Even if it is not a real issue at the moment since concurrent access to
mcu message queue is protected by mcu mutex, make the code more robust
and move mcu queue free space check inside queue spinlock critical section.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During chip recovery (e.g. chip reset), there is a possible situation that
kernel worker reset_work is holding the lock and waiting for kernel thread
stat_worker to be parked, while stat_worker is waiting for the release of
the same lock.
It causes a deadlock resulting in the dumping of hung tasks messages and
possible rebooting of the device.
This patch prevents the execution of stat_worker during the chip recovery.
Signed-off-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Ming Yen Hsieh <MingYen.Hsieh@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
When queueing packets, only the MT76_RESET flag of the primary PHY
is checked. If the primary PHY is scanning or changing channels, this can
lead to packet loss for tx on the second PHY.
Fix this by passing the phy to the .tx_queue_skb op and using it to check
the correct flag.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The ieee80211_queue_work function queues work into the mac80211
local->workqueue, which is widely used for mac80211 internal
work processes. In the mt76 driver, both the mt76-sido-status and
mt76-sdio-net threads enqueue workers to the workqueue with this
function. However, in some cases, when two workers are enqueued
to the workqueue almost simultaneously, the second worker may not
be scheduled immediately and may get stuck for a while.
This can cause timing issues. To avoid these timing
conflicts caused by worker scheduling, replace the worker
with an independent thread.
Fixes: 48fab5bbef ("mt76: mt7921: introduce mt7921s support")
Signed-off-by: Wang Zhao <wang.zhao@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Ensure the entry has been fully updated before SDIO bus worker access
it. This patch would fix potential memory risk in both mt7663s and
mt7921s.
Fixes: 764dee47e2 ("mt76: sdio: move common code in mt76_sdio module")
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to introduce WED RX support for mt7915.
Tested-by: Daniel Golle <daniel@makrotopia.org>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sujuan Chen <sujuan.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Fix transmitting packets hangs with continuing to pull the pending packet
from mac80211 queues when receiving Tx status notification from the device.
Fixes: aac5104bf6 ("mt76: sdio: do not run mt76_txq_schedule directly")
Acked-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: YN Chen <yn.chen@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
It is not meaningful to poll sta stat when there is no data traffic.
So polling sta stat when the device has transmitted data instead to save
CPU power.
That implies that it is unallowed the stat_work to work while MCU is being
initialized in the really early stage to fix the possible time to time MCU
initialization failure.
Fixes: d39b52e31a ("mt76: introduce mt76_sdio module")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Because wake_work and sdio->stat_work share the same workqueue mt76->wq,
if sdio->stat_work cannot acquire the mutex lock such as that was possibly
held up by [mt7615, mt7921]_mutex_acquire. Additionally, if
[mt7615, mt7921]_mutex_acquire was called by sdio->stat_work self, the wake
would be blocked by itself. Thus, we move the stat_work into
ieee80211_workqueue instead to break the deadlock.
Fixes: d39b52e31a ("mt76: introduce mt76_sdio module")
Co-developed-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: YN Chen <YN.Chen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
We don't have to create a separate sdio.xmit_buf buffer for each queue.
Instead, we just need to create one, reuse it across all queues to reduce
memory consumption further.
And then we should take it into account the actual the host and the device
MMC capability to determine what the appropriate xmit_buf_size can be.
Both MT7921S and MT7663 can support up to Tx FIFO size of 0x3fe00 which
means the device can receive 511 blocks of block size 512 in a row from
the host. So if the driver aggregates the frames as many as possible the
the device can support, we can merge multiple MMC requests into a single
one to get rid of the overhead of the handling and synchronizing in those
unnecessary MMC requests and reduce the SDIO lock contention with the
Bluetooth concurrent traffic and finally to have the higher bus
utilization with less idle cycle.
With the patch, it is helpful for WiFi to have steady throughput
performance especially while running Bluetooth concurrently.
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
During heavy loading throughtput test, the RX buffer (128)
would be exhausted and some RX pkts dropped randomly. Increase
buffer size from 128 to 512 (a safer length) to avoid tput degrade
or cmd-timeout problem.
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
According to the MT7921S firmware, the cmd MCU_UNI_CMD_HIF_CTRL have to
be last MCU command to execute in suspend handler and all data traffic
have to be stopped before the cmd MCU_UNI_CMD_HIF_CTRL starts as well
in order that mt7921 can successfully fall into the deep sleep mode.
Where we reuse the flag MT76_STATE_SUSPEND and avoid creating
another global flag to stop all of the traffic onto the SDIO bus.
Fixes: 48fab5bbef ("mt76: mt7921: introduce mt7921s support")
Reported-by: Leon Yen <leon.yen@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Extend sdio module to support CONNAC2 hw that mt7921s rely on.
Tested-by: Deren Wu <deren.wu@mediatek.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Co-developed-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Deren Wu <deren.wu@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move sdio common code in mt76_sdio module.
This is a preliminary patch to support mt7921s devices.
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Export mt76s_alloc_rx_queue and mt76s_alloc_tx utility routines in order
to allow mt7921s driver to configure a different main rx queue.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Remove mt76_wcid pointer from mt76_tx_status_check signature since it is
always set to NULL
Tested-by: mrkiko.rs@gmail.com
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to support runtime-pm for sdio, do not run mt76_txq_schedule
directly, but schedule tx_worker instead
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use the additional memory barrier to ensure the skb list up-to-date
between the skb producer and consumer to avoid the invalid skb content
written into sdio controller and then cause device hang due to mcu assert
caught by WR_TIMEOUT_INT.
Fixes: 1522ff731f ("mt76: mt7663s: introduce sdio tx aggregation")
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Similar to mmio/usb code path, remove wake logic in mt76s_process_tx_queue
routine. Starting from commit 90d494c99a ("mt76: improve tx queue
stop/wake"), the wake queue logic on the sdio status path is no longer
necessary since the hw queues are no longer stopped on the mt76 tx path.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/d2d7d9d437f4dec2ef1df0ed070b9cf299f021ad.1607164041.git.lorenzo@kernel.org
Move hw data queues in mt76_phy from mt76_dev since mt7915 supports per
phy hw queues in dbdc mode
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mcu queue to a dedicated array q_mcu in mt76_dev structure.
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Rely on mt76_queue instead of qid in tx_queue_skb signature.
This is a preliminary patch to move data queues in mt76_phy and add
dbdc support to mt7915 driver
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move data queues in mt76_phy and properly
support dbdc for mt7915
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This is a preliminary patch to move hw data queues in mt76_phy for
mt7915 dbdc support
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
sched quota is now updated in mt7663s_txrx_worker so there is no more
need of sched.lock mutex
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to improve driver throughput, convert status_work and net_work
to mt76 worker APIs.
Remove txrx_wq sdio workqueue since it is no longer used
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to improve driver throughput, convert txrx_work to mt76 worker
threads APIs.
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move mt7663 tx and rx processing in the same workqueue in order to
reduce jitter that can hit tcp performances. This is a preliminary patch
to switch to mt76 workers APIs
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move frame pad computation out of mt76_skb_adjust_pad routine.
This is a preliminary patch to introduce sdio tx aggregation.
Tested-by: Sean Wang <sean.wang@mediatek.com>
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Now that AQL works well on all mt76 drivers, completely replace the arbitrary
burst sizing and number of bursts logic for tx scheduling.
For the short period of time in which AQL does not work well yet, limit each
stations to 16 in-flight packets that have no estimated tx time.
This should avoid filling the queue if a station connects and queues up a
large number of packets before rate control information is available, especially
with hardware rate control
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to maximize parallelism, split status work in tx status work
and rx net work
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
As it has been done for tx and rx processing, move tx/rx status
processing into mt76s_txrx_wq workqueue
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Move rx processing to mt76s_txrx_wq in order to minimize the interval when
the sdio bus is locked during rx
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76s_txrx_wq workqueue and move tx processing from kthread to
a dedicated work. This is preliminary patch to improve mt7663s throughput
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Free the mcu skb in case of error in mt76s_tx_queue_skb_raw routine
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In order to avoid possible overflows, move tx queue accounting from
mt7663s_tx_run_queue() to mt76s_tx_queue_skb_raw()/mt76s_tx_queue_skb()
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_sdio module as common layer to add mt7663s support
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
