After a chip reset, the beacon timers have to re-programmed
correctly for a station in associated state. Use the PS flags
to ensure that this is done after a TSF sync happens, otherwise
the driver ends up using incorrect values for TBTT/DTIM in
powersave mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ps_flags' is used/accessed in a variety of contexts
and requires proper locking. Use 'sc_pm_lock' appropriately.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a fatal interrupt is received or it is detected that the baseband
has hung, the chip has to be reset immediately. Otherwise, we end up
processing spurious interrupts. Ensure that we bail out properly in
the ISR when the reset work hasn't completed yet.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'sc_flags' variable is being used in a number of places
with no locking whatsoever. This patch converts the usage
of sc_flags to atomic ops.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And use a helper function to setup antennae after a reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Currently, there is no synchronization between the reset
work and the tx-poll work. Fix this and make sure that we
bail out properly if a reset work is in progress.
* Cleanup the PLL WAR and enable it for AR9340 too and
use a helper for restarting work/timers after a reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add link.c and move all the link/connection monitoring
code to it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is waking up from sleep state, the cycle counters
might have incorrect readings. So it is better not to update those
readings with software counters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211's IEEE80211_CONF_OFFCHANNEL can be used directly
to track offchannel state. Also pass the correct boolean
value to ath9k_hw_startpcureceive().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MCI interrupts have to be enabled only when BTCOEX is
actually in use.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This returns many of the values that formerly could
only be obtained from debugfs. This should be an
improvement when trying to access these counters
programatically. Currently this support is only
enabled when DEBUGFS is enabled because otherwise
these stats are not accumulated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been found that active Rx can interfere with stopping tx DMA, which
could result in at least parts of those "Failed to stop Tx DMA!" messages.
Stopping rx before tx should prevent that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* PS_WAIT_FOR_TX_ACK is used in network-sleep mode and checking
it for handling IDLE transitions is incorrect. Fix this.
* RX PCU/DMA engines have to be stopped before setting the chip into
full-sleep mode - otherwise the chip becomes mute.
* Make things a bit clear by checking explicitly for network-sleep
mode in the tx() routine and add a couple of debug statements
to aid PS debugging.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
As of now beacon configuration is being called multiple times
in bss info change notification. This patch avoids multiple
configuration and make it simpler.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it's only called when beacons are stuck, move it to the SWBA handler
tasklet, to avoid doing redundant checks on every single interrupt.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware needs a reset to recover from full sleep. Issue this reset
directly in the ath9k_config call that turns off idle, otherwise tx
remains dead until the first channel change after the idle state change
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This counts any failure during getting packets into
the DMA buffers, including out-of-memory, etc.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit c1afdaff90.
Users have reported connection failures in 3.3.1 and suspend/resume
failures in 3.4-rcX. Revert this commit for now - PS IDLE can be
fixed in a clean manner later on.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the experiment with Azimuth ADEPT-n testbed where the APs transmit
power was reduced to 25% and the signal strength was futher attenuated
by 20dB and induced a path loss of ~7dB, the station was reporting
beacon losses and the following issue were observed.
* rx clear is stuck at low for more than 300ms
* dcu chain and complete state is stuck at one of the hang signature
This patch triggers the hang detection logic that recovers the chip
from any of the above conditions. As the issue was originally reported
in ChromeOs with AR9382 chips, this detection logic is enabled only for
AR9380/2 chips.
Cc: Paul Stewart <pstew@google.com>
Reported-by: Gary Morain <gmorain@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Remove aggregation flags" changed how
nodes were being initialized. Use the HW HT cap bits
to initialize/de-initialize nodes, else we would be
accessing an uninitialized entry during a suspend/resume cycle,
resulting in a panic.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 provides short preamble information and ERP protection
information on a per-BSS basis, which can be used. Remove flags
stored in the driver, which was incorrect since they were being used
in a global manner.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SC_OP_TXAGGR and SC_OP_RXAGGR are not really needed.
The HT capabilities of the station and HW can be used instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The logic to determine whether to use FCC is a bit convoluted.
Use a small helper function to decide whether FCC is to be
used.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not needed and will not be used anyway since
unsupported interfaces are not allowed to be created.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to mask out SWBA/BMISS from the
interrupt mask in start().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check for PS_WAIT_FOR_TX_ACK was inverted, the hardware should only go
to full sleep if no tx is pending.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The proper place to configure bss info is at assoc notification. So that
ath9k continues to work if the supirous bssid notification will be
removed in future.
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9003 uses a global tx status queue, processing tx status outside of
the regular tx tasklet is dangerous and messes up hardware/software
synchronization of tx status events.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_set_channel is called from ath9k_config which already has proper
PS wrappers
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the corresponding code/logic was removed in
"ath9k: rework power state handling"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
channelFlags doesn't contain the operating HT mode.
Use IS_CHAN_HT40 to determine if the current channel is
in HT40 mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix invalid noisefloor reading due to channel update"
preserves the current channel noisefloor readings before updating
channel type at the same channel index. It is also updating the curchan
pointer. As survey updation is also referring curchan pointer to fetch
the appropriate index, which might leads to invalid memory access. This
patch partially reverts the change and stores the noise floor history
buffer before updating channel type w/o updating curchan.
Cc: stable@kernel.org
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many systems (e.g. embedded systems) do not have wifi modules connected to
bluetooth modules, so bluetooth coexistence is irrelevant there. With the
addition of MCI support, ath9k picked up quite a bit of extra code that
can be compiled out this way.
This patch redefines ATH9K_HW_CAP_MCI and adds an inline wrapper for
querying the bluetooth coexistence scheme, allowing the compiler to
eliminate code that uses it, with only very little use of #ifdef.
On MIPS this reduces the total size for the modules by about 20k.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.
Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When processing A-MPDU tx status, only send a BAR for the failed packet
with the highest sequence number.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently in ath9k code there is an attempt which is meant to
disable ANI for ar9100 and ar9340. But it doesn't really achieve
this. All it does is disable ANI init and setup (i.e. calls to
ath9k_hw_ani_setup and ath9k_hw_ani_init). Since ath9k_hw_ani_setup is
not called ah->config.ani_poll_interval is never initialized (i.e. it
is always zero) and ath_ani_calibrate always executes ANI procedures
(over uninitialized ANI parameters).
Moreover, ath_ani_calibrate is being called each 1ms because
common->ani.timer is set to zero interval because
ah->config.ani_poll_interval==0 (and thus smallest value of all
intervals). Normally it should not be called this often.
This patch changes the code so config.enable_ani is used to check if
ANI should be performed.
config.enable_ani is initialized to true by default. This patch sets
it to false for ar9100 and ar9340.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To help debugging write a log entry when long calibration, short
calibration or ANI is performed.
Signed-off-by: Nikolay Martynov <mar.kolya@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Recently more places in mac80211 call drv_flush to ensure proper order
for state changes wrt. powersave, channel changes, etc. On some systems
such calls lead to spurious logspam about failing to stop tx dma, as well
as hardware resets that go along with that.
Instead of dropping packets in a place where it's completely unnecessary,
only do it when drop == true.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turning off the radio when mac80211 tells the driver that it's idle is not
a good idea, as idle interfaces might still occasionally scan or send packets.
The only time the radio can be safely turned off is when drv_stop has been
called. In the mean time, use sc->ps_idle only to indicate network sleep vs
full sleep.
Move the LED GPIO changes out of the PCI suspend/resume path, the start/stop
functions already take care of that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
