When entering RF-kill, mac80211 tears down BA sessions, but
due to RF-kill the commands aren't sent to the device. As a
result, there can be frames pending on the reorder buffer or
perhaps even received while doing so, leading to warnings.
Avoid the warnings by doing the BA session teardown normally
even in RF-kill, which also requires queue sync.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.0762cd80fb3d.I43c5877f3b546159b2db4f36d6d956b333c41cf0@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
If pre-recovery mac80211 tried to disable a link but this disablement
failed, then there might be a mismatch between mac80211 assuming the
link has been disabled and the driver still having the data around.
During recover itself, that is not a problem, but should the link be
activated again at a later point, iwlwifi will refuse the activation as
it detects the inconsistent state.
Solve this corner-case by iterating the station in the restart cleanup
handler.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240513132416.d2fd60338055.I840d4fdce5fd49fe69896d928b071067e3730259@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Adjust EMLSR activation to account for traffic levels. By
tracking the number of RX/TX MPDUs, EMLSR will be activated only when
traffic volume meets the required threshold.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240505091420.9480f99ac8fc.If9eb946e929a39e10fe5f4638bc8bc3f8976edf1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The first "new features" pull request for v6.10 with changes both in
stack and in drivers. The big thing in this pull request is that
wireless subsystem is now almost free of sparse warnings. There's only
one warning left in ath11k which was introduced in v6.9-rc1 and will
be fixed via the wireless tree.
Realtek drivers continue to improve, now we have support for RTL8922AE
and RTL8723CS devices. ath11k also has long waited support for P2P.
This time we have a small conflict in iwlwifi as we didn't consider it
as major enough to justify merging wireless tree to wireless-next. But
Stephen has an example merge resolution which should help with fixing
the conflict:
https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/
Major changes:
rtw89
* RTL8922AE Wi-Fi 7 PCI device support
rtw88
* RTL8723CS SDIO device support
iwlwifi
* don't support puncturing in 5 GHz
* support monitor mode on passive channels
* BZ-W device support
* P2P with HE/EHT support
ath11k
* P2P support for QCA6390, WCN6855 and QCA2066
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmYNIqIRHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZt8jAf9H+o91boD34/qVdI5LWEcFhVKEkHpNtwm
Y1sTKNBEtN1Gs2zcljjO6PqN9N4v2+lA42KSpzP5M42FfpI2aATI2v8jYsKTXOl2
YVwF+8pDiAsi0YtQTxIthygjzTpsePCfj8z0xJaKGm195T+fMm9UebYETrfxxOp/
z5StsJIPI0twgSLKKUWvLpX4ESt0l0HLJY1ok99sk4Cj36EKn6b9LbBinDKr6GcQ
mGNtPyq0j4l0kS5qae9BbXZUohO54o8wiFnApdwGfA7S/kLY7eUtwZy7T050b62P
zbNafwZbIjrH7dNcGfe6Fdr7PjQYFeI5Nh7dXxqM2LJOQsYXU/tcWQ==
=WrPE
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.10
The first "new features" pull request for v6.10 with changes both in
stack and in drivers. The big thing in this pull request is that
wireless subsystem is now almost free of sparse warnings. There's only
one warning left in ath11k which was introduced in v6.9-rc1 and will
be fixed via the wireless tree.
Realtek drivers continue to improve, now we have support for RTL8922AE
and RTL8723CS devices. ath11k also has long waited support for P2P.
This time we have a small conflict in iwlwifi, Stephen has an example
merge resolution which should help with fixing the conflict:
https://lore.kernel.org/all/20240326100945.765b8caf@canb.auug.org.au/
Major changes:
rtw89
* RTL8922AE Wi-Fi 7 PCI device support
rtw88
* RTL8723CS SDIO device support
iwlwifi
* don't support puncturing in 5 GHz
* support monitor mode on passive channels
* BZ-W device support
* P2P with HE/EHT support
ath11k
* P2P support for QCA6390, WCN6855 and QCA2066
* tag 'wireless-next-2024-04-03' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (122 commits)
wifi: mt76: mt7915: workaround dubious x | !y warning
wifi: mwl8k: Avoid -Wflex-array-member-not-at-end warnings
wifi: ti: Avoid a hundred -Wflex-array-member-not-at-end warnings
wifi: iwlwifi: mvm: fix check in iwl_mvm_sta_fw_id_mask
net: rfkill: gpio: Convert to platform remove callback returning void
wifi: mac80211: use kvcalloc() for codel vars
wifi: iwlwifi: reconfigure TLC during HW restart
wifi: iwlwifi: mvm: don't change BA sessions during restart
wifi: iwlwifi: mvm: select STA mask only for active links
wifi: iwlwifi: mvm: set wider BW OFDMA ignore correctly
wifi: iwlwifi: Add support for LARI_CONFIG_CHANGE_CMD cmd v9
wifi: iwlwifi: mvm: Declare HE/EHT capabilities support for P2P interfaces
wifi: iwlwifi: mvm: Remove outdated comment
wifi: iwlwifi: add support for BZ_W
wifi: iwlwifi: Print a specific device name.
wifi: iwlwifi: remove wrong CRF_IDs
wifi: iwlwifi: remove devices that never came out
wifi: iwlwifi: mvm: mark EMLSR disabled in cleanup iterator
wifi: iwlwifi: mvm: fix active link counting during recovery
wifi: iwlwifi: mvm: assign link STA ID lookups during restart
...
====================
Link: https://lore.kernel.org/r/20240403093625.CF515C433C7@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the previous commit, I renamed the variable to differentiate
mac80211/mvm link STA, but forgot to adjust the check. The one
from mac80211 is already non-NULL anyway, but the mvm one can
be NULL when the mac80211 isn't during link switch conditions.
Fix the check.
Fixes: 2783ab506e ("wifi: iwlwifi: mvm: select STA mask only for active links")
Reviewed-by: Daniel Gabay <daniel.gabay@intel.com>
Reviewed-by: Miriam Rachel Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240325180850.e95b442bafe9.I8c0119fce7b00cb4f65782930d2c167ed5dd0a6e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During restart, we haven't added BA sessions, so we also cannot
change them to switch between links when that happens in restart.
Short-circuit the appropriate function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.70ba08540db0.Ic604d384e660c755308a49a79d3f7e78bc27597c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During reconfig, we might send keys, but those should be only
sent to already active link stations. Iterate only active ones
to fix that issue.
Fixes: aea99650f7 ("wifi: iwlwifi: mvm: set STA mask for keys in MLO")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.c6818d1c6033.I6357f05c55ef111002ddc169287eb356ca0c1b21@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This comment was added when iwl_mvm_alloc_sta_after_restart configured
the FW with an internal station, but then it was changed by
164a52d45e ("wifi: iwlwifi: mvm: send full STA during HW restart")
to configure the full sta, So there is no reason to "wait for mac80211 to
add the STA" as this is exacly where it happens.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Link: https://msgid.link/20240320232419.d656c2385b06.Icccd0640eb9f1ad72ff74792086435dfc0bee6eb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When restarting the HW, mac80211 first adds the STA back with only one
link enabled. This means that iwl_mvm_alloc_sta_after_restart will not
see the other links and will not do the assignment.
As such, do the assignment when mac80211 is activating the link for the
station.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Reviewed-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.4a3273e5c6be.I7cb6cf096ab135f4b489f2806b116563624aa5ee@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For the mvm driver, data structures match what's in the firmware,
we allocate FW IDs for them already etc. During link switch we
already allocate/free the STA links appropriately, but initially
we'd allocate them always. Fix this to allocate memory, a STA ID,
etc. only for active links.
Fixes: 57974a55d9 ("wifi: iwlwifi: mvm: refactor iwl_mvm_mac_sta_state_common()")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240319100755.f2093ff73465.Ie891e1cc9c9df09ae22be6aad5c143e376f40f0e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Guard against invalid station IDs in iwl_mvm_mld_rm_sta_id as that would
result in out-of-bounds array accesses. This prevents issues should the
driver get into a bad state during error handling.
Signed-off-by: Benjamin Berg <benjamin.berg@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20240320232419.d523167bda9c.I1cffd86363805bf86a95d8bdfd4b438bb54baddc@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The second features pull request for v6.8. A bigger one this time with
changes both to stack and drivers. We have a new Wifi band RFI (WBRF)
mitigation feature for which we pulled an immutable branch shared with
other subsystems. And, as always, other new features and bug fixes all
over.
Major changes:
cfg80211/mac80211
* AMD ACPI based Wifi band RFI (WBRF) mitigation feature
* Basic Service Set (BSS) usage reporting
* TID to link mapping support
* mac80211 hardware flag to disallow puncturing
iwlwifi
* new debugfs file fw_dbg_clear
mt76
* NVMEM EEPROM improvements
* mt7996 Extremely High Throughpu (EHT) improvements
* mt7996 Wireless Ethernet Dispatcher (WED) support
* mt7996 36-bit DMA support
ath12k
* support one MSI vector
* WCN7850: support AP mode
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEiBjanGPFTz4PRfLobhckVSbrbZsFAmWAdRERHGt2YWxvQGtl
cm5lbC5vcmcACgkQbhckVSbrbZu0RAf+JtHgfjmUMFb54xcncLgj8ZAN82E0ThE0
bPewQDhot0QTri4s7i5Kn8PCWjk+eKEmiIK+eARM+JDyZMTlCpXs2Y92cDAGQ8KG
+LbIMRQkwOUg0HmtX3NysUG3mGAx4QTcIX/y3+GmtMZpKXMFuNy6ODuFvuWFNJrF
3XTq1qFQNnA0XqUDKHW9uareeCiOMVOsqcxNW2FAi2gqRUfQpKnU1Ukv5iOjkqE9
i53GHzeAG2WI4/YjXaTEZvibkM3jqrPcquHlul3fVuq05qkKOEuiy2UalDjgDCYp
u91vbmMpcOjhlf9GIiu2BF6K/muEUCCIjlh5oxob0k9NiKhnPUZLng==
=6Y8M
-----END PGP SIGNATURE-----
Merge tag 'wireless-next-2023-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.8
The second features pull request for v6.8. A bigger one this time with
changes both to stack and drivers. We have a new Wifi band RFI (WBRF)
mitigation feature for which we pulled an immutable branch shared with
other subsystems. And, as always, other new features and bug fixes all
over.
Major changes:
cfg80211/mac80211
* AMD ACPI based Wifi band RFI (WBRF) mitigation feature
* Basic Service Set (BSS) usage reporting
* TID to link mapping support
* mac80211 hardware flag to disallow puncturing
iwlwifi
* new debugfs file fw_dbg_clear
mt76
* NVMEM EEPROM improvements
* mt7996 Extremely High Throughpu (EHT) improvements
* mt7996 Wireless Ethernet Dispatcher (WED) support
* mt7996 36-bit DMA support
ath12k
* support one MSI vector
* WCN7850: support AP mode
* tag 'wireless-next-2023-12-18' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (207 commits)
wifi: mt76: mt7996: Use DECLARE_FLEX_ARRAY() and fix -Warray-bounds warnings
wifi: ath11k: workaround too long expansion sparse warnings
Revert "wifi: ath12k: use ATH12K_PCI_IRQ_DP_OFFSET for DP IRQ"
wifi: rt2x00: remove useless code in rt2x00queue_create_tx_descriptor()
wifi: rtw89: only reset BB/RF for existing WiFi 6 chips while starting up
wifi: rtw89: add DBCC H2C to notify firmware the status
wifi: rtw89: mac: add suffix _ax to MAC functions
wifi: rtw89: mac: add flags to check if CMAC and DMAC are enabled
wifi: rtw89: 8922a: add power on/off functions
wifi: rtw89: add XTAL SI for WiFi 7 chips
wifi: rtw89: phy: print out RFK log with formatted string
wifi: rtw89: parse and print out RFK log from C2H events
wifi: rtw89: add C2H event handlers of RFK log and report
wifi: rtw89: load RFK log format string from firmware file
wifi: rtw89: fw: add version field to BB MCU firmware element
wifi: rtw89: fw: load TX power track tables from fw_element
wifi: mwifiex: configure BSSID consistently when starting AP
wifi: mwifiex: add extra delay for firmware ready
wifi: mac80211: sta_info.c: fix sentence grammar
wifi: mac80211: rx.c: fix sentence grammar
...
====================
Link: https://lore.kernel.org/r/20231218163900.C031DC433C9@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Newest firmware has completely offloaded this logic and this command
will be deprecated soon. Based on a capability bit advertised by the
firmware, skip this command.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://msgid.link/20231207044813.e64ef70c0133.I9f47cdef2ba45f1f383b70023857376973de3a8c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This API is type unsafe and needs an extra parameter to know
what kind of station was passed, so it has two, but really it
only needs two values. Just pass the values instead of doing
this type-unsafe dance, which will also make it better to use
for multi-link.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20231011130030.aeb3bf4204cd.I5b0e6d64a67455784bc8fbdaf9ceaf03699d9ce1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
During HW restart, STA link changes happen while the link-sta is
already allocated (had been prior to the restart). Adjust the
allocation and checks to handle that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230921110726.99b7cc754b00.Iaa0503a3100250489fed8b4bdcf60e24a96d3392@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We've observed that in some botched firmware restart scenarios
when the firmware crashes again while we're reconfiguring, we
can hit NULL pointer crashes here. The underlying issue is the
botched restart which we need to fix separately, but until we
can do that, don't crash hard here.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230614123446.e47b0192c78f.I67fa9f07cd1c8b3bdc8db25f5e31c1c680c49745@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are a number of upcoming things in both the stack and
drivers that would otherwise conflict, so merge wireless to
wireless-next to be able to avoid those conflicts.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Indicate to the firmware for each station whether or not MFP
is used with this station. Note that we indicate MFP for it
before authorized since we don't know yet, and that will make
the firmware not handle should-be-protected management frames
without being able to check them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230601095201.b1052f39af4c.I1b46b751d5808e65ea3d0e7b8b38209c5aecf042@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When adding a PASN station, the non MLD API was used. This results
in assert when operating as MLD. Fix it to use the MLD API when
operating as MLD. For now, the default link is used for the added
station.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230524203151.7c35dccc8a12.I7bc78cd16d7c750f42fdd60e07e839a860d279d2@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
In iwl_mvm_mld_update_sta(), if the flow doesn't enter
for_each_sta_active_link(), the default value is returned.
Set this default to -EINVAL instead of 0 to better reflect
this.
Signed-off-by: Mukesh Sisodiya <mukesh.sisodiya@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.98b7e3aacf0b.I2fc274dd7e374ef7fac8e26d71c9cd73323da665@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We don't need to (and shouldn't) initialize the spinlock
during HW restart that was already initialized, so move
that into the correct if block. Since then we have two
consecutive if statements with the same (though inverted)
condition, unify those as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.221c22cfdf4e.I2e30113ef4bd8cb5bd9e1a69e52a95671914961c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
There are some assertions in the STA removal code that can
fail, and in that case we may leak memory since we skip
the freeing.
Fix this by freeing the dup_data earlier in the function,
we already have a check for when we free the station, and
this we don't need to do it with and without MLD API, so
it's a win all around.
Fixes: a571f5f635 ("iwlwifi: mvm: add duplicate packet detection per rx queue")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230514120631.173938681d72.Iff4b55fc52943825d6e3e28d78a24b155ea5cd22@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When allocating a new link station, initialize the ratescaling
data for it. To do that, refactor the initialization code out
into a new iwl_mvm_rs_add_sta_link() function.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.441b6a8c60fd.I34f1b3555c25aaa22cc34d1112fc3b6393a20b7c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we first add the STA before sending an authentication
frame this is false. However, in some cases such as FT or
certainly in MLO link switch scenarios, it will be true.
If it happens to be true, it causes a firmware assert (in
LMAC, 0x2528), because the same bit is used by the firmware
for tracking this setting as well as for tracking if the
management key has been installed, and then we get this
assert from the firmware when installing the MFP key as it
thinks it has already been installed.
Remove the setting for now, until the firmware disentangles
the two. We should be able to set it, in fact we should be
setting it speculatively before authentication/association,
to avoid processing management frames that should have been
protected/encrypted before the key is set.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230417113648.adbeb0e0bfed.I400d0ee3721dc4f294313be992d277ba4d9c88d9@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we switch station links, also add the code to switch
BAIDs from one station mask to the new one.
To do so, refactor the switching code a bit to have common
code for all the needed switches; will add keys next.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.40654afce24f.I0e35151f69e7513be53ddb8f008e9ab48278c352@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We are going to need this in more places than just the
key code, so factor out the functionality of getting
the FW station ID mask (filtered to a specific link if
needed) to a separate function that can now be called
both under RCU and mvm->mutex protection.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230416154301.eff92b93025d.I2c50290a0537d5db3d3460f4d57c78a4712ffb75@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
On queue remove, we should convert the TID value to the
firmware value (8 -> 15) just like we do on queue add.
Otherwise, the firmware will not be able to find the
correct queue to remove.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230413102635.6651077eaec3.Ia6868c8fc1a92063609bb057b6a618726712d0bb@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
This function can be invoked for both MLO and non-MLO, so
it must deal with multi-link correctly. Notable, on auth
timeout, we'd otherwise get a warning due to the erroneous
deflink usage in MLO cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230329100040.b85f6052d51a.Iedfef4b4c4f3ca557aebc0093fdc3f5cfb49b507@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The link management queues associated with the broadcast stations
were forgotten and so the same queue was used with both broadcast
stations. This leads to lost frames and warnings on cleanup and
HW restart.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230329100040.0671fa976832.Id5aa9856fd5984e447f247e6d0c3979d9794a21a@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
By using the internal station add the station is installed in
firmware with zeroed MAC addresses, which is wrong. Use the
full installation function instead, to fill all data.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230329100040.62d5371bb3c7.Ie25b62125a3a022f76a36bae5fed9796c18698aa@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
When we remove the station, we call iwl_mvm_sta_del() which
returns true if we cannot remove it from the firmware yet,
which happens if this is the station ID for the AP station
that's still used because the MAC is still associated.
However, we still must free the link data as the station is
only kept alive in the firmware, in mac80211 and driver the
data structures are destroyed.
To fix that, we need to make iwl_mvm_mld_free_sta_link()
track whether or not the station is still alive in FW, as
otherwise we might reuse the station ID in the meantime and
iwl_mvm_mld_rm_sta_from_fw() would reject the later delete
from the firmware. Add an argument to it for that. Then we
can use the return value of iwl_mvm_sta_del() for that to
fix the issue, and call iwl_mvm_mld_rm_sta_from_fw() only
if we need to not keep the station in FW.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230329100039.1d81d4c71f35.I8fc60ac28ffc1147e9b1250e5e6237b3cb5516ac@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Use the new macros from mac80211 that do lockdep checking
on the RCU dereferences, instead of hard-coding 1 as the
argument to rcu_dereference_protected().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230329100039.112df5c8dec2.I1a1008f5566e509953d988f254d15c9e58630418@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add a fw_id_to_link_sta array in mvm to track the link
STA for each firmware station ID, and then use that to
report the link a frame was received on (since we know
the station ID from firmware).
Notably, this fixes beacon tracking for the correct link
since mac80211 now queues and processes those on the one
link identified by the link ID only.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230329100039.c7dd3ec18077.I12ef9eb4a5b8b5c2b9d6bcaa1fda73b59eba39d8@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Add/removed from iwl driver and firmware station links.
Update the station queues accordingly (which station links
are connected to the station queues).
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230329100039.156d1aae5de1.I32973141be1190222169879f8caf7038c1a8f769@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Replace the deflink.addr with the proper link address
for setting the peer_link_address in the station command.
For a non-MLD station, it will be the deflink.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230329100039.03ab287da0ae.I88fb5ab4e3ea9c886a3fac7ce09c4791469c3c8e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
For now we only support a single link, so just use the
deflink's address for the link address, instead of the
STA's (MLD) address, but use the link address anyway
in order to facilitate MLO connections.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230329100039.c853c8ced3ba.I2e1915d1090c526e6a4c718440b45a7192bbbb03@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Driver uses link_id as an index in the array. FW currently can
support only 2 concurrently active links per vif with the ids in the
range 0-3. Add a mapping of dirver link ids to fw link id and track the
number of active link ids.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230328104949.a53e5df49c33.I02b25648d2d5ca370c0697bf19d0d34724eae8a1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The LINK cmd host api has been updated. Align the driver to the
new changes. Also, temporary use mac_id for link_id.
Using the phy_id as the link_id is wrong since we might have 2 macs
operating on the same phy - in this case we will have 2 different
links (one for each mac) with the same link_id. On the other hand,
since we don't have MLO implemented yet, we won't have 2 different
links of the same mac. Therefore, we can use the mac_id as the
link_id.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230328104948.78ae716884fe.Icfeb2794d9652baaccf9b0cdddbd751d0db4f952@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently we're setting the sta->addr as the peers address only if
the iftype is NL80211_IFTYPE_AP, otherwise we are setting the bssid to
be the addr. This causes bugs in TDLS. Fix this by always using the
sta->addr.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230328104948.4c104c3074c4.I78912bb85251033e60db99a65165890779203612@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The patch linked below fixes the crash on queue removal bug only
for the non-MLD API. Do the same for the MLD API.
Fixes: c5a976cf6a ("wifi: iwlwifi: modify new queue allocation command")
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230328104948.527dace26147.Ia215df5833634f95688a979f39fae70c1ac4e027@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
These flows are the same in both MLD API and the current API,
except for the commands that are being sent during this flows.
Instead of checking each time before calling these floews
what API we use and then call the correct function, call always the old
one, which in turn will call the new one in case we're using the MLD
API.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230328104948.5692d8dea9be.Ib1882b2c2f0b0603abc4b7d4a0ecc45cd1fbf9a7@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
