Since commit 0a44dfc070 ("wifi: mac80211: simplify non-chanctx
drivers") ieee80211_hw_config() is no longer called with changed = ~0.
rtlwifi relied on ~0 in order to ignore the default retry limits of
4/7, preferring 48/48 in station mode and 7/7 in AP/IBSS.
RTL8192DU has a lot of packet loss with the default limits from
mac80211. Fix it by ignoring IEEE80211_CONF_CHANGE_RETRY_LIMITS
completely, because it's the simplest solution.
Link: https://lore.kernel.org/linux-wireless/cedd13d7691f4692b2a2fa5a24d44a22@realtek.com/
Cc: stable@vger.kernel.org # 6.9.x
Signed-off-by: Bitterblue Smith <rtl8821cerfe2@gmail.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://msgid.link/1fabb8e4-adf3-47ae-8462-8aea963bc2a5@gmail.com
There are still surprisingly many non-chanctx drivers, but in
mac80211 that code is a bit awkward. Simplify this by having
those drivers assign 'emulated' ops, so that the mac80211 code
can be more unified between non-chanctx/chanctx drivers. This
cuts the number of places caring about it by about 15, which
are scattered across - now they're fewer and no longer in the
channel context handling.
Link: https://msgid.link/20240129194108.6d0ead50f5cf.I60d093b2fc81ca1853925a4d0ac3a2337d5baa5b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Since there is no chip-specific code behind 'chk_switch_dmdp()',
there is no need to maintain function pointer in 'struct rtl_hal_ops'
and relevant common code may be simplified. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231016135925.129223-3-dmantipov@yandex.ru
Since 'rtlpriv->cfg->ops->fill_tx_cmddesc()' is always called
with 'firstseg' and 'lastseg' set to 1 (and the latter is
never actually used), all of the relevant chip-specific
routines may be simplified. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231011154442.52457-2-dmantipov@yandex.ru
Use eth_broadcast_addr() to assign broadcast address instead
of memcpy().
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230804090120.1332091-1-yangyingliang@huawei.com
Introduce 'rtl_init_sw_leds()' to replace per-chip LED
initialization code (and so drop 'struct rtl_led' as no
longer used), drop 'init_sw_leds' and 'deinit_sw_leds'
fields from 'struct rtl_hal_ops', adjust related code.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614061832.40882-1-dmantipov@yandex.ru
mac80211 is fully switching over to the internal TX queue (iTXQ)
implementation. Update all drivers not yet providing the now mandatory
wake_tx_queue() callback.
As an side effect the netdev interfaces of all updated drivers will
switch to the noqueue qdisc.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[add staging drivers]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pass the link id through to the get_beacon and return
the beacon for a specific link id.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Split the bss_info_changed method to vif_cfg_changed and
link_info_changed, with the latter getting a link ID.
Also change the 'changed' parameter to u64 already, we
know we need that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
We'll use bss_conf for per-link configuration later, so
move out all the non-link-specific data out into a new
struct ieee80211_vif_cfg used in the vif.
Some adjustments were done with the following spatch:
@@
expression sdata;
struct ieee80211_vif *vifp;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
(
-sdata->vif.bss_conf.var
+sdata->vif.cfg.var
|
-vifp->bss_conf.var
+vifp->cfg.var
)
@bss_conf@
struct ieee80211_bss_conf *bss_conf;
identifier var = { assoc, ibss_joined, aid, arp_addr_list, arp_addr_cnt, ssid, ssid_len, s1g, ibss_creator };
@@
-bss_conf->var
+vif_cfg->var
(though more manual fixups were needed, e.g. replacing
"vif_cfg->" by "vif->cfg." in many files.)
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently in mac80211 each STA object is represented
using sta_info datastructure with the associated
STA specific information and drivers access ieee80211_sta
part of it.
With MLO (Multi Link Operation) support being added
in 802.11be standard, though the association is logically
with a single Multi Link capable STA, at the physical level
communication can happen via different advertised
links (uniquely identified by Channel, operating class,
BSSID) and hence the need to handle multiple link
STA parameters within a composite sta_info object
called the MLD STA. The different link STA part of
MLD STA are identified using the link address which can
be same or different as the MLD STA address and unique
link id based on the link vif.
To support extension of such a model, the sta_info
datastructure is modified to hold multiple link STA
objects with link specific params currently within
sta_info moved to this new structure. Similarly this is
done for ieee80211_sta as well which will be accessed
within mac80211 as well as by drivers, hence trivial
driver changes are expected to support this.
For current non MLO supported drivers, only one link STA
is present and link information is accessed via 'deflink'
member.
For MLO drivers, we still need to define the APIs etc. to
get the correct link ID and access the correct part of
the station info.
Currently in mac80211, all link STA info are accessed directly
via deflink. These will be updated to access via link pointers
indexed by link id with MLO support patches, with link id
being 0 for non MLO supported cases.
Except for couple of macro related changes, below spatch takes
care of updating mac80211 and driver code to access to the
link STA info via deflink.
@ieee80211_sta@
struct ieee80211_sta *s;
struct sta_info *si;
identifier var = {supp_rates, ht_cap, vht_cap, he_cap, he_6ghz_capa, eht_cap, rx_nss, bandwidth, txpwr};
@@
(
s->
- var
+ deflink.var
|
si->sta.
- var
+ deflink.var
)
@sta_info@
struct sta_info *si;
identifier var = {gtk, pcpu_rx_stats, rx_stats, rx_stats_avg, status_stats, tx_stats, cur_max_bandwidth};
@@
(
si->
- var
+ deflink.var
)
Signed-off-by: Sriram R <quic_srirrama@quicinc.com>
Link: https://lore.kernel.org/r/1649086883-13246-1-git-send-email-quic_srirrama@quicinc.com
[remove MLO-drivers notes from commit message, not clear yet; run spatch]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Once beacon content is changed, we update the content to wifi card by
send_beacon_frame(). Then, STA with PS can wake up properly to receive its
packets.
Since we update beacon content to PCI wifi devices every beacon interval,
the only one usb device, 8192CU, needs to update beacon content when
mac80211 calling set_tim.
Reported-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Tested-by: Maciej S. Szmigiero <mail@maciej.szmigiero.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20210419065956.6085-1-pkshih@realtek.com
rtl_lps_enter() and rtl_lps_leave() are using in_interrupt() to detect
whether it is safe to acquire a mutex or if it is required to defer to a
workqueue.
The usage of in_interrupt() in drivers is phased out and Linus clearly
requested that code which changes behaviour depending on context should
either be seperated or the context be conveyed in an argument passed by the
caller, which usually knows the context.
in_interrupt() also is only partially correct because it fails to chose the
correct code path when just preemption or interrupts are disabled.
Add an argument 'may_block' to both functions and adjust the callers to
pass the context information.
The following call chains were analyzed to be safe to block:
rtl_watchdog_wq_callback()
rlf_lps_leave/enter()
rtl_op_suspend()
rtl_lps_leave()
rtl_op_bss_info_changed()
rtl_lps_leave()
rtl_op_sw_scan_start()
rtl_lps_leave()
The following call chains were analyzed to be unsafe to block:
_rtl_pci_interrupt()
_rtl_pci_rx_interrupt()
rtl_lps_leave()
_rtl_pci_interrupt()
_rtl_pci_rx_interrupt()
rtl_is_special_data()
rtl_lps_leave()
_rtl_pci_interrupt()
_rtl_pci_rx_interrupt()
rtl_is_special_data()
setup_special_tx()
rtl_lps_leave()
_rtl_pci_interrupt()
_rtl_pci_tx_isr
rtl_lps_leave()
halbtc_leave_lps()
rtl_lps_leave()
This leaves four callers of rtl_lps_enter/leave() where the analyzis
stopped dead in the maze of several nested pointer based callchains and
lack of rtlwifi hardware to debug this via tracing:
halbtc_leave_lps(), halbtc_enter_lps(), halbtc_normal_lps(),
halbtc_pre_normal_lps()
These four have been cautionally marked to be unable to block which is the
safe option, but the rtwifi wizards should be able to clarify that.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro name RT_TRACE makes it seem that it is used for tracing, when
is actually used for debugging. Change the name to rtl_dbg. Any Sparse
errors exposed by this change were also fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200723204244.24457-3-Larry.Finger@lwfinger.net
The variable 'rtlpriv->rfkill.rfkill_state' is bool and can directly
assigned to bool values.
Fix the following coccicheck warning:
drivers/net/wireless/realtek/rtlwifi/core.c:1725:14-42: WARNING:
Comparison of 0/1 to bool variable
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200429140924.7750-1-yanaijie@huawei.com
The types of problems fixed are as follows:
WARNING: Missing a blank line after declarations
CHECK: Please use a blank line after function/struct/union/enum declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When no beacon was received, the value in dm.undec_sm_pwdb is most
likely out of date and should not be used to adjust the input path.
Assume instead that the signal level is low.
Fix the state machine in rtl8723e_dm_cck_packet_detection_thresh
which did not clear pre_cck_fa_state when changing cur_cck_pd_state
from CCK_PD_STAGE_LOWRSSI/CCK_FA_STAGE_LOW to CCK_PD_STAGE_HIGHRSSI
and back again to CCK_PD_STAGE_LOWRSSI/CCK_FA_STAGE_LOW, the register
RCCK0_CCA not written to 0x83 on the second change.
Explicitly initialize pre_cck_fa_state/cur_cck_fa_state in
rtl_dm_diginit.
Signed-off-by: Bernd Edlinger <bernd.edlinger@hotmail.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this patch, firmware will not run properly on rtl8821ae, and it
causes bad user experience. For example, bad connection performance with
low rate, higher power consumption, and so on.
rtl8821ae uses two kinds of firmwares for normal and WoWlan cases, and
each firmware has firmware data buffer and size individually. Original
code always overwrite size of normal firmware rtlpriv->rtlhal.fwsize, and
this mismatch causes firmware checksum error, then firmware can't start.
In this situation, driver gives message "Firmware is not ready to run!".
Fixes: fe89707f0a ("rtlwifi: rtl8821ae: Simplify loading of WOWLAN firmware")
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Cc: Stable <stable@vger.kernel.org> # 4.0+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When connecting to AP, mac80211 asks driver to enter and leave PS quickly,
but driver deinit doesn't wait for delayed work complete when entering PS,
then driver reinit procedure and delay work are running simultaneously.
This will cause unpredictable kernel oops or crash like
rtl8723be: error H2C cmd because of Fw download fail!!!
WARNING: CPU: 3 PID: 159 at drivers/net/wireless/realtek/rtlwifi/
rtl8723be/fw.c:227 rtl8723be_fill_h2c_cmd+0x182/0x510 [rtl8723be]
CPU: 3 PID: 159 Comm: kworker/3:2 Tainted: G O 4.16.13-2-ARCH #1
Hardware name: ASUSTeK COMPUTER INC. X556UF/X556UF, BIOS X556UF.406
10/21/2016
Workqueue: rtl8723be_pci rtl_c2hcmd_wq_callback [rtlwifi]
RIP: 0010:rtl8723be_fill_h2c_cmd+0x182/0x510 [rtl8723be]
RSP: 0018:ffffa6ab01e1bd70 EFLAGS: 00010282
RAX: 0000000000000000 RBX: ffffa26069071520 RCX: 0000000000000001
RDX: 0000000080000001 RSI: ffffffff8be70e9c RDI: 00000000ffffffff
RBP: 0000000000000000 R08: 0000000000000048 R09: 0000000000000348
R10: 0000000000000000 R11: 0000000000000001 R12: 0000000000000000
R13: ffffa26069071520 R14: 0000000000000000 R15: ffffa2607d205f70
FS: 0000000000000000(0000) GS:ffffa26081d80000(0000) knlGS:000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00000443b39d3000 CR3: 000000037700a005 CR4: 00000000003606e0
Call Trace:
? halbtc_send_bt_mp_operation.constprop.17+0xd5/0xe0 [btcoexist]
? ex_btc8723b1ant_bt_info_notify+0x3b8/0x820 [btcoexist]
? rtl_c2hcmd_launcher+0xab/0x110 [rtlwifi]
? process_one_work+0x1d1/0x3b0
? worker_thread+0x2b/0x3d0
? process_one_work+0x3b0/0x3b0
? kthread+0x112/0x130
? kthread_create_on_node+0x60/0x60
? ret_from_fork+0x35/0x40
Code: 00 76 b4 e9 e2 fe ff ff 4c 89 ee 4c 89 e7 e8 56 22 86 ca e9 5e ...
This patch ensures all delayed works done before entering PS to satisfy
our expectation, so use cancel_delayed_work_sync() instead. An exception
is delayed work ips_nic_off_wq because running task may be itself, so add
a parameter ips_wq to deinit function to handle this case.
This issue is reported and fixed in below threads:
https://github.com/lwfinger/rtlwifi_new/issues/367https://github.com/lwfinger/rtlwifi_new/issues/366
Tested-by: Evgeny Kapun <abacabadabacaba@gmail.com> # 8723DE
Tested-by: Shivam Kakkar <shivam543@gmail.com> # 8723BE on 4.18-rc1
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Fixes: cceb0a5973 ("rtlwifi: Add work queue for c2h cmd.")
Cc: Stable <stable@vger.kernel.org> # 4.11+
Reviewed-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Originally, btcoex controls the antenna of combo card, but solo card
is also needed to setup properly. The new ops are named with suffix
'_wifi_only' opposited to original btc_ops, and new structures and
definitions are also introduced. The wifi_only oly contains four ops that
are initial variable, hw config, scan notify, and switch band notify.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When AP change bandwidth setting from 20M to 40M, STA may use old 20M AP
information to association with AP. Driver unlink bss in the
.bss_info_changed of ieee80211_ops to make sure that later scan can get
correct AP bandwidth capability.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is merged by Ping-Ke Shih from commit a221cb0911 ("staging:
rtlwifi: Remove unnecessary parentheses"), and original commit log
is reserved below.
Remove unnecessary parentheses to comply with preferred coding style for
the linux kernel and avoid the following checkpatch's message:
'CHECK: Unnecessary parentheses around'.
Credits to checkpatch.
Signed-off-by: Frank A. Cancio Bello <frank@generalsoftwareinc.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is merged by Ping-Ke Shih from commit 688a0206cf ("staging:
rtlwifi: fix parenthesis alignment"), and original commit log is
reserved below.
Checkpatch emits multiple warnings of type
CHECK:PARENTHESIS_ALIGNMENT: Alignment should match open parenthesis
Fix parenthesis alignment in line with checkpatch suggestion.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
cfg_cmd is initialized to zero and this value is never read, instead
it is over-written in the start of a do-while loop. Remove the
redundant initialization. Cleans up clang warning:
drivers/net/wireless/realtek/rtlwifi/core.c:1750:22: warning: Value
stored to 'cfg_cmd' during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
do_gettimeofday() is deprecated and slower than necessary for the purpose
of reading the seconds. This changes rtl_op_suspend/resume to use
ktime_get_real_seconds() instead, which is simpler and avoids confusion
about whether it is y2038-safe or not.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Cc: Arvind Yadav <arvind.yadav.cs@gmail.com>
Cc: Souptick Joarder <jrdr.linux@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
- Add new parameter "is_bw_update" to control if current bandwidth setting
is updated to FW RA.
- After this commit, we keep the same setting as before.
- Later, bandwidth update in watchdog is changed to false for 8822BE.
Signed-off-by: Tsang-Shian Lin <thlin@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My static checker complains that we have an upper bound but no lower
bound. I suspect neither are really required but it doesn't hurt to add
a check for negatives.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Because it isn't always correct to use EAPOL to check 4-way,
we add a timer to handle exception.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When using EAPOL to do a PTK rekey, there is a possible race condition.
When msg 3/4 is received, the supplicant will send msg 4/4 and install
the new key immediately; however, the driver must make sure that msg 4/4
is sent before installing the new key. We use TX report to ensure it is
sent.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since the driver itself will enter power saving mode dynamically
according to the traffic, we set hw capability SUPPORTS_PS and
SUPPORTS_DYNAMIC_PS in case of fwctrl_lps.
The process IEEE80211_CONF_CHANGE_PS in op_config is used by
SW-LPS only, so we add constraints to avoid errors.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: vincent_fann <vincent_fann@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Yan-Hsuan Chuang <yhchuang@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We assign different retry limit according to vif type, because
it can boost performance in field.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: shaofu <shaofu@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYalDTAAoJEG4XJFUm622ba2EH/ivoHG9CvmT6HgNw77odDr6b
Zc7plDi2dd9LIzp3rF/9j8Ietfzpu31Pp9Qz0o1Su/s8RJIlXKVF5UeG5IignnEG
02rv7Z+BGPW7SUNDb0cLa27PMYqUAh8vI39sxYSdQ9NQLIlpMLIxxx5iOZyAK5eV
HBRS0pVlSxbAntb1JgWiN/LjjXe/PdhX3CR/b9b468KAcWB6UWj9nXQxFmz7d3uM
dH3buDTgwaq7K24ZAFc1BsD7rgxprpauXxgIMWCKxRERf64WFfYkYdfdCER+PSPH
maV5Te1KzTJBrQHDOPs1ezVe8gDUhb5YE4BJY9SppZpOE1arucq2g3+3obQUeHE=
=DAVq
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-01-02' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.11
The most notable change here is the inclusion of airtime fairness
scheduling to ath9k. It prevents slow clients from hogging all the
airtime and unfairly slowing down faster clients.
Otherwise smaller changes and cleanup.
Major changes:
ath9k
* cleanup eeprom endian handling
* add airtime fairness scheduling
ath10k
* fix issues for new QCA9377 firmware version
* support dev_coredump() for firmware crash dump
* enable channel 169 on 5 GHz band
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
trivial fix to spelling mistake in RT_TRACE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
These messages are always logged and represent error conditions, thus
we can use pr_err().
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This macro can be replaced with WARN_ONCE. In addition to using a
standard debugging macro for these critical errors, we also get
a stack dump.
In rtl8821ae/hw.c, a senseless comment was removed, and an incorrect
indentation was fixed.
This patch also fixes two places in each of rtl8192ee, rtl8723be,
and rtl8821ae where the logical condition was incorrect.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With commit e496561473 {"rtlwifi: Use dev_kfree_skb_irq instead of
kfree_skb"), the method used to free an skb was changed because the
kfree_skb() was inside a spinlock. What was forgotten is that kfree_skb()
guards against a NULL value for the argument. Routine dev_kfree_skb_irq()
does not, and a test is needed to prevent kernel panics.
Fixes: e496561473 ("rtlwifi: Use dev_kfree_skb_irq instead of kfree_skb")
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.9+
Cc: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYQGivAAoJEG4XJFUm622bqG0IAJtSGt4Fxv2jL7GPmPpEUtYK
F6G1PCk9LxO44rOZ15E/CT1vPk6Bnwqp9brdngmXwl7jc+jGs4MQN7g6cD4UZgPm
gxjx8cah2HPRVgEE7PeOILthRxwPA+9klycsvwtglkgQ1SpQVmLHDTLpeOAkRluY
olJGINoGHTD6osud6p3oKK+VP891omJvu8TPqRjhrhLhbQTWAuTxl2Gsdye30yag
CsdaEZb9wdUEBoS80EVRwvgBzqrdKU5kGDGbuzytcyrFrRHo4flti1KgxDg3nIpI
jC4Liwg0yE/aYZlfMqi/960rt8AttCJBDt/vwqp0mOE4IwFsE9Yaio6xXUonAC8=
=a6a/
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-12-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
rsi
* filter rx frames
* configure tx power
* make it possible to select antenna
* support 802.11d
brcmfmac
* cleanup of scheduled scan code
* support for bcm43341 chipset with different chip id
* support rev6 of PCIe device interface
ath10k
* add spectral scan support for QCA6174 and QCA9377 families
* show used tx bitrate with 10.4 firmware
wil6210
* add power save mode support
* add abort scan functionality
* add support settings retry limit for short frames
bcma
* add Dell Inspiron 3148
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit a5ffbe0a19 ("rtlwifi: Fix scheduling while atomic bug") and
commit a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter()
to use work queue"), an error was introduced in the power-save routines
due to the fact that leaving PS was delayed by the use of a work queue.
This problem is fixed by detecting if the enter or leave routines are
in interrupt mode. If so, the workqueue is used to place the request.
If in normal mode, the enter or leave routines are called directly.
Fixes: a269913c52 ("rtlwifi: Rework rtl_lps_leave() and rtl_lps_enter() to use work queue")
Reported-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJYOAC4AAoJEG4XJFUm622bUYkH/3SSYp6moSdKpVnVPx7ST7yK
t9WHR9IMZFIhD6vq8AK6+8OQr1TgGjHfPu+WZj7CIl8nu53kcgPRi51gg1mndbNg
9N3RbVp06nGbM2VnW8ZIpg3OLIXatZ4c9g3LFvvtyobYvWGJ6W4D79JdlmTG1ELr
XAjInbxFsgon+CwqCMOaAJx8xYp42rBnPRZZvhOq9O33kRw8Umo9UQw0s1U2Vfgx
prxQ6d0GxNAPEe8QiDw/vtBcXWFMOhQeDl8sK70ZcojSn1FY730NsIh/Y86PcQTK
6TsvOL5gg+rd0ln8TZRAslnDrZBAhTEDqUzLQMRJ9VjEj5RFd8eLCSIzHfaroI8=
=4qCH
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2016-11-25' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.10
Major changes:
iwlwifi
* finalize and enable dynamic queue allocation
* use dev_coredumpmsg() to prevent locking the driver
* small fix to pass the AID to the FW
* use FW PS decisions with multi-queue
ath9k
* add device tree bindings
* switch to use mac80211 intermediate software queues to reduce
latency and fix bufferbloat
wl18xx
* allow scanning in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not allowed to call kfree_skb() from hardware interrupt
context or with interrupts being disabled, spin_lock_irqsave()
make sure always in irq disable context. So the kfree_skb()
should be replaced with dev_kfree_skb_irq().
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit d86e647688 ("rtlwifi: rtl818x: constify local structures"),
the configuration struct for most of the drivers was changed to be
constant. The problem is that five of the modified drivers need to be
able to update the firmware name based on the exact model of the card.
As the file names were stored in one of the members of that struct,
these drivers would fail with a kernel BUG splat when they tried to
update the firmware name.
Rather than reverting the previous commit, I used a suggestion by
Johannes Berg and made the firmware file name pointers be local to
the routines that update the software variables.
The configuration struct of rtl8192cu, which was not touched in the
previous patch, is now constantfied.
Fixes: d86e647688 ("rtlwifi: rtl818x: constify local structures")
Suggested-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> # 4.8
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
