During D3 state, FW may send packets.
As a result, "write" queue pointer will be incremented by FW.
Upon resume from D3, driver should adjust its shadows of "write" and "read"
pointers to the value reported by FW.
1. Keep TID used during wowlan configuration.
2. Upon resume, set driver's "write" and "read" queue pointers
to the value reported by FW.
Signed-off-by: Alex Malamud <alex.malamud@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Now that d0i3 is dead, this function can't be called from d0i3
flows. Change its signature and make it static.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support the new DBGC_SUSPEND_RESUME command to change the recording state.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The 0xF6 command used to start and stop the recording from 22560 devices
was removed. This is causing an assert when the driver tries to alter
the recording state.
Remove the use of the command.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
From 9000 device family the FW automatically stops the debug
recording and the driver should not stop it as well.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Unite iwl_trans debug related fields under iwl_trans_debug struct to
increase readability and keep iwl_trans clean.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*pattern_cmd) +
wowlan->n_patterns * sizeof(struct iwlagn_wowlan_pattern)
to :
struct_size(pattern_cmd, patterns, wowlan->n_patterns)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This debugfs file is really old, and cannot work properly since
the unified image support. Rather than trying to make it work,
which is difficult now due to multiple images (LMAC/UMAC etc.)
just remove it - we no longer need it since we properly do a FW
coredump even in D3 cases.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add new definitions for the WoWLAN patterns API version 2 and support
for version 2 of the WoWLAN patterns command without implementing the
new features. With this commit we only supporting the existing
bitmask pattern match. Use the new version only if the TLV is set.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In restart flow, the driver requests HW restart from mac80211
and then mac80211 uses a worker to do the restart flow. In that flow a
sync dump is performed. Instead, schedule the dump worker before
requesting HW restart from mac80211. This approach simplifies the
restart flow.
Also, it is neeeded in order to differentiate between the handling of SW
and HW errors in a future commit.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Newer FWs use a new format of the SCAN_OFFLOAD_PROFILES_QUERY_RSP,
which now supports indicating match on an higher number of channels.
Modify the code to support both the old format and the newer one,
based on a FW TLV.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TLV 54 holds umac debug related addresses.
TLV 55 holds lmac debug related addresses.
These TLVs aim to replace the alive notification data in the future.
Parse and keep error table addresses received from the TLVs
for both lmac and umac and use these addresses instead of the pointer
received from alive notification.
The feature supports only unified image.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move to use the new mac80211 TXQs implementation. This has
quite a few benefits for us. We can get rid of the awkward
mapping of DQA to mac80211 queues. We can stop buffering
traffic while waiting for the queue to be allocated. We can
also use mac80211 AMSDUs instead of building it ourselves.
The usage is pretty simple:
Each ieee80211_txq contains iwl_mvm_txq. There is such a
queue for each TID, and one for management frames. We keep
having static AP queues for probes and non-bufferable MMPDUs,
along with broadcast and multicast queues. Those are being
used from the "old" TX invocation path - iwl_mvm_mac_tx.
When there is a new frame in a TXQ, iwl_mvm_mac_wake_tx is
being called, and either invokes the TX path, or allocates
the queue if it does not exist.
Most of the TX path is left untouched, although we can consider
cleaning it up some more, for example get rid of the duplication
of txq_id in both iwl_mvm_txq and iwl_mvm_dqa_txq_info.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
void *entry[];
};
instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The trigger structure is being passed around, when
all we care about is whether to dump only monitor
or not. Pass a bool instead.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the rt status checking to the start of the resume flow in order
to avoid sending D0I3_END_CMD to the FW. Also, collect dump if an
assert was encountered.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed. Note that RSC is sent separately in
a new command. This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
CDB support has nothing to do with non unified image.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Make all FW debug data stop recording flows to use
iwl_fw_dbg_stop_recording function instead of writing to FW
registers directly.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A new FW API has been added for WOWLAN_GET_STATUSES to support
multiple GTK keys and IGTK keys. Check the respective TLV and use the
new API when it is set.
Let most of the code use the new version (v7) and convert the old
version (v6) to the new one when needed.
Also refactor some functions a bit so that they can be reused more
easily. Particularly the part that calls WOWLAN_GET_STATUSES which is
reused in D3 and D0i3.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We repeated the same if twice in a row. Remove the second one and
move the code block into the previous one.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During d3, the firmware records debug data into internal buffer
if debug data collection occurs, collect the data that was written to the
buffer
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently the firmware does not stop recording debugging data when
entering D3 and this causes trouble (e.g. sporadic wake ups).
Fix that by stopping dbg recording when suspending.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In case of "any" wowlan trigger is configured, no valid wakeup filter
was configured.
Moreover, the fw assumes there's no connection when there are no configured
wakeup filters.
This leads to the station info not being updated on D3 command, causing
rate_n_flags to be 0 when the offloading code sends tx frame (triggering
SYSASSERT_102C due to invalid antenna param)
Note: "any" trigger is currently assumed to only be used when entering
d0i3 (which has a different flow). However, we still reach this code
when using d3_test.
Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Traffic condition monitor gathers data about the traffic load and
other conditions and can be used to make decisions regarding latency,
throughput etc. This patch introduces the code and data structures to
collect this data for future use.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
While entering to D3 mode there is a gap between the time the
driver handles the D3_CONFIG_CMD response to the time the host is going
to sleep.
In between there might be cases which MARKER_CMD can tailgate.
Also during resume flow the MARKER_CMD might get sent while D0I3_CMD
is being handled in the FW.
Cancel MARKER_CMD timer and set it again properly during suspend
resume flows to prevent this command from being sent accidentlly.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This feature was actually removed from firmware, but without
ever telling the driver. Since nobody is actually using it,
just remove it entirely without bothering with a capability
check.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
New quota command adds a field indicating low latency
direction per quota.
A TLV API bit was added to indicate the new API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If we set disconnect on wowlan and run suspend/resume, will run
into:
...snipped
iwlwifi 0000:01:00.0: Failed to load firmware chunk!
iwlwifi 0000:01:00.0: Could not load the [0] uCode section
iwlwifi 0000:01:00.0: Failed to start INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to run INIT ucode: -110
iwlwifi 0000:01:00.0: Failed to start RT ucode: -110
It is because we still keep IWL_MVM_STATUS_IN_HW_RESTART in
__iwl_mvm_resume. When mac80211 starts the device as
__iwl_mvm_mac_start(), we will miss iwl_mvm_restart_cleanup(mvm).
Signed-off-by: Matt Chen <matt.chen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Where possible (all except for "11n_disable", which isn't valid in C)
rename the internal names for module parameters to be the same as the
externally visible names, to aid finding their use etc.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
-----BEGIN PGP SIGNATURE-----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=DdqX
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-06-28' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
More iwlwifi patches for 4.13
* Some changes in suspend/resume handling to support new FWs;
* A bunch of RF-kill related fixes;
* Continued work towards the A000 family;
* Support for a new version of the TX flush FW API;
* Some fixes in monitor interfaces;
* A few fixes in the recovery flows;
* Johannes' documentation fixes and FW API struct cleanups continue;
* Remove some noise from the kernel logs;
* Some other small improvements, fixes and cleanups;
New FW versions require the D0I3_END_CMD to be sent as the first
command to the FW in the resume flow. If the TLV is set, send that
command first, otherwise keep the original behavior (i.e. send last).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is no need to send D0I3_END_CMD as ASYNC during the system
resume flow. Additionally, the other flags used are meaningless in
this case (they were just copied from the runtime resume flow), so
remove them all.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Contrary to what some of the comments say, if rfkill was
asserted the transport will return -ERFKILL instead of
success, if CMD_WANT_SKB was set, so it's not necessary
to check cmd.resp_pkt for being NULL if the return code
was success.
Validate that this is true in iwl_trans_send_cmd().
Most of the other code modifications were done with the
following spatch:
@@
struct iwl_host_cmd cmd;
identifier pkt;
@@
<...
(
pkt = cmd.resp_pkt;
...
-if (!pkt) { ... }
|
pkt = cmd.resp_pkt;
...
-if (WARN_ON(!pkt)) { ... }
|
-if (!cmd.resp_pkt) { ... }
)
...>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A common pattern with skb_put() is to just want to memcpy()
some data into the new space, introduce skb_put_data() for
this.
An spatch similar to the one for skb_put_zero() converts many
of the places using it:
@@
identifier p, p2;
expression len, skb, data;
type t, t2;
@@
(
-p = skb_put(skb, len);
+p = skb_put_data(skb, data, len);
|
-p = (t)skb_put(skb, len);
+p = skb_put_data(skb, data, len);
)
(
p2 = (t2)p;
-memcpy(p2, data, len);
|
-memcpy(p, data, len);
)
@@
type t, t2;
identifier p, p2;
expression skb, data;
@@
t *p;
...
(
-p = skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
|
-p = (t *)skb_put(skb, sizeof(t));
+p = skb_put_data(skb, data, sizeof(t));
)
(
p2 = (t2)p;
-memcpy(p2, data, sizeof(*p));
|
-memcpy(p, data, sizeof(*p));
)
@@
expression skb, len, data;
@@
-memcpy(skb_put(skb, len), data, len);
+skb_put_data(skb, data, len);
(again, manually post-processed to retain some comments)
Reviewed-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For dynamic SAR, we will need to select the current profile from
different places. In preparation for that, spin the profile selection
code out of iwl_mvm_sar_init().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In a000 devices we will support up to 32 stations.
The max station define is used also for invalid station marking
which makes finding usages of actual maximum station pretty hard
to sort through - change it to be a different define in order
to make future changes easier.
Use also ARRAY_SIZE intead of define when possible.
Do not move yet to 32 stations until firmware do it though.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The command was changed to support PN offload and TKIP offload.
The FW will do TKIP calculations in D0 only for a000 devices,
but API is aligned anyway.
However, for all devices we can stop sending the wowlan tkip
command.
Firmware will fetch the keys from the station key command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For a000 devices the binding API needs to include relevant
lmac ID - support the new API.
The new API should be used regardless if the device had CDB or
not. If there is no actual CDB support the binding is bound
to first lmac regardless of the band.
There are some functionality changes in binding restrictions
and quota allocations that will be handled in future patches.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a long-standing bug that was introduced when this code
was introduced: cfg80211 passes a pointer, but we treat it as if
it was passing a value. The result is that we pass the pointer to
the firmware, instead of the value. It's not clear how this could
ever have worked, unless the firmware is ignoring this value.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support getting alive from two LMACs and dumping debug
data from both.
Deprecate older alive notifications no one is using.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For unified images, we shouldn't restart the HW if suspend fails. The
only reason for restarting the HW with non-unified images is to go
back to the D0 image.
Fixes: 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With unified images, we need to make sure the net-detect scan is
stopped after resuming, since we don't restart the FW. Also, we need
to make sure we check if there are enough scan slots available to run
it, as we do with other scans.
Fixes: commit 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the suspend flow fails, we restart the hardware to go back to
the D0 image (with non-unified images), but we don't comply with
the fw_restart module parameter. If something goes wrong when
starting the D3 image, we may want to debug it, so we should
comply with the fw_restart flag to avoid clearing everything up
and losing the firmware state when the error occurred.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When a unified D0/D3 image is used, we don't restart the FW in the
D0->D3->D0 transitions. Therefore, the d3_test functionality should
not call ieee8021_restart_hw() when the resuming either.
Fixes: commit 23ae61282b ("iwlwifi: mvm: Do not switch to D3 image on suspend")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
