The MCTP LPC driver was loaded by hacking up the compatible in the
devicetree node for KCS 4. With the introduction of the raw KCS driver
this hack is no-longer required. Use the regular compatible string for
KCS 4 and configure the appropriate SerIRQ.
The reset state of the status bits on KCS 4 is inappropriate for the
MCTP LPC binding. Switch to KCS 3 which has a different reset behaviour.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set I2C bus 14 to multi-master mode and add the panel device that will
register the I2C controller as a slave device.
In addition, in early Everest systems, the panel device was behind an
I2C switch, which doesn't work for slave mode. Get it working (albeit
unreliably, since a master transaction might switch the switch at any
moment) by defaulting the switch channel to the one with the panel.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-5-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Specifying gpio nodes under PCA led controllers no longer does anything,
so remove those nodes in the device trees.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-3-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
In keeping with previous systems, call the iio-hwmon bridge node
"iio-hwmon-battery" to distinguish it as the battery voltage
sensor.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20211020215321.33960-2-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Input pin that indicates that the BMC is configured to boot with security
protections enforced.
Pulled up by default (secure). Placing the jumper will pull the pin down
(bypass security).
When in the secure boot state, it makes the EEPROM at 0x50 on bus 14
read only.
Link: https://lore.kernel.org/r/20210923074606.283393-1-joel@jms.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the ADC nodes to the AST2600 devicetree. Enable ADC1 for Rainier and
Everest systems and add an iio-hwmon node for the 7th channel to report
the battery voltage.
Tested on Rainier:
~# cat /sys/class/hwmon/hwmon11/in1_input
1347
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210916210045.31769-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
The state of this GPIO determines whether a factory reset has been
requested. If a physical switch is used, it can be high or low. During boot,
the software checks and records the state of this switch. If it is different
than the previous recorded state, then the read-write portions of memory are
reformatted.
Signed-off-by: Isaac Kurth <isaac.kurth@ibm.com>
Link: https://lore.kernel.org/r/20210901185236.558771-1-isaac.kurth@ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Fix all the remaining dtc 'unit_address_format' warnings except for the ones
related to 'register-bit-led'. For those, we need to decide on and document
the node name.
Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210823165126.2320910-1-robh@kernel.org'
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The GPIO is used to place the BMC-connected TPM in reset. This state is
latched until the BMC is next reset, blocking access to the TPM for that
boot.
On both machines this net is called TPM_RESET_LATCH_B.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210727033319.473152-2-joel@jms.id.au
The values were determined via scope measurements.
With the patch we can write and read data without issue where as booting
the system without the patch failed at the point of mounting the rootfs.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210712233642.3119722-1-andrew@aj.id.au
Fixes: faffd1b2bd ("ARM: dts: everest: Add phase corrections for eMMC")
Signed-off-by: Joel Stanley <joel@jms.id.au>
The third power supply had an I2C address conflict with another device
in the system. The device will have the address changed from 6Ah to 6Dh.
Signed-off-by: B. J. Wyman <bjwyman@gmail.com>
Reviewed-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210610202940.3650554-1-bjwyman@gmail.com
Fixes: d66d720b64 ("ARM: dts: aspeed: everest: Add power supply i2c devices")
Signed-off-by: Joel Stanley <joel@jms.id.au>
The values were determined experimentally via boot tests, not by
measuring the bus behaviour with a scope. We plan to do scope
measurements to confirm or refine the values and will update the
devicetree if necessary once these have been obtained.
However, with the patch we can write and read data without issue, where
as booting the system without the patch failed at the point of mounting
the rootfs.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210628013605.1257346-1-andrew@aj.id.au
Fixes: 2fc88f9235 ("mmc: sdhci-of-aspeed: Expose clock phase controls")
Fixes: a5c5168478 ("ARM: dts: aspeed: Add Everest BMC machine")
Signed-off-by: Joel Stanley <joel@jms.id.au>
These are leds on the IBM proprietary PCIE cards called cable cards.
Cable cards have 2 ports on them and each port has an indicator led.
Signed-off-by: Vishwanatha Subbanna <vishwa@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210607031259.475020-7-joel@jms.id.au
This commit adds indicator leds for vrms, processors, opencapi
connectors, tpm, planar, power distribution card and dasd
backplane and are driven by PIC16F882.
Signed-off-by: Vishwanatha Subbanna <vishwa@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210607031259.475020-6-joel@jms.id.au
These are the indicator leds for nvme slots and fans and are
driven by PCA9552.
Signed-off-by: Vishwanatha Subbanna <vishwa@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210607031259.475020-3-joel@jms.id.au
These are the system level indicator leds that are driven by
PCA9551 connected to the Operator Panel.
Signed-off-by: Vishwanatha Subbanna <vishwa@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210607031259.475020-2-joel@jms.id.au
These LEDs are directly connected to the BMC's GPIO bank
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Vishwanatha Subbanna <vishwa@linux.vnet.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Correct two PCA chips which were placed on the wrong I2C bus and
address.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Santosh Puranik <santosh.puranik@in.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
Set watchdog 1 to pulse the fan watchdog circuit that drives the FAULT
pin of the MAX31785, resulting in fans running at full speed, if at
any point the BMC stops pulsing it, such as a BMC reboot at runtime.
Enable watchdog 2 for BMC reboots.
Signed-off-by: Matthew Barth <msbarth@linux.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210329150020.13632-21-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
This commit adds support for-
- Presence GPIOs
- I2C control GPIOs
- Op-panel GPIOs (ex PHR)
Signed-off-by: Alpana Kumari <alpankum@in.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20210329150020.13632-19-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the i2c/pmbus power supply devices to the everest device tree.
Signed-off-by: Brandon Wyman <bjwyman@gmail.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210329150020.13632-17-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the pca9552 at address 0x61 on i2c14 behind mux0 channel 3 with the
4 GPIO fan presence inputs.
Signed-off-by: Matthew Barth <msbarth@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Reviewed-by: Brandon Wyman <bjwyman@gmail.com>
Link: https://lore.kernel.org/r/20210329150020.13632-16-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add additional CFAMs and re-number the existing engines for the
extra processors present on the Everest system.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210329150020.13632-15-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the max31785 configuration at address 0x52 on i2c14 behind mux0
channel 3.
Signed-off-by: Matthew Barth <msbarth@us.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210329150020.13632-14-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Tested and able to bound the devices with i2c driver.
Signed-off-by: Priyanga Ramasamy <priyanga24@in.ibm.com>
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210329150020.13632-13-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
Add the Everest machine powered by an AST2600 chip. Copy the basic
configuration from Rainier.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Andrew Geissler <geissonator@gmail.com>
Link: https://lore.kernel.org/r/20201211170704.27640-1-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
