Atm the DPT object can accommodate only one VMA, so the VMA offset will
be always 0. Add an assert for this.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906182715.3915100-4-imre.deak@intel.com
At the moment CCS FB strides must be power-of-two sized, but a follow-up
change will add support remapping these FBs, allowing the FB passed in
by userspace to have a non-POT sized stride. For these remapped FBs we
can only remap the main surface, not the CCS surface. This means that
userspace has to always generate the CCS surface aligning to the POT
stride padded main surface (by setting up the CCS AUX pagetables
accordingly). Adjust the CCS surface stride check to enforce this.
No functional change.
v2:
- Fix the gen12_ccs_aux_stride() is not static sparse warning.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906182715.3915100-3-imre.deak@intel.com
The tile size for all surface types is 4 kbyte (or 2 kbyte on old
platforms), with the exception of the TGL/ADL CCS surface where the tile
size is 64 bytes. To be able to remap CCS FBs the CCS surface tile needs
to be defined as 4 kbyte as well (the granularity of GTT pages in a
remapped view).
The only place using the dimension of the 64 byte CCS area is the initial
check for the main vs. CCS plane origin coordinate match. To prepare for
adding support for remapping CCS FBs let's call the 64 byte CCS area a
'tile block' and add a helper to retrieve the dimensions for it.
No functional change.
Cc: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Juha-Pekka Heikkila <juhapekka.heikkila@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210906182715.3915100-2-imre.deak@intel.com
Earlier while calculating derated bw we would use 90% of the calculated
bw. Starting ADL-P we use a non standard derating. Updating the formulae
to reflect the same.
Bspec: 64631
v2: Use the new derating value only for ADL-P(MattR)
Fixes: 4d32fe2f14 ("drm/i915/adl_p: Update memory bandwidth parameters")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914220744.16042-1-radhakrishna.sripada@intel.com
(cherry picked from commit f6d66fc8cf)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
128b/132b has a separate transcoder DDI mode, which also requires the
MST transport select to be set. Note that we'll use DP MST also for
single-stream 128b/132b.
Having the FDI and 128b/132b modes share the register mode value
complicates things a bit.
v2:
- Use HAS_DP20 abstraction for 128b/132b mode (Ville)
- Use intel_dp_is_uhbr() helper
Bspec: 50493
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/279bfbd979e0256fae13a5231e07e2f4fb665c07.1631191763.git.jani.nikula@intel.com
Wa_16014451276 fixes the starting coordinate for PSR2 selective
updates. CHICKEN_TRANS definition of the workaround bit has a wrong
name based on workaround definition and HSD.
Wa_14014971508 allows the screen to continue to be updated when
coming back from DC5/DC6 and SF_SINGLE_FULL_FRAME bit is not kept
set in PSR2_MAN_TRK_CTL.
Wa_16012604467 fixes underruns when exiting PSR2 when it is in one
of its internal states.
Wa_14014971508 is still in pending status in BSpec but by
the time this is reviewed and ready to be merged it will be finalized.
v2:
- renamed register to ADLP_1_BASED_X_GRANULARITY
- added comment about all ADL-P supported panels being 1 based X
granularity
BSpec: 54369
BSpec: 50054
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914212507.177511-5-jose.souza@intel.com
drm_atomic_helper_damage_iter_init() + drm_atomic_for_each_plane_damage()
returns the full plane area in case no damaged area was set by
userspace or it was discarted by driver.
This is important to fix the rendering of userspace applications that
does frontbuffer rendering and notify driver about dirty areas but do
not set any dirty clips.
With this we don't need to worry about to check and mark the whole
area as damaged in page flips.
Another important change here is the move of
drm_atomic_add_affected_planes() call, it needs to called late
otherwise the area of all the planes would be added to pipe_clip and
not saving power.
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914212507.177511-4-jose.souza@intel.com
Not sure why but when moving the cursor fast it causes some artifacts
of the cursor to be left in the cursor path, adding some pixels above
the cursor to the damaged area fixes the issue, so leaving this as a
workaround until proper fix is found.
This is reproducile on TGL and ADL-P.
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914212507.177511-3-jose.souza@intel.com
BSpec states that the minimum number of frames before selective update
is 2, so making sure this minimum limit is fulfilled.
BSpec: 50422
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914212507.177511-2-jose.souza@intel.com
The release notes mentions that this version-
1. Fix for unblock indication to punit.
2. Robustness fix for DC6/6v abort scenarios.
Cc: Imre Deak <Imre Deak <imre.deak@intel.com>>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914215732.67135-2-anusha.srivatsa@intel.com
Earlier while calculating derated bw we would use 90% of the calculated
bw. Starting ADL-P we use a non standard derating. Updating the formulae
to reflect the same.
Bspec: 64631
v2: Use the new derating value only for ADL-P(MattR)
Fixes: 4d32fe2f14 ("drm/i915/adl_p: Update memory bandwidth parameters")
Cc: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Radhakrishna Sripada <radhakrishna.sripada@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210914220744.16042-1-radhakrishna.sripada@intel.com
PIPECONF becamse TRANSCONF when HSW introduced the EDP transcoder.
Bigjoiner is making life even more confusing by introducing
a N:1 relationship between pipes and transcoders. In that case
we only enable/configure the transcoder corresponding to the
master pipe. Let's do some renames to make it clear we're dealing
with the transcoder rather than pipe when it comes to
PIPECONF/TRANSCONF.
I decided to leave the _cpu_ part out from the function/macro
names since the PCH transcoder related stuff already has a
_pch_ in their name. So shouldn't be possible to confuse them.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210913144440.23008-6-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Users reported that after commit 2bbd6dba84 ("drm/i915: Try to use
fast+narrow link on eDP again and fall back to the old max strategy on
failure"), the screen starts to have wobbly effect.
Commit a5c936add6 ("drm/i915/dp: Use slow and wide link training for
everything") doesn't help either, that means the affected eDP 1.2 panels
only work with max params.
So use max params for panels < eDP 1.4 as Windows does to solve the
issue.
v3:
- Do the eDP rev check in intel_edp_init_dpcd()
v2:
- Check eDP 1.4 instead of DPCD 1.1 to apply max params
Cc: stable@vger.kernel.org
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/3714
Fixes: 2bbd6dba84 ("drm/i915: Try to use fast+narrow link on eDP again and fall back to the old max strategy on failure")
Fixes: a5c936add6 ("drm/i915/dp: Use slow and wide link training for everything")
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210820075301.693099-1-kai.heng.feng@canonical.com
(cherry picked from commit d7f213c131)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
After DPRX link training, intel_dp_link_train_phy() did not
return the training result properly. If link training failed,
i915 driver would not run into link train fallback function.
And no hotplug uevent would be received by user space application.
Fixes: b30edfd8d0 ("drm/i915: Switch to LTTPR non-transparent mode link training")
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210706152541.25021-1-shawn.c.lee@intel.com
(cherry picked from commit dab1b47e57)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
On some Cherry Trail devices, DisplayPort over Type-C is supported through
a USB-PD microcontroller (e.g. a fusb302) + a mux to switch the superspeed
datalines between USB-3 and DP (e.g. a pi3usb30532). The kernel in this
case does the PD/alt-mode negotiation itself, rather then everything being
handled in firmware.
So the kernel itself picks an alt-mode, tells the Type-C "dongle" to switch
to DP mode and sets the mux accordingly. In this setup the HPD pin is not
connected, so the i915 driver needs to respond to a software event and scan
the DP port for changes manually.
This commit adds support for this. Together with the recent addition of
DP alt-mode support to the Type-C subsystem this makes DP over Type-C
work on these devices.
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210817215201.795062-7-hdegoede@redhat.com
On Intel platforms we know that the ACPI connector device
node order will follow the order the driver (i915) decides.
The decision is made using the custom Intel ACPI OpRegion
(intel_opregion.c), though the driver does not actually know
that the values it sends to ACPI there are used for
associating a device node for the connectors, and assigning
address for them.
In reality that custom Intel ACPI OpRegion actually violates
ACPI specification (we supply dynamic information to objects
that are defined static, for example _ADR), however, it
makes assigning correct connector node for a connector entry
straightforward (it's one-on-one mapping).
Changes in v2 (Hans de goede):
- Take a reference on the fwnode which we assign to the connector,
for ACPI nodes this is a no-op but in the future we may see
software-fwnodes assigned to connectors which are ref-counted.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Tested-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210817215201.795062-6-hdegoede@redhat.com
On some MST docking stations, rx_info can only be read after
RepeaterAuth_Send_ReceiverID_List and the RxStatus READY bit is set
otherwise the read will return -EIO.
This behavior causes the mst stream type1 capability test to fail to
read rx_info and determine if the topology supports type1 and fallback
to type0.
To fix this, check for type1 capability when we receive rx_info within
the AKE flow when we read RepeaterAuth_Send_ReceiverID_List instead
of an explicit read just for type1 capability checking.
This does require moving where we set stream_types to after
hdcp2_authenticate_sink() when we get rx_info but this occurs before we
do hdcp2_propagate_stream_management_info.
Also, legacy HDCP 2.0/2.1 are not type 1 capable either so check for
that as well.
Changes since v5:
- rename intel_set_stream_types() to intel_hdcp_prepare_streams()
(Anshuman)
Changes since v4:
- move topology_type1_capable to intel_digital_port and rename it as
hdcp_mst_type1_capable (Anshuman)
- make a helper function intel_set_stream_types() to set stream types
in hdcp2_authenticate_and_encrypt() (Anshuman)
- break on failure to set stream types and retry instead of returning
- remove no longer used declaration for streams_type1_capable()
Changes since v2:
- Remove no longer used variables in _intel_hdcp2_enable()
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-4-juston.li@intel.com
When reading RepeaterAuth_Send_ReceiverID_List, RxInfo is read by itself
once to retrieve the DEVICE_COUNT to calculate the size of the
ReceiverID list then read a second time as a part of reading ReceiverID
list.
On some MST docking stations, RxInfo can only be read after the RxStatus
READY bit is set otherwise the read will return -EIO. The spec states that
the READY bit should be cleared as soon as RxInfo has been read.
In this case, the first RxInfo read succeeds but after the READY bit is
cleared, the second read fails.
Fix it by reading RxInfo once and storing it before reading the rest of
RepeaterAuth_Send_ReceiverID_List once we know the size.
Modify get_receiver_id_list_size() to read and store RxInfo in the
message buffer and also parse DEVICE_COUNT so we know the size of
RepeaterAuth_Send_ReceiverID_List.
Afterwards, retrieve the rest of the message at the offset for
seq_num_V.
Changes in v5:
- Don't change the offset define for Send_ReceiverID_List
When reading, update message offset to account for RxInfo being read
Changes in v4:
- rebase and edit commit message
Changes in v3:
- remove comment
Changes in v2:
- remove unnecessary moving of drm_i915_private from patch 1
Signed-off-by: Juston Li <juston.li@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Reviewed-by: Anshuman Gupta <anshuman.gupta@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-3-juston.li@intel.com
Update cp_irq_count_cached when reading messages rather than when
writing a message to make sure the value is up to date and not
stale from a previously handled CP_IRQ.
AKE flow doesn't always respond to a read with a ACK write msg.
E.g. AKE_Send_Pairing_Info will "timeout" because we received
a CP_IRQ for reading AKE_Send_H_Prime but no write occurred between that
and reading AKE_Send_Pairing_Info so cp_irq_count_cached is stale
causing the wait to return right away rather than waiting for a new
CP_IRQ.
Signed-off-by: Juston Li <juston.li@intel.com>
Acked-by: Anshuman Gupta <anshuman.gupta@intel.com>
Reviewed-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Suraj K <suraj.kandpal@intel.com>
Signed-off-by: Anshuman Gupta <anshuman.gupta@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210819184835.1181323-2-juston.li@intel.com
Driver has to swap the endian before send brightness level value
to tcon.
v2: Use __be16 instead of u16 to fix sparse warning.
v3: Send one or two bytes brightness value depend on the precision.
v4: get data length of brightness value more easily.
Reported-by: kernel test robot <lkp@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-6-shawn.c.lee@intel.com
So far, DCS backlight driver hardcode (0xFF) for max brightness level.
MIPI DCS spec allow max 0xFFFF for set_display_brightness (51h) command.
And VBT brightness precision bits can support 8 ~ 16 bits.
We should set correct precision bits in VBT that meet panel's request.
Driver can refer to this setting then configure max brightness level
in DCS backlight driver properly.
v2: modify variable name brightness_precision_bits instead of
max_brightness_level.
v3: fix checkpatch warning.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-5-shawn.c.lee@intel.com
VDSC engine can process only 1 pixel per Cd clock. In case
VDSC is used and max slice count == 1, max supported pixel
clock should be 100% of CD clock. Then do min_cdclk and
pixel clock comparison to get proper min cdclk.
v2:
- Check for dsc enable and slice count ==1 then allow to
double confirm min cdclk value.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-4-shawn.c.lee@intel.com
According to chapter "Sending Commands to the Panel" in bspec #29738
and #49188. If driver try to send DCS long pakcet, we have to program
TX payload register at first. And configure TX header HW register later.
DSC long packet would not be sent properly if we don't follow this
sequence.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-3-shawn.c.lee@intel.com
Driver should wait for free header or payload buffer in FIFO.
It would be good to wait a while for HW to release credit before
give it up to write to HW. Without sending initailize command
sets completely. It would caused MIPI display can't light up properly.
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Vandita Kulkarni <vandita.kulkarni@intel.com>
Cc: Cooper Chiou <cooper.chiou@intel.com>
Cc: William Tseng <william.tseng@intel.com>
Signed-off-by: Lee Shawn C <shawn.c.lee@intel.com>
Reviewed-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Signed-off-by: Vandita Kulkarni <vandita.kulkarni@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210908115607.9633-2-shawn.c.lee@intel.com
Frontbuffer rendering will be dropped for modern platforms but
before that we to prepare DRRS for it.
intel_drrs_flush and intel_drrs_invalidate will not be called
for platforms that will not support frontbuffer rendering so DRRS
needs another way to be notified about to page flips so it can change
between high and low refresh rates as needed.
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210903221036.34770-3-jose.souza@intel.com
Both functions are pretty much equal, with minor changes that can be
handled by a single parameter.
v3:
- not scheduling work from invalidate operations
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210903221036.34770-2-jose.souza@intel.com
It started as a code style fix for the lines above 100 col but it
turned out to simplifications to intel_drrs_set_state().
Now it receives the desired refresh rate type, high or low.
v3:
- Fixed the mode refesh rate debug message
Cc: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Signed-off-by: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Gwan-gyeong Mun <gwan-gyeong.mun@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20210903221036.34770-1-jose.souza@intel.com
Avoid extra caching of the data. This is slightly more subtle than one
would think. For one thing, we explicitly ignore 0 value in child device
ddc pin; this is specified as N/A and does not warrant a warning. For
another, we start looking for ddc pin collisions in sanitize using
unmapped pin numbering.
v2: Check !devdata in intel_bios_alternate_ddc_pin()
Cc: José Roberto de Souza <jose.souza@intel.com>
Reviewed-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e1dbf7cbdd2191439e760ab9098242dcec5fbb2e.1630512523.git.jani.nikula@intel.com
