LB_EN for prune switch rules was causing all TX traffic
to loopback to the internal switch and dropped. When
running bi-directional stress workloads with RDMA
the RDPU would hang blocking tx and rx traffic.
Signed-off-by: Christopher N Bednarz <christopher.n.bednarz@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In VEB mode, enable LAN_EN bit in the action fields for filter rules
corresponding to the right recipes.
Signed-off-by: Yashaswini Raghuram Prathivadi Bhayankaram <yashaswini.raghuram.prathivadi.bhayankaram@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Implement support for VF promiscuous mode, MAC/VLAN/MAC_VLAN and PF
multicast MAC/VLAN/MAC_VLAN promiscuous mode.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch does some clean up in the Tx scheduler code:
1. Adjust the stack variable usage
2. Modify the debug prints to display the FW error
3. Add additional debug prints while adding/removing VSIs
Signed-off-by: Victor Raj <victor.raj@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Remove unused vsi_id field from struct ice_sched_vsi_info.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Put the return type on a separate line for function prototypes and
signatures that would exceed the 80-character limit if both were on
the same line.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Static analysis flagged a potential divide by zero error because
vsi->num_rxq can become zero in certain condition and it is used as
divisor.
Signed-off-by: Kiran Patil <kiran.patil@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When VF requested for queues changes, we need to update LAN Tx queue with
correct number of VF queue pairs and re-allocate VF resources based on
this new requested number of queues, which is constraint within maximum
queue supported per VF.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 7c710869d6 ("ice: Add handlers for VF netdevice operations")
seems to have inadvertently introduced a function prototype for
ice_set_vf_bw that isn't implemented. Remove it.
Fixes: 7c710869d6 ("ice: Add handlers for VF netdevice operations")
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
cppcheck warns "Identical condition '<var>', second condition is always
false". Fix them.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes issue reclaiming VF resources back to the pool after
reset - Since we only allocate HW vector for all VFs and track together
with resources allocation for PF with ice_search_res, we need to free VFs
resources separately, using first VF vector index to traverse the list.
Otherwise tracker starts from the last assigned vectors list and causes
maximum supported number of HW vectors, 1024 to be exhausted, depending on
the number of VFs enabled, which causes a lot of unwanted issues, and
failed to reassign vectors for VFs.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch enables MAC anti-spoof by default, with creation of VF VSIs or
when the VF VSIs are being re-initialized.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently we set the default number of Tx and Rx descriptors to 128 by
default. For Rx this amounts to a full page (assuming 4K pages) because
each Rx descriptor is 32 Bytes, but for Tx it only amounts to a half
page because each Tx descriptor is 16 Bytes (assuming 4K pages).
Instead of assuming 4K pages, determine the ring size and the number of
descriptors for Tx and Rx based on a calculation using the PAGE_SIZE,
ICE_MAX_NUM_DESC, and ICE_REQ_DESC_MULTIPLE. This change is being made
to improve the performance of the driver when using the default
settings.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
During SR-IOV initialization, we allocate and setup VFs with reset, and
since we were going to inform Firmware about our intention to do VFLR by
disabling LAN TX Queue, then we really have to complete VF reset flow with
VFLR using appropriate registers - Otherwise, reset status bit for VF in
the Guest OS might returns DEADBEEF.
This resolves issue to properly initialize VFs in the Guest OS via PCI
passthrough.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
ice_get_guar_num_vsi currently calculates the number of VSIs per PF.
Rework this into a general function ice_get_num_per_func, that can
calculate per PF allocations for not just VSIs but across multiple
resource types.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
All VF VSIs need to be reset and rebuild with the main VSIs before
replaying all VSIs, so that all existing switch filters, scheduler tree
and other configuration could be replayed at once. This fixes issues when
doing PFR and CORER reset.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of hoping that our ITR granularity will be 2 usec program the
GLINT_CTL register to make sure the ITR granularity is always 2 usecs.
Now that we know what the ITR granularity will be get rid of the check
in ice_probe() to verify our previous assumption.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Replace all instances of:
for (i = 0; i < pf->num_alloc_vsi; i++)
with the following macro:
ice_for_each_vsi(pf, i)
This will allow the code to be consistent since there are currently
cases of using both.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In the ice_aq_set_phy_cfg AQ command, the 16.4 bit is reserved. This
patch will make sure that this bit will never be set to 1.
Signed-off-by: Chinh T Cao <chinh.t.cao@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_pf_rxq_wait we are using an unnecessary local variable and also
we are checking if the timeout time was reached after the loop. Get rid
of the local variable and return 0 right when we get a successful
result. This makes it so we can return -ETIMEDOUT if we ever exit the
loop because we know the timeout time has been hit.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add a local variable struct device *dev to avoid unnecessary de-references
throughout ice_probe().
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch fixes issues with VF queues being disabled, and VF netdev
network carrier being lost after reset. Basically, we need to check if VF
is enabled, and queue configured in reset_all_vfs flow, and disable/enable
those queues appropriately whenever the function is called after
Global/CORER/PFR reset/rebuild/replay.
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set egress (Rx) pruning enable flag for VF VSI in VSI ctxt to
enable prune action.
To avoid seeing broadcast packet in different VLAN, pruning enable
flag in VSI ctxt should be set.
Write new functions (fill VSI ctx) to not repeat send ctxt code.
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
A test started warning on a string truncation. This led to an unfortunate
realization that we are likely not accounting for the stats length
correctly before this patch, so fix the issue by putting "port." in front
of all the PF stats, instead of magically prepending it at runtime.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Ethtool reported pause params based on the currently negotiated
link settings instead of current PHY config. User was not able
to turn off pause params because ethtool was incorrectly reporting
parameters as off when link was down even though PHY was configured
to support pause frames. Now pause params are taken from PHY config
instead of link status.
Signed-off-by: Lukasz Czapnik <lukasz.czapnik@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When the PF driver sets up the VF MSI-X vector allocation, it needs to
use the hardware absolute vector ID, not the per-PF vector ID. Without
this change we see (apparent) TX hangs when using VFs on multiple PFs.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Check for a leaf node presence for a given VSI. This check is required
before removing a VSI since VSIs can't be removed with enabled queues
(with leaf nodes) from the FW scheduler tree unless its a reset.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Set the flush Tx pipe flag instead of getting an EAGAIN error when FW
times out in processing the disable Tx queue command.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
On older devices like X710 and X722, the VF's ARQLEN register is cleared
on reset, so the VF driver uses that register to detect an unannounced
reset. Unfortunately, on devices controlled by ice, this register is NOT
cleared on reset. This causes the VF to miss resets, and even on
properly-announced resets, the VF driver complains that it didn't see
the reset.
To fix this, we'll do it in software. When we handle a VF reset (whether
triggered by software or VFLR), clear this register after the HW reset
is complete.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Don't send a link message to the VFs unless link actually changes state.
This avoids a small timing hole in some VF drivers that can cause an
apparent TX hang if they receive a link status message at the wrong time.
Although we have fixed the timing hole in the current VF driver, there
are still lots of drivers in the field that have this timing hole. Let's
not fall into it if we can avoid it.
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
In ice_vsi_release we are always assigning a value to the local VF
variable. Change this to only be assigned if the VSI is a VF VSI.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When compiling and analyzing the driver on newer kernels, a static
analyzer warns about the following "numeric overflow" issues:
"The result of expression: 'budget-1' generates 4-byte type while casting
to a bigger size of 8-byte".
"The result of expression: '*words-words_read' generates 4-byte type
while casting to a bigger size of 8-byte".
Fix them both.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently if the kernel has the intel_iommu=on parameter set, on some
platforms removing the driver causes a system reboot. In initialization
we associate the control queue interrupts with the pf->hw_oicr_idx and
enable the interrupts by setting the CAUSE_ENA bit. The problem comes
on teardown because we are not clearing the CAUSE_ENA bit for the
control queues, but the vector at pf->hw_oicr_idx (miscellaneous
interrupt vector) gets disabled.
Fix this by clearing the CAUSE_ENA bit in the appropriate control queue
registers on when freeing the miscellaneous interrupt vector. Also,
move the call to ice_free_irq_msix_misc() to after ice_deinit_sw() in
ice_remove() because ice_deinit_sw() makes an AQ call, but
ice_free_irq_msix_misc() disables the miscellaneous vector and it's
associated interrupts.
Also, create two small helper functions to enable and disable the
control queue interrupts respectively.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When adding multiple VLANs to the same VSI, the ice_add_vlan code will
share the VSI list, so as not to create multiple unnecessary VSI lists.
Consider the following flow
ice_add_vlan(hw, <VSI 0 VID 7, VSI 0 VID 8, VSI 0 VID 9>)
Where we add three VLAN filters for VIDs 7, 8, and 9, all for VSI 0.
The ice_add_vlan will create a single vsi_list and share it among all
the filters.
Later, if we try to remove a VLAN,
ice_remove_vlan(hw, <VSI 0 VID 7>)
Then the removal code will update the vsi_list and remove VSI 0 from it.
But, since the vsi_list is shared, this breaks the list for the other
users who reference it. We actually even free the VSI list memory, and
may result in segmentation faults.
This is due to the way that VLAN rule share VSI lists with reference
counts, and is caused because we call ice_rem_update_vsi_list even when
the ref_cnt is greater than one.
To fix this, handle the case where ref_cnt is greater than one
separately. In this case, we need to remove the associated rule without
modifying the vsi_list, since it is currently being referenced by
another rule. Instead, we just need to decrement the VSI list ref_cnt.
The case for handling sharing of VSI lists with multiple VSIs is not
currently supported by this code. No such rules will be created today,
and this code will require changes if/when such code is added.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
struct ice_vsi_ctx has gotten large enough that function local declarations
of it on the stack are causing stack hogs. Fix that by allocating the
structs on heap. Cleanup some formatting issues in the code around these
changes and fix incorrect data type uses of returned functions in a couple
places.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
With sizeof(), it is preferable to use the variable of type <type> instead
of sizeof(<type>).
There are multiple places where a temporary variable is used to hold a
'size' value which is then used for a subsequent alloc/memset. Get rid
of the temporary variable by calculating size as part of the alloc/memset
statement.
Also remove unnecessary type-cast.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
VSI supported nodes are calculated in order to add the VSI parent or
intermediate nodes to the scheduler tree. If one of the node in below
layers (from VSI layer) has space to add the new VSI or intermediate node
above that layer then it's not required to continue the calculation further
for below layers.
Signed-off-by: Victor Raj <victor.raj@intel.com>
Reviewed-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently ICE_MAX_MTU subtracts only ETH_HLEN from max frame size and
adds ETH_FCS_LEN and VLAN_HLEN, which is not what was intended.
The ETH_HLEN + ETH_FCS_LEN + VLAN_HLEN expression should be surrounded
with parentheses.
Wrap mentioned expression and take into account VLAN double tagging.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Commit 87b0984ebf ("net: Add extack argument to ndo_fdb_add()") in
net-next added an extended parameter to the .ndo_fdb_add op and changed
ice_fdb_add() accordingly. Update the function header and add the
__always_unused attribute to the new parameter to avoid -Wunused-parameter
warnings.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Drivers may not be able to support certain FDB entries, and an error
code is insufficient to give clear hints as to the reasons of rejection.
In order to make it possible to communicate the rejection reason, extend
ndo_fdb_add() with an extack argument. Adapt the existing
implementations of ndo_fdb_add() to take the parameter (and ignore it).
Pass the extack parameter when invoking ndo_fdb_add() from rtnl_fdb_add().
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function ice_aq_manage_mac_write takes a pointer to a MAC address.
The parameter is not marked const, even though the function doesn't need
to modify it. This prevents passing a parameter that is already marked
const. Update the function prototype to take a const pointer, to allow
passing constant pointers to this function.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds code for the detection and operation of several
additional PHY types that support higher link speeds.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds the ability to offload SCTP checksum calculations to the
NIC.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use ethtool_op_get_ts_info to provide software timestamping.
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch includes the following ethtool operations:
1. get_coalesce
2. set_coalesce
3. get_per_q_coalesce
4. set_per_q_coalesce
Each ITR value (current_itr/target_itr) are stored on a per
ice_ring_container basis. This is because each valid ice_ring_container
can have 1 or more rings that are tied to the same q_vector ITR index.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Currently the driver does not support adaptive/dynamic interrupt
moderation. This patch adds support for this. Also, adaptive/dynamic
interrupt moderation is turned on by default upon driver load.
In order to support adaptive interrupt moderation, two functions were
added, ice_update_itr() and ice_itr_divisor(). These are used to
determine the current packet load and to determine a divisor based
on link speed respectively.
This patch also adds the ICE_ITR_GRAN_S define that is used in the
hot-path when setting a new ITR value. The shift is used to pet two
birds with one hand, set the ITR value while re-enabling the
interrupt. Also, the ICE_ITR_GRAN_S is defined as 1 because the device
has a ITR granularity of 2usecs.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The aggregator list needs to be preserved for use after a reset. This
patch moves it out of the port_info instance and into the ice_hw instance.
Signed-off-by: Tarun Singh <tarun.k.singh@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch reworks the queue management code to allow for reuse with the
XDP feature (to be added in a future patch).
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add new infrastructure for implementing ethtool private flags using the
existing pf->flags bitmap to store them, and add the link-down-on-close
ethtool private flag to optionally bring down the PHY link when the
interface is administratively downed.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
When a netdev is set up/down we need to set the phsyical link state
accordingly. This patch adds that functionality by calling
ice_force_phys_link_state(vsi, link_up) in both the ice_stop() and
ice_open() paths.
In order to force link, ice_force_phys_link_state(vsi, link_up) will
first determine the current phy capabilities. If link has not changed
there is nothing to do. If link has changed, previous PHY capabilities
are saved and the "Enable Automatic Link Update" and "Link Establishment
State Machine (LESM)" enable bits are set. Then the new PHY config is
saved. The "Enable Automatic Link Update" will force the FW to execute
Setup link and restart auto-negotiation. This *should* then result in a
"Link Status Event (LSE)" which will cause the driver to get the current
link status.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
