When firmware crashes it's possible to create a coredump for later analysis,
add support to collect the register and memory info from SDIO devices.
The coredump configuration is different between QCA6174 PCI and QCA6174 SDIO,
so add specific registers and memory regions for the latter.
QCA6174 SDIO has two methods to dump the firmware: fastdump and slowdump.
Fastdump is not supported in olded versions of firmware, and for these ath10k
will automatically select slowdump. If firmware supports fastdump, ath10k will
automatically select it. QCA6174 SDIO firmware version
WLAN.RMH.4.4.1-00017-QCARMSWPZ-2 is the first version supporting fastdump.
For slowdump, ath10k_sdio_hif_diag_read() can not be used as the diag
window has a limit value, it is 4 bytes and the dump's buffer length is larger
than it, it will trigger error. So this patch adds ath10k_sdio_read_mem() to
read 4 bytes for each time.
Example output of a firmware crash:
ath10k_sdio mmc1:0001:1: simulating soft firmware crash
ath10k_sdio mmc1:0001:1: firmware crashed! (guid 413d98b1-84c0-4298-b605-2b10ec0c54a5)
ath10k_sdio mmc1:0001:1: qca6174 hw3.2 sdio target 0x05030000 chip_id 0x00000000 sub 0000:0000
ath10k_sdio mmc1:0001:1: kconfig debug 1 debugfs 1 tracing 1 dfs 0 testmode 1
ath10k_sdio mmc1:0001:1: firmware ver WLAN.RMH4.4.1-00126-QCARMSWP-1 api 6 features wowlan,ignore-otp,raw-mode crc32 b84317cf
ath10k_sdio mmc1:0001:1: board_file api 2 bmi_id 0:4 crc32 6364cfcc
ath10k_sdio mmc1:0001:1: htt-ver 3.69 wmi-op 4 htt-op 3 cal otp max-sta 32 raw 0 hwcrypto 1
ath10k_sdio mmc1:0001:1: firmware register dump:
ath10k_sdio mmc1:0001:1: [00]: 0x05030000 0x000015B3 0x0099908D 0x00955B31
ath10k_sdio mmc1:0001:1: [04]: 0x0099908D 0x00060730 0x00000018 0x004641A0
ath10k_sdio mmc1:0001:1: [08]: 0x0041FAA4 0x0041FA9C 0x00999070 0x00404490
ath10k_sdio mmc1:0001:1: [12]: 0x00000009 0xFFFFFFFF 0x00952CD0 0x00952CE6
ath10k_sdio mmc1:0001:1: [16]: 0x00952CC4 0x00910712 0x00000000 0x00000000
ath10k_sdio mmc1:0001:1: [20]: 0x4099908D 0x0040E9E8 0x00000001 0x00423AC0
ath10k_sdio mmc1:0001:1: [24]: 0x809F3189 0x0040EA48 0x00426240 0xC099908D
ath10k_sdio mmc1:0001:1: [28]: 0x809143A7 0x0040EA68 0x0041FAA4 0x00423A80
ath10k_sdio mmc1:0001:1: [32]: 0x809F1193 0x0040EA88 0x00411770 0x004117E0
ath10k_sdio mmc1:0001:1: [36]: 0x809F0EEE 0x0040EAA8 0x00000000 0x00000000
ath10k_sdio mmc1:0001:1: [40]: 0x80911210 0x0040EAC8 0x00000008 0x00404130
ath10k_sdio mmc1:0001:1: [44]: 0x80911154 0x0040EB28 0x00400000 0x00000000
ath10k_sdio mmc1:0001:1: [48]: 0x8091122D 0x0040EB48 0x00000000 0x00400600
ath10k_sdio mmc1:0001:1: [52]: 0x40910024 0x0040EB78 0x0040AB98 0x0040AB98
ath10k_sdio mmc1:0001:1: [56]: 0x00000000 0x0040EB98 0x009BB001 0x00040020
Tested-on: QCA6174 SDIO WLAN.RMH.4.4.1-00018-QCARMSWP-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1569310030-834-3-git-send-email-wgong@codeaurora.org
There's no reason to have call for enable_pll_clk in ath10k_bmi_start(), move
it to ath10k_core_start() instead. This way it's possible to call
ath10k_bmi_start() from sdio.c during firmware dump creation. And also the
function call is more visible when it's in core.c.
No functional changes, compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/1597421745-4329-1-git-send-email-kvalo@codeaurora.org
'cmd' is malloced in ath10k_bmi_lz_data_large() and should be freed
before leaving from the error handling cases, otherwise it will cause
memory leak.
Fixes: d58f466a5d ("ath10k: add large size for BMI download data for SDIO")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200427104348.13570-1-weiyongjun1@huawei.com
Download firmware time cost of SDIO is too long, it is about 480ms,
add large size 2048 bytes for BMI download for SDIO chip, its time
cost will reduced to 240ms.
This will optimize the download firmware time cost.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Downloading firmware via BMI protocol takes too long time. For example,
a ~700K bytes firmware takes about 500ms to download via BMI protocol.
This is too long especially in suspend and resume scenario where firmware
is re-downloaded unless WoWLAN is enabled. Downloading firmware via diag CE
can reduce the time to ~40ms for a ~700K bytes firmware binary.
Ath10k driver parses the firmware to segments and downloads the segments
to the specified address directly. If the firmware is compressed or has
unsupported segments, ath10k driver will try BMI download again.
It's tested with QCA6174 hw3.2 and
firmware-6.bin_WLAN.RM.4.4.1-00111-QCARMSWP-1. QCA9377 is also affected.
Signed-off-by: Carl Huang <cjhuang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Special BMI get target info function for SDIO.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Len Brown reported the system resume time is taking more than 2 seconds in
bug - https://bugzilla.kernel.org/show_bug.cgi?id=185621.
The reason of the 2 seconds is due to the firmware download time.
The chip is booted up in the default reference clock speed to handle the
firmware download to chip memory and advanced to the support higher speed
clock to run the firmware after all. The default reference clock in the
hardware is slow so that the firmware download time is taking up to 2
seconds for a 600KB firmware file.
[76796.349701] ath10k_pci : boot uploading firmware image len 688691
[76798.334612] ath10k_pci : htt tx max num pending tx 1056
The resolution here is to enable the higher speed clock if the hardware
supported before the firmware download at BMI stage, so that the hardware
can handle the firmare download in a more efficient way. This can help to
improve the firmware download time from 2 seconds to around 500ms for the
same 600KB firmware file.
[322858.577919] ath10k_pci boot uploading firmware image len 688691
[322859.093094] ath10k_pci htt tx max num pending tx 1056
The steps to advance to the higher speed clock is very hardware specific,
so adding the hardware ops for the hardware that can support this.
Reported-by: Len Brown <lenb@kernel.org>
Tested-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Ryan Hsu <ryanhsu@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
With the %pK format specifier we hide the kernel addresses
with the help of kptr_restrict sysctl.
In this patch, %p is changed to %pK in the driver code.
The sysctl is documented in Documentation/sysctl/kernel.txt.
Signed-off-by: Maharaja Kennadyrajan <c_mkenna@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This makes it a lot easier to log and debug
messages if there's more than 1 ath10k device on a
system.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
It's just cleaner to have separate argument for the parameter and result. Also
fix returned error value if response length is invalid.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is necessary if we want to be able to restart
hw on-the-fly.
Signed-off-by: Michal Kazior <michal.kazior@tieto.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Here's a new mac80211 driver for Qualcomm Atheros 802.11ac QCA98xx devices.
A major difference from ath9k is that there's now a firmware and
that's why we had to implement a new driver.
The wiki page for the driver is:
http://wireless.kernel.org/en/users/Drivers/ath10k
The driver has had many authors, they are listed here alphabetically:
Bartosz Markowski <bartosz.markowski@tieto.com>
Janusz Dziedzic <janusz.dziedzic@tieto.com>
Kalle Valo <kvalo@qca.qualcomm.com>
Marek Kwaczynski <marek.kwaczynski@tieto.com>
Marek Puzyniak <marek.puzyniak@tieto.com>
Michal Kazior <michal.kazior@tieto.com>
Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
