Currently QCA808x driver does not fill the possible_interfaces.
2.5G QCA808x support SGMII and 2500Base-X while 1G model only supports
SGMII, so fill the possible_interfaces accordingly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are 2 versions of QCA808x, one 2.5G capable and one 1G capable.
Currently, this matter only in the .get_features call however, it will
be required for filling supported interface modes so lets add a helper
that can be reused.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Generalize some qca808x LED functions in preparation for qca807x LED
support.
The LED implementation of qca808x and qca807x is the same but qca807x
supports also Fiber port and have different hw control bits for Fiber
port. To limit code duplication introduce micro functions that takes reg
instead of LED index to tweak all the supported LED modes.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LED implementation of qca808x and qca807x is the same but qca807x
supports also Fiber port and have different hw control bits for Fiber
port.
In preparation for qca807x introduction, move all the common define to
shared header.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move more function to shared library in preparation for introduction of
new PHY Family qca807x that will make use of both functions from at803x
and qca808x as it's a transition PHY with some implementation of at803x
and some from the new qca808x.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
qca808x PHY provide support for the led_polarity_set OP to configure
and apply the active-low property but on PHY reset, the Active High bit
is not set resulting in the LED driven as active-low.
To fix this, check if active-low is not set in DT and enable Active High
polarity by default to restore correct funcionality of the LED.
Fixes: 7196062b64 ("net: phy: at803x: add LED support for qca808x")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In switching to using phy_modify_mmd and a more short version of the
LED ON/OFF condition in later revision, it was made a logic error where
value ? QCA808X_LED_FORCE_ON : QCA808X_LED_FORCE_OFF is always true as
value is always OR with QCA808X_LED_FORCE_EN due to missing ()
resulting in the testing condition being QCA808X_LED_FORCE_EN | value.
Add the () to apply the correct condition and restore correct
functionality of the brightness ON/OFF.
Fixes: 7196062b64 ("net: phy: at803x: add LED support for qca808x")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Almost all the QCA8081 PHY driver OPs are specific and only some of them
use the generic at803x.
To make the at803x code slimmer, move all the specific qca808x regs and
functions to a dedicated PHY driver.
Probe function and priv struct is reworked to allocate and use only the
qca808x specific data. Unused data from at803x PHY driver are dropped
from at803x priv struct.
Also a new Kconfig is introduced QCA808X_PHY, to compile the newly
introduced PHY driver for QCA8081 PHY.
As the Kconfig name starts with Qualcomm the same order is kept.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20240129141600.2592-6-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
