The firmware can now request SMPS (due to thermal conditions), add
some code to honour such requests and bubble them up through the
stack, subject to our other SMPS constraints, e.g. from Bluetooth.
Then, if the firmware requests SMPS, then we know that it supports
a small extension to the PHY configuration API where a chain mask
of 0 means "use 1 but pick which one yourself", so in this case we
use that extension.
During firmware restart, we stay in the previous state, and the FW
will send us a notification at startup (only) if the temperature is
below the lower or above the high threshold, to sync the state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.85656b7684b9.I7a661a0758d070a750d3a91874d1a0f5fab9febc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If there are frequent CCA delays due to the extension channel
as detected by the firmware, and we're on 2.4 GHz, then handle
this by disconnecting (with a reconnect hint).
When we disconnect, we'll also update our capabilities to use
only 20 MHz on the next connection (if it's on 2.4 GHz) as to
avoid the use of the extension channel that has too much noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4de9c363b0b5.I709b7e6f73a7537c53f22d7418927691259de8a8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Implement CSI (channel estimation matrix) reporting in the mvm
driver, if the firmware has the capability.
Currently only a debugfs API is provided as the API is still
under discussion.
For now, RX aggregation must be disabled to use this feature
on data frames as we haven't found a good way to attach the
data to A-MPDUs, given complexities with multi-queue.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Handle RX no data notification, which is used for advertising NDP to
radiotap.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In order to receive TB (Trigger Based) PPDU in monitor mode,
the Driver must send the HE_AIR_SNIFFER_CONFIG_CMD host command.
Enable that via debugfs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently multi-queue is disabled for 22000 devices.
This was since driver isn't supposed to write to prph
registers anymore, and FW needs to configure the RFH.
Now that FW added support for the API - use it and remove
the 22000 multi RX queue disablement.
Bump min API version to avoid compatibility issues.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update rs-fw API to match changes in FW. Specifically, the
TLC_MNG_NOTIF_REQ_CMD command and TLC_MNG_AMSDU_ENABLE_NOTIF
notification are removed, the A-MSDU related info is received from FW
via the TLC_MNG_UPDATE_NOTIF, and the TLC_MNG_CONFIG_CMD uses version
2 of its data structure.
Additionally, constify some arguments in a couple of functions.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support the new APIs and activate AMSDU based on the
offloaded TLC decisions.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch sends to the FW notification configuration command and
handles the update responses.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This patch adds rate scaling configuration command and
implements a few other handlers.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Apart from DVM, all firmware uses the same base API, and there's
code outside iwlmvm that needs to interact with it. Reflect this
in the source better and reorganize the firmware API to a new
fw/api/ directory.
While at it, split the already pretty large fw-api.h file into a
number of smaller files, going from almost 3k lines in there to
a maximum number of lines less than 1k.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
