Conceptually, this belongs more into the firmware utils
rather than the mvm opmode, so move the collection and
output there.
Note that this slightly changes the format of the Status
line.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210621103449.b82b60d81346.Ide3b688107f6a59c7fc7eb1d8f2002b0a5c1f2d2@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
SMPS requests may differ per interfaces due to e.g. Bluetooth
only interfering on 2.4 GHz, so if that's the case we should,
in the case of multiple PHY contexts, still allow RX diversity
on PHY context that have no interfaces with SMPS requests.
Fix the code to pass through the PHY context in question and
skip interfaces with non-matching PHY context while iterating.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210617100544.123c6b05809d.I992e3d1c6a29850d02eeec01712b5b685b963a87@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
D3_CONFIG_CMD and D0I3_END_CMD should be the last\first
command upon suspend\resume correspondingly, otherwise,
FW will raise an assert (0x342).
There are firmware notifications that cause the driver to
send a command back to the firmware. If such a notification
is sent to the driver while the the driver prepares the
firmware for D3, operation, what is likely to happen is that
the handling of the notification will try to get the mutex
and will wait unil the driver finished configuring the
firmware for D3. Then the handling notification will get
the mutex and handle the notification which will lead to
the aforementioned ASSERT 342.
To avoid this, we need to prevent any command to be sent to
the firmware between the D3_CONFIG_CMD and the D0I3_END_CMD.
Check this in the utility layer that sends the host commands
and in the transport layer as well.
Flag the D3_CONFIG_CMD and the D0I3_END_CMD commands as
commands that must be sent even if the firmware has already
been configured for D3 operation.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117164916.1935a993b471.I3192c93c030576ca16773c01b009c4d93610d6ea@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
If there are frequent CCA delays due to the extension channel
as detected by the firmware, and we're on 2.4 GHz, then handle
this by disconnecting (with a reconnect hint).
When we disconnect, we'll also update our capabilities to use
only 20 MHz on the next connection (if it's on 2.4 GHz) as to
avoid the use of the extension channel that has too much noise.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210117130510.4de9c363b0b5.I709b7e6f73a7537c53f22d7418927691259de8a8@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Fix misnamed, and missing descriptions likely due to doc-rot.
Fixes the following W=1 kernel build warning(s):
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Function parameter or member 'lq' not described in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:669: warning: Excess function parameter 'sync' description in 'iwl_mvm_send_lq_cmd'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'mvm' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'vif' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Function parameter or member 'smps_request' not described in 'iwl_mvm_update_smps'
drivers/net/wireless/intel/iwlwifi/mvm/utils.c:695: warning: Excess function parameter 'smps_requests' description in 'iwl_mvm_update_smps'
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Cc: Luca Coelho <luciano.coelho@intel.com>
Cc: Intel Linux Wireless <linuxwifi@intel.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20200910065431.657636-11-lee.jones@linaro.org
Currently we have the same info in two variables,
If umac_error_event_table is 0, we know that UMAC log is not supported,
so we don't need the support_umac_log field.
Signed-off-by: Mordechay Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20200926002540.299959eeb47b.Ie1f3eecc06e3620098dda74f674f6409b90fe7fa@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
OFDM rate used for all bands except to band 2.4 which use CCK rate.
Inverting the condition help that in future we won't need to expand the
condition for more bands.
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Stop accessing the trans configuration via the iwl_cfg structure and
always access it via the iwl_trans structure. This completes the
requirements to disassociate the trans-specific configuration from the
rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add a pointer to the iwl_trans structure and point it to the trans
part of the cfg. This is the first step in disassociating the trans
configuration from the rest of the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In order to be able to select the cfg depending on the HW revision or
on the RF ID, we need to set up the trans before selecting the cfg.
To do so, move the elements from cfg that are needed by
iwl_trans_alloc() to a separate struct at the top of the cfg, so it
can be used by other cfg types as well, before selecting the rest of
the configuration.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The only place where the command was sent as SYNC is during
init and this is not really critical. This change is required
for replacing RS mutex with a spinlock (in the subsequent patch),
since SYNC comamnd requres sleeping and thus the flow cannot
be done when holding a spinlock.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pull networking updates from David Miller:
"Some highlights from this development cycle:
1) Big refactoring of ipv6 route and neigh handling to support
nexthop objects configurable as units from userspace. From David
Ahern.
2) Convert explored_states in BPF verifier into a hash table,
significantly decreased state held for programs with bpf2bpf
calls, from Alexei Starovoitov.
3) Implement bpf_send_signal() helper, from Yonghong Song.
4) Various classifier enhancements to mvpp2 driver, from Maxime
Chevallier.
5) Add aRFS support to hns3 driver, from Jian Shen.
6) Fix use after free in inet frags by allocating fqdirs dynamically
and reworking how rhashtable dismantle occurs, from Eric Dumazet.
7) Add act_ctinfo packet classifier action, from Kevin
Darbyshire-Bryant.
8) Add TFO key backup infrastructure, from Jason Baron.
9) Remove several old and unused ISDN drivers, from Arnd Bergmann.
10) Add devlink notifications for flash update status to mlxsw driver,
from Jiri Pirko.
11) Lots of kTLS offload infrastructure fixes, from Jakub Kicinski.
12) Add support for mv88e6250 DSA chips, from Rasmus Villemoes.
13) Various enhancements to ipv6 flow label handling, from Eric
Dumazet and Willem de Bruijn.
14) Support TLS offload in nfp driver, from Jakub Kicinski, Dirk van
der Merwe, and others.
15) Various improvements to axienet driver including converting it to
phylink, from Robert Hancock.
16) Add PTP support to sja1105 DSA driver, from Vladimir Oltean.
17) Add mqprio qdisc offload support to dpaa2-eth, from Ioana
Radulescu.
18) Add devlink health reporting to mlx5, from Moshe Shemesh.
19) Convert stmmac over to phylink, from Jose Abreu.
20) Add PTP PHC (Physical Hardware Clock) support to mlxsw, from
Shalom Toledo.
21) Add nftables SYNPROXY support, from Fernando Fernandez Mancera.
22) Convert tcp_fastopen over to use SipHash, from Ard Biesheuvel.
23) Track spill/fill of constants in BPF verifier, from Alexei
Starovoitov.
24) Support bounded loops in BPF, from Alexei Starovoitov.
25) Various page_pool API fixes and improvements, from Jesper Dangaard
Brouer.
26) Just like ipv4, support ref-countless ipv6 route handling. From
Wei Wang.
27) Support VLAN offloading in aquantia driver, from Igor Russkikh.
28) Add AF_XDP zero-copy support to mlx5, from Maxim Mikityanskiy.
29) Add flower GRE encap/decap support to nfp driver, from Pieter
Jansen van Vuuren.
30) Protect against stack overflow when using act_mirred, from John
Hurley.
31) Allow devmap map lookups from eBPF, from Toke Høiland-Jørgensen.
32) Use page_pool API in netsec driver, Ilias Apalodimas.
33) Add Google gve network driver, from Catherine Sullivan.
34) More indirect call avoidance, from Paolo Abeni.
35) Add kTLS TX HW offload support to mlx5, from Tariq Toukan.
36) Add XDP_REDIRECT support to bnxt_en, from Andy Gospodarek.
37) Add MPLS manipulation actions to TC, from John Hurley.
38) Add sending a packet to connection tracking from TC actions, and
then allow flower classifier matching on conntrack state. From
Paul Blakey.
39) Netfilter hw offload support, from Pablo Neira Ayuso"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2080 commits)
net/mlx5e: Return in default case statement in tx_post_resync_params
mlx5: Return -EINVAL when WARN_ON_ONCE triggers in mlx5e_tls_resync().
net: dsa: add support for BRIDGE_MROUTER attribute
pkt_sched: Include const.h
net: netsec: remove static declaration for netsec_set_tx_de()
net: netsec: remove superfluous if statement
netfilter: nf_tables: add hardware offload support
net: flow_offload: rename tc_cls_flower_offload to flow_cls_offload
net: flow_offload: add flow_block_cb_is_busy() and use it
net: sched: remove tcf block API
drivers: net: use flow block API
net: sched: use flow block API
net: flow_offload: add flow_block_cb_{priv, incref, decref}()
net: flow_offload: add list handling functions
net: flow_offload: add flow_block_cb_alloc() and flow_block_cb_free()
net: flow_offload: rename TCF_BLOCK_BINDER_TYPE_* to FLOW_BLOCK_BINDER_TYPE_*
net: flow_offload: rename TC_BLOCK_{UN}BIND to FLOW_BLOCK_{UN}BIND
net: flow_offload: add flow_block_cb_setup_simple()
net: hisilicon: Add an tx_desc to adapt HI13X1_GMAC
net: hisilicon: Add an rx_desc to adapt HI13X1_GMAC
...
Unite iwl_trans debug related fields under iwl_trans_debug struct to
increase readability and keep iwl_trans clean.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The indexes into the ac array in the iwl_mac_ctx_cmd are from the iwl_ac
enum and not the txfs. The current code therefore puts the edca params
in the wrong indexes of the array, causing wrong priority for
data-streams of different ACs.
Fix this.
Note that this bug only occurs in NICs that use the new tx api, since in
the old tx api the txf number is equal to the corresponding ac in the
iwl_ac enum.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
This makes boot uniformly boottime and tai uniformly clocktai, to
address the remaining oversights.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lkml.kernel.org/r/20190621203249.3909-2-Jason@zx2c4.com
Read fseq info from FW registers and print it upon fw assert.
The print is needed since the fseq version coming from the TLV might
not be the actual version that is used.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The device time register address has changed for 22000 devices.
Add a util function for getting the GP2 time and use the correct
register address depending on the device family.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
TLV 54 holds umac debug related addresses.
TLV 55 holds lmac debug related addresses.
These TLVs aim to replace the alive notification data in the future.
Parse and keep error table addresses received from the TLVs
for both lmac and umac and use these addresses instead of the pointer
received from alive notification.
The feature supports only unified image.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The typical sequence of setting INIT_DONE and then waiting
for clock stabilisation is going to need a new workarounds,
so first of all refactor it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Depending on exactly what happens in the FW, an invalid host-command
could result in either assert 0x38 or 0x39. Add 0x39 to the assert-name
table.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Currently whenever we get firmware notification with mac id,
we iterate over all the interfaces to find the ID. This is a
bit cumbersome. Instead, adding an array of RCU pointers, like
we have for station IDs. This is not expensive space wise
since we have only up to 4 active MACs, and not complicated
code wise, since we have a clear point to init and de-init it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
With just %16, it means 16 characters padding, but we really
don't want to print "0x 1F4547B", but instead want to
have this filled with zeroes, so we need the 0.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add to the dump the number of lmacs, the error id of the umac
and the error id of lmac1, if supported.
In case the reason for the dump trigger is not an assert
the error id is zero.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Add the rt status of the last assert or 0 if the dump collection was
not initiated by an assert. Add the number of rx and tx fifos in use.
These fields are added to dump info lst file.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When traffic load is not low or low latency is active, TCM schedules
re-evaluation work so in case traffic stops TCM will detect that
traffic load has become low or that low latency is no longer active.
However, if TCM is paused when the re-evaluation work runs, it does
not re-evaluate and the re-evaluation work is no longer scheduled.
As a result, TCM will not indicate that low latency is no longer
active or that traffic load is low when traffic stops.
Fix this by forcing TCM re-evaluation when TCM is resumed in case
low latency is active or traffic load is not low.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
FW asserts 0x70, 0x71, and 0x73 all just mean that the real error
happened in another MAC, and to look there for the problem. Add their
descriptions to the assert number lookup table so users get a nicer
error message in the logs.
Also, since the 4 most-significant bits of the assert number are
dynamic, and depend on which MAC the assert occurred on, ignore those
bits when looking up the assert name.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Enable low latency for softAP in all modes (standalone, SCM
and DCM).
This is in order to minimize the time the softAP leaves the channel for
other operations
Signed-off-by: Tova Mussai <tova.mussai@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
All the queue management code runs under mvm->mutex, so there are
only very few cases of accessing the data structures without it:
* TX path, which doesn't take any locks anyway
* iwl_mvm_wake_sw_queue() and iwl_mvm_stop_sw_queue() where we
just (atomically) read a bitmap, so the lock isn't needed.
Therefore, we can remove the spinlock. This enables some cleanup
in the ugly locking in iwl_mvm_inactivity_check().
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There's no need to have a hw refcount if we just mark the
command queue with a (fake) TID; at that point, the refcount
becomes equivalent to the hweight() of the TID bitmap.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
None of these functions really need to be separate, they're all
only used in sta.c, move them there and make them static.
Fix a small typo in related code while at it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The triplet of get trigger, is trigger enabled and is trigger stopped
repeats itself. Group them in a function to avoid code duplication.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Alexei's patch, assumed that all versions of "struct iwl_error_event_table"
are the same, but there are really different versions in different files.
Rather than trying to fix this, or splitting the tracepoint, or anything of
the sort, just remove it entirely - turns out that nobody really uses it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Support more txq_alloc command types by moving the command declaration
to the gen specific area. While at it, move some of the code segments
to a common place for re-use.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The Free Software Foundation address is superfluous and causes
checkpatch to issue a warning when present. Remove all paragraphs
with FSF's address to prevent that.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
The parameter that indicated whether the LQ command should be sent
as sync or async was removed, causing the LQ command to be sent as
sync from interrupt context (e.g. from the RX path). This resulted
in a kernel warning: "scheduling while atomic" and failing to send
the LQ command, which ultimately leads to a queue hang.
Fix it by adding back the required parameter to send the command as
sync only when it is allowed.
Fixes: d94c5a820d ("iwlwifi: mvm: open BA session only when sta is authorized")
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Different device families may have different flag values
for passing a message to the fw (i.e. SW_RESET).
In order to keep the code readable, and avoid conditioning
upon the family, store a value for each flag, which indicates
the bit that needs to be enabled.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Update rs-fw API to match changes in FW. Specifically, the
TLC_MNG_NOTIF_REQ_CMD command and TLC_MNG_AMSDU_ENABLE_NOTIF
notification are removed, the A-MSDU related info is received from FW
via the TLC_MNG_UPDATE_NOTIF, and the TLC_MNG_CONFIG_CMD uses version
2 of its data structure.
Additionally, constify some arguments in a couple of functions.
Signed-off-by: Naftali Goldstein <naftali.goldstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
In 22000 devices, aka gen2, the TFS is 256 bytes.
In order to save memory, use shorter TX queue for aux and
mgmt queues, since there isn't much traffic on them.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
As preparation for dynamic queue sizing, add a parameter
of the TX queue size to the dynamic queue allocation op
mode API.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
