[WHY]
On certain configs, SMU clock table voltages don't match which cause parser
to behave incorrectly by leaving dcfclk and socclk table entries unpopulated.
[HOW]
Currently the function that finds the corresponding clock for a given voltage
only checks for exact voltage level matches. In the case that no match gets
found, parser now falls back to searching for the max clock which meets the
requested voltage (i.e. its corresponding voltage is below requested).
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is unnecessary in clk_mgr
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
To expose new power optimization flags to PSR interface. It allows the
PSR related power features can be enabled separately base on different
use scenarios.
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Agustin Gutierrez <agustin.gutierrez@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Robin Chen <po-tchen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The original latencies were causing underflow in some modes
[how]
Replace with the up-to-date watermark values based on new measurments
Reviewed-by: Ahmad Othman <ahmad.othman@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Disable root clock for dpp when not being used.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Agustin Gutierrez Sanchez <agustin.gutierrez@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Remove all but the first include of reg_helper.h and core_types.h
from dcn201_clk_mgr.c.
Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Lv Ruyi <lv.ruyi@zte.com.cn>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
add display related cyan_skillfish files in.
makefile controlled by CONFIG_DRM_AMD_DC_DCN201 flag.
v2: squash in clang fixes from Harry, Nathan
v3: squash in missing CONFIG_DRM_AMD_DC check (Alex)
Signed-off-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Acked-by: Jun Lei <jun.lei@amd.com>
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
DC should be used in place of DAL in
upstream.
[How]
Replace dal with dc in function names.
Reviewed-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Signed-off-by: Qingqing Zhuo <Qingqing.Zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
If DCN30 watermark calc is used for DCN301, the calculated values are
wrong due to the data structure mismatch between DCN30 and DCN301.
However, using the original DCN301 watermark values causes underflow.
[how]
- Add DCN21-style watermark calculations
- Adjust DCN301 watermark values to remove the underflow
Reviewed-by: Zhan Liu <zhan.liu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD disable and enable sequences are not mutually exclusive on Linux.
For HPDs that spans under 1s (i.e. HPD low = 1s), part of the disable
sequence (specifically, a request to SMU to lower refclk) could come
right before the call to PHY enablement, causing DMUB to access an
irresponsive PHY and thus a hard hang on the system.
[How]
Disable 48mhz refclk off when there is any HPD status in connected state
for dcn20.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When system is in Z10 HPD interrupts cannot fire, we may miss display
configuration changes.
[How]
When Zstate is enabled, if DMUB indicate DCN has lost power, do a
complete detection periodically.
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans under 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enablement, causing DMUB to access an irresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off when there is any HPD status in
connected state.
Reviewed-by: Hersen Wu <hersenwu@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit "drm/amd/display: w/a for hard hang on HPD on native DP".
[How & Why]
Revert change as it does not fix the hard hang
in all cases. An alternative w/a will be submitted
separately.
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Reviewed-by: Bhawanpreet Lakha <bhawanpreet.lakha@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Assuming DIG link encoders are statically mapped to links can cause
system instability due to null pointer accesses.
[How]
- Add checks for non-null link encoder pointers before trying to access
them.
- When a hardware platform uses dynamic DIG assignment (i.e. resource
function 'link_encs_assign' defined) and a link supports flexible
mapping to DIGs, use the link_enc_cfg API to access the DIG assigned to
a link or stream.
Reviewed-by: Meenakshikumar Somasundaram <meenakshikumar.somasundaram@amd.com>
Acked-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Jimmy Kizito <Jimmy.Kizito@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
HPD disable and enable sequences are not mutually exclusive
on Linux. For HPDs that spans over 1s (i.e. HPD low = 1s),
part of the disable sequence (specifically, a request to SMU
to lower refclk) could come right before the call to PHY
enable, causing DMUB to access an unresponsive PHY
and thus a hard hang on the system.
[How]
Disable 48mhz refclk off on native DP.
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We don't check DENTIST_DISPCLK_CHG_DONE to ensure dentist
display clockis updated to target value. In some scenarios with large
display clock margin, it will deliver unfinished display clock and cause
issues like display black screen.
[How]
Checking DENTIST_DISPCLK_CHG_DONE to ensure display clock
has been update to target value before driver do other clock related
actions.
Reviewed-by: Cyr Aric <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Dale Zhao <dale.zhao@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
PMFW message which previously thought to only control Z9 controls both
Z9 and Z10. Also HW design team requested that Z9 must only be supported
on eDP due to content protection interop.
[How]
Change zstate support condition to match updated policy
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Eric Yang <Eric.Yang2@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Hardcoding the VCO frequency isn't correct since we don't own or control
the value.
In the case where the hardcode is also missing we can't lightup display.
[How]
Query from the CLK register instead. Update the DFS frequency to be able
to compute the VCO frequency.
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Initialize socclk entries in bandwidth params for dcn302, dcn303.
[How]
Fetch the sockclk values from smu for the DPM levels and for the DPM
levels where smu returns 0, previous level values are reported.
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Lowering clocks when entering S2 Idle state causes DMUB to hang with
Diags.
[how]
Do not enter S2 optimization with Diags on dcn301 to prevent DMUB hang.
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When requesting clocks from SMU which takes MHz inputs, DC will round
down KHz when converting to MHz, thus potentially requesting too low a
clock value.
[How]
Round up (ceil) when converting KHz to MHz for clock requests to SMU.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
No need for a separate flag now that DCN3.1 is not in bring up.
Fold into DRM_AMD_DC_DCN like previous DCN IPs.
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
When changing the DISPCLK_WDIVIDER value from 126 to 127, the change in
clock rate is too great for the FIFOs to handle. This can cause visible
corruption during clock change.
HW has handed down this register sequence to fix the issue.
[HOW]
The sequence, from HW:
a. 127 -> 126
Read DIG_FIFO_CAL_AVERAGE_LEVEL
FIFO level N = DIG_FIFO_CAL_AVERAGE_LEVEL / 4
Set DCCG_FIFO_ERRDET_OVR_EN = 1
Write 1 to OTGx_DROP_PIXEL for (N-4) times
Set DCCG_FIFO_ERRDET_OVR_EN = 0
Write DENTIST_DISPCLK_RDIVIDER = 126
Because of frequency stepping, sequence a can be executed to change the
divider from 127 to any other divider value.
b. 126 -> 127
Read DIG_FIFO_CAL_AVERAGE_LEVEL
FIFO level N = DIG_FIFO_CAL_AVERAGE_LEVEL / 4
Set DCCG_FIFO_ERRDET_OVR_EN = 1
Write 1 to OTGx_ADD_PIXEL for (12-N) times
Set DCCG_FIFO_ERRDET_OVR_EN = 0
Write DENTIST_DISPCLK_RDIVIDER = 127
Because of frequency stepping, divider must first be set from any other
divider value to 126 before executing sequence b.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change was found to break some high-refresh modes. Reverting
to unblock mainline.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Updating PSR interfaces to allow PSR enablement
per eDP panel.
[how]
- Copying PSR command structures to DC
- Changing function interfaces to pass panel instance
- Communicating with DMUB per link instead of assuming
to use a single one
-Iterating through all PSR capable panels when enabling/disabling
all
Signed-off-by: Mikita Lipski <mikita.lipski@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Adds support for clock requests for the various parts of the DCN3.1 IP
and the interfaces and definitions for sending messages to SMU/PMFW.
Includes new support for z9/10, detecting SMU timeout and p-state
support enablement.
Acked-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previous patch caused crash and had been reverted. This patch
addresses the issue without regression.
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating.
Add additional delay time for single rank dimm.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
In some pipe harvesting configs, we will select the incorrect
dpp_inst when programming DTO. This is because when any intermediate
pipe is fused, resource instances are no longer in 1:1
correspondence with pipe index.
[How]
When looping through pipes to program DTO, get the dpp_inst
associated with each pipe from res_pool.
Signed-off-by: Anthony Wang <anthony1.wang@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Currently, the code that fills the clock table can miss filling
information about some of the higher voltage states advertised
by the SMU. This, in turn, may cause some of the higher pixel clock
modes (e.g. 8k60) to fail validation.
[How]
Fill the table with one entry per DCFCLK level instead of one entry
per FCLK level. This is needed because the maximum FCLK does not
necessarily need maximum voltage, whereas DCFCLK values from SMU
cover the full voltage range.
Signed-off-by: Ilya Bakoulin <Ilya.Bakoulin@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Stylon Wang <stylon.wang@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit "dc: treat memory as a single-channel for
asymmetric memory".
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Wayne Lin <Wayne.Lin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
This change only fix dpp clock switch to lower case.
New solution later can fix both case, which is "dc: skip
program clock when allow seamless boot"
[How]
This reverts commit "dc: wait vblank when stream enabled
and update dpp clock"
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Wayne Lin <waynelin@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[How & Why]
Changed "prsent" to "present".
Signed-off-by: David Galiffi <David.Galiffi@amd.com>
Reviewed-by: Chris Park <Chris.Park@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Previous change had been reverted since it caused hang.
Remake change to avoid defect.
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating.
Add additional delay time for single rank dimm.
Fixes: b8720ed0b8 ("drm/amd/display: System black screen hangs on driver load")
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Aurabindo Pillai <aurabindo.pillai@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When boot into OS, seamless boot device won't blank stream.
Driver update dpp clock when scanline position in vactive will show
garbage on screen.
[How]
Wait for vblank for seamless boot edp display when driver update dpp clock.
The apply seamless boot flag will be clear when OS call SetVisibility on.
Therefore we only wait for vblank once after boot into OS.
Signed-off-by: Lewis Huang <Lewis.Huang@amd.com>
Acked-by: Bindu Ramamurthy <bindur12@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add debug flag for an option to disable min fclk.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why&How]
Add debug prints for SMU messages with regard to
versions, clocks, and more.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Robin Singh <Robin.Singh@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Bring-up purpose code to disable DMUB calling into
SMU and timeout for MALL when SMU is not present.
[How]
Disable MALL when SMU is not present.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Dan Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The pmfw structs are specific to the asic and should not be
present in base clk_mgr struct
v2: squash in SI fix (Alex)
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Eric Yang <eric.yang2@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Dcn2.1 socclk entries in bandwidth params are not initialized.
They are not used now, but will be needed for dml validation.
[How]
Populate socclk bw params from dpm clock table
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Roman Li <roman.li@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
When unplugging a display, the underflow counter can be seen to
increase because PSTATE switch is allowed even when some planes are not
blanked.
[How]
Check that all planes are not active instead of all streams before
allowing PSTATE change.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This reverts commit dbc43d5fdf
as it causes crash on driver load in some scenarios.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Martin Leung <Martin.Leung@amd.com>
Acked-by: Solomon Chiu <solomon.chiu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
In some boot configurations we need to retrieve the currently
UEFI-set dppclk, but there was a typo in the calculation
[how]
Fix typo to make dpp_clk calculate off dpp_clk divider instead of
disp_clk
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
1. Driver use umachannelnumber to calculate watermarks for stutter.
In asymmetric memory config, the actual bandwidth is less than
dual-channel. The bandwidth should be the same as single-channel.
2. We found single rank dimm need additional delay time for stutter.
[How]
Get information from each DIMM. Treat memory config as a single-channel
for asymmetric memory in bandwidth calculating. Add additional delay
time for single rank dimm.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Some existing DC interfaces are optimized to return a single eDP
link/stream. Refactored those DC interfaces to support multiple eDP.
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Safeguarding as pointer may be null in diagnostic environment
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Reviewed-by: Sung Lee <Sung.Lee@amd.com>
Acked-by: Anson Jacob <Anson.Jacob@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
