We used to read the PPAG, WRDS, EWRD, WGDS tables from ACPI
in the load stage only. This prevented vendor commands from
being executed before bringing the interface up. Move reading those tables
to INIT stage.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210805141826.ce3b60f0b426.I3643bf00e714aae930880cc7d6cf390b142eaccb@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Conceptually, this belongs more into the firmware utils
rather than the mvm opmode, so move the collection and
output there.
Note that this slightly changes the format of the Status
line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210621103449.b82b60d81346.Ide3b688107f6a59c7fc7eb1d8f2002b0a5c1f2d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The firmware can now request SMPS (due to thermal conditions), add
some code to honour such requests and bubble them up through the
stack, subject to our other SMPS constraints, e.g. from Bluetooth.
Then, if the firmware requests SMPS, then we know that it supports
a small extension to the PHY configuration API where a chain mask
of 0 means "use 1 but pick which one yourself", so in this case we
use that extension.
During firmware restart, we stay in the previous state, and the FW
will send us a notification at startup (only) if the temperature is
below the lower or above the high threshold, to sync the state.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.85656b7684b9.I7a661a0758d070a750d3a91874d1a0f5fab9febc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
SMPS requests may differ per interfaces due to e.g. Bluetooth
only interfering on 2.4 GHz, so if that's the case we should,
in the case of multiple PHY contexts, still allow RX diversity
on PHY context that have no interfaces with SMPS requests.
Fix the code to pass through the PHY context in question and
skip interfaces with non-matching PHY context while iterating.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.123c6b05809d.I992e3d1c6a29850d02eeec01712b5b685b963a87@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When doing scan while 6GHz channels are not enabled, the 6GHz band
is not scanned. Thus, if there are no APs on the 2GHz and 5GHz bands
(that will allow discovery of geographic location etc. that would
allow enabling the 6GHz channels) but there are non collocated APs
on 6GHz PSC channels these would never be discovered.
To overcome this, FW added support for performing passive UHB scan
in case no APs were discovered during scan on the 2GHz and 5GHz
channels.
Add support for enabling such scan when the following conditions are
met:
- 6GHz channels are supported but not enabled by regulatory.
- Station interface is not associated or less than a defined time
interval passed from the last resume or HW reset flows.
- At least 4 channels are included in the scan request
- The scan request includes the widlcard SSID.
- At least 50 minutes passed from the last 6GHz passive scan.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.7c7bd00e0aeb.Ib226ad57e416b43a710c36a78a617d4243458b99@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we do queue sync, it's confusing that we have the structures
declared in the FW API header files that aren't really firmware,
and the union is also confusing - especially now in the code that
checks the size on the return.
So rework this: change the type of sync and whether to do it in a
synchronous fashion to arguments, and build the data structure in
the function, so we don't need the union.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210331121101.f62833fd9893.I612d7ac1c655ec4880329360e15d207698c750bc@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
No need to pass the dbgfs_dir just to assign it to mvm.
Assign to mvm and then call iwl_mvm_dbgfs_register.
This is a preparation towards the addition of a delayed
op_mode_start flow.
This will allow to split the op_mode_start flow.
Registration to debugfs must happen after we register to
mac80211 and the registration to mac80211 will soon be
delayed in certain cases. In order not to have to remember
the debugfs_dir in a separate variable, just set it into
the mvm structure so that it can be usable later.
Declare mvm->debugfs_dir in the iwl_mvm structure even when
IWLWIFI_DEBUGFS isn't enabled to simplify the source code.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.a92ee491863d.I047923aa3598fbf4fb6fce2cdff75a4969fedd76@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
RF Interference Mitigation is a new feature targeted to handle the
problem of interference between DDR memory and WiFi. The role of
the driver is to configure FW with the table holding a mapping
between problematic channels/bands and the corresponding frequencies.
This patch adds RFI infrastructure and adds two debugfs hooks:
- send RFI configuration command (currently with a default table) which
will reset feature in the FW
- read the table, used by the FW (which can be a subset of the table
that driver sent).
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.2cea55a09bc7.I634b79795abad499ce442631d6672ffef8fc6d41@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If the firmware has support, then advertise it to the stack and
send the key down. Since we re-check the protection in the host
anyway, we don't really need to do anything on RX except that we
should drop frames that the firmware _knows_ are replay errors,
since beacon filtering might otherwise result in replays being
possible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210205110447.f5a3d53301b3.I23e84c9bb0b039d9106a07e9d6847776757f9029@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In the new api all the flush in the FW is done before we
get the response and in the response we only get the updated
read pointer and all queued packets don't get anymore rx_tx
per packet to free the queued packet, so driver needs to free
all queued packets on flushed queue at once after flush response.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4bd0eca8c0ef.I1601aad2eb2cc83f6f73b8ca52be57bb9fd626ab@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If there are frequent CCA delays due to the extension channel
as detected by the firmware, and we're on 2.4 GHz, then handle
this by disconnecting (with a reconnect hint).
When we disconnect, we'll also update our capabilities to use
only 20 MHz on the next connection (if it's on 2.4 GHz) as to
avoid the use of the extension channel that has too much noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4de9c363b0b5.I709b7e6f73a7537c53f22d7418927691259de8a8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For testing features where the firmware may send some
notifications it can often be a lot easier to do that
from a test script. Remove most injection limitations
from debugfs to be able to do this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.9aff3c6b4607.I03b0ae7df094734451445ffcb7f9f0274969f1c0@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
We're currently doing accounting on the queue sync with an
atomic variable that counts down the number of remaining
notifications that we still need.
As we've been hitting issues in this area, modify this to
track a bitmap of queues, not just the number of queues,
and print out the remaining bitmap in the warning.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.0a3fa177cd6b.I7c69ff999419368266279ec27dd618eb450908b3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The argument type to iwl_mvm_notify_rx_queue() is currently just
a u8 *, but that's misleading because we actually need the inner
data to be of type struct iwl_mvm_internal_rxq_notif, because we
interpret it when we get it back from the device (to check the
sync bool and possibly the cookie.)
Therefore, clear up any potential confusion and require that the
data passed is of type struct iwl_mvm_internal_rxq_notif *.
Also, while at it, rename the "count" to "notif_size" as "count"
doesn't really clearly say what it's counting.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201209231352.d28e14682bdc.I9ac366aa97db045be4daa4ba263267a3ac6a6a2f@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add support to the 6GHz band (aka. Ultra High Band or UHB). This
allows us to scan and connect to channels in that band, including all
the relevant features, such as preferred scan channels, colocated
channels etc.
Co-developed-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Co-developed-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Co-developed-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Co-developed-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: Andrei Otcheretianski <andrei.otcheretianski@intel.com>
Co-developed-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com>
Signed-off-by: Tali Levi Rovinsky <Tali.Levi-rovinsky@intel.com>
Co-developed-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Co-developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20201210000657.0fdbfc3d7352.Idb648536faf21716e2ab2c6d6890d3e49f719cd3@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As part of changes made to properly support auxiliary activities in CDB
NICs, an aux sta will be added when using hot spot 2.0 and will need
to be removed when roc flow is done.
In order to do so, prepare the roc_done_wk to work synchronously as the
rm_aux_sta is a SYNC command.
Since now all of th iwl_mvm_flush_sta function are using it sync,
removed the flag argument from the function.
Signed-off-by: Nathan Errera <nathan.errera@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/iwlwifi.20201008180656.71b441c8b682.Ia1d216cb680308b91d6da9f73e23ae9f4baac79f@changeid
Add an option for adding a PASN responder, specifying the HLTK and
TK (if not associated). When a receiving a range request for a
PASN responder, the driver will ask for a secured measurement with
the specified HLTK and TK.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.28c5f5266000.I2d58b72ff92c47ac33a6aacc27fbf3790b6dfc51@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The overcome instabilities in the RTT results add smoothing logic
to the reported results. In short, the smoothing logic tracks the
RTT average of each responder for a period of time, and in case
a new RTT results is found to be a spur, the tracked RTT average
is reported instead of the current RTT measurement.
Smooth logic debug configuration using iwl-dbg-cfg.ini:
- MVM_FTM_INITIATOR_ENABLE_SMOOTH: Set to 1 to enable smoothing logic
(default=0).
- MVM_FTM_INITIATOR_SMOOTH_ALPHA: A value between 0 - 100, defining
the weight of the current RTT results vs. the RTT average tracked
based on the previous results. A value of 100 means use only the
current RTT results.
- MVM_FTM_INITIATOR_SMOOTH_AGE_SEC: The maximal time in seconds in which
the RTT average tracked based on previous results is considered valid.
- MVM_FTM_INITIATOR_SMOOTH_UNDERSHOOT: if the current RTT is positive
and below the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
- MVM_FTM_INITIATOR_SMOOTH_OVERSHOOT: if the current RTT is positive
and above the RTT average by at least this value, report the average
RTT instead of the current one. In units of picoseconds.
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200930161256.48a9cec2081b.Iaec1e29f738232adfe9e2ea8e9eb9b6ff0323ae1@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Version 11 of the range request command adds support for setting
the PN for secure ranging. For now, this is not yet supported.
The same functions that are used for version 9 and 10 are also
used for version 11 as the common part is the same.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.6f9ed4140e8c.I046e0d9f6dfaafda9794e5eb2ee1f02fcad2851a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
For new APIs this avoids checking every return if it's
IWL_FW_CMD_VER_UNKNOWN (99) or it's lower than the new API value
Done with spatch:
-iwl_fw_lookup_cmd_ver(E1, E2, E3)
+iwl_fw_lookup_cmd_ver(E1, E2, E3, IWL_FW_CMD_VER_UNKNOWN)
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.70bec6eb8008.I6ea78553801d33f7ed10fcd2e4be4ba781fe469a@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the version number to the iwl_geo_tx_power_profile_cmd structs and
move the union into a common place. Additionally, reuse the code that
sets elements that are at the same place in the struct across
different versions.
While at it remove an unused variable, add a comment and move the v2
specific element setting to inside the if statement. Additionally,
invert the if for slightly more readability.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200928121852.23ec241f16cd.I8cd21fc5a2498e820b50e1f49a4cbfe545afe30e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently we have the same info in two variables,
If umac_error_event_table is 0, we know that UMAC log is not supported,
so we don't need the support_umac_log field.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.299959eeb47b.Ie1f3eecc06e3620098dda74f674f6409b90fe7fa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A FTM responder may do PASN authentication with unassociated stations
to allow secure ranging. In this case, the driver will add an internal
station and install the TK so the FW will accept protected FTM
request frames from this station and will send a protected FTM
response frame.
In addition, the driver needs to configure the HLTK to the FW so
the FW can derive the secure LTF bits. This is left for a later
patch since it is not yet supported by the FW.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200911204056.c915b44ad7dd.I72ef7f9753964555561c27ec503241105eddb14e@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The API version lookup is parsed from a TLV and should be in shared code
make make it reusable across all opmodes.
Also change the function names from mvm to fw, since this is not
mvm-specific anymore.
Additionally, since this function is not just a single line of code, it
shouldn't be inline. Convert them to actual functions.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200421133326.cf94672dfcdb.I5ede9cc25ee8de7b8d2b5c574f917a18971da734@changeid
The FW changed the maximum number of scan offload profiles to 8 in new
APIs. Support it by changing the scan_offload_profile_cfg struct to be
more dynamic, so we can reuse most of the code and only change size of
the profiles array.
Change-Id: I65210cf541af46e2675a8c764d5871f7f5b070d6
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJeLcWsAAoJEG4XJFUm622bDGUIAJuhM4LiDAzOGnDjH5cMosOC
/qwDpGD19cEeVAhNSMKUn7Uo9+qbQYIleiO7XXxzCuJceYbxbT5s3Vb/fWsRUPjS
cBDmGuK8/giqMQJshXvfCTsoF83CyirCjY/MJvomK2BRlXM8hQ3s6hAcfU0zQ96e
OU1akcfZzUwjaBKaDYLncxLuGbeUXMy8AZwFdgQlQRMoObpen/IIwx6jDK/A+3l6
VCOJF+JTkDytfNWmTpZ65uJrYEXoLe6G4028FjOI4BDFmEgvdHC5vTm7VOBhrkuB
9tsKcYNvECCNn2WI96V+etD8kaZPscQIW8hgOrYyGxw43lJg5zH4Z9eWAmHojxE=
=UOhb
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2020-01-26' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for v5.6
Second set of patches for v5.6. Nothing special standing out, smaller
new features and fixes allover.
Major changes:
ar5523
* add support for SMCWUSBT-G2 USB device
iwlwifi
* support new versions of the FTM FW APIs
* support new version of the beacon template FW API
* print some extra information when the driver is loaded
rtw88
* support wowlan feature for 8822c
* add support for WIPHY_WOWLAN_NET_DETECT
brcmfmac
* add initial support for monitor mode
qtnfmac
* add module parameter to enable DFS offloading in firmware
* add support for STA HE rates
* add support for TWT responder and spatial reuse
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an old parameter that was used supposed to be used only when
LAR was still under development. It should not be used anymore, but,
since it's available, end-users have been mangling with it
unnecessarily. In some cases it can cause problems because when LAR
is supported the driver and the firmware do not expect it to be
disabled.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
When we transmit after TXQ dequeue, we aren't paying attention to
the return value of the transmit functions, leading to a potential
SKB leak.
Refactor the code a bit (and rename ..._tx to ..._tx_sta) to check
for this happening.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Fixes: cfbc6c4c5b ("iwlwifi: mvm: support mac80211 TXQs model")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This fixes a long-standing bug - we haven't been able to check the
firmware image that was loaded for D3/not-D3 since the introduction
of the unified image...
Fix this by keeping a status flag for D3 instead of checking for
the firmware image that's loaded.
This reduces occurrences of checks for IWL_UCODE_WOWLAN to just the
code that actually loads the image or deals with it in other ways.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Refactored the SAR related functions from iwlmvm to acpi
in order to make it shared between different opmodes
in addition to removing unused variable ppag_rev.
Signed-off-by: Ihab Zhaika <ihab.zhaika@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Implement a new versioning handling flow supported from version 11
onwards.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW scan api ver 11 adds support for some new features,
in this version the fw did also some cleanup in the api,
which causes the driver not to be able to use the
current scan req struct.
Therefore, in this patch the driver has new version for the scan command
code
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdwYyqAAoJEG4XJFUm622b/jMH/0KUcGz8y4gkk2B2lMRyUOTu
t84LiSHxcsq6letlr/vak4S6NrxMLP8Z/ByyoKC8o3yeVsdyMNMSLZAztFFhxdXr
Haky2SM10q6vnn9s1skXS/qkHSd2WdUFT2DgYxyOPCtJUazVKjcboJ4YX/TUg99a
5eqPpZ4RXtW6uOmWHS7JXtLcCFPywKPBtMAjLEDMYOUSSBWExBNyNZNhznSS3ywY
4VKvc675gXE+WD3qXRhL8EJjyed94yuS3wYbKWp8iTaIRyluDmc5lVhjWH1A0HLE
Qb62QL8XLtbX5fcTnaupdAIXwxeIBylOBe8QtW7QUbAnGFf8bexLxfnQM+To4wI=
=24zD
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-2019-11-05' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.5
First set of patches for 5.5. The most active driver here clearly is
rtw88, lots of patches for it. More quiet on other drivers, smaller
fixes and cleanups all over.
This pull request also has a trivial conflict, the report and example
resolution here:
https://lkml.kernel.org/r/20191031111242.50ab1eca@canb.auug.org.au
Major changes:
rtw88
* add deep power save support
* add mac80211 software tx queue (wake_tx_queue) support
* enable hardware rate control
* add TX-AMSDU support
* add NL80211_EXT_FEATURE_CAN_REPLACE_PTK0 support
* add power tracking support
* add 802.11ac beamformee support
* add set_bitrate_mask support
* add phy_info debugfs to show Tx/Rx physical status
* add RFE type 3 support for 8822b
ath10k
* add support for hardware rfkill on devices where firmware supports it
rtl8xxxu
* add bluetooth co-existence support for single antenna
iwlwifi
* Revamp the debugging infrastructure
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The API was reduced to include only knowledge currently needed by the
FW scan logic, the rest is legacy. Support the new, reduced version.
Using the old API with newer firmwares (starting from
iwlwifi-*-50.ucode, which implements and requires the new API version)
causes an assertion failure similar to this one:
[ 2.854505] iwlwifi 0000:00:14.3: 0x20000038 | BAD_COMMAND
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The FW introduce new API to get the band from the rx mpdu,
use this new API.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A missed VAP notification will be sent from umac when
the station is out of sync with its associated non-transmitted
BSSID. The notification will be sent only if the transmitted
BSSID is an EMA-AP one.
The driver will consider this notification as connection loss.
Signed-off-by: Lior Cohen <lior2.cohen@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
During D3 state there are some flows which requires FW reset.
Add new API to support it.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
