Add UHB (ultra high band) channels and use 16 bit variables
to fit the new channels.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If number of channels in the driver is greater than
number of scan channels given by firmware TLV, do not
fail scan config, but adjust to firmware's number of channels.
This is helpful for supporting in driver new channels before
it being supported by firmware scan.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For some reason we never enabled it, but it appears to work fine.
Enable it now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Set the capabilities flags and inform firmware
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There are some buggy APs that keeps changing the count while forcing
us to block TX. This eventually results in queue hang, assert, and
disconnection. Detect such APs and disconnect gracefully in advance.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we receive channel switch announcement with immediate
quiet and unknown switching time, we will switch when FW identifies
AP left channel. However, if AP remains on channel, we will
eventually get TX queue hang. Init a work to disconnect if
switch doesn't occur within 1500 milliseconds. Do it also
for a too long channel switch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Let FW know if quiet mode is on or not. This is needed
in order to disable it in FW when CSA is complete.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Send to FW modify command for every beacon we receive during channel
switch. FW will track the count, and make sure the event is scheduled
in time even if AP changed count.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Report all NO_DATA events to mac80211 so they get captured
in radiotap for usage in sniffer scenarios; map the info
type to a reasonable radiotap type for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case we receive abort operation for CSA, clean up
our state.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support passing to FW delayed beacon count. This
represents the delay the AP can have when moving to
the new channel.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
rename few structs to fit the new marketing names
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of alive interrupt timeout or any failure in the init flow
the driver generates FW nmi. The driver assumes that the nmi will
generate SW interrupt. This assumption does not hold and leads to faulty
behavior in the recovery flow.
Solve this by using sync nmi, this way, even if the driver does not
receive SW interrupt, it still starts the recovery flow.
Also remove the wait queue from iwl_fwrt_stop_device since the driver is
handling the SW interrupt synchronously.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The driver initiates the size value with the size of the struct and then
adds the size of the data and checks if the size is zero so size can not
be equal to zero.
Solve this by getting the data size, check that it is not equal to zero
and only then add the struct size.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Fixes: 7a14c23dcd ("iwlwifi: dbg: dump data according to the new ini TLVs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case the driver fails to dump a memory region, and this is the last
region, then partial region would be extracted.
Solve this by setting the data to zero in case of failure.
This will cause dump to be a list of consecutive successful memory
regions and trailing zeros with no partial memories extracted.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Allow modules from outside pcie to call sync_nmi.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the old days, we could transmit with HW crypto with an arbitrary
key by filling it into TX_CMD. This was broken first with the advent
of CCMP/GCMP-256 keys which don't fit there.
This was broken *again* with the newer TX_CMD format on 22560+,
where we simply cannot pass key material anymore. However, we forgot
to update all the cases when we get a key from mac80211 and don't
program it into the hardware but still return 0 for HW crypto on TX.
In AP mode with WEP, we tried to fix this by programming the keys
separately for each station later, but this ultimately turns out to
be buggy, for example now it leaks memory when we have more than one
WEP key.
Fix this by simply using only SW crypto for WEP in newer devices by
returning -EOPNOTSUPP instead of trying to program WEP keys later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
After the previous patch, all the callers of ndo_select_queue()
provide as a 'fallback' argument netdev_pick_tx.
The only exceptions are nested calls to ndo_select_queue(),
which pass down the 'fallback' available in the current scope
- still netdev_pick_tx.
We can drop such argument and replace fallback() invocation with
netdev_pick_tx(). This avoids an indirect call per xmit packet
in some scenarios (TCP syn, UDP unconnected, XDP generic, pktgen)
with device drivers implementing such ndo. It also clean the code
a bit.
Tested with ixgbe and CONFIG_FCOE=m
With pktgen using queue xmit:
threads vanilla patched
(kpps) (kpps)
1 2334 2428
2 4166 4278
4 7895 8100
v1 -> v2:
- rebased after helper's name change
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My commit 26a7b54731 ("mt76x02: set protection according to ht
operation element") enabled by default RTS/CTS protection for OFDM
and CCK traffic, because MT_TX_RTS_CFG_THRESH is configured to non
0xffff by initvals and .set_rts_threshold callback is not called by
mac80211 on initialization, only on user request or during
ieee80211_reconfig() (suspend/resuem or restart_hw).
Enabling RTS/CTS cause some problems when sending probe request
frames by hcxdumptool penetration tool, but I expect it can cause
other issues on different scenarios.
Restore previous setting of RTS/CTS being disabled by default for
OFDM/CCK by changing MT_TX_RTS_CFG_THRESH initvals to 0xffff.
Fixes: 26a7b54731 ("mt76x02: set protection according to ht operation element")
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
__sw_hweight8() is only defined if CONFIG_GENERIC_HWEIGHT is enabled.
The function that works on all architectures is hweight8().
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since some USB device IDs are duplicated between mt76x0u, mt7601u
and mt76x2u device, check chip version on probe and return error if
not match the driver.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not our device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since some USB device IDs are duplicated between mt7601u and mt76x0u
devices, check chip version on probe and return error if not match
0x7601.
Don't think this is serious issue, probe most likely will fail at
some other point for wrong device, but we do not have to configure
it if we know is not mt7601u device.
Reported-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
do_div() expects unsigned operands and otherwise triggers a warning like:
drivers/net/wireless/intel/iwlwifi/mvm/ftm-initiator.c:465:2: error: comparison of distinct pointer types ('typeof ((rtt_avg)) *' (aka 'long long *') and 'uint64_t *' (aka 'unsigned long long *')) [-Werror,-Wcompare-distinct-pointer-types]
do_div(rtt_avg, 6666);
^~~~~~~~~~~~~~~~~~~~~
include/asm-generic/div64.h:222:28: note: expanded from macro 'do_div'
(void)(((typeof((n)) *)0) == ((uint64_t *)0)); \
~~~~~~~~~~~~~~~~~~ ^ ~~~~~~~~~~~~~~~
1 error generated.
Change the do_div() to the simpler div_s64() that can handle
negative inputs correctly.
Fixes: 937b10c0de ("iwlwifi: mvm: add debug prints for FTM")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Remove duplicated entry in mt76x2u_device_table since Alfa AWUS036ACM
and Aukey USB-AC1200 have the same ids
Fixes: 62a25dc569 ("mt76x2u: Add support for Alfa AWUS036ACM")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
This feature has been reported to cause stability issues on several systems.
Disable it until it has been fixed and verified. It can still be enabled
through debugfs
Signed-off-by: Felix Fietkau <nbd@nbd.name>
These packets have no txwi entry in the ring, so tracking via tx status does
not work. To prevent PS poll requests from being unanswered, end the service
period right away
Signed-off-by: Felix Fietkau <nbd@nbd.name>
AGC register 35, 37 override for the low gain setting should only be done
on 5 GHz. Also, 2.4 GHz needs a different value for register 35
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Use the correct variable in the check. Fixes an uninitialized variable warning
Reported-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Fixes: c8846e1015 ("mt76: add driver for MT7603E and MT7628/7688")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Full tx blocking (as opposed to CCA blocking) should only happen if there
is a continuous non-802.11 signal above the energy detect threshold.
Unfortunately the ED/CCA counter can't detect that, as it also counts 802.11
signals as busy.
Similar to the vendor code, implement a learning mode that waits until the AGC
gain has already been adjusted to the lowest value (due to false CCA events),
and the number of false CCA events still remains high, and the blocking
threshold is exceeded for more than 5 seconds.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Also update the mask first before calculating the vif index.
Fixes an issue where adding back the same interfaces in a different order
fails because of duplicate vif index use
Fixes: 06662264ce ("mt76x02: use mask for vifs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Since we add txwi at the begining of skb->data, it no longer point
to ieee80211_hdr. This breaks settings TS bit for probe response and
beacons.
Acked-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Introduce mt76_queue stopped parameter in order to run
ieee80211_wake_queue only when mac80211 queues have been
previously stopped and avoid to disable interrupts when
it is not necessary
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
ies1 or ies2 might be null when code inside
_wil_cfg80211_merge_extra_ies access them.
Add explicit check for null and make sure ies1/ies2 are not
accessed in such a case.
spos might be null and be accessed inside
_wil_cfg80211_merge_extra_ies.
Add explicit check for null in the while condition statement
and make sure spos is not accessed in such a case.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HALP ICR is set as long as the FW should stay awake.
To prevent its multiple handling the driver masks this IRQ bit.
However, if there is a different MISC ICR before the driver clears
this bit, there is a risk of race condition between HALP mask and
unmask. This race leads to HALP timeout, in case it is mistakenly
masked.
Add an atomic flag to indicate if HALP ICR should be handled.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Upon status ring handling, in case there are both unicast and
multicast (cid == max) status messages to handle, wrong sta statistics
might get updated.
Fix this by setting stats to NULL upon invalid cid
(e.g. == max_assoc_sta).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rearrange the code by having functions to access 802.3 header
members, source and destination addresses.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
New FW added support for upto 20 clients in AP mode. Change the driver
to support this as well. FW reports it's max supported associations in
WMI_READY_EVENT. Some WMI commands/events use cidxtid field which is
limited to 16 cids. Use new cid/tid fields instead.
For Rx packets cid from rx descriptor is limited to 3 bits (0..7),
to find the real cid, compare transmitter address with the stored
stations mac address in the driver sta array.
EDMA FW still supports 8 stations. Extending the support to 20
stations will come later.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
