycle period, ensuring that
the pps threshold comparison succeeds at one second rollover
boundary and pps edge toggles. After that point, the driver will
have enough time (~500msec) to reset the pps threshold value.
After each one second boundary, hrtimer is invoked which resets
the pps threshold value.
Signed-off-by: Naveen Mamindlapalli <naveenm@marvell.com>
Signed-off-by: Rakesh Babu Saladi <rsaladi2@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the maximum time firmware should poll for a link.
If not set firmware could block CPU for a long time resulting
in mailbox failures. If link doesn't come up within 1second,
firmware will anyway notify the status as and when LINK comes up
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha Sowjanya <gakula@marvell.com>
Link: https://lore.kernel.org/r/20220712161815.12621-1-gakula@marvell.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In few error cases MAC(CGX/RPM) block is having 0 lmacs.
AF driver uses MAC block with lmac pair to get firmware
data etc. These commands will fail as there is no LMAC
associated with MAC block.
This patch skips the probe of these MAC blocks such that AF driver
uses correct MAC block and LMAC pair for firmware communication and
define new LMAC_AF_ERROR types for command timeout etc.
This patch also enables channel back pressure for all LMACs.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Exact match table modification requires wider fields as it has
more number of slots to fill in. Modifying an entry in exact match
table may cause hash collision and may be required to delete entry
from 4-way 2K table and add to fully associative 32 entry CAM table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
CN10KB variant of CN10K series of silicons supports
a new feature where in a large protocol field
(eg 128bit IPv6 DIP) can be condensed into a small
hashed 32bit data. This saves a lot of space in MCAM key
and allows user to add more protocol fields into the filter.
A max of two such protocol data can be hashed.
This patch adds support for hashing IPv6 SIP and/or DIP.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
This reverts commit 2ef8e39f58, reversing
changes made to e7ce9fc9ad.
There are build warnings here which break the normal
build due to -Werror. Ratheesh was nice enough to quickly
follow up with fixes but didn't hit all the warnings I
see on GCC 12 so to unlock net-next from taking patches
let get this series out for now.
Link: https://lore.kernel.org/r/20220707013201.1372433-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Exact match table modification requires wider fields as it has
more number of slots to fill in. Modifying an entry in exact match
table may cause hash collision and may be required to delete entry
from 4-way 2K table and add to fully associative 32 entry CAM table.
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10KB variant of CN10K series of silicons supports
a new feature where in a large protocol field
(eg 128bit IPv6 DIP) can be condensed into a small
hashed 32bit data. This saves a lot of space in MCAM key
and allows user to add more protocol fields into the filter.
A max of two such protocol data can be hashed.
This patch adds support for hashing IPv6 SIP and/or DIP.
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Signed-off-by: Ratheesh Kannoth <rkannoth@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CN10K MAC block (RPM) and Octeontx2 MAC block (CGX) both supports
PFC flow control and 802.3X flow control pause frames.
Each MAC block supports max 4 LMACS and AF driver assigns same
(MAC,LMAC) to PF and its VFs. As PF and its share same (MAC,LMAC)
pair we need resource management to address below scenarios
1. Maintain PFC and 8023X pause frames mutually exclusive.
2. Reject disable flow control request if other PF or Vfs
enabled it.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Prirority based flow control (802.1Qbb) mechanism is similar to
ethernet pause frames (802.3x) instead pausing all traffic on a link,
PFC allows user to selectively pause traffic according to its class.
Oceteontx2 MAC block (CGX) and CN10K Mac block (RPM) both supports
PFC. As upper layer mbox handler is same for both the MACs, this
patch configures PFC by calling apporopritate callbacks.
Signed-off-by: Sunil Kumar Kori <skori@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Kovvuri Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's been observed that sometimes link credit restore takes
a lot of time than the current timeout. This patch increases
the default timeout value and return the proper error value
on failure.
Fixes: 1c74b89171 ("octeontx2-af: Wait for TX link idle for credits change")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds support to flush or invalidate CPT CTX entries as part of FLR
and also provides a mailbox to flush CPT CTX entries in case of
graceful exit.
This patch also adds support for AF -> CPT PF uplink mailbox messages
and adds a new mbox message to submit a CPT instruction from AF.
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
PTP hardware block can be configured to utilize
the external clock. Also the current ptp timestamp
can be captured when external trigger is applied on
a gpio pin. These features are required in scenarios
like connecting a external timing device to the chip
for time synchronization. The timing device provides
the clock and trigger(PPS signal) to the PTP block.
This patch does the following:
1. configures PTP block to use external clock
frequency and timestamp capture on external event.
2. sends PTP_REQ_EXTTS events to kernel ptp phc susbsytem
with captured timestamps
3. aligns PPS edge to adjusted ptp clock in the ptp device
by setting the PPS_THRESH to the reminder of the last
timestamp value captured by external PPS
Signed-off-by: Yi Guo <yig@marvell.com>
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC on CN10K support hardware timestamping such that 8 bytes addition
header is prepended to incoming packets. This patch does necessary
configuration to enable Hardware time stamping upon receiving request
from PF netdev interfaces.
Timestamp configuration is different on MAC (CGX) Octeontx2 silicon
and MAC (RPM) OcteonTX3 CN10k. Based on silicon variant appropriate
fn() pointer is called. Refactor MAC specific mbox messages to remove
unnecessary gaps in mboxids.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimized KPU1 entry processing for variable-length custom L2 headers
of size 24B, 90B by
- Moving LA LTYPE parsing for 24B and 90B headers to PKIND.
- Removing LA flags assignment for 24B and 90B headers.
- Reserving a PKIND 55 to parse variable length headers.
Also, new mailbox(NPC_SET_PKIND) added to configure PKIND with
corresponding variable-length offset, mask, and shift count
(NPC_AF_KPUX_ENTRYX_ACTION0).
Signed-off-by: Kiran Kumar K <kirankumark@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per HW errata AQ modification to CQ could be discarded on heavy
traffic. This patch implements workaround for the same after each
CQ write by AQ check whether the requested fields (except those
which HW can update eg: avg_level) are properly updated or not.
If CQ context is not updated then perform AQ write again.
Signed-off-by: Hariprasad Kelam <hkelam@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On OcteonTX2/CN10K SoC, the admin function (AF) is the only one
with all priviliges to configure HW and alloc resources, PFs and
it's VFs have to request AF via mailbox for all their needs.
This patch adds new mailbox messages for CPT PFs and VFs to configure
HW resources for inline-IPsec.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Srujana Challa <schalla@marvell.com>
Signed-off-by: Vidya Sagar Velumuri <vvelumuri@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixed inconsistent license text across the RVU admin
function driver.
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
